Warranty Information ....................................................................215
Revision History ................................................................................216
50YEW
196
Carrier : Turn to the Experts.
Carrier Geothermal Heat Pump Systems
50YEW Water-To-Water Design Features
The 50YEW series is unlike any other water-to-water heat pump on
the market today. The large operating map of the scroll compressor
allows high temperature operation, up to 145°F [63°C] leaving
load water temperature even at 32°F [0°C] entering source water
temperature. The combination of a coaxial (tube-in-tube) heat
exchanger for the source (ground loop) side and a brazed plate
heat exchanger for the load (heating/hot water) side provides very
high efciencies. Integral controls for hydronic heating and domestic
water heating avoid the need for external microprocessor-based
controls for outdoor temperature reset, warm weather shutdown,
staging and other controls.
The 50YEW has an extended range refrigeration circuit, capable of
ground loop (geothermal) applications as well as open loop (well
water) applications. Standard features and factory-installed options
are many. Unique application-specic controls make the 50YEW
series ideal for hydronic heating and domestic hot water generation.
The heating-only refrigeration circuit is optimized for high water
temperatures, heating efciencies, and capacities.
The dual level compressor isolation mounting system, insulated
compressor enclosure, and compressor discharge mufer make
the 50YEW series one of the quietest water-to-water heat pumps
available. The attractive “Euro-style” cabinet allows the unit to t into
any decor.
Application Flexibility
• Capacities 10kW [32,600 Btuh].
• High temperature scroll compressor, up to 145°F [63°C] leaving
water temperature.
• Ultra high efciencies (4.2 COP at ground loop conditions; up to
5.5 COP at ground water conditions).
• Built-in programmable controller with Outdoor Temperature Reset
and Warm Weather Shutdown.
• Large, back-lit digital user interface.
• Rugged coaxial (tube-in-tube) “Source” heat exchanger (copper or
cupro-nickel).
• Close approach temperature brazed plate stainless steel “Load”
heat exchanger.
• Dual level compressor isolation, compressor enclosure, and
discharge mufer for Ultra quiet operation.
• “Euro-style” cabinet for attractive look.
• Insulated cabinet with foil backed insulation for ease of cleaning.
• Flush-mount FPT ttings, secured to the cabinet (no backup
wrench required).
• TXV metering device.
• 12-point low voltage terminal strip for ease of installation.
• ETL safety listing.
• Wide variety of options including internally factor y installed
Domestic Hot Water Mode, Load and Source side pumps with
expansion tanks, VSFP (variable speed oor pump connection)
Controls and Cupro-Nickel Source Heat Exchanger.
Service & Installation Advantages
• Hinged front access door and 3 removable panels for ease
of installation and service.
• Galvanized steel construction with protective powder coat paint
and hinged front access door.
• Bi-directional thermal expansion valve.
®
• Puron
• Circuit breaker protected 75VA control transformer.
• High and low pressure service por ts on refrigerant circuit.
• Accurate refrigerant sensing freeze protection.
Factory Quality & Certications
• All units are built on our Integrated Process Control Assembly
a. Veries that the correct components are being assembled.
b. Automatically performs special leak tests on all joints.
c. Conducts pressure tests.
d. Performs highly detailed run test unparalleled in the
HVAC industry.
e. Automatically disables packaging for a “failed” unit.
f. Creates computer database for future service analysis and
• All units are water run-tested in all modes to insure efciency
• Heavy gauge galvanized steel cabinets are epoxy powder coated
• All refrigerant brazing is done in a nitrogen atmosphere.
• All units are deep evacuated to less than 100 microns prior to
• All joints are both helium and halogen leak tested to insure annual
• Coaxial heat exchanger, refrigerant suction lines and all water
• Noise Reduction features include: dual level compressor isolation,
• Safety features include: high pressure and loss of charge to
• 10-year limited warranty on major refrigerant circuit components,
• AHRI/ASHRAE/ANSI/ISO 13256-2 certied.
• NRTL & CSA listed.
• US EPA “Energy Star” compliant.
• ISO 9001:2000 Certied.
Options & Accessories
• Full Condensing Hot Water Generation With Internal Secondar y
• Factory Installed “Load” and “Source” Pumps.
• Factory Installed Expansion Tanks.
• Cupro-Nickel Source Water Coil.
• Extended Labor Allowance and Service Warranty.
HFC-410A zero ozone depletion refrigerant.
System (IPCS). The IPCS is a unique state of the art manufacturing
system that is designed to assure quality of the highest standards of
any manufacturer in the water-source industry. Our IPCS system:
diagnostics from run test results.
and reliability.
for durable and long-lasting nish.
refrigerant charging.
leak rate of less than 1/4 ounce.
lines are fully insulated to eliminate condensation problems in low
temperature applications.
insulated compressor compartment, interior cabinet insulation
using 1/2” coated glass ber, and variable speed fan.
protect the compressor, condensate overow protection, freeze
protection sensors to safeguard the coaxial heat exchanger
and air coil, hot water high-limit and low compressor discharge
temperature switch provided to shut down the hot water
generator when conditions dictate. Fault lockout enables
emergency heat and prevents compressor operation until
thermostat or circuit breaker has been reset.
