Carrier split room air conditioner remote control, CS457-R14A, R14E, R14A E, R14C User Manual

...

Download

2020550A6722

Handling the remote controller ......................................................

Remote controller Specifications...................................................

Function buttons .................. .........................................................

Indicators on LCD ..........................................................................

How to use the buttons

Setting the clock ..............................................................................

Recessed button operation ............................................................

Auto operation.................................................................................

Cooling/Heating/Fan operation......................................................

Dehumidifying operation ...............................................................

Adjusting air flow direction............................................................

Timer operation...............................................................................

Sleep operation ..............................................................................

CONTENTS

Use the remote controller within a distance of 8 meters from the appliance, pointing it towards the receiver. Reception is confirmed by a beep.

Location of the remote controller.

CAUTIONS

The air conditioner will not operate if curtains, doors or other materials block the signals from the remote controller to the indoor unit. Prevent any liquid from falling into the remote controller. Do not expose the remote controller to direct sunlight or heat. If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function properly. Use curtains to prevent the sunlight from falling on the receiver. If other electrical appliances react to the remote controller. either move these appliances or consult your local dealer.

The remote controller is powered by two dry batteries(R03/LR03X2) housed in the rear part and protected by a cover. (1) Remove the cover by pressing and sliding off. (2) Remove the old batteries and insert the new batteries,placing the(+) and (-) ends correctly. (3) Reattach the cover by sliding it back into position. NOTE: When the batteries are removed, the remote controller erases all programming. After inserting new batteries, the remote controller must be reprogrammed.

Replacing batteries

Handling the remote controller

Keep the remote controller where its signals can reach the receiver of the unit. When you select the timer operation, the remote controller automatically transmits a signal to the indoor unit at the specified time. If you keep the remote controller in a position that hinders proper signal transmission, a time lag of up to 15 minutes may occur.

M O

FA N S

P EED

T E M

A IR D

I REC

TI ON

S WING

L ED

SLEEP

T URB

CL O

T IME

CANCEL

RESET

F/C

CAUTIONS

Do not mix old and new batteries or batteries of different types. Do not leave the batteries in the remote controller if they are not going to be used for 2 or 3 months. Do not dispose batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

Model

Lowest Voltage of CPU Emitting Signal

Rated Voltage

8m (when using 3.0 voltage, it gets 11m)

3.0V(Dry batteries R03/LR03×2)

2.4V

Remote Controller Specifications

1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only model without), and FAN.

2. Timer Setting Function in 24 hours.

。。

O O

3. Indoor Setting Temperature Range : 17 C~30 C(62 F~88 F).

4. Full function of LCD (Liquid Crystal Display)

Environment

Signal Receiving Range

Performance Feature

Function buttons

Each time the button is pressed, the operation mode is selected in a sequence of following:

MODE Button

3 4

SWING Button Used to stop or start auto swing feature of the louver. Press it again to stop the movement.

ON/OFF Button Operation starts when this button is pressed and stops when this button is pressed again.

NOTE: Heat mode is for Cooling & Heating models only.

AUTO

COOL

DRY

HEAT FAN

Used to select the fan speed in four steps: Auto Low Med High

FAN SPEED Button

R14A/(C)E, RG14A1/(C)E, RG14A2/(C)EF.

Carr ier

AIR DIRECTION Button: Press this button to change the swing angle of louver and set the desired up/down airflow direction. The louver swings for an angle of 6 for each press.

。。

-5 C 60 C( )

O O

23 F~140 F

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

IONI ZER

CANC EL

RESET

F/C

AUT O

AUTO

COO L DRY HEAT FAN

SET TEM P.

CLOCK

TIMER ON

TIMER OFF

SPEED

AUTO LOW MED HIGH

OFF

LED Button

Press this button to clear the digit display in the air conditioner, press it again to activat it. (NOTE:there is no reation to some air conditioners without digital display when you press the LED button.)

RESET Button Once the recessed RESET button is pressed, all of the current settings will be cancelled and the controller will return to the initial settings.

F/C Button

Used to select/display temperature settings in either Celsius or Fahrenheit . Press this button to select either the Celsius or Fahrenheit scale.

But tons: T he se t hre e butto n is dis able fo r model R 14A/( C)E.

TEMP. Button : Push the button to increase the indoor temperature setting or to adjust the TIMER in a clockwise direction. Push the button to decrease the indoor temperature setting or to adjust the TIMER in a counter-clockwise direction.

Mode l: R 14A /E , R14A /C E.

Mode l: R G14 A1 /E, RG14 A1 /CE .

