EASY TO RUN
MESSAGES SPELLED
MESSAGES SPELLED
OUT IN 8 LANGUAGES
OUT IN 8 LANGUAGES
● Auto Start/Stop
● Continuous Run
● Temperature Setpoint
● Pretrip Check
● Alarm Display/Reset
CHECK OUT
THESE FUNCTIONS
CARRIER TRANSICOLD EUROPE S.A.S.
10-12, bd de l’Oise
F-95031 CERGY PONTOISE CEDEX
Phone : + 33 (0) 1 34 43 48 00 - Fax :+ 33 (0) 1 34 43 48 48
500 CARRIER SERVICE STATIONS in EUROPE,
FORMER SOVIET UNION, MIDDLE EAST and AFRICA
Our company is constantly seeking to improve the quality of its products and, therefore,
reserves the right to modify its products without prior notice
Carrier Transicold Europe S.A.S.- S.A.S. au capital de 16 090 700 euros
R.C.S.Pontoise B 410 041 776 - Code APE 292 F - VAT : FR52410041776
The information contained in this document is not contractually binding,
and may not be reproduced without prior approval - 62-60556-00
● Trip Start
● Function Change
● Unit Data
● Manual Defrost
● Manual Operation
● Standby Operation
● Stopping
62-60556-00
FOR YOUR
PROTECTION
EASY TO
STOP
Safety
Your CARRIER product has been designed to meet all
European Safety requirements.
Please take notice of all stickers that have been placed on
this product for your safety.They are for your PROTECTION !
Unit may start automatically.
Top up coolant into recovery bottle only.
Fill empty radiator through filler neck slowly to avoid air
entrapment.
Remove filler cap slowly.
Disconnect battery before doing any electrical welding on unit or
trailer. This unit has a negative ground system.Do not reverse polarity .
Reverse polarity will cause immediate failure of electrical system.
Replace cover after servicing battery to insure protection of
battery and terminals.
The refrigerant contained in the refrigeration system
of your unit can cause frosbite, severe burns, or blindness when in direct contact with the skin or eyes.
Beware of fan blades and pulleys.
Stopping
SETPOINT
=
Place RUN / STOP switch to STOP to stop
1
1
unit.
DEFROST
MANUAL
START-STOPALARMDEFROSTCOOLHEAT
BOX TEMPERATURE
DATAPRETRIP
ALARM LIST
!
CONTINUOUS
FUNCTION
CHANGE
START-STOP
CONTINUOUS
RUN
TRIP
START
SELECT
LANGUAGE
STANDBY
ENGINE
START/RUN
STOP10
Beware of HIGH VOLTAGE (up to 700V) supplied by the
generator as the unit may start automatically. Before servicing unit, make sure the RUN/STOP switch is in STOP position
and disconnect the negative battery cable.
Beware of electric heaters.
Pacemaker holders must stay clear of the unit while operating
as the power generator supplies HIGH VOLTAGE.
Never dis-assemble the generator
HIGH MAGNETIC FIELD INSIDE.
EASY TO
RUN
Standby Operation
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
SETPOINT
=
Connect standby
1
1
cable to unit.
MANUAL
DEFROST
BOX TEMPERATURE
ALARM LIST
!
START-STOP
CONTINUOUS
KEYPAD
RUN
SELECT
LANGUAGE
STANDBY
ENGINE
START/RUN
The microprocessor “LogiCOLD” controls incorporated into
VECTOR are the most reliable control system available.
LogiCOLD is also designed to be the easiest to use.
STOP10
A message center indicates clear instructions and prompts
the driver through each operation. The choice of
8 languages (Danish, Dutch, English, French, German,
Italian, Russian, Spanish) ensures LogiCOLD user-friendly.
Display
Mode lights
To power up the unit, place
2
2
the ENGINE / STANDBY
switch to STANDBY.
3
Place the RUN / STOP switch
3
to RUN to start unit.
Note : The unit is fitted with a phase detector which inhibits engine
start-up if the phases are reversed. In the latter case an alarm sounds.
Place the RUN/STOP switch in the STOP position. Disconnect the power
plug and switch the phases in the socket using a screwdriver.