Optional extended warranties available.
Heat Exchanger and Potable Water Circulating Pump.
Residential Products Technical Guide
50YEW
197
GT-PW Water-to-Water (50YEW) Series
50YEW Water-To-Water Series Features
1
Euro-Style Cabinet For Attractive Look
2
High Temperature Scroll Compressor
3
Rugged Coaxial “Source” Heat Exchanger
Close Approach Temperature Brazed Plate
4
Stainless Steel “Load” Heat Exchanger
Optional Full Condensing Hot Water
5
Generation With Internal Secondary
Heat Exchanger and Potable Water
Circulating Pump
Optional Factory Installed “Load” and
6
“Source” Pumps with expansion tanks
Fully Insulated Water and
7
Refrigerant Lines
6
7
5
11
14
4
1
8
Fully Insulated Compressor Section
Powder Coated Galvanized Steel Cabinet
9
and Front Access Panel For Long Life,
Taupe Metallic
Large Backlight User Interface
10
Built-In Programmable Controller With
11
Outdoor Temperature Reset and Warm
Weather Shutdown
Dual level compressor isolation and discharge
12
mufer for ultra quiet operation
Hinged Front Access Door and Three
13
Removable Panels For Ease of Installation
and Service
12-Point Terminal Strip For Ease of Low
14
Voltage Wiring
3
2
12
9
13
10
50YEW
198
8
Carrier : Turn to the Experts.
Carrier Geothermal Heat Pump Systems
Model Key
5 0A0 1 0CW311
Y E W
Prefix
Residential Series
YEW = Puron High Temperature
Heating Only Water-to-Water
1 2 3
4 5 67
Unit Size
010 (10kW)
Hydronic Options
A = No Pump
B = Load Pump w/Expansion Tank
C = Load Pump & Source Pump(s)
w/Expansion Tanks
8
9101112
Controls
W = CXM
Y = CXM w/VSFP
Packaging
1 = Single Pack, Domestic
Revision Level
1 = Current
Voltage
3 = 208-230/60/1
Water Coil & DHW Options
C = Copper Source & Braze Plate Load, No DHW
D = Copper Source & Braze Plate Load, DHW w/Sec. hx & pump
N = Cupro-Nickel Source & Braze Plate Load, No DHW
P = Cupro-Nickel Source & Braze Plate Load, DHW w/Sec. hx & pump
*When digit 9 = “D” or “P,” digit 7 cannot be A.”
*
*
Residential Products Technical Guide
50YEW
199
GT-PW Water-to-Water (50YEW) Series
Rated Equipment Performance & Efciencies
60 Hz (I-P) Units
Ground Loop Heat PumpGround Water Heat Pump
HeatingHeating
Model
50YEW010
THW01032.64.230.83.342.65.239.94.1
Indoor temperature is also called “Load;” outdoor temperature is also called “Source.” Numbers shown with “/” indicate entering/leaving water temperatures.
Bold outline indicates typical radiant oor application temperatures. Ratings at 40°C [104°F] are based upon AHRI/ISO Standard 13256-2; all other ratings are
based upon Standard EN 14511-2.
Indoor 86/95°F
Outdoor 32/27°F
Capacity
Mbtuh
COP
60 Hz (S-I) Units
Ground Loop Heat PumpGround Water Heat Pump
HeatingHeating
Model
50YEW010
THW0109.574.29.033.312.505.211.694.1
Indoor temperature is also called “Load;” outdoor temperature is also called “Source.” Numbers shown with “/” indicate entering/leaving water temperatures.
Bold outline indicates typical radiant oor application temperatures. Ratings at 40°C [104°F] are based upon AHRI/ISO Standard 13256-2; all other ratings are
based upon Standard EN 14511-2.
Indoor 30/35°C
Outdoor 0/-3°C
Capacity
kW
COP
Indoor 104/113°F
Outdoor 32/27°F
Capacity
Mbtuh
Indoor 40/45°C
Outdoor 0/-3°C
Capacity
kW
COP
COP
Indoor 86/95°F
Outdoor 50/45°F
Capacity
Mbtuh
Indoor 30/35°C
Outdoor 10/7°C
Capacity
kW
COP
COP
Indoor 104/113°F
Outdoor 50/45°F
Capacity
Mbtuh
Indoor 40/45°C
Outdoor 10/7°C
Capacity
kW
COP
COP
50YEW
200
Carrier : Turn to the Experts.
Carrier Geothermal Heat Pump Systems
Performance Data - 50YEW010
SourceLoad
EWT
GPM
°F
208.31.33.1
4.20.30.8
30
8.30.92.0
4.20.30.7
50
8.30.71.7
4.20.30.7
70
8.30.71.7
50YEW operating parameters are as follows: Min Source EWT = 20°F; Max Load LWT = 145°F (see application section for design guidelines).
Interpolation is permissible; extrapolation is not.
Operation below 40°F EWT (source) is based upon 15% methanol antifreeze solution.
All performance data is based upon the lower voltage of dual voltage units.
Antifreeze for source water is required for operation in the shaded area and all source EWTs below 40°F.