Casio 1995 User Manual

Module No.1995

1995-1

Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to carefully read this User’s Guide and keep it on hand for later reference when
necessary.

• Button operations are indicated using the letters shown in the illustration.

• This watch displays white figures on a black background, but all sample displays in this User’s Guide show black figures on a white background.

GENERAL GUIDE

CC

• Press

C to change from mode to mode.

CC

• The animation area shows different animated characters and graphics, depending on the mode and the operation being performed. Animated graphics also appear at the top of each
minute in the Timekeeping Mode.

• The watch automatically returns to the Timekeeping Mode if you do not perform any button operation for two or three minutes in any other mode.

ABOUT THIS USER’S GUIDE

Timekeeping Mode

Animation area

TIMEKEEPING MODE

• In the Timekeeping Mode, press
week screens. With the month screen, the animation area shows repeating charac­ters that indicate the current day of the week. With the day of the week screen, it
shows a G-mark.

Day of the week

PM indicator

Hour : Minutes Seconds

• In the Timekeeping Mode, press
formats.

• In the Timekeeping Mode, press

To set the time and date

1.Hold down

on the display. The seconds flash because they are

2.Press

3.While the seconds digits are selected (flashing), press

00. If you press
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.

4. While any other digits (besides seconds) are selected (flashing), press

crease the number. Holding down

5.After you set the time and date, press

• The day of the week is automatically set in accordance with the date.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode automatically.

About the backlight

Depending on the mode, pressing
onds. See the sections that cover each mode for information on whether you should

EE

press

E or

EE

• The backlight of the watch employs an electro-luminescent (EL) light, which loses
illuminating power after very long use.

• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.

• The watch will emit an audible sound whenever the display is illuminated. It does
not indicate malfunction of the watch.

• The backlight automatically stops illuminating whenever an alarm sounds.

Day

Day of the Week Screen

AA

A while in the Timekeeping Mode until the seconds digits start to flash

AA

CC

C to change the selection in the following sequence.

CC

Seconds
Day

DD

D while the seconds count is in the range of 30 to 59, the seconds

DD

BB

B.

BB

BB

B to switch between the month and the day of the

BB

Animation area

DD

D to switch between the 12-hour and 24-hour

DD

EE

E to illuminate the display for about two seconds.

EE

DD

D changes the current selection at high speed.

DD

EE

E or

EE

COUNTDOWN ALARM MODE

( )

Current time

Minutes

Seconds

Animation area

T➔M➔R

1/10 second

The countdown timer can be set within a range of 1 sec­ond to 60 minutes. When the countdown reaches zero,
an alarm sounds.

• In the Countdown Alarm Mode, press
the display for about two seconds. To illuminate the dis­play while setting the countdown time (while the min­utes or seconds digits are flashing), press

To set the countdown time

1.Hold down

the minutes digits start to flash on the display. The min­utes digits flash because they are

CC

2.Press

C to change the selection in the following se-

CC

quence.

Countdown Alarm Mode Stopwatch Mode Alarm Mode

DD

3.Press

D to increase the selected number. Holding down

DD

at high speed.

• To set the starting value of the countdown time to 60 minutes, set 00'00".

4.After you set the countdown time, press

• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Countdown Alarm Mode automati-

Animation area

( )

Month – Day

BB

Press

B

BB

selected

Hour

AA

A to return to the Timekeeping Mode.

AA

BB

B turns on the backlight for about two sec-

BB

AA

A while in the Countdown Alarm Mode until

AA

Minutes

Minutes

YearMonth

T➔U➔E

Month Screen

.

DD

D to reset the seconds to

DD

DD

D to in-

DD

BB

B to illuminate

BB

EE

E.

EE

selected

.

Seconds

cally.

To use the countdown timer

EE

Press

E while in the Countdown Alarm Mode to start the countdown timer.

EE

• When the countdown reaches zero, an alarm sounds for 10 seconds or until you
stop the alarm by pressing any button. The countdown time is automatically reset
to its starting value after the alarm stops.

EE

• Press

E while a countdown operation is in progress to pause it. Press

EE

resume the countdown.

• To completely stop a countdown operation, first pause it (by pressing

DD

press

D. This returns the countdown time to its starting value.

DD

About countdown indicators

An audible beep and the EL backlight keep you informed about the progress of the
countdown as noted in the following table.