Function buttons(continued)

5 6

The temperature setting (from 17 C(62 F)

to 30 C(88 F)) will be displayed. If FAN mode is selected, there will be no display.

Indicators on LCD

SLEEP Button Select this function during the sleeping time. It can maintain the most comfortable temperature and save energy. This function is available on COOL, HEAT or AUTO mode only .

TIMER Button

Used to initiate the AUTO-ON/AUTO-OFF time program, in conjuction with the & buttons.

Press this button to cancel ON timer and OFF timer.

When push this button, the Ionizer/Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air.

CANCEL Button

IONIZER Button(on some models)

Transmission Indicator

Temp. display

Clock display

Timer display

Lock display

Fan speed display

Sleep Display

Mode display

ON/OFF display

This transmission indicator lights when remote controller transmits signals to the indoor unit.

Displays the current operation mode. Include AUTO, COOL, DRY, HEAT(cooling only type without), FAN ONLY and back to AUTO.

Displayed by pushing the ON/OFF button. Push the ON/OFF button again to disappear.

The current time is indicated.(0 24 hours)

The time set for timer operation is indicated. (0 24 hours)

Displayed by pushing the LOCK button. Push the LOCK button again to disappear.

Displays the selected fan speed, AUTO and three fan speed levels "LOW" "MED" "HIGH" can be indicated. Displays AUTO when the operating mode is either AUTO or DRY.

Display by pushing the SLEEP button. Push the SLEEP Button again to disappear.

In the illustration, all displays are indicated for the sake of clarity. During operation, only the relevant displays will be shown on the remote controller.

NOTE : The TEM P. But to n pr ovides a fu nc ti on that a ll ow y ou t o se t th e LO CK mode . To guard agai ns t ac ci de nt al progra m ch an ge o r un lo ck the re gi st er ed p ro gram, pre ss t he a nd butt on s si mu lt an eously fo r ab ou t 3 se co nd s to alte rn at e be tw ee n LOCK and UN LO CK m od e. Symbol d is pl ay s in di catin g LO CK , th e symb ol d is ap pe ar s indicat in g UN LO CK .

1 2

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

FOLL OW ME

RESET

F/C

AUTO C OOL DRY HEAT FA N

SET TEM P.

CLOCK

TIMER ON

TIMER OFF

SPEED

AUTO LOW MED HIGH

OFF

CLOCK Button: Used to initiate and/or change the time of day setting.

TURBO Button: Push this button on COOL/HEAT(For models adopts PTC or Electrical heater only) mode, the air conditioner goes into powerful cooling/heating operation. Push again to cancel the TURBO function.

AUTO COO L DRY H EAT FA N

SET TE MP.

CLOCK

TIMER ON

TIMER OFF

SPEED

AUTO LOW MED HIGH

FOLLOW ME Display(if applicable)

Displayed when Follow Me function is activated.

Mode l: R G14 A2 /EF, RG14 A2 /CE F.

FOLLOW ME Button(on some models):

Push this button to initiate the Follow Me feature, the remote display is actual temperature at its location. The remote control will send this signal to the air conditioner every 3 minutes interval until press the Follow Me button again. The air conditioner will cancel the Follow Me feature if it does not receive the signal during any 7 minute interval.

Static electricity or other factors (Voltage transients) can cause the remote controller clock to initialise. If your remote controller is initialised (the time of "12:00" flashing), readjust the clock before starting the unit.

CAUTION

Recessed button operation

How to use the buttons

7 8

1. When you press the RESET button, current settings are cancelled and return to original factory settings. In the clock, the time "12:00" will flash, the mode displays "Auto", fan speed displays "Auto", the temperature displays "24". Note: You will need to reprogram the CLOCK setting after pressing the RESET button (Refer to "Setting the CLOCK").

all

2. When you press the F/C button, the temper ature settings on the remote unit can be displayed in either "Celsius" or "Fahrenheit". Press this button to select either Celsius or Fahrenheit scale.

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

AUTO

SET TEM P.

CLOCK

SPEED

AUTO

OFF

Before you start operating the air conditioner, set the clock of the remote controller using the procedures given in this section. The clock panel on the remote controller will display the time regardless of whether the air conditioner is in use or not.

After batteries are inserted in the remote controller, the clock panel will display "12:00" and begin to flash.

1. TEMP.button

Press these buttons to set time. Forward. Backward. Each time you press the button, the time moves forward or backward by one minute depending on which side you press. The time alters as quickly as you push the button. Keep pressing the button without releasing, the time moves forward or backward by 10 minutes depending on which side you press.

Initial Setting or the Clock

When the right time is achieved, press the CLOCK button or release the or and wait for 3 seconds, the clock time stops flashing and the clock starts operating.

