CARVIN LSx1202, LSx1202M, LSx1202A, LSx1501, LSx1502 User Manual

...

Download

Page 1

CARVIN ENGINEERING DATA LSx (LIVE SOUND) LOUDSPEAKERS

76-15230C 0508

LSx2153

LSx1002

Receiving inspection

INSPECT YOUR LOUDSPEAKER FOR DAMAGE which may have occurred during shipping. If damage is found, please notify the shipping company & CARVIN. SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit, always use the original carton and packing material. CARVIN and the shipping company are not liable for any damage caused by improper packing. SAVE YOUR INVOICE. It will be required for warranty service if needed in the future. SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately. Please allow several days for the rest of your order to arrive before inquiring. RECORD THE SERIAL NUMBER on the enclosed warranty card for your records. Return the warranty card with your name and comments to us, or register online at:

USA customers register online at: www.carvin.com/registration

All other countries register online at:

www.carvinworld.com/registration

LSx1502/LSx1502A

LSx1523/LSx1523A

LSx1503/LSx1503A

LSx1802

LSx1501 LSx1801/LSx1801A

LSx1202/LSx1202A

Carvin’s new LSx (Live Sound) Series loudspeakers give new meaning to high performance loudspeaker systems for today’s club scene. Building upon the company’s long-standing reputation for state-of-theart systems offering great sonic performance coupled with proven reliability and solid value, the new LSx Series loudspeakers deliver all the features musicians and mobile DJs demand.

Consisting of ten models encompassing five 2-way systems, three 3-way systems, and two subwoofer systems, the LSx Series is ideally suited to address a wide range of sound reinforcement system requirements—from intimate clubs to large scale, high impact music venues. With key features like steel grills to protect the drivers, recessed steel handles for easy transport, high order – low loss biampable crossovers that ensure high intelligibility of spoken word and accurate reproduction of music sources, plus Neutrik Speakon™ and quarter-inch connectors across all models, Carvin’s new LSx Series loudspeakers are just what your audience has been waiting for!

Going one step further, all LSx Series loudspeaker enclosures utilize multi-layered, cross grain laminated plywood construction. Why is this important? Unlike other materials, plywood construction results in rigid enclosure walls that reduce flex and sonic coloration caused by cabinet resonance, with the added benefit of a structurally more robust enclosure designed to handle the rigors of the road. Finished with great-looking, rugged Duratex™ sprayed on coverings, Carvin’s new LSx Series loudspeakers look every bit as compelling as they sound!

LiMiteD WaRRa nty

Parts and labor are covered for 3 years on manufacturer’s defects. Warranty does not cover burned out drivers caused by excessive power or distortion, or physical damage caused by general use, moisture or dust. CAUTION: Square wave distortion from power amps can destroy drivers much faster than clean RMS power. The power generated by the APS internal power amps has the capacity to damage the drivers, in which case they would not be covered under warranty.

seRvice

In the USA, please call 800-854-2235 for a RMA number (return authorization number). Write this number on the box and enclose a description of the problem. Prepay to Carvin 12340 World Trade Drive, SD, CA 92128

Outside the USA, contact your dealer or go to http://www.carvinworld. com for your nearest service center. Include a written description of the problem with serial number and date of purchase.

LSx1202M/LSx1202MA

LSx1502M/LSx1502MA

LSx1002 LSx1202 LSx1202A LSx1202M LSx1202MA

System Type: 10-inch 2-Way, bass-reflex 12-inch 2-Way, bass-reflex Active Bi-ampsystem 12-inch 2-Way, bass-reflex Active Bi-ampsystem

Frequency Response: 72 Hz – 20 kHz (-10DB) 70 Hz – 20 kHz (-10DB) 70 Hz – 20 kHz (-10DB)

85 Hz – 18 kHz (-3 dB) 76 Hz – 18 kHz (-3 dB) 76 Hz – 18 kHz (-3 dB)

Coverage Pattern: 60 degree round 90H x 60V 90H x 60V

Crossover: 2-Way 2-Way with Speaker Guard™ HF Active LF /HF Limiters 2-Way with Speaker Guard™ HF Active LF /HF Limiters

Crossover Frequency: 3.5 k Hz 2.5 k Hz 2.5 k Hz 2.5 k Hz 2.5 k Hz

Sensitivity (1w @ 1m)/ Max SPL: 98dB /121dB 97dB /122dB 127dB 97dB / 122dB 127dB

LF Driver: 10-inchwoofer 12-inch woofer 12-inch woofer

HF Driver: 1-inch titanium 1-inch titanium 1-inch titanium

Power: Continuous / Program / Peak Continuous/ Program / Peak Continuous / Peak Continuous / Program / Peak Continuous / Peak

