Carrier FY4A series, FA4C series Product Data

Page 1

FY4A, FA4C Base Series Fan Coil Sizes 1 1/2 — 5 Ton (018 Thru 060)

Product Data

AIR HANDLER TECHNOLOGY

AT ITS FINEST

The FY4A and FA4C direct--expansion fan coils are designed to cover a wide range of air handling requirements. They are compact and ready to fit where needed, in the basement, crawlspace, attic, utility room, or closet. The unique cabinet design of these fan coils meet new stringent regulations for cabinet air leakage, a requirement of 2% cabinet leakage rate when tested at 1.0 inches of static pressure.

The FY4A and FA4C units are shipped with a factory-- installed hard--shutoff thermostatic expansion valve (TXV) metering device with an internal check valve for reverse flow bi-- pass capability. All units come with solid state fan controls, 1--in. thick insulation with R--value of 4.2, super--quiet multispeed motors, and fully--wettable coils. Units can accommodate factory-- or field--installed heaters from 3 to 30 kW.

The FY4A design is a residential new construction (RNC) model available for use with Puronr, the environmentally sound refrigerant. It comes with or without factory--installed disconnects. It has a pre--painted (gray) galvanized insulated steel casing, 2--speed PSC motor in the 018 through 036 sizes, and 3--speed PSC motors in the 042 through 060 sizes. ArmorCoatt provides a tin plating of the indoor coil’s copper hairpins. This creates a barrier between the corrosion--causing elements and the coil.

The FA4C has all the same quality features as the FY4A, but is for use with R--22 refrigerant.

Page 2

STANDARD FEATURES

S Grooved copper tubing S Lanced sine--wave aluminum fin S Fully--wettable coil S High--impact thermoplastic condensate pan S Primary and secondary drain connections with brass inserts S Multipoise design for maximum versatility S Unique cabinet design that meets new stringent regulations for air leakage. Meets requirements of a 2% cabinet leakage rate when tested

at 1.0 inches of static pressure.

S Field--installed heater packages from 3--30 kW (fused, circuit breaker, or non--fused) S Control board with built--in, replaceable 5-- amp blade--type auto fuse S 2--speed motor in 018 through 036 sizes S 3--speed motor in 042 through 060 sizes S Cooling controls S Time-- delay relay (TDR) S Pre--painted galvanized steel cabinet (gray) S High--density, super thick R--4.2 insulation S Newly--improved filter rack area -- filter door insulation added for an improved air seal S Sweat connections S Inspection plate for cleaning A-- coil design S HUD approved for manufactured housing

FY4A / FA4C

S 40--VA, 208/230v transformer S All models listed with UL (U.S. and Canada) and ARI

ADDITIONAL FEATURES

FY4A

S Puronr refrigerant factory-- installed thermostatic expansion valves (TXV)

S Factory--installed heaters available S ArmorCoatt coil protection available

FA4C

S R--22 refrigerant factory--installed thermostatic expansion valves (TXV) S 018--060 sizes available with or without factory--installed disconnect S Factory--installed heaters available

Page 3

MODEL NUMBER NOMENCLATURE

1 2 3 4 5 6 7 --- 9 1 0 --- 1 2

F A 4 C N F 018 000

Product Type Position Series Electrical

F --- F a n C o i l A --- B a se , R --- 2 2

Y --- B as e , P u r o n r Refrigerant

the environmentally sound refrigerant

4 --- Multipoise C N --- 208/230v,

CERTIFICATION APPLIES ONLY WHEN THE COMPLETE SYSTEM IS LISTED WITH ARI

1ph---60Hz

Cabinet/

Insulation

B --- M o du l ar C --- Fa c t or y

Disconnects

F --- S in g l e pi e c e

Capacity Heating

018 --- 18,000 024 --- 24,000 030 --- 30,000 036 --- 36,000 042 --- 42,000 048 --- 48,000 060 --- 60,000

T 0 0 --- A r mo r Co a t t 000 --- No Heat 005 --- 5kW 008 --- 8kW 010 --- 10kW 015 --- 15kW

