Page 1
IN EAR MONITOR SYSTEM
EM900
Page 2
CARVIN ENGINEERING DATA
EM900
PG. 2
WARRANTY
This CARVIN AUDIO product is guaranteed in normal use to be free from electrical and mechanical defects for a
period of ninety days from date of purchase. Retain proof of purchase. This warranty is in lieu of any and all other
guarantees or warranties, expressed or implied. There shall be no recovery for any consequential or incidental
damages.
INTRODUCTION
Thank you for purchasing the Carvin
Audio EM900 In Ear Monitor System.
The features and sound will give you
a new level of monitoring quality that
you have never experienced before.
The following information found in
this manual will help you get the
most enjoyment and functionality
from your new EM900.
EM900 / EM901 SPECIFICATIONS
» Frequency Response : 30Hz-15kHz
» S/N ratio : 80dB (A weighted)
» Image frequency rejection : 80dB
» Channel separation : 35dB
» Input level switch : 0dB / -10dB
» AC Mains input : 100V-240V (50-60Hz)
» Receiver power : 2AA batteries
» Battery life : 8 hours
» Net Weight : Base 3.2lbs Receiver .45lbs
» Dimensions : Base (EM900) 8.35”W x 9”D x 1.75”H
» Dimensions : Receiver (EM901) 4.5”H x 2.75”W x 1”D
EM902 EAR BUD SPECIFICATIONS
» Frequency Response : 20Hz-20kHz
» Type : Dynamic
» Impedance : 16 ohms
» Sensitivity @ 1kHz : 114dB/mW
» Distortion : less than 0.3%
» Cord length : 58” Inches
SYSTEM INCLUDES :
» 1 EM900 Base Transmitter with antenna
» 1 EM901 Body Pack Receiver
» 1 Pair of EM902 High Definition Ear Buds
KEY FEATURES
» UHF Operation with PLL technology
provides a reliable signal connection
» 960 selectable channels with Hi
Frequency boost option
» 4 channel groups with 16 presets
allow for quick setup
» Built in audio limiter to control peak
signals
» Receiver features XLR and 1/4-inch
inputs
» Lockout mode prevents accidental
adjustments
» Stereo or mono operation with
volume and balance controls
IMPORTANT PRECAUTIONS
» Make all connections before AC
power is connected
» Avoid exposure to high temperature
or humidity
» Do not handle the transmitter or AC
cord in wet conditions
» Keep away from heat and flame
» Avoid prolonged listening at high
levels. Refer to the OSHA table on
page 7.
Page 3
CARVIN ENGINEERING DATA
EM900
IN EAR MONITOR SYSTEMIN EAR MONITOR SYSTEM
PG. 3
EM900 Front Panel
» 1. POWER SWITCH
» 2. D I SP LAY
» 3. (+) BUTTON
» 4. SET BUTTON
» 5. (-) BUTTON
» 6. VOLUME CONTROL
EM900 Rear Panel
» 10. AC MAINS SOCKET
» 11. LOOP OUTPUT JACKS
» 12. INPUT - XLR & 1/4”-inch
» 13. ANTENNA CONNECTOR
EM901 Receiver
» 14. POWER SWITCH / VOLUME
» 15. BALANCE CONTROL
» 16. 1/8” (3.5MM) HEADPHONE JACK
» 17. DIS P LAY
» 18. (+) BUTTON
» 19. SET BUTTON
» 20. (-) BUTTON
» 21. BELT CLIP
» 22. BATTERY PACK
» 7. MONITOR VOLUME
» 8. STEREO MONITOR JACKS
» 9. ANTENNA
1
9
2
3
4
6 7
8
5
10
11
12
13
17
18
19
21
20
22
16
15
14
Page 4
PG. 4
EM900 TRANSMITTER OPERATION
» 1. ATTACH ANTENNA : Plug the antenna into the
rear panel BNC connector (#13) and rotate the
barrel 90 degrees clockwise until it locks into
place.