Nominal Impedance full range: 8ohms 200w /400w /800 8 ohms 300w /600w /1200 350W / 700W 8 ohms 300w /600w /1200 350W / 700W

Bi-amp LF: 8 ohms 300w /600w /1200w 8 ohms 300w / 600w 8 ohms 300w /600w /1200w 8 ohms 300w / 600w

Bi-amp HF: 8ohms 50w /100w /200w 8 ohms 50w / 100w 8 ohms 50w /100w /200w 8 ohms 50w / 100w

Suspension/Mounting: 1-3/8-inch pole mount cup 1-3/8-inch pole mount cup none

Connectors: Two NL-4 Neutrik Speakon’s Two NL-4 Neutrik Speakon’s Two Bal. XLR Two NL-4 Neutrik Speakon’s Two Bal. XLR

Two ¼ TS phone jacks Two ¼ TS phone jacks One Bal. 1/4 TRS phone jack Two ¼ phone jacks OneBal. 1/4 TRS phone jack

Dimensions (H x W x D): 18 in x 12.5 in x 11.5 in 23 in x 15.5 in x 11.75 in 22.75 in x 15.5 in x 14.75 in

480 mm x 320 mmx 295 mm 585 mm x 395 mm x 300 mm 580 mm x 395 mmx 375 mm

Net Wt: 21 lb (10 kg) 33 lb (15 kg) 37 lb (17 kg) 33 lb (15 kg) 37 lb (17 kg)

Optional Accessories: CVS1002A cover CVS1202B cover CVS1202MA cover

LSx1502 LSx1502A LSx1502M LSx1502MA

System Type: 15-inch 2-Way, bass-reflex ActiveBi-amp system 15-inch 2-Way, bass-reflex ActiveBi-amp system

Frequency Response: 47 Hz – 20 kHz (-10DB) 47 Hz – 20 kHz (-10DB)

53 Hz – 18 kHz (-3 dB) 53 Hz – 18 kHz (-3 dB)

Coverage Pattern: 90H x 60V 90H x 60V

Crossover: 2-Way with Speaker Guard™ HF Active LF / HF Limiters 2-Way with Speaker Guard™ HF ActiveLF / HF Limiters

Crossover Frequency: 2.5 k Hz 2.5 k Hz 2.5 k Hz 2.5 k Hz

Sensitivity (1w @ 1m)/ Max SPL: 100dB / 129dB 127dB 100dB / 129dB 127dB

LF Driver: 15-inchwoofer 15-inch woofer

HF Driver: 1-inch titanium 1-inch titanium

Power: Continuous / Program / Peak Continuous / Peak Continuous / Program / Peak Continuous / Peak

Nominal Impedance full range: 8 ohms 400w /800w /1600w 350W/ 700W 8 ohms 400w /800w /1600w 350W/ 700W

Bi-amp LF: 8 ohms 400w /800w /1600w 8ohms 300w / 600w 8 ohms 400w/800w /1600w 8ohms 300w / 600w

Bi-amp HF: 8ohms 50w /100w /200w 8 ohms 50w / 100w 8 ohms 50w /100w /200w 8 ohms 50w / 100w

Suspension/Mounting: 1-3/8-inch pole mount cup none

Connectors: Two NL-4 Neutrik Speakon’s Two Bal. XLR Two NL-4 Neutrik Speakon’s TwoBal. XLR

Two ¼ TS phone jacks One Bal. 1/4 TRS phone jack Two ¼ TS phone jacks One Bal. 1/4 TRS phone jack

Dimensions (H x W x D): 25.75 in x 18.5 in x 11.75 in 25.75 in x 18.5 in x 15.75 in

655 mm x 470 mmx 300 mm 655 mm x 470 mmx 400 mm

Net Wt: 44 lb (20 kg) 49 lb (22.5 kg) 44 lb (20 kg) 49 lb (22.5 kg)

Optional Accessories: CVS1502B cover CVS1502MB cover

LSx1503 LSx1503A LSx2153 LSx1523 LSx1523A

System Type: 15-inch 3-Way, bass-reflex ActiveTri-amp system Dual 15-inch 3-Way, bass-reflex Dual 15-inch 3-Way, bass-reflex Active Tri-amp system