ISO 9001:2000

REGISTERED

Size

FY4A / FA4C

Page 4

A05355

FY4A / FA4C

DIMENSIONS

036 Puron - 3/4" I.D.SWEAT

036 R-22 - 7/8" I.D.SWEAT

042 - 060 - 7/8"I.D.SWEAT

LIQUID: 3/8" I.D. SWEAT

CONDENSATE: 3/4" FPT

A B C D E H† J

in mm in mm in mm in mm in mm in mm in mm

COIL

TYPE

018 Slope 42---11/16 1084 14---5/16 364 12--- 7/16 316 12 --- 5/16 313 10 ---7/16 265 — — 12 305

036 Slope 53 ---7/16 1357 21 ---1/8 537 19 --- 1/4 489 19 --- 1/8 486 19 --- 3/16 487 — — 19 483

042 A 49---5/8 1260.5 21---1/8 537 19---1/4 489 19 ---1/8 486 15 ---3/8 391 — — — —

048 A 53 ---7/16 1357 21 --- 1/8 537 19 ---1/4 489 19 --- 1/8 486 19---1/2 495 — — — —

UNIT

SIZE

FY, FA

024, 030 Slope 47---11/16 1211.5 17--- 5/8 448 15 --- 3/4 400 15 ---5/8 397 15 ---3/8 391 — — 17 432

060 A 59---3/16 1503 24 --- 11/16 627 22 ---3/4 577 22---11/16 576 25---1/4 642 34 ---1/16 685 — —

† Applicable to modular units only.

Page 5

A05356

FY4A / FA4C

F G

DIMENSIONS (CONT)

COIL TYPE

UNIT SIZE

in mm in mm

FY, FA

018 Slope 18 ---1/8 460 18---5/8 473

024, 030 Slope 23 --- 1/8 587 23--- 5/8 600

036 Slope 26---15/16 684 27---1/2 699

042 A 23 --- 7/16 593 23--- 1/8 587

048 A 27---1/4 692 2 6 --- 1 5 / 16 684

060 A 32---15/16 837 32---5/8 829

Page 6

FACTORY

(

kW)

(

)

ODS CATALOG

ORDERING NO.

FY4ANF018(T,0)00 ---

FY4ANF018005 5 FY4ANF018008 8

FY4ANF024(T,0)00 ---

FY4ANF024005 5 FY4ANF024010 10

FY4ANF030(T,0)00 ---

FY4ANF030008 8 FY4ANF030010 10

FY4ANF036(T,0)00 ---

FY4ANF036010 10 FY4ANF036015 15

FY4ANF042(T,0)00 ---

FY4ANF042010 10 FY4ANF042015 15

FY4ANF048(T,0)00 ---

FY4A / FA4C

6th digit: B --- M o du l ar c a bi n e t, C --- D is c o nn e ct , F --- S in gl e p ie ce c a bi n e t 10th digit: 0 --- St a nd a r d c o p p er c o il , T --- A rm o r C o a tt

FY4ANF048010 10 FY4ANF048015 15

FY4ANB060(T,0)00 ---

FY4ANB060010 10 FY4ANB060015 15

INSTALLED

HEAT

(kW)

PHYSICAL DATA

NOMINAL COOLING

CAPACITY

(BTUH)

18,000

24,000

30,000

36,000

42,000

48,000

60,000

Height Width Depth

42--- 11/16”

1084mm

47--- 11/16”

1211mm

47--- 11/16”

1211mm

53--- 7/16”

1357mm

49--- 5/8”

1260mm

53--- 7/16”

1357mm

59--- 3/16”

1503mm

DIMENSIONS

14--- 5/16”

363mm

17--- 5/8”

447mm

17--- 5/8”

447mm

21--- 1/8”

536mm

21--- 1/8”

536mm

21--- 1/8”

536mm

24--- 11/16”

627mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

SHIPPING

WEIGHT

100 lb

45 kg

117 lb

53 kg

120 lb

54 kg

144 lb

65 kg

150 lb

68 kg

170 lb

77 kg

198 lb

90 kg

ODS CATALOG

ORDERING NO.