Message center
Up and Down
arrow key
SETPOINT
=
Enter key
BOX TEMPERATURE
MANUAL
ALARM LIST
DEFROST
Selectable
START-STOPALARMDEFROSTCOOLHEAT
DATAPRETRIP
!
lights
Language switch
CONTINUOUS
RUN
TRIP
FUNCTION
START
CHANGE
SELECT
START-STOP
CONTINUOUS
Run/Stop
LANGUAGE
STANDBY
ENGINE
START/RUN
STOP10
switch
Engine/Standby
switch
LogiCOLD allows minimal input to obtain maximum
output, a true “Set it and forget it” design.
EASY TO
START
EASY TO
RUN
Auto Start / Stop
START-STOPALARMDEFROSTCOOLHEAT
SETPOINT
START/STOP MODE SELECTED
=
Toggle the LANGUAGE switch as soon
2
2
as you select 1 of the 8 available
languages :
English - French - Spanish - German Danish - Dutch - Italian - Russian.
BOX TEMPERATURE
MANUAL
ALARM LIST
DEFROST
!
Place RUN/STOP switch
1
1
in RUN position.
CONTINUOUS
START-STOP
CONTINUOUS
Manual Operation
CONTINUOUS
MANUAL
START-STOPALARMDEFROSTCOOLHEAT
BOX TEMPERATURE
ALARM LIST
!
START-STOP
CONTINUOUS
RUN
SELECT
LANGUAGE
STANDBY
ENGINE
START/RUN
STOP10
RUN
SELECT
LANGUAGE
STANDBY
ENGINE
START/RUN
SETPOINT
STOP10
=
Place the ENGINE/STANDBY switch
1
1
DEFROST
to ENGINE.
Place manual GLOW/CRANK switch (MGC) to
2
2
Glow and hold for 5 to 15 seconds.
While preheating place RUN/STOP switch
3
3
to RUN. “MANUAL START MODE SELECTED”
will appear in message center.
Press the START-STOP/CONTINUOUSkey until
3
3
the START-STOP light on the controller
illuminates.
4
Verify that “START/STOP MODE SELECTED” is
4
displayed on the message center and that the
START-STOP light is illuminated.
4
Place GLOW/CRANK switch in CRANK position
4
to crank and start.
Electrical box
(located inside
unit roadside
front door).
MGC
EASY TO
SELECT
EASY TO
START
Manual Defrost
SETPOINT
DEFROST CYCLE STARTED
=
Press the MANUAL DEFROST key. The
1
1
DEFROST light will come on and the
message center will display “DEFROST
CYCLE STARTED” for 5 seconds or flash
“CANNOT START DEFROST CYCLE” for 5
seconds.
Unit will not defrost if box temperature
is above +4°C.
MANUAL
DEFROST
BOX TEMPERATURE
ALARM LIST
!
Continuous Run
ALARM LIST
!
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
RUN
SELECT
START-STOP
CONTINUOUS
Place RUN/STOP switch
1
1
LANGUAGE
STANDBY
ENGINE
START/RUN
in RUN position.
STOP10
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
START-STOP
CONTINUOUS
RUN
SELECT
LANGUAGE
STANDBY
ENGINE
START/RUN
SETPOINT
CONTINUOUS RUN MODE SELECTED
STOP10
=
Press the START-STOP/CONTINUOUS key
2
2
MANUAL
DEFROST
BOX TEMPERATURE
until the CONTINUOUS RUN light on the
controller illuminates.
Verify that “CONTINUOUS RUN MODE
3
3
SELECTED” is displayed on the message
center and that the CONTINUOUS RUN
light is illuminated.
EASY TO
SET
EASY TO
READ
Temperature Setpoint
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
RUN
SETPOINT
SETPOINT CHANGED
=
1
1
BOX TEMPERATURE
MANUAL
DEFROST
ALARM LIST
!
START-STOP
CONTINUOUS
SELECT
With the message center at the
default display press the UP
ARROW or DOWN ARROW key to
change setpoint to the desired
value.The display will flash to indicate that the setpoint reading
being displayed is a non-entered
value. The message center will
show “ TO SCROLL, THEN = TO
SAVE”.The setpoint display will
flash for 5 seconds if = has not
been pressed.