Frequency Response: 46 Hz – 20 kHz (-10DB) 45 Hz – 20 kHz (-10DB) 43 Hz – 20 kHz (-10DB)

52 Hz – 18 kHz (-3 dB) 51 Hz – 18 kHz (-3 dB) 49 Hz – 18 kHz (-3 dB)

Coverage Pattern: 90H x 60V 90H x 60V 90H x 60V

Crossover: 3-Way with Speaker Guard™ HF Active LF/MF/HF Limiter 3-Waywith Speaker Guard™ HF 3-Way with Speaker Guard™ HF Active LF/MF/HF Limiter

Crossover Frequency: 500Hz & 3.3 k Hz 500 Hz & 3.3 kHz 350Hz, 2.5 k Hz 500 Hz, 2.5 kHz 500Hz & 3.3 k Hz

Sensitivity (1w @ 1m)/ Max SPL: 101dB / 130dB 128 dB 101dB / 130dB 101dB / 130dB 128dB

LF Driver: 15-inchwoofer 15-inch woofer Dual15-inch woofer

MF Driver: 6-inch woofer 15-inch Woofer Dual 16-inch woofer

HF Driver: 1-inch titanium 1-inch 1.5” Dia. titanium 1-inch (1.5-inch Dia.) titanium

Power: Continuous / Program / Peak Continuous / Peak Continuous / Program / Peak Continuous/ Program / Peak Continuous / Peak

Nominal Impedance full range: 8 ohms 400w /800w /1600w 425w/ 850w 4 ohms 800w /1600w /3200 4 ohms 800w /1600w /3200 900W / 1800W

Bi-amp LF: ActiveTri-amp LF 8ohms 400w /800w /1600w 8 ohms 300w / 600w 4 ohms 800w /1600w /3200 4 ohms 800w /1600w /3200 4 ohms 700w / 1400w

ActiveTri-amp MF 8 ohms 75w / 150w 4 ohms 150w /300w /600w 4 ohms 120w / 260w

Bi-amp MF/HF: ActiveTri-amp HF 8ohms 200w /400w /800w 8ohms 50w / 100w 8 ohms 50w / 100w 8 ohms 50w / 100w 8 ohms 80w / 160w

Suspension/Mounting: 1-3/8-inch pole mount cup none none

Connectors: Two NL-4 Neutrik Speakon’s Two Bal. XLR Two NL-4 Neutrik Speakon’s TwoNL-4 Neutrik Speakon’s Two Bal. XLR

Two ¼ phone jacks One Bal. 1/4 TRSphone j ack Two ¼ TS phone jacks Two¼ TS phone jacks One Bal. 1/4 TRS phone jack

Dimensions (H x W x D): 28.75 in x 18.75 in x 15 in 43.75 in x 16.5 in x 15 in 46.75 in x 22.5 in x 15 in

730 mm x 480 mmx 380 mm 1110 mm x 420 mmx 380 mm 1190 mm x 570 mm x 380 mm

Net Wt: 58 lb (26.4 kg) 63 lb (28 kg) 73 lb (33 kg) 98 lb (45 kg) 106 lb (48 kg)

Optional Accessories: CVS1503A cover CVS2153A cover CVS1523Acover

LSx1801 LSx1801A LSx1802

System Type: 18-inch Sub, bass-reflex ActiveSubWoof er system Dual 18-inch Sub, bass-reflex

Frequency Response: 29 Hz – 265 Hz (-10DB) 24 Hz – 265 Hz (-10DB)

35 Hz – 150 Hz (-3 dB) 30 Hz – 150 Hz (-3 dB)

Active Protection

ActiveSub Limiter

Crossover: Low Pass Low Pass w ith High Pass Line Out Low Pass

Crossover Frequency: 150 Hz 80Hz or 120 Hz switchable 150 Hz

Sensitivity (1w @ 1m): 98dB / 127dB 128dB 102dB / 134dB

LF Driver: 18-inch woofer Dual18-inch woofer

Power: Continuous / Program / Peak Continuous / Peak Continuous / Program / Peak

8 ohms 400w /800w /1600w 4 ohms 800w /1600w /3200 700W / 1400W 4 ohms 1600w /3200w / 6400w