FA4CNF018000 --FA4CNF018005 FA4CNC018005 FA4CNF018008 8 FA4CNF024000 --FA4CNF024005 FA4CNC024005 FA4CNF024010 10 FA4CNF030000 --FA4CNF030008 FA4CNC030008 FA4CNF030010 10 FA4CNF036000 --FA4CNF036010 FA4CNC036010 FA4CNF036015 15 FA4CNF042000 --FA4CNF042010 FA4CNC042010 FA4CNF042015 15 FA4CNF048000 --FA4CNF048010 FA4CNC048010 FA4CNF048015 15 FA4CNB060000 --FA4CNB060010 FA4CNC060010 FA4CNB060015 15

6th digit: B --- M o du l ar c a bi n e t, C --- D is c o nn e ct , F --- S in gl e p ie ce c a bi n e t

FACTORY

INSTALLED

HEAT

NOMINAL COOLING

CAPACITY

BTUH

18,000

24,000

30,000

36,000

42,000

48,000

60,000

DIMENSIONS

Height Width Depth

42--- 11/16”

1084mm

47--- 11/16”

1211mm

47--- 11/16”

1211mm

53--- 7/16”

1357mm

49--- 5/8”

1260mm

53--- 7/16”

1357mm

59--- 3/16”

1503mm

14--- 5/16”

363mm

17--- 5/8”

447mm

17--- 5/8”

447mm

21--- 1/8”

536mm

21--- 1/8”

536mm

21--- 1/8”

536mm

24--- 11/16”

627mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

22--- 1/16”

560mm

SHIPPING

WEIGHT

100 lb

45 kg

117 lb

53 kg

120 lb

54 kg

144 lb

65 kg

150 lb

68 kg

170 lb

77 kg

198 lb

90 kg

Page 7

SPECIFICATIONS

MODEL FY4A 018 024 030 036 042 048 060

COIL

Puronr Refrigerant Metering Device

TXV Size 2ton 3ton 4ton Rows/Fins Per In. 3 / 14.5 Face Area (Sq. Ft.) 2.23 2.97 3.46 4.45 5.93 7.42 Configuration Slope A

FAN

CFM (Nominal) 600 800 1000 1200 1400 1600 2000 Motor Type PSC PSC PSC PSC PSC PSC PSC Motor Hp 1/6 1/4 1/4 1/3 1/2 3/4 3/4

FILTER*

21---1/2” / 546 mm X 13” / 330 mm 16 ---3/8” / 417 mm 19 ---7/8” / 505 mm 23---5/16” / 585 mm

CABINET CONFIGURATION OPTIONS

1 --- p i e c e 1 --- pi e c e 1 --- p i e ce 1 --- p i e c e 1 --- pi e c e 1 --- pi e c e Modular

*Filter must be field ---supplied for FY4A units.

MODEL FA4C 018 024 030 036 042 048 060

R --- 2 2 R e fr i ge r a n t Metering Device

TXV SIZE 3ton 5ton 6ton

COIL

Rows/Fins Per In. 3 / 14.5 Face Area (Sq. Ft.) 2.23 2.97 3.46 4.45 5.93 7.42 Configuration Slope A

FAN

CFM (Nominal) 600 800 1000 1200 1400 1600 2000 Motor Type PSC PSC PSC PSC PSC PSC PSC Motor Hp 1/6 1/4 1/4 1/3 1/2 3/4 3/4

FILTER*

21---1/2” / 546 mm X 13” / 330 mm 16 --- 3/8” / 417 mm 19 --- 7/8” / 505 mm 23---5/16” / 585 mm

CABINET CONFIGURATION OPTIONS

1 --- p i e c e 1 --- pi e c e 1 --- p i e c e 1 --- p i e ce 1 --- pi e c e 1 --- pi e c e Modular

*Filter must be field ---supplied for FA4C units.

T X V --- f a c t o r y i n st a l l ed h a r d --- s h u to f f, b i --- f l o w ty p e f o r he a t p u m p a pp l ic a t i o n

PERFORMANCE DATA

AIRFLOW PERFORMANCE (CFM)

MODEL & SIZE

FY4A, FA4C

018

FY4A, FA4C

024

FY4A, FA4C

030

FY4A, FA4C

036

FY4A, FA4C

042

FY4A, FA4C

048

FY4A, FA4C

060

--- S h a d in g --- A i r f l o w o u t si d e 4 50 c f m/ t o n .

NOTES:

1. Airflow based upon dry coil at 230v with factory --- approved filter and electric heater (2 element heater sizes 18 thru 36, 3 element heater sizes 42 thru 60). Airflow at 208 volts is approximately 10% lower.

2. To avoid potential f or condensate blowing out of drain pan prior to making drain trap: Return static pressure must be less than 0.40 in. wc. Horizontal applications of 042 --- 060 sizes must have supply static greater than 0.20 in. wc.

3. Airflow above 400 cfm/ton on 048---060 size could result in condensate blowing off coil or splashing out of drain pan.