Indication Start 5'00"0 Time Up

Beep 1 second 1 second 10 seconds
Backlight 1 second 1 second 2 seconds

STOPWATCH MODE

Animation area

( )

S➔T➔W

Current time

Minutes

Seconds

1/100 second

To record split times

EE

1.Press

E to start the stopwatch.

EE
DD

2.Press

D to display the timing up to that point. Stopwatch timing continues internal-

DD

ly.

DD

3.Press

D to clear the split time and to continue time measurement on the display.

DD

• You can repeat steps 2 and 3 as many times as you want.

EE

4.Press

E to stop the time measurement.

EE
DD

5.Press

D to clear the stopwatch to all zeros.

DD

To time first and second place finishes

EE

1.Press

E to start the stopwatch.

EE
DD

2.Press

D when the first finisher crosses the line, and record the time.

DD
EE

3.Press

E when the second finisher crosses the line.

EE
DD

4.Press

D to display the finishing time of the second finisher.

DD
DD

5.Press

D again to clear the stopwatch to all zeros.

DD

The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. You also get Auto-Start function.
The range of the stopwatch is 59 minutes, 59.99 seconds.

• In the Stopwatch Mode, press
play for about two seconds.

To measure elapsed time

EE

1.Press

E to start the stopwatch.

EE
EE

2.Press

E to stop the stopwatch.

EE

• You can resume the measurement operation by press-

EE

ing

E again.

EE

DD

3.Press

D to clear the stopwatch to all zeros.

DD

DD

D changes the selection

DD

AA

A to return to the Countdown Alarm Mode.

AA

EE

E again to

EE

EE

E), and then

EE

BB

B to illuminate the dis-

BB

About the Auto-Start function

With the Auto-Start function, the watch performs a 5-second countdown. When the
countdown reaches zero, stopwatch operation starts automatically. During the final
three seconds of the countdown, a beeper sounds with each second.

To use the Auto-Start function

Auto-start indicator

• To stop the Auto-Start countdown and return to the all-zeros display, press

EE

• Pressing

E while the Auto-Start countdown is in progress immediately start the

EE

stopwatch.

1.While the stopwatch display is showing all zeros
(00'00"00) in the Stopwatch Mode, press

• At this time the auto-start indicator appears on the dis-

play to indicate that auto-start is on. Press
turn auto-start off (indicated when the auto-start indica­tor is not on the display).

EE

2.Press

E to start the countdown.

EE

EE

• Pressing

E also causes the countdown time to appear

EE

in place of the current time.

• When the countdown reaches zero, a tone sounds, the

backlight illuminates the display, and a stopwatch tim­ing operation starts automatically.

DD

D.

DD

DD

D again to

DD

DD

D.

DD

ALARM MODE

Animation area

( )

A➔L➔M

Current time

Alarm on
indicator

Hourly time signal on
indicator

DD

3. Press

D to increase the selected digits. Holding down

DD

high speed.

• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.

• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning (no indicator) or afternoon (P indicator).

4.After you set the alarm time, press

• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.

To turn the Daily Alarm and Hourly Time Signal on and off

BB

Press

B while in the Alarm Mode to change the status of the Daily Alarm and Hourly

BB

Time Signal in the following sequence.

[Alarm ON Indicator / Hourly Time Signal ON Indicator]

When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. Press any button
to stop the alarm after it starts to sound.
When the Hourly Time Signal is turned on, the watch beeps
every hour on the hour.

• In the Alarm Mode (including alarm time setting), press

EE

E to illuminate the display for about two seconds.

EE

To set the alarm time

1. Hold down

• At this time, the alarm is automatically turned on.

Hour :

2.Press

Minutes

AA

A while in the Alarm Mode until the hour

AA

digits start to flash on the display. The hour digits flash
because they are

quence.

selected

.

CC

C to change the selection in the following se-

CC

Hour

DD

D changes the selection at

DD

AA

A to return to the Alarm Mode.

AA

Minutes

1995-2

Both OFFBoth ON

To test the alarm

DD

Hold down

D while in the Alarm Mode to sound the alarm.

DD

Daily Alarm
Only

Hourly Time
Signal only