Suspension/Mounting: Top:1-3/8-inch Pole Mount Cup none

Connectors: Two NL-4 Neutrik Speakon’s Two Bal. XLR Two NL-4 Neutrik Speakon’s

Two ¼ TS phone jacks One Bal. 1/4 TRS phone jack Two ¼ TS phone jacks

Dimensions (H x W x D): 23.5 in x 19.75 in x 22.75 in 23.5 in x 40 in x 22.75 in

600 mm x 505 mmx 580 mm 600 mm x 1020 mmx 580 mm

Net Wt: 69 lb (31 kg) 77 lb (35 kg) 122 lb (55 kg)

Optional Accessories: CVS1801A cover

LSx1501

15-inch Sub, bass-reflex

37 Hz – 265 Hz (-10DB)

45 Hz – 150 Hz (-3 dB)

Low Pass

150 Hz

97dB / 123dB

15-inch woofer

Continuous / Program / Peak

Nominal Impedance full range:

Top: 1-3/8-inch Pole Mount Cup

Two NL-4 Neutrik Speakon

Two ¼ TS phone jacks

23.5 in x 19.75 in x 22.75 in

600 mm x 505 mmx 580 mm

56 lb (26 kg)

CVS1801A cover CVS1802A cover

Page 2

1. 1/4” inputs from power amp output (full range input only).

2. Speakon™ input from power amp (full range or biamp). Note: the Speakon pin configuration for biamping is: 1+ LF Positive / 1- LF Negative 2+ MF/HF Positive / 2- MF/HF Negative

3. Full Range/Biamp mode switch

4. Speakon™ through wired in parallel with input Speakon™.

5. 1/4” through wired in parallel with 1/4” input.

MULti-Way cRossoveR connections

(non-powered speakers) Us e either 1/4” or Speakon™ cables for connecting to the power amp and daisy chaining to an ad ditional speaker. For high powered and biamp applications, use Speakon™ cables only.

sUggestions FoR optiMaL peRFoRMance

• To help control feedback and to correct for venue characteristics, use a graphic EQ.

• For optimal coverage and dispersion, elevate high frequency horn above eye level.

• For optimal headroom, select an amplifier with a power capacity equal to or up to double the rated program power capacity of the loudspeaker system.

• Ensure all amplifiers are supplied and connected to properly rated AC power circuits. Underpowering amplifiers may cause premature clipping distortion.

speaKeR caBLes

Use either Carvin’s PRO50S speaker cable for up to 50’ or highcurrent 12GA Speakon™ cables for lengths up to 150’. 18GA cables are not recomended. You can DAISY-CHAIN up to one additional speaker per cable by using the OUTPUT connector. Be sure the total impedance to the amplifier is not lower than the amplifier’s minimum impedance.

Speakon Connector

Standard 1/4” Phone Plug Tip-Sleeve

Tip

Sleeve

Tip (Positive)

Sleeve (Negative)

Passive Non-Powered Models

1. 1/4” inputs from power amp output.

2. Speakon™ input from power amp. Note: the Speakon pin configeration is: 1+ LF Positive / 1- LF Negative 2+ not connected / 2- not connected

3. Crossover/Bypass mode switch to bypass internal crossover (must use active crossover when in bypass mode)

4. Speakon™ through wired in parallel with input Speakon™.

5. 1/4” through wired in parallel with 1/4” input.

LSx1523

4 OHMS

3200W PEAK

1600W PROG

800W CONTINUOUS

sUBWooFeR cRossoveR connections

LSx1802

4 OHMS

6400W PEAK 3200W PROG

1600W CONTINUOUS

20Hz 1 kHz 20 kHz

ATTENUATION dB

Low Frequency Mid Frequency High Frequency

Low Pass Filter

Band Pass Filter

High Pass Filter

LS1503A 300 Watts

75 Watts

50 Watts

LS1523A 700 Watts

120 Watts

80 Watts

1. inpUt/tHRU oUtpUt

Use the balanced XLR or 1/4” connectors featured on the rear control panel. Using a balanced source will reduce noise which may be picked up by the cable. You may DAISY-CHAIN as many APS systems as you wish. All connectors are wired in parallel.

2. eQUaLiZation

The APS powered loudspeakers offer a by passable 3-

band mid sweep equalizer for custom tuning to the acoustical environment. The EQ system is engineered specifically for the APS, featuring a boost and cut range of ±6dB to prevent radical adjustments that could otherwise compromise the sound of the system. The Mid-band sweep is particularly useful for enhancing critical mid range frequencies for stage monitoring or for cutting certain frequencies to compensate for room resonances. Press the “EQ IN” switch to activate the equalizer. The BLUE LED displays when the EQ is active.