BLOWER

SPEED

0.10 0.20 0.30 0.40 0.50 0.60

High 816 795 753 690 607 504

Low 633 620 588 538 468 380

High 1055 991 926 860 793 724

Low 934 878 818 754 686 614

High 1070 1032 978 908 822 721

Low 910 888 849 791 715 621

High 1352 1316 1273 1223 1167 1103

Low 1137 1112 1081 1043 998 946

High 1720 1668 1602 1521 1426 1316

Medium 1576 1540 1488 1421 1338 1239

Low 1388 1367 1330 1278 1209 1124

High 1902 1824 1743 1659 1571 1479

Medium 1830 1763 1690 1611 1527 1436

Low 1625 1584 1531 1465 1387 1296

High 2128 2050 1965 1875 1778 1674

Medium 1959 1898 1829 1750 1663 1566

Low 1748 1709 1659 1598 1525 1442

TOTALEXTERNALSTATICPRESSURE

FY4A / FA4C

Page 8

PERFORMANCE DATA (cont)

GROSS COOLING CAPACITIES (mbh) -- PURONR REFRIGERANT

UNIT SIZE

FY4A

018

FY4A

024

FY4A / FA4C

FY4A

030

FY4A

036

FY4A

042

FY4A

048

FY4A

060

See Notes fol l owing table.

INDOOR COIL

AIR

CFM EWB TC SHC BF TC SHC BF TC SHC BF TC SHC BF TC SHC BF

1000

1125

1050

1200

1350

1225

1400

1575

1400

1600

1800

1600

1750

2000

72 / 22 40 20 0.00 36 18 0.00 32 16 0.00 27 14 0.02 21 11 0.02 67 / 19 33 20 0.02 29 18 0.02 24 16 0.03 20 14 0.03 14 12 0.03

525

62 / 17 26 21 0.03 22 18 0.03 18 16 0.03 14 14 0.08 12 12 0.22 72 / 22 44 22 0.00 40 20 0.00 35 17 0.01 30 15 0.02 24 13 0.03 67 / 19 36 22 0.03 32 20 0.03 27 18 0.03 22 15 0.04 16 13 0.04

600

62 / 17 29 23 0.04 25 21 0.04 20 18 0.04 16 16 0.10 13 13 0.24 72 / 22 48 24 0.00 43 22 0.00 38 19 0.02 32 17 0.03 26 14 0.04 67 / 19 40 25 0.04 35 22 0.04 29 20 0.04 24 17 0.04 17 14 0.05

675

62 / 17 32 25 0.05 27 23 0.05 22 20 0.05 17 17 0.11 15 15 0.26 72 / 22 51 25 0.00 46 23 0.00 40 20 0.02 34 17 0.03 27 15 0.03 67 / 19 42 26 0.04 37 23 0.04 31 20 0.04 25 18 0.04 18 15 0.04

700

62 / 17 34 26 0.04 28 24 0.04 23 21 0.05 18 18 0.10 15 15 0.25 72 / 22 56 28 0.00 51 25 0.00 44 22 0.03 37 19 0.04 30 16 0.05 67 / 19 46 29 0.05 40 26 0.05 34 23 0.05 27 20 0.05 20 17 0.06

800

62 / 17 37 29 0.06 31 26 0.06 25 23 0.06 20 20 0.13 17 17 0.27 72 / 22 61 30 0.00 55 27 0.01 48 24 0.04 40 21 0.05 32 18 0.06 67 / 19 50 31 0.06 44 28 0.06 37 25 0.06 29 21 0.06 21 18 0.07

900

62 / 17 40 32 0.07 34 29 0.07 27 25 0.07 22 22 0.15 18 18 0.29 72 / 22 61 30 0.01 55 27 0.00 48 24 0.02 41 21 0.03 33 18 0.03 67 / 19 50 31 0.04 44 28 0.04 37 25 0.04 30 21 0.04 22 18 0.05