Press the CLOCK button on the remote controller for about 3 seconds, the time of the clock display will start to flash. To set the new time, follow 1 and 2 of "Initial Setting of the Clock". Note: The time of the CLOCK must be set before the AUTO-TIMER feature will operate. On TIMER operation, the time of the CLOCK can not be adjusted.

* Clock accuracy is within 15 seconds per day.

3.Readjusting the Clock

CLOCK button

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

AUTO

SET TEM P.

CLOCK

SPEED

AUTO

OFF

Cooling /Heating/Fan operation

Ensu re t he u ni t is p lu gged in and p ow er i s avai la bl e.

1. Pre ss t he M OD E bu tt on t o selec t CO OL , HE AT, (coo li ng & h ea ti ng m odels onl y) o r FAN m od e.

2. Pre ss t he T EM P bu tt on s to set th e de si re d temper at ur e. T he t em pe ra ture can be s et

O O O O

within a r an ge o f 17 C( 62 F) ~ 30 C(88 F) in

O O

1 C /2 F in cr em en ts .

3. Pre ss t he FA N SP EE D bu tt on to sel ec t th e fan spee d in f ou r st ep s- Au to, Low, M ed ,o r Hi gh .

4. Pre ss t he O N/ OF F bu tt on to sta rt t he a ir cond it io ne r.

In the FAN mode, the setting temperature is not displayed in the remote controller and you are not able to control the room temperature either. In this case, only step 1, 3 and 4 may be performed.

NOTE

Dehumidifying operation

Ensu re t he u ni t is p lu gged in and p ow er i s avai la bl e. T he O PE RAT IO N in di ca to r on the disp la y pa ne l of t he i ndoor uni t il lu mi na te s.

1. Pre ss t he M OD E bu tt on t o selec t DRY mod e.

2. Pre ss t he T EM P bu tt on s to set th e de si re d temper at ur e. T he t em pe ra ture can be s et

O O O O

within a r an ge o f 17 C( 62 F) ~ 30 C(88 F) in

O O

1 C /2 F in cr em en ts .

3. Pre ss t he O N/ OF F bu tt on to sta rt t he a ir cond it io ne r.

In the Dehumidifying mode, you can not switch the fan speed. It has already been automatically controlled.

NOTE

Auto operation

Ensu re t he u ni t is p lu gged in and p ow er i s avai la bl e. T he O PE RAT IO N in di ca to r on the disp la y pa ne l of t he i ndoor uni t il lu mi na te s.

1. Pre ss t he M OD E bu tt on t o selec t Aut o.

2. Pre ss t he T EM P bu tt on t o set the d es ir ed temper at ur e. T he t em pe ra ture can be s et

O O O O

within a r an ge o f 17 C( 62 F) ~ 30 C(88 F) in

O O

1 C /2 F in cr em en ts .

3. Pre ss t he O N/ OF Fb ut ton to st ar t th e ai r cond it io ne r.

1. In the Auto mode, the air conditioner can logically choose the mode of Cooling, Fan, Heating and Dehumidifying by sensing the difference between the actual ambient room temperature and the setting temperature on the remote controller.

2. In the Auto mode, you can not switch the fan speed. It has already been automatically controlled.

3. If the Auto mode is not comfortable for you , the desired mode can be selected manually.

NOTE

Adjusting air flow direction

Use the AIR DIRECTION and SWING buttons to adjust the Up/Down airflow direction.

1. When press the AIR DIRECTION button, the

horizontal louver will move at an angle of 6 . Keep pressing the button to move the louver to the desired position.

2. Press the SWING button , the horizontal louver would swing up/down automatically. Press it again to stop.

NOTE: When the louver swing or move to a position which would affect the cooling and heating effect of the air conditioner, it would automatically change the swing/ moving direction.

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

AUTO

SET TEM P.

CLOCK

SPEED

AUTO

OFF

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

COO L

SET TEM P.

CLOCK

SPEED

AUTO

OFF

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

DRY

SET TEM P.

CLOCK

SPEED

AUTO

OFF

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

DRY

SET TEM P.

CLOCK

SPEED

AUTO

OFF

Example of Timer setting

TIMER OFF

Stop

23:00

TIMER ON

Start

Off

6:00

When you select the timer operation, the remote controller automatically transmits the timer signal to the indoor unit at the specified time. Therefore, keep the remote controller in a location from which it can transmit the signal to the indoor unit properly. The effective operation time set by remote controller is limited in 24 hours.