LANGUAGE
STANDBY
ENGINE
START/RUN
Unit Data
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
RUN
SETPOINT
SUCTION PRESSURE:
STOP10
=
1
1
BOX TEMPERATURE
DATA
MANUAL
DEFROST
ALARM LIST
!
START-STOP
CONTINUOUS
SELECT
Press the SELECT key until DATA is
illuminated.
Press the = key.
2
2
Press the UP or DOWN ARROW key to display the
3
3
next or previous unit data value.
LANGUAGE
STANDBY
ENGINE
START/RUN
STOP10
Press the = (ENTER) key to save the new
2
2
setpoint.
Verify that the message “SETPOINT CHANGED” is
3
3
displayed on the message center.
EASY TO
CHANGE
EASY TO
CHECK
Function Change
START-STOPALARMDEFROSTCOOLHEAT
SETPOINT
PRESS TO VIEW SETTINGS
=
1
Press the SELECT key until FUNCTION
1
CHANGE is highlighted.The message
“PRESS TO VIEW SETTINGS” will appear.
Press the UP or DOWN ARROW to scroll through
2
2
the Function list. ”TO SCROLL THEN = TO
SELECT” will appear.
To change one of the Functions, bring the Function
3
3
you wish to change into the Message Center, and
press = (ENTER) key.“TOSCROLL, THEN = TOSAVE”
will show in the Message Center. Pressing either UPor
DOWN ARROW key will begin to change the Function
setting.The Message Center will flash, indicating that a
change has been made that has not been entered into
memory.
MANUAL
DEFROST
BOX TEMPERATURE
ALARM LIST
!
FUNCTION
CHANGE
START-STOP
CONTINUOUS
CONTINUOUS
RUN
SELECT
LANGUAGE
STANDBY
ENGINE
START/RUN
Pretrip Check
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
RUN
SETPOINT
TEST # 1
STOP10
=
1
1
BOX TEMPERATURE
DATA
MANUAL
DEFROST
ALARM LIST
!
START-STOP
CONTINUOUS
SELECT
Press the SELECT key until PRETRIP
is illuminated.
Press the = key to start PRETRIP.
2
2
Verify that the display shows “TEST # 1”.
3
3
Note : Unit can be off when you start PRETRIP
Press and hold the = key for 5 seconds
will cancel the PRETRIP.
LANGUAGE
STANDBY
ENGINE
START/RUN
STOP10
Continue pressing UP or DOWN ARROW key until the
4
4
desired value is shown, then press the = (ENTER) key.
The Message Center will stop flashing. The new value is
now in memory.
EASY TO
CHECK
EASY TO
SET
Alarm Display / Reset
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
RUN
SETPOINT
NO ACTIVE ALARMS
=
Press the ALARM LIST key. If there are no active
1
1
alarms in the alarm list, the display will say “NO
ACTIVE ALARMS” for 5 seconds.
If there are active alarms in the alarm list, the
2
2
display will be “A” and the alarm message for the
latest active alarm in the list for 5 seconds.
Press the ALARM LIST key to scroll through the list
3
3
of alarms.
When you reach the end of the alarm list, “LIST
4
4
END, = TO CLEAR ALARMS” is displayed.
MANUAL
DEFROST
BOX TEMPERATURE
ALARM LIST
!
START-STOP
CONTINUOUS
SELECT
LANGUAGE
STANDBY
ENGINE
START/RUN
Trip Start
CONTINUOUS
START-STOPALARMDEFROSTCOOLHEAT
RUN
SETPOINT
TRIP START ENTERED
STOP10
=
1
1
BOX TEMPERATURE
TRIP
START
MANUAL
DEFROST
ALARM LIST
!
START-STOP
CONTINUOUS
SELECT
To mark the start of a trip in the data
recorder, press the SELECT key until
TRIP START is lit.
2
Press the = key.
2
If trip start is acknowledged by the data recorder,
3
3
“TRIP START ENTERED” will be displayed for 5
seconds and then the display will revert back to the
normal display.Otherwise “CANNOT ENTER TRIP
START” will flash and then the display will revert
back to the normal display.
LANGUAGE
STANDBY
ENGINE
START/RUN
STOP10
To deactivate the active alarm list, press the = key
5
5
while “LIST END, = TO CLEAR ALARMS” is being
displayed.
Loading...