875

62 / 17 41 32 0.04 34 29 0.04 28 25 0.05 22 22 0.11 18 18 0.25 72 / 22 68 33 0.00 61 30 0.00 53 27 0.03 45 23 0.04 36 19 0.05 67 / 19 56 34 0.05 49 31 0.05 41 27 0.05 33 24 0.05 24 20 0.06 62 / 17 45 35 0.06 38 32 0.06 30 28 0.06 24 24 0.13 20 20 0.27 72 / 22 73 36 0.00 66 33 0.02 58 29 0.04 48 25 0.05 39 21 0.06 67 / 19 60 38 0.06 53 34 0.06 45 30 0.06 36 26 0.06 26 22 0.07 62 / 17 49 39 0.07 41 35 0.07 33 31 0.08 27 27 0.16 23 23 0.29 72 / 22 79 39 0.00 71 35 0.00 62 31 0.02 52 27 0.03 42 23 0.04 67 / 19 65 40 0.04 57 36 0.04 48 32 0.04 38 28 0.04 28 23 0.05 62 / 17 52 41 0.05 44 37 0.05 36 33 0.05 28 28 0.11 24 24 0.26 72 / 22 87 43 0.00 78 39 0.00 68 34 0.03 57 30 0.04 46 25 0.05 67 / 19 72 44 0.05 63 40 0.05 53 35 0.06 42 31 0.06 31 26 0.06 62 / 17 58 46 0.06 49 41 0.06 39 36 0.07 31 31 0.14 26 26 0.28 72 / 22 95 47 0.00 85 42 0.02 74 37 0.05 62 32 0.06 50 28 0.06 67 / 19 78 49 0.06 68 44 0.06 57 39 0.07 46 34 0.07 33 29 0.07 62 / 17 63 50 0.07 53 45 0.07 43 40 0.08 35 35 0.16 29 29 0.30 72 / 22 93 46 0.00 83 41 0.00 73 37 0.01 62 32 0.03 49 27 0.03 67 / 19 76 47 0.03 67 42 0.03 57 37 0.04 45 32 0.04 33 27 0.04 62 / 17 61 48 0.04 52 43 0.04 42 38 0.04 33 33 0.10 28 28 0.24 72 / 22 102 51 0.00 92 46 0.00 80 40 0.02 68 35 0.04 54 30 0.04 67 / 19 84 52 0.04 74 47 0.04 62 42 0.05 50 36 0.05 36 31 0.05 62 / 17 68 53 0.05 57 48 0.05 46 43 0.06 37 37 0.12 31 31 0.26 72 / 22 111 55 0.00 100 50 0.01 87 44 0.04 74 38 0.05 59 32 0.05 67 / 19 92 57 0.05 80 51 0.06 68 46 0.06 54 40 0.06 39 34 0.06 62 / 17 74 59 0.06 62 53 0.06 50 47 0.07 41 41 0.14 34 34 0.28 72 / 22 109 54 0.00 98 49 0.00 86 43 0.00 73 37 0.02 58 31 0.02 67 / 19 90 55 0.02 79 49 0.02 67 44 0.03 53 38 0.03 39 32 0.03 62 / 17 72 56 0.03 61 50 0.03 49 44 0.03 38 38 0.08 32 32 0.22 72 / 22 121 60 0.00 109 54 0.00 95 48 0.01 81 41 0.02 65 35 0.03 67 / 19 100 61 0.03 87 55 0.03 74 49 0.03 59 42 0.04 43 36 0.04 62 / 17 80 63 0.04 68 56 0.04 55 50 0.04 43 43 0.10 36 36 0.24 72 / 22 132 65 0.00 119 59 0.00 104 52 0.02 88 45 0.03 70 38 0.04 67 / 19 109 67 0.04 95 61 0.04 81 54 0.04 64 47 0.04 47 39 0.05 62 / 17 88 69 0.05 74 62 0.05 60 55 0.05 48 48 0.11 40 40 0.26 72 / 22 132 65 0.00 119 59 0.00 104 52 0.00 89 45 0.01 71 38 0.02 67 / 19 108 67 0.02 95 60 0.02 81 53 0.02 65 46 0.02 48 39 0.02 62 / 17 87 68 0.02 74 61 0.02 60 54 0.03 47 47 0.06 39 39 0.21 72 / 22 141 70 0.00 127 63 0.00 112 56 0.00 95 48 0.02 76 41 0.02 67 / 19 116 72 0.02 102 64 0.02 87 57 0.03 70 49 0.03 51 42 0.03 62 / 17 94 73 0.03 80 66 0.03 64 58 0.03 50 50 0.08 42 42 0.22 72 / 22 156 77 0.01 141 70 0.00 124 62 0.01 105 54 0.02 84 46 0.03 67 / 19 129 80 0.03 113 72 0.03 96 64 0.03 77 55 0.04 57 47 0.04 62 / 17 104 82 0.04 88 73 0.04 71 65 0.04 57 57 0.10 48 48 0.24

35 / 2 40 / 4 45 / 7 50 / 10 55 / 13

SATURATED TEMPERATURE LEAVING EVAPORATOR (_F/°C)

Page 9

PERFORMANCE DATA (cont)

GROSS COOLING CAPACITIES (mbh) -- R--22

UNIT SIZE

FA4C

018

FA4C

024

FA4C

030

FA4C

036

FA4C

042

FA4C

048

FA4C

060

See Notes fol l owing table.

