Congratulations on your purchase of a Casablanca ceiling fan!
Your new fan will be a beautiful addition to your home, keeping you comfortable throughout
the year. The true appreciation of a Casablanca ceiling fan is only complete when put
into actual use. Great time and care have been taken to construct and enhance what are
otherwise functional appliances. Beauty is found in the integrity, craftsmanship, and attention
to detail. Thank you for looking for the
Your Casablanca fan was crafted with pride and care and inspected thoroughly prior
to shipment. Before you begin to assemble and install your fan, remove all parts
from the carton and check them against the Parts Guide in this manual.
Make sure all parts are included in the box
using the Parts Guide on the following pages.
If there are missing or broken parts:
Call 1-888-227-2178 Monday through Friday, •
7 a.m. to 4 p.m. PST. Your request will be
handled immediately. Replacement parts
will be sent to you via Federal Express.
Proper Parts Handling
Do not remove lightbulbs from their packaging •
until you are ready to install them.
Before discarding packaging materials, be •
certain that all parts have been removed.
Use a clean, dry paintbrush to remove small •
Styrofoam pieces that may remain after unpacking.
Do not brush Styrofoam into wiring cavities. •
The blades in each pack are matched for •
equal weight to assure smooth fan operation.
If more than one fan is being installed, do
not mix blades from different cartons.
Always turn power to the ceiling fan OFF before •
replacing lightbulbs or working on your fan.
Never insert anything into the path of the •
fan blades while the fan is in operation.
Never install a fan over a pool or spa. •
Never operate a fan that has been •
damaged in any way.
Install the fan according to the
instructions in this manual.
If the fan does not work:
Refer to the Troubleshooting Tips •
in this Owner’s Manual
Call Technical Support at 1-888-227-2178•
Contact your local Authorized Service Center•
Our Web site at www.casablancafanco.com contains
additional information on Casablanca products,
troubleshooting, and Authorized Dealer or Service
Centers. Please do not return this product to the store.
When cleaning, painting, or working near your •
fan, be cautious of the fan and blades.
RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION!
Please take a moment to locate the model number and serial number from your fan (see below) and record this
information on the Warranty page inside the front cover of this Owner’s Manual if it does not appear there already. These
numbers are found on the motor identification plate affixed to the fan motor in the following location as shown below:
Atria®
TYPE HANGER TYPE
POMONA, CA
Motor Identification Plate
SERIAL No.: DJ06 2237
C18G500F
DJ01 1151 MODEL #C18G500F
Serial Number
Model Number
2
Atria
Parts Guide
Item #DescriptionPicture (not to scale)Quantity
1.Motor Housing1
2.Crossbar Mounting Bracket1
3.Phillips Screwdriver1
4.Lag Screw and Washer1
™
5.1" x 8-32 Round-Head Screws and Washers 2
6.Canopy and Hatch1
7.2½" x 8-32 Canopy Screws and Lock Washers 5
8.Adapter Cover1
9.
4"Perma•Lock™DownrodandBallAssembly1
10.Allen Wrench1
11.Wire Nuts8
12.Light Fixture1
13.Light Fixture Screws2
14.C7 Incandescent Bulbs, 15W8
15.Blade Iron Support Ring1
3
Atria
™
Item #DescriptionPicture (not to scale)Quantity
16.Blade Iron Support Ring Screws5
17.Blade Irons
Blade Iron Screws (NOTE: Five of the eleven are found on the
18.
shipping blocks.)
19.Blades5
20.Blade Iron Plate Screws21
21.Blade Iron Plates5
22.Balance Kit1
23.Halogen Downlight Bulbs, 50W2
5
11
24.Glass Shade1
25.Light Kit Cap and Finial
26.W-81 Wall Control1
1 set
4
Product Specifications
Atria
™
Model name:Atria
Model number:C18GXXXF
ETL Rating:Damp
Dimensions:
Weight:42 lbs.
Motor Type:XTR200™
Motor Size:30mm
Blade Span:68"
Blade Iron Pitch:11˚
No. of Blades:5
Technology:W-81 wall control
Lightbulbs:(8) 15-watt C7 incandescent
*Performance data is for fan only. No lighting
wattage is included.