CAUTIONS

1. TIMER button Press the TIMER button as required. The current timer setting is displayed alongside either the TIMER ON or TIMER OFF indicator, and will flash.

2. TEMP. Buttons Press to set the desired time. Forward Backward Each time you push these buttons, the time moves forward or backward by 10 minutes depending on which direction you press. The time alters as quickly as you press the button.

3. After setting the timer for TIMER ON and TIMER OFF, check the TIMER indicator on the display panel of the indoor unit is illuminated.

4. Cancel button(CANCEL) Press the CANCEL button to cancel the timer setting.

Preform steps 1, 2 and 3 to change the settings.

Canceling

Changing

Timer opera tion

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

AUTO

SET TEM P.

SPEED

AUTO

OFF

CLOCK

TIMER ON

TIMER OFF

(Timer Stop Operation) The TIMER OFF feature is useful when you want the unit to turn off automatically after you go to bed. The air conditioner will stop automatically at the set time.

To stop the air conditioner at 23:00 p.m.

1. Press the TIMER button until the TIMER OFF indicator is displayed and the setting time beside is flashing (if the displayed time is just 23:00, 3 seconds later, the TIMER OFF function will be activated automatically).

2. Use the TEMP. button to display "23:00" beside the TIMER OFF indicator.

3. This function will be activated 3 seconds after you release the TEMP. button.

TIMER OFF

Example:

(Timer Start Operation) The TIMER ON feature is useful when you want the unit to turn on automatically before you return home. The air conditioner will automatically start operating at the set time. IMPORTANT: The time will be registered in 3 seconds period (after pressing the TEMP. button), so you should continue pressing the button until the desired time is established. Otherwise you must repeat the steps again.

To start the air conditioner at 6:00 a.m.

1. Press the TIMER button, the TIMER ON indicator is displayed and the setting time beside is flashing(if the displayed time is just 6:00, 3 seconds later, the TIMER ON function will be activated automatically).

2. Use the TEMP/TIME button to display "6:00" beside the TIMER ON indicator of the remote controller.

3. Wait for 3 seconds and the setting time stops flashing and this function is activated.

TIMER ON

Example:

SLEEP operation

When you press the SLEEP button, the energysaving function will be activated. This function enables the unit to automatically

O O

increase(cooling) or decrease(heating) 1 C/2 F per hour for the first two hours, then hold steady for the next 5 hours, after that the unit will stop operation. It can maintain the most comfortable temperature and save energy. NOTE: The SLEEP function is only available under Cooling, Heating and AUTO operations.

Off

Stop

Start

TIMER ON

TIMER OFF

6:00

8:00

Now it is 20:00 o'clock in the evening. You want to stop the air conditioner at 23:00 and start it again at 6:00 in the next morning.

1. Press the TIMER button until the TIMER OFF indicator is displayed and time setting is flashing.

2. Use the TEMP/TIME button to display "23:00" beside the TIMER OFF indicator. Wait 3 seconds, and the AUTO-OFF time will be registered.

3. Press the TIMER button again to display the TIMER ON .

4. Use the TEMP/TIME button to display "6:00" on the TIMER ON display. Wait 3 seconds until the setting time stops flashing and this function is activated.

TIMER OFF → TIMER ON

(On → Stop → Start operation) This feature is useful when you want to stop the air conditioner after you go to bed, and start it again in the morning when you wake up or when you return home.

Example:

COMBINED TIMER

(S both ON and OFF )etting timers simultaneously

Example:

TIMER ON → TIMER OFF

(Off → Start → Stop operation) This feature is useful when you want to start the air conditioner before you wake up and stop it after you leave the house.

To start the air conditioner at 6:00 the next morning, and stop it at 8:00.

1. Press the TIMER button, the TIMER ON indicator is displayed and the setting time is flashing.

2. Use the TEMP/TIME button to display "6:00" beside the TIMER ON indicator of the remote controller. Wait 3 seconds, the AUTO-ON time will be registered.

3. Press the TIMER button again to display the TIMER OFF indicator and the setting time .

4. Use the TEMP/TIME button to display "8:00" beside the TIMER OFF indicator.

5. Wait 3 seconds until the setting time stops flashing and this function is activated.

TIMER OFF

TIMER ON

Stop

23:00

6:00

Start

Carr ier

MODE

FAN SPE ED

TEMP.

AIR DI RECTI ON

SWIN G

LED

SLEE P

TURB O

CLOC K

TIME R

CANC EL

RESET

F/C

COOL

SET TEM P.

CLOCK

SPEED

AUTO

OFF

Carrier split room air conditioner remote control, CS457-R14A, R14E, R14A E, R14C User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual