Carvin 1588 V1 User Manual

SPEAKER CABLES

Our standard cable for speaker hookups is the PH50. This cable features 1/4”
plugs and 16 gauge copper wire. The PH50 is adequate for lengths up to 50’ under
normal use. You can DAISY-CHAIN up to one additional speaker per cable by using
the unused 1/4” OUTPUT” jack (right side) on your speaker jack plate. Be sure to
note the total impedance to the amp so it is not lower than it’s recommended
impedance. See

Typical Loudspeaker Impedance Configurations.

Our professional SPK25, SPK50 & SPK100 cables feature Speakon™ lock-on
connectors with heavy 4 conductor 12 gauge copper wire. These cables are to be
connected in the same way as the PH50 with compatible amps.

PRECAUTIONS

1) DO NOT EXCEED THE POWER RATING marked on the rear connect plate.
Excessive power will destroy drivers. 2) DISTORTION from power amps will destroy
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are
harmful to drivers causing failure which is not covered under warranty.

WARRANTY

CARVIN loudspeakers are covered by a ONE year limited warranty unless
otherwise stated. Warranty coverage is limited to original manufactures defects
only. WARRANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn
cones caused by improper packing or abuse. 3) Damage from rain, moisture, ETC.
When returning defective driver(s), remove them from the enclosure to reduce
shipping costs . DO NOT stuff paper into the driver(s). Return pre-paid by UPS.
Include your address and description of the problem. Your driver(s) will be
returned COD for the cost of shipping and reconditioning if not covered under
warranty.

MODEL 1588 SPEAKER SYSTEM SPECS:

Frequency Response: 45 Hz to 19 kHz ±3 dB

Useable Low Frequency: 34 Hz (-10 dB)

Power Handling: 800w Continuous Power

Recommended Amp: 100 to 1200 watts

Sensitivity: 103 dB SPL, 1 Watt @ 1 meter

Coverage Angles: 90°Horizontal, 45°Vertical

Nominal Impedance: 4Ω

Crossover Type:

C1588 Constant Voltage

Inputs/Outputs: Two 1/4", two Speakon™

Bi-Amp Support: Yes—Panel Switch

Horn Driver Protection: Yes—Exciter Lamp

Woofer Enclosure Type: V ented Box

Enclosure Covering: Black Duratuff II™

Dim/Wt: 25"W x 19.25"D x 48.5"H, 124 lbs.

Optional Cables: PH50, SPK25, SPK50, SPK100

Optional Vinyl Cover: CVS1588

1588 FREQUENCY RESPONSE

CARVIN ENGINEERING DATA

1588 SPEAKER SYSTEM

INSTRUCTIONS

1588

Congratulations on your selection of the 1588 loudspeaker. As the big brother of the 3­way 1584, the 1588 Loudspeaker benefits from the same state-of-the-art design and
response characteristics, but with one obvious difference—it has twice the size, with twice
the components. This translates into an obvious benefit—much more sound output and
power with the same extraordinary response as the smaller version. In fact, there isn't any
application that this 800 watt 3-way system can't handle, tackling anything from large
clubs to outdoor concerts. Like the smaller 1584, the 1588 gives you what other 3-way
loudspeakers don't—studio quality sound in large sound reinforcement applications.

The low frequency subsystem of the 1588 utilizes two heavy-duty 15” woofers, chosen
for their extended bass response at high levels. The midrange employs two 8” direct
radiating midrange drivers, for their exceptionally smooth and extended frequency
response. The high frequency consists of one highly accurate titanium horn driver and
lens assembly. All components are integrated with our 3-way C1588 crossover to deliver a
system response that is smooth from 34 Hz to 19k Hz. Bi-amping can easily be done by
selecting the bi-amp switch and input connectors.

RECEIVING INSPECTION

INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during

shipping. If any damage is found, please notify the shipping company & CARVIN.

SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the best
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage caused by improper packing.

SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.

SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.

RECORD THE SERIAL NUMBER on the enclosed warranty card. Keep your portion of

the card and return the portion with your name and comments to us.

SUGGESTIONS FOR OPTIMAL PERFORMANCE

Raise the enclosure to the ear level of your audience for greater coverage. To help
control feedback, use a graphic equalizer. Keep the speakers in front of the
microphone. Never direct the microphone towards the speaker. For greater
coverage, add a second speaker system 20° to 30° off axis.

TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS

Individual speaker or speaker cabinet wiring examples for total impedance.

SERIES CONNECTION

16Ω TOTAL IMPEDANCE

+

+

+

PARALLEL CONNECTION

4Ω TOTAL IMPEDANCE

+

+

+

8Ω TOTAL

IMPEDANCE

SERIES/PARALLEL

CONNECTION

8Ω TOTAL IMPEDANCE

+

+ +

+

+

+

+

8Ω

8Ω

8Ω

8Ω

8Ω

8Ω

8Ω

4Ω8Ω

8Ω

16Ω8Ω8Ω

REAR CONNECT PLATE

Two standard 1/4” phone
jacks and two Speakon™
connectors are featured. See
other side for hookup
diagrams.

76-01588 0298

12340 World Trade Drive, San Diego, CA 92128

[phone] [phone]

www.carvin.com

MIXER POWER AMP

OUT

ADDITIONAL

SYSTEM

1588

SPK OUTINPUT

Toll Free 1-800-854-2235

USA

1

5881

PROFESSIONAL SOUND REINFORCEMENT

MADE IN THE

USA

SPEAKER SYSTEM

MODE SWITCH: FULL RANGE

BIAMP

FULL

RANGE

FULL RANGE–INPUT

BIAMP SW–HI FREQ. INPUT 4Ω

FULL RANGE –PARALLEL

BIAMP SW–LOW FREQ. INPUT 4Ω

4 Ω 800 Watts

JACKS WIRED

PARALLEL IN FULL

RANGE MODE

Speakon™

1+SIGNAL

1–GROUND

2+ & 2–

NOT USED

5881

PROFESSIONAL SOUND REINFORCEMENT

MADE IN THE

USA

SPEAKER SYSTEM

MODE SWITCH: BIAMP

BIAMP

FULL

RANGE

FULL RANGE–INPUT

BIAMP SW–HI FREQ. INPUT 4Ω

FULL RANGE –PARALLEL

BIAMP SW–LOW FREQ. INPUT 4Ω

4 Ω 800 Watts

JACKS WIRED

PARALLEL IN FULL

RANGE MODE

Speakon™

1+SIGNAL

1–GROUND

2+ & 2–

NOT USED

ELECTRONIC CROSSOVER

MIXER

OUT

IN (Set FREQ 600Hz) HILOSUB

MIXER POWER AMP

SPK OUTINPUT

USA

1

HOOKUP DIAGRAMS

NORMAL FULL RANGE HOOKUP

BI-AMP HOOKUP