3. LeveL contRoL

The LEVEL control adjusts the output volume of the APS. Start by setting the LEVEL at “0”. Weak input signals can be boosted by setting the LEVEL at “+6”. Strong signals can be reduced by turning the LEVEL toward “-12”. The RED LED will flash if the internal power amps start to clip. Turn the LEVEL control down to avoid clipping. Damage to the drivers can result from operating at a level where the RED CLIP LED is constantly illuminated.

4. poWeR/pRotect/cLip inDicatoR

Power up your audio source first, then turn on the APS with the power switch. When the system is active, the LED will indicate GREEN. When shutting down turn off the APS first, then turn off the mixer. If any of the power amps are clipping, the LED will indicate RED and you should reduce the output level. If the system should go into protect mode, the LED will indicate YELLOW and the power amps will shut off. This may occur if; a) the system is overheated due to clipping the power amps for an extended period of time, b) one of the internal drivers developed a short or c) the power amps require service.

5. poWeR

Push this switch to the UP position to apply power to the unit. The

POWER LED will light to show the system is on.

6. ac poWeR

Use a standard grounded AC cord. Whenever possible, use dedicated circuits for powered speakers. The powered speakers are available in either 120V or 240V models.

aps Bi-aMp/tRi-aMp ReaR paneL:

CAUTION ± TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY GROUND ON THE POWER CORD. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. WARNING ± TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

300VA120VAC 60Hz

AUS

MADE IN THE

Serial No.

TIME-ALIGNED BI-AMP SYSTEM

LOW MID SWEEP HIGH

+6-12

+6-6

1kHz

5kHz100Hz

300 W RMS

MID

+3-3

LEVEL

+6-6

+3-3

+6-6

+3-3

INPUTTHRU OUTPUT

CLIP

RED

PROTECT

YELLOW

POWER

GREEN

EQ IN

742A

5 6

LEVEL

LSx1801A

INPUTTHRU OUTPUT

ACTIVE SUBWOOFER SYSTEM

CLIP

RED

PROTECT

YELLOW

POWER

GREEN

FREQUENCY

OUTPUT

CROSSOVER

BYPASS

CROSSOVER 120Hz

80Hz

700W RMS

HI PASS

CAUTION±TO PREVENT ELECTRICAL SHOCK DO NOT DEFEATTHE SAFETY GROUND ON THE POWER CORD. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.WARNING± TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. REFER SERVICINGTO QUALIFIED PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

700VA120VAC 60Hz

Serial No.

+6-12

AUS

MADE IN THE

1588A

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

900VA120VAC 60Hz

AUS

MADE IN THE

Serial No.

TIME-ALIGNEDTRIAMPED SYSTEM

LOW MID SWEEP HIGH

+6-12

+6-6

1kHz

5kHz100Hz

900W RMS

MID

+3-3

LEVEL

+6-6

+3-3

+6-6

+3-3

INPUTTHRU OUTPUT

CLIP

RED

PROTECT

YELLOW

POWER

GREEN

EQ IN

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

300VA120VAC 60Hz

AUS

MADE IN THE

Serial No.

+6-12

1kHz

5kHz100Hz

LEVEL

+6-6

+3-3

CLIP

RED

POWER

GREEN

APS HOOK-UP

Lsx1801 sUBWooFeR

7. cRossoveR FReQUency sWitcH

The CROSSOVER FREQUENCY switch selects the crossover point for the APS. The 120Hz out setting is generally used with small to mid sized speakers in your setup. Almost all 12” and 15” woofers will benefit from the 120Hz setting. The 80Hz (switch in) setting is generally used with larger 18” woofers.

8. cRossoveR Bypass sWitcH

The crossover bypass switch bypasses the

internal active crossover allowing the use of an outboard active crossover.

9. Hi pass oUtpUt sWitcH

The hi pass output switch changed the output of the XLR thru output from a parallel of the Input XLR to a hi pass (all frequencies above) the crossover switch setting. This is good for going to a top cabinet that can not handle the sub’s low frequencies.

