Cashmaster Printer Zero User Manual

User Manual

CONTENTS

Connecting/disconnecting the printer.................… 1

Connecting power to the printer………….……...... 2

Installing paper...............………….……………...... 3

Operation.......................………….……………...... 4

Printer specifications............................................. 4

Global Support............………………….…..…….... 5

Faster, Accurate and Even More Intelligent

Copyright © 2009 Cashmaster International. All rights reserved. This document may not be copied
or reproduced in whole or in part, or transferred to any other media or language, by means without
the written prior permission of Cashmaster International. We reserve the right to make changes to
this document and to the product described herein without obligation to notify any persons of such
changes.

Connecting the scale to the printer

1. Place the printer on a level surface. See fig 1.

2. Lower the scale on to the printer so that the hooks at the front of the printer
engage with the apertures on the underside of the scale. See fig 2.

3. While holding the front of the scale down firmly against the printer with forefinger
and thumb of one hand, press down on the back of the scale with the other hand.
See fig 2. & 3.

CONNECTING/DISCONNECTING THE PRINTER

Disconnecting a scale from the printer

1. Place the printer with a scale attached on a level surface.

2. While holding the handle on the back of the printer with one hand, pull the back
of the scale up with the other hand. See fig 4.

3. Continue to lift the scale away from the printer until it completely disengages.

See fig 5. & 6.

1.

2. 3.

4. 6.

5.

1

Warning

Do not use a damaged or wet power adapter.
Do not connect power adapter with wet hands.
Do not disassemble the device, sensitive elements in the printer may be affected and this
will affect your warranty.

The printer has an internal battery that will supply power when the printer is not connected
to a mains supply, making the scale with printer attached completely portable. When a
12Vdc mains adapter is connected to the power supply socket, the scale will take its power
from this source and charge its internal battery. If the printer is attached to a scale, a 12Vdc
mains adapter may be connected to the power supply socket on either the printer or the
scale – power for operation and battery charging will automatically be shared between the
two devices.

CONNECTING POWER TO THE PRINTER

2

3

1. Place the printer on a level surface. See fig 1.

2. If the printer has a scale attached, disconnect it. See fig 2.

3. Press the blue printer mechanism release button firmly (this may be partially
obscured by paper if the last roll of paper has not been finished). See fig 3.

4. Fully raise the printer cover. See fig 4.

5. Remove any remaining parts of the last paper roll and place a new paper roll in
the paper roll cavity; ensuring paper will be fed from the underside of the roll.
See fig 5.

6. Pull the paper past the paper guides, over the printer mechanism and past the
front of the printer. See fig 6.

7. While holding on to the end of the paper and ensuring the paper is lying flat
and parallel to the paper guides, close the printer cover and press down firmly.
so that the printer mechanism clicks into place. See fig 7.

8. Tear of any excess paper by pulling the paper briskly upward and angled
against the teeth of the tear off edge.

INSTALLING PAPER

1.

2.

3.

4. 5. 6.

When the printer is connected to a scale, and the scale sends data to be printed, the printer
will print the data that has been sent. Paper may be fed through by pressing the paper feed
button on the left side of the printer.

While running on battery power, the scale will automatically go into sleep mode while it
is not being used to conserve battery power. The scale will wake up if; print data is sent
(return to sleep mode when print is complete), DC power is connected or the paper feed
button is held for more than 2 seconds (paper fed button will wake up the printer for 15
seconds, then it will return to sleep mode). While running on battery power there may be a
short delay before printing starts, because of the need to wake up the printer. While running
from a 12Vdc power adaptor, a LED in the centre of the paper feed button will indicate the
battery charge state.

OPERATION

4

PRINTER SPECIFICATIONS

Weight 0.62kg

Dimension 168mm (W) x 72mm (H) x 270mm (D)

Power Supply Mains adapter 12V 2.5A

LED red: Battery charging

LED green: Battery fully charged

LED flashing red/green: Very low battery charge – trickle charging

LED off: Power from battery only

Battery Type LiPo 7.4V 1250mAh

5

Document ID: 10308H

North America

t: [phone]
e: [e-mail]

Hong Kong and Asia

t: [phone]
e: [e-mail]

Germany

t: [phone]
e: [e-mail]

UK and all other customers

t: [phone]
e: [e-mail]

cashmaster.com

GLOBAL SUPPORT

www.cashmaster.com