™
A = 23.4"
B = 28.8" NOTE: Dimension
C = 3"
D = 17.1 "
E = 5.6"
(2) 50-watt T4 halogen
B includes light
fixture and glass.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.•
This device must accept any interference •
received, including interference that
may cause undesired operation.
This equipment has been tested and found to
comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communication. However, there
is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between •
the equipment and receiver.
Connect the equipment into an outlet on a circuit •
different from that to which the receiver is connected.
Consult the dealer or an experienced •
radio/TV technician for help.
5
Atria
18"
↑
84"
↑
70"
↑
™
Safety Considerations
Safety and proper operation of your Casablanca fan both
require a thorough knowledge of the product and correct
installation; therefore, before attempting to install and
operate your fan, read this Owner’s Manual completely
and carefully. Retain this manual for future reference.
CAUTION: ÑRISK OF ELECTRICAL SHOCK!
Turn off all electricity at the circuit breaker
or fuse box before attempting any
installation procedure. Installation is to be
in accordance with the National Electrical
ANSI/NFPA 70-1999 and local codes. If
you are unfamiliar with the wiring codes,
contact a qualified electrician. To avoid
overheating and possible damage to
other equipment, do not install control
to a receptacle, fluorescent light fixture,
operating appliance, or transformersupplied appliance.
This ceiling fan requires a grounded electrical supply of •
120 VAC, 60 Hz and a minimum of 15-amp circuit. The
maximum current required for the fan with light fixture
if 2.9 amps. The fan uses about 1.1 amps (132 watts).
Fuse Box
(Remove fuse for the
circuit you will be
working on)
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
from bottom edge
of blade to oor
Where wire nuts are employed, be sure all •
bare wires are fully inserted into the metal wire
connectors inside the plastic wire nut covering.
When installing the canopy, light kit, and wall •
controls, make sure all wires are carefully
tucked away and that no wires are pinched.
The fan must be supplied with three •
independent 120V AC supply wires to provide
power for the fan, the light, and neutral.
WARNING: ÑDo not insert foreign objects
in between the rotating fan blades.
WARNING: ÑTo reduce the risks of fire or
electric shock, do not use this fan with any
solid-state control device. Use only the
control provided with or recommended for
this fan.
Dimensions indicated are the minimum
allowable for proper installation.
6
Atria
™
Mounting Guidelines
Before mounting your Casablanca fan, read the
following helpful recommendations. Location,
fan size, and structural support are important
factors to consider before installation.
Location
Ceiling fans have practical uses in almost every
room in your home. We suggest you follow
these mounting recommendations as you decide
where to install your Casablanca fan.
For safety reasons, the fan blades must •
be a minimum of 7' above the floor.
Do not locate the fan in a doorway •
or above a swinging door.
In bedrooms, fans work best when •
mounted above the foot of the bed.
Over pool tables, be sure to provide plenty of •
clearance to avoid damage from pool cues.
Structural Support
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where
you wish to place your Casablanca fan, an approved
ceiling fixture outlet box must be installed and wired.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either the circuit
breaker or fuse box), lower the old fixture and disconnect
the wiring. Check the ceiling fixture outlet box to be sure
it is marked “Approved for Ceiling Fan Mounting.” If it is
not, a new box must be installed. For new construction,
use an approved ceiling fixture outlet box with the rating
“50 lbs. or less”. Ensure that the outlet box is mounted to
a joist or stud beam. If not, a 2x4 stud must be installed.
WARNING! ÑTo reduce the risk of fire,
electrical shock, or personal injury, mount
to outlet box marked “Acceptable Fan
Support of 22.7 kg (50 lbs.) or less” using
the mounting hardware provided with the
outlet box.
In kitchens be sure to allow for open •
cupboard doors to clear the fan blades.
Do not install a fan close to or over a pool or spa. •
High humidity combined with corrosive gases
will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of
a full-size fan even in smaller rooms. For very
large rooms, two fans may be needed.
When to Use a Lag Screw
A lag screw is required under two conditions: the fan
weighs 36 lbs. or more, or the existing ceiling fixture
outlet box needs to be modified for a ceiling fan
application (for example, you are replacing an existing
light fixture with a fan). We recommend that the ceiling
box be of sufficient capacity to support the weight
of the fan and light fixture under any conditions.
NOTE: The Atria weighs 42 lbs., so use of a
lag screw is required.
7
Loading...
+ 15 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.