Powered Speakers

TIME IN DISTANCE + CROSSOVER PHASE SHIFT

APS POWER AMP SPECS:

2-way Bi-amped – LSx1502a/LSx1502ma–LSx1202a/LSx1202ma

350w Continuous/700w Peak RMS (Hi Freq: 50w @ 16 ohms, Lo Freq. 300w @ 8 ohms)

3-way Tri-amped – LS

x1503a

425w Continuous/850w Peak RMS (Hi Freq: 50w @ 16ohms, Mid Freq: 75w @ 16 ohms, Lo Freq. 300w @ 8 ohms)

3-way Tri-amped – LS

x1523a

900w Continuous/1800w Peak RMS (Hi Freq: 80w @ 16 ohms, Mid Freq: 120w @ 8 ohms, Lo Freq. 700w @ 4 ohms)

SuB woofer

– LSx1801a 700w Continuous/1400w Peak RMS @ 4 ohms

aLL modeLS:

FREQ. RESPONSE: 20 to 20kHz, THD less than .05% @ 90%, .1% at full power, SLEW RATE: 50V/µs, ACTIVE EQ: ± 6 dB @ 100 Hz, 100 Hz to 5 kHz mid sweep, 10kHz, EQ bypass switch, (SUB WOOFER: 24dB/Octave @ 80 & 120 Hz) • Relay muting and Speaker Guard™ protection, Peak and protection & power on indicators, On-Off power switch, Power Req. 120VAC 60 Hz . 240 AC/50Hz model available

Bi amped or Tri amped – active crossovers and power amps

All loudspeaker components are Time-Aligned

for greater intelligibility and clarity

Figure 2

Carvin’s APS (Active Powered Systems) ampliﬁcation packs take the guesswork out of selecting the ideal power source to drive your loudspeakers. With bi-amped and tri-amped models designed to handle the most demanding applications, the APS ampliﬁers are perfectly mated with—the LSx1502A, LSx1503A, and LSx1523A—creating optimally designed powered loudspeaker systems that are ready for anything you throw at them. There’s even one APS power pack created speciﬁcally to generate the bone crushing impact of our LSx1801A subwoofer. APS-based LS loudspeaker systems make setup and operation easier as well, with less gear to haul. Feed your mixer’s output directly to these loudspeaker systems, and you’re ready to rock!

ACTIVE POWERED SYSTEMS

APS

20Hz 1 kHz 20 kHz

ATTENUATION dB

Low Frequency High Frequency

Low Pass Filter

High Pass Filter

300 Watts

LS1502A

50Watts

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

WATER AND MOISTURE: Do not expose this appliance to rain or moisture. Do not use this apparatus near water (in a wet basement, near a swimming pool, bathtub etc). Care should be taken so that liquids are not spilled or splashed onto the unit. Do not place objects filled with liquids such as beverage containers on this apparatus.

POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. Unplug during lightning storms.

GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.

POWER CORD: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs and the point where they exit from the appliance. The plug or power inlet is the disconnect device and shall remain readily operable.

PLACEMENT: Do not block ventilation openings. Do not install near heat sources such as radiators, stoves or other products that produce heat. Do not install in a confined area. Use only mounting hardware such as brackets and tripods recommended by the manufacturer.

SERVICING: The user should not attempt to service the unit. All servicing should be referred to qualified service personnel. FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse. Refer to replacement text on

the unit for correct fuse type.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

LIMITED WARRANTY Your Carvin product is guaranteed against f ailure for 3 YEARS unless otherwise stated. Carvi n will service and supply all parts at no charge to the customer providing the unit is under warranty. S hipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FO R PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF T HE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR W ARRANTY. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or fail ure to follow instructions. This warranty is in lieu of all other warranties, expressed or impl ied. No representati ve or person is authorized to represent or assume for Carvin any liabi lity in connection with the sale or servi cing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. When R ETURNING merchandise to the factory, y ou must call for a return authorization number. If your unit is out of warranty, you will be charged the current FLAT RATE for parts and labor to bring your unit up to factory specifications.

HELP SECTION

1) UNIT WILL NOT TURN ON: Che ck the power to the AC c ord. Check for tripped circuit breakers, unplugged extension cords or power-strip switches that may be turned off. Check the fuse or circuit breaker on the unit if available. If the fuse has been replaced with the proper value and the fuse fails again, or the internal circuit breaker activ ates after reset, the unit will require servicing.

2) NO OUTPUT with POWER light ON: Shipping damage will be the primary reason for your product to not function properly. Please give us a call to help you determine the problem.

3) KEEP YOUR UNIT LOOK ING NEW: Use only a dry cloth to wipe the control a nd venting areas. Surfaces without openings may be c leaned with a damp cloth.

THIS UNIT CONTAINS HIGH VOLTAGE INSIDE!

REFER SERVICING TO A QUALIFIED TECHNICIAN

CAUTION

typicaL LoUDspeaKeR iMpeDance conFigURations

Individual speaker or speaker cabinet wiring examples for total impedance.