» 2. ATTACH AC POWER CORD : Firmly insert the
provided AC cord into the rear panel AC power
socket (#10).
» 3. CONNECT INPUTS TO SOURCE : Using XLR
or 1/4-inch plugs, connect the output
of your mixer to the input jacks (#12) on the rear
panel of the EM900 transmitter. One jack may be
used if the transmitter and receiver are set for
“MONO”. Adjust the balance knob (#15) on the
EM901 body pack receiver to the center position.
FREQUENCY SELECTION
You can choose the transmitting frequency
manually or use the group / channel preset feature (see
group and channel setting in the section below).
» 1. Hold down the SET button (#4) until “Freq” starts
flashing. Use the (+) and (-) buttons to choose the
desired frequency. Adjustments can be made in
25kHz increments.
» 2. Press the SET button to store the frequency.
The transmitting frequency is now stored in the
EM900 transmitter.
GROUP AND CHANNEL SETTING SELECTION
The group and channel feature is designed to make
operating multiple EM900 transmitters easier by using pre
selected frequencies within a group, There are 4 groups
available (A,B,C or D). There are 16 frequencies within
each group specifically calculated to reduce inter
modulation between the other frequencies in the group.
To select a group and channel do the following:
» 1. Hold down the SET button (#4) until “Freq” starts
flashing. Press the SET button (#4) one time. With
the “GROUP” now flashing, use the(+) button to
select one of 4 groups (A,B,C or D).
» 2. Press SET button again (#4) and use the (+) and (-)
buttons to SET the desired channel (1 - 16). Press
SET again to store both the group and channel
selection into the EM900 transmitter.
EM900 REAR
* Frequency shown is example only. Current
EM900 operates in the 500MHz spectrum.
EM900 Display
STEREO OR MONO/MIX SETTING
In Stereo mode, both inputs are used to provide a left /
right stereo image to the listener. In MONO mode, one or
both inputs can be used depending on your needs. When
using just one input, use CH.1 input on the EM900 transmitter. Using both inputs (CH1,CH2) while in MONO mode
allows you to send 2 different mixes to the receiver
» 1. Hold down the SET button (#4) until “Freq” starts
flashing. Press the SET button three times.
With “MODE” now flashing, use the(+) and (-)
buttons to select between mono and stereo
modes on the EM900 transmitter.
» 2. Press SET again to store the stereo/mono mode
into the EM900 transmitter.
ATTENUATION MODE
In some situations, the incoming signal to the
EM900 transmitter needs to be reduced to prevent the
input from being distorted. The EM900 has a -10dB
attenuator that can be activated.
» 1. Hold down the SET button (#4) until “Freq” starts
flashing. Press the SET button four times. With
“ATT” now flashing, use the (-) button to activate
the -10dB attenuation.
» 2. Press SET again to store the attenuation setting
into the EM900 transmitter.
LOCK MODE
In some situations, you may want to prevent
accidental changes with the EM900 transmitter
settings. The lock mode can be activated to
protect your EM900 settings.
» 1. Hold down the SET button (#4) until “Freq” starts
flashing. Press the SET button five times. With
“LOCK” now flashing, use the (+) button to activate
the lock setting.
» 2. Press SET again to store the lock setting
into the EM900 transmitter.
» 3. To unlock the EM900, simply hold down the SET
button (#4) until “LOCK” starts flashing, then press
the (-) to unlock the unit. Press the SET button to
store the unlocked mode into the EM900.
Page 5
CARVIN ENGINEERING DATACARVIN ENGINEERING DATA
SET UPSET UP
IN EAR MONITOR SYSTEMIN EAR MONITOR SYSTEM
PG. 5
22
EM901 Receiver
» 14. POWER SWITCH / VOLUME
» 15. BALANCE CONTROL
» 16. 1/8” (3.5MM) HEADPHONE JACK
» 17. DIS P LAY
» 18. (+) BUTTON
» 19. SET BUTTON
» 20. (-) BUTTON
» 21. BELT CLIP
» 22. BATTERY PACK
15
16
17
18
19
21
20
EM901 RECEIVER
» 1. INSERT BATTERIES : First, remove the battery
pack from the receiver by pressing in the two tabs
(see fig.1) at the bottom of the unit and sliding out the
battery pack. Open the battery pack by pushing down
first, then slide the battery cover off (see fig.2). Insert
the batteries as shown on the battery pack (fig. 3a). Slide
the cover back into position by pushing down first, then
slide the cover on to secure the batteries. Insert battery
pack into the EM901 receiver.
