Casablanca Fan Company BELLA User Manual

BELLA

™

OWNER'S MANUAL

CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CONTROL FEATURES:

VERSA•TOUCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

READ AND SAVE THESE INSTRUCTIONS

SAFETY FIRST

Safety and the proper operation of y our Casablanca fan both requir e a thorough knowledge o f the product
and proper installation; therefor e, bef ore attempting to install and operate your Casablanca f an, read this
owner’s manual completely and carefully. Retain this manual for future reference.

CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.

BEFORE YOU START

• All wiring must be in accord ance with the N ation al Electric Codes an d the appropri ate local electrical cod es. Th e National

Electric Codes requires proper grounding as a precaution against electrical shock. A qualified electrician should be
consulted if you are unsure.

• This fan is design ed to be in stalled on an e xisting electri cal outlet bo x. Th e outlet bo x m ust be UL Listed for ceilin g f an
installations , if it is not, a n ew box must be in stalled. Casablan ca extensi on poles are available f or sloped or high ceilin g
installations.

• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.

• Where wire n uts are employed , be sur e all bare wir es ar e within the conn ectors. Wh en in stallin g the can opy hatch, mak e
sure all wires are within the canopy and that no wires are being pinched.

For best performance and for your warranty to be valid,

use only genuine Casablanca blades, light fixtures, and accessories.

• The blades in each pack are m atched for equal

weight to assure smooth fan operation. If
more than one fan is being installed, be
careful not to mix blades from different
cartons.

• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.

• It is always a good id ea to have an assistant
to help with the installation.

• When cleaning, painting, or working near
your fan, be very careful of th e fan and blades.
Always turn the power OFF to the ceiling f an
before servicin g it, working on it, or replacing
light bulbs.

• Never insert anything into the path of the
fan blades while the fan is in operation.

• Never install a fan over a pool or spa.

• Never operate a fan that has been damaged
in any way . Contact Casablanca Fan Compan y
by calling toll free 1-888-227-2178, or
contact your local authorized Casablanca
dealer for assistance in obtaining service.

P/N 9243010 REV.A P/D JUL01PDG

SAFE USE

FUSE BOX

(REMOVE FUSE FOR THE

CIRCUIT YOU WILL BE

WORKING ON)

CIRCUIT BREAKER

(TRIP BREAKER FOR THE

CIRCUIT YOU WILL BE

WORKING ON)

18″

84″

CAUTION: MOUNT WITH THE LOWEST MOVING
PARTS AT LEAST 2.5 METRES ABOVE FLOOR OR
GRADE LEVEL.
ATTENTION: INSTALLER DE SORTE QUELES
PIÈCES INFÉRIEURES SOIENT À AU MOINS 2.5
MÈTRES AU-DESSUS DU PLANCHER OU DU SOL.

1

MOUNTING RECOMMENDATIONS

Before moun ting your Casablan ca f an, read th e f ollowin g help ful recomm en dati on s. Th e locati on o f the f an, air cir culation,
and fan size are all important factors to consider before installation.

Location

Ceiling fans have pr actical uses in alm ost every r oom in your h om e . W e sugg est you f ollow th ese m ount­ing recommendations as you decide where to install your Casablanca fan.

• For safety reasons, the fan blades must be a minimum of 7′ above the floor.

• Do not locate the fan in a doorway or above a swinging door.

• In any installation, the tips of the blades must be at least 18″ from the wall in order to provide
sufficient clearance for the blades.

• In bedrooms, fans work best when mounted above the foot of the bed.

• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.

• In kitchens be sure to allow for open cupboard doors to clear the fan blades.

• Do not install a fan close to, or over, a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.

Fan Size

Variable f an speed capability permits the use o f a full-size 52″ fan even in sm aller
rooms. For very large rooms, two fans may be needed.

SLOPED CEILING INSTALLATIONS

Suggested Extension Pole Lengths

Ceiling Height

8′

8′ 6″

9′

9′ 6″

10′
11′
12′
13′
14′

Pole Length

Standard
Standard

6″
12″
12″
18″
24″
36″
48″

EXTENSION

POLE

MAXIMUM

HANG-TRU®

ANGLE 32º

BLADES MUST BE A

MINIMUM OF 7′

ABOVE THE FLOOR

32°

When to Use Extension Poles

For best performance and best appear ance,
an extension pole should be used with
your Casablanca fan when installing on
high (cathedral) ceilings or sloped ceil­ings. Casablanca offers standard poles in
increments of 6″ up to 5′. Custom poles
are available in lengths up to 10′. See your
Authorized Casablanca Dealer f or details.

Note: Fan may wobble or vibrate if

pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.

Calculation of 32°

Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.

2

7′ MINIMUM

EXAMPLE 1

This slope is less than 32˚.
It is OK to install your fan.

EXAMPLE 2

This slope is 32˚. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.

EXAMPLE 3

This slope is more than 32˚.
Your fan will n ot han g str ai ght d own, an
adaptor is necessary. Contact your local
Authorized Casablanca Dealer in regards
to purchasing a “Slope Ceiling Adaptor.”

BELLA

™

INSTALLATION INSTRUCTIONS

Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them

against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.

WORK BENCH SETUP

Setup. Remove the bottom foam from the box

and place the fan rightside up in the foam. This
protects the lamp socket during assembly.

NOTE: If this is the second Versa•Touch fan installed in the same
area, one of the fans MUST have its channel chang ed. Please refer
to the Versa•Touch section on the bottom of page 9.

NOTE: The fan weight is 30 pounds.

PERMA•LOCK™ HARDWARE

ALLEN SET SCREW

1

⁄4-20 x 1⁄4"

(PRE-INSTALLED)

3mm

ALLEN WRENCH

FAN PREPARATION

IMPORTANT SAFETY INFORMATION!

BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE

THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY

Prepare for fan installation as follows:
Step A. Place the downrod thr ough the motor cover as shown.

Route the wires from th e fan motor through th e Perma•Lock™
downrod and ball assembly.

MOTOR

COVER

WORK BENCH

GROUND

WIRE

FOAM

DOWNROD & BALL

ASSEMBLY

MOTOR

WIRES

DOWNROD

& BALL

ASSEMBLY

Tip: The downrod has a tapered thread

that is designed to lock completely wh en
correctly installed.

Step B. Using th e provid ed allen wrench, loosen the set scr ew
several turns to allow installation of the downrod. Thread
the downrod into the motor coupling until it stops turning,
this will take at least four and a half full turns.

Step C. Securely tighten th e set screw with the provi ded allen
wrench to ensure safe operation of your fan.

CAUTION: Failure to fully lock in the do wn­rod before secur ely tightening the allen set
screw may cause the fan to separate from
the downrod during normal operation!

ATTACH MOTOR COVER

Step D. Using the three screws provided, attach the motor

cover to the motor. Tighten firmly by hand only.

ALLEN

SET SCREW

MOTOR COVER

SCREWS (3)

TAPERED

THREAD

3