FIG. 2
FIG. 3a
◀
◀
FIG. 3b
EM901 RECEIVER SET UP
* Frequency shown is example only. Current
EM900 operates in the 500MHz spectrum.
EM901 Display
FIG. 1
◀
◀
◀
◀
FREQUENCY SELECTION
You must set the frequency of the EM901 to match the
frequency of the EM900 base transmitter. If using the
group/channel feature, see group and channel setting
in the section below.
» 1 Turn the EM901 to the on position by rotating
the ON/VOL knob (#14). Hold down the SET
button (#19) until the MENU list is visible. Press
the SET button again to select frequency. Use
the (+) and (-) buttons to choose
the desired frequency. Adjustments can
be made in 25kHz increments. .
» 2. Press the SET button, then the (+) #18 to confirm
the frequency. The frequency is now stored in
the EM901 receiver. Pressing the (-) #19 will
cancel the operation and bring you back to the
MENU list.
» 3. Once the frequency adjustments have been
made, press the (-) button to scroll down to “exit”
and press the SET button. The EM901 is now
ready for operation.
GROUP AND CHANNEL SETTING SELECTION
If using the group and channel feature follow the steps
below.
» 1. Hold down the SET button (#19) until the MENU
list is visible. Press the (-) button (#20) one time
to select “Group/Channel”. Press the SET button
again. Use the (+) and (-) buttons to select one of
the four groups (A,B,C or D).
» 2. Press the SET button, then the (+) #18 to confirm
the setting. the Group/Channel is now stored in
the EM901 receiver. Pressing the (-) #19 will
cancel the operation and bring you back to the
MENU list.
» 3. Once the Group/Channel selection has been
made, press the (-) button to scroll down to “exit”
and press the SET button. The EM901 is now
ready for operation.
14
Page 6
PG. 6
STEREO OR MONO/MIX SETTING
Select whether the EM901 operates in Stereo or Mono
mode. In Mono mode one or both inputs on the EM900
transmitter can be used. In the case of using two inputs,
the balance mix of the 2 inputs are adjusted by using the
balance control knob #15 on the belt pack.
» 1. Hold down the SET button (#19) until the MENU
list is visible. Press the (-) button (#20) to select
“Stereo/Mono”. Press the SET button again. Use
the (+) and (-) buttons to select the desired mode.
» 2. Press SET to store and return to the MENU.
» 3. Press the (-) button to scroll down to “exit”
and press the SET button. The EM901 is now
ready for operation.
HIGH FREQUENCY BOOST SETTING
The Hi Freq. Boost raises treble output in the mix. If the
sound becomes distorted at high volumes, turn this feature OFF, or reduce the levels.
» 1. Hold down the SET button (#19) until the MENU
list is visible. Press the (-) button (#20) to select
“Hi-Freq Boost”. Press the SET button again. Use
the (+) and (-) buttons to select ON or OFF.
» 2. Press SET to store and return to the MENU.
» 3. Press the (-) button to scroll down to “exit”
and press the SET button. The EM901 is now
ready for operation.
LIMITER
The dynamic limiter reduces volume peaks to help protect your hearing and increase your listening
experience.
» 1. Hold down the SET button (#19) until the MENU
list is visible. Press the (-) button (#20) to select
“Limiter”. Press the SET button again. Use the (+)
and (-) buttons to select ON or OFF.
» 2. Press SET to store and return to the MENU.
» 3. Press the (-) button to scroll down to “exit”
and press the SET button. The EM901 is now
ready for operation.
LCD DISPLAY CONTRAST
Adjust the contrast of the EM901 display using the
CONTRAST feature.
» 1. Hold down the SET button (#19) until the MENU
list is visible. Press the (-) button (#20) to select
“Contrast”. Press the SET button again. Use the (+)
and (-) buttons to adjust desired contrast.
» 2. Press SET to store and return to the MENU.
» 3. Press the (-) button to scroll down to “exit”
and press the SET button. The EM901 is now
ready for operation.
DISPLAY BACKLIGHT
To conserve battery life, the display backlight can be shut o
at various time settings ranging from always on, 30 , 20 , 10 ,
5 , 2 , 1 seconds and always o. Keeping the backlight ON will
greatly reduce the battery life.
» 1. Hold down the SET button (#19) until the MENU
list is visible. Press the (-) button (#20) to select
“Light Time”. Press the SET button again. Use the
(+) and (-) buttons to adjust desired backlight time.
» 2. Press SET to store and return to the MENU.
» 3. Press the (-) button to scroll down to “exit”
and press the SET button. The EM901 is now
ready for operation.
KEY LOCK
The key lock feature prevents accidental changes to the
EM901 receiver during use.
» 1. Hold down the SET button (#19) until the MENU
list is visible. Press the (-) button (#20) to select
“Key-Lock”. Press the SET button again. Use the (+)
button to select ON. Press the SET button again.
The Key Lock is now engaged as indicated by the
key icon.
» 2. To unlock, Press SET and then the (+) key.
EM902 EAR BUDS
The EM902 ear buds are designed to give you an
unparalleled listening experience. Proper care and use will
extend the life of the ear buds and maximize your user
experience.
» 1. Plug the EM902 earphones into the headphone
jack (#16) on the receiver. Attach a pair silicone
sleeves to the ends of the earphones.
» 2. Follow the “L” and “R” markings on the earphones
for left and right ear. Place the end of the
earphone at the end of the ear canal and
set the body of the earphone so your outer
ear will hold it in place. The earphones should be
worn with the wire hanging over
the top of the ear.
EM902 EAR BUDS
Page 7
CARVIN ENGINEERING DATACARVIN ENGINEERING DATA
SET UPSET UP
IN EAR MONITOR SYSTEMIN EAR MONITOR SYSTEM
PG. 7
LEVEL MAX TIME
>115dB SPL NONE
115dB SPL 28 seconds
112dB SPL 56 seconds
109dB SPL 1 minute 52 seconds
106dB SPL 3 minutes 45 seconds
103dB SPL 7 minutes 30 seconds
100dB SPL 15 minutes
97dB SPL 30 minutes
94dB SPL 1 hour
91dB SPL 2 hours
88dB SPL 4 hours
85dB SPL 8 hours
82dB SPL 16 hours
80dB SPL 24 hours (continuous)
Part# Description
EM900ANT
Replacement antenna for
EM900
EM901BATT
Replacement battery
compartment
EMBATCLIP-4
Set of 4 battery
compartment retention clips
EM901CLIP EM901 body pack clip
OSHA Recommended Maximum Exposure
Time To Avoid Hearing Loss
ADVANCED SETUPS:
» A. MULTIPLE SYSTEMS: Up to 16 separate EM900
transmitters can be used at one time, with
unlimited EM901 receivers.
» B. MULTIPLE RECEIVERS: To use multiple
receivers to monitor the same mix, simply set
the receivers to the same frequency as the
transmitter. Additional EM901 receivers
are available from Carvin Audio.
» C. MULTIPLE TRANSMITTERS WITH SAME MIX:
To connect multiple transmitters
to the same source, connect 1/4” cables
from the LOOP OUT connector of the first unit
into the INPUTS of the second unit. This can be
useful in areas with very
unpredictable RF conditions to provide better
coverage and for redundant backups.
SPARE PARTS
EM900 Audio Out
Page 8
carvinaudio.com
EM900 2018-2-06
Loading...