INDOOR COIL

AIR

CFM EWB TC SHC BF TC SHC BF TC SHC BF TC SHC BF TC SHC BF

1000

1125

1050

1200

1350

1225

1400

1575

1400

1600

1800

1600

1750

2000

72 / 22 38 19 0.00 35 17 0.00 30 15 0.01 26 13 0.02 21 11 0.02 67 / 19 32 20 0.02 28 18 0.02 24 16 0.03 19 14 0.03 13 12 0.03

525

62 / 17 26 20 0.03 22 18 0.03 18 16 0.04 14 14 0.11 12 12 0.26 72 / 22 42 21 0.00 38 19 0.00 33 17 0.02 28 15 0.02 23 13 0.03 67 / 19 35 22 0.03 30 20 0.03 26 18 0.03 21 15 0.03 15 13 0.04

600

62 / 17 28 22 0.04 24 20 0.04 19 18 0.05 16 16 0.13 13 13 0.28 72 / 22 45 22 0.00 41 20 0.02 36 18 0.03 30 16 0.03 24 14 0.04 67 / 19 37 24 0.04 33 21 0.04 28 19 0.04 22 17 0.04 16 14 0.05

675

62 / 17 30 25 0.05 26 22 0.05 21 20 0.06 17 17 0.15 14 14 0.30 72 / 22 49 24 0.00 44 22 0.00 38 19 0.02 32 17 0.03 26 14 0.03 67 / 19 40 25 0.04 35 23 0.04 30 20 0.04 23 17 0.04 16 14 0.05

700

62 / 17 32 26 0.04 27 23 0.04 22 21 0.05 18 18 0.14 15 15 0.29 72 / 22 53 26 0.00 48 24 0.02 42 21 0.04 35 18 0.04 28 16 0.05 67 / 19 44 27 0.05 38 25 0.05 32 22 0.05 26 19 0.05 18 16 0.06

800

62 / 17 35 29 0.05 30 26 0.06 24 23 0.07 20 20 0.17 16 16 0.31 72 / 22 57 28 0.00 51 26 0.03 45 23 0.05 38 20 0.05 30 17 0.06 67 / 19 47 30 0.06 41 27 0.06 35 24 0.06 28 21 0.06 20 18 0.08

900

62 / 17 38 31 0.07 32 28 0.07 26 25 0.08 22 22 0.19 18 18 0.33 72 / 22 62 30 0.00 55 27 0.01 48 24 0.02 41 21 0.03 32 18 0.04 67 / 19 51 32 0.04 44 28 0.04 37 25 0.04 29 22 0.04 20 18 0.05

875

62 / 17 41 33 0.04 34 29 0.05 27 26 0.06 22 22 0.15 18 18 0.30 72 / 22 67 33 0.00 60 30 0.02 52 27 0.04 44 23 0.04 35 20 0.05 67 / 19 55 35 0.05 48 31 0.05 41 28 0.05 32 24 0.05 22 20 0.07 62 / 17 44 36 0.06 38 33 0.06 30 29 0.07 25 25 0.18 20 20 0.32 72 / 22 72 36 0.01 65 32 0.04 57 29 0.05 47 25 0.05 38 22 0.06 67 / 19 60 38 0.06 52 34 0.06 44 30 0.06 35 27 0.07 24 22 0.08 62 / 17 48 39 0.07 41 36 0.07 33 32 0.09 27 27 0.20 23 23 0.34 72 / 22 72 36 0.00 65 32 0.01 57 29 0.03 48 25 0.03 38 21 0.04 67 / 19 59 37 0.04 52 34 0.04 44 30 0.04 34 26 0.04 24 21 0.06 62 / 17 48 39 0.05 40 35 0.05 32 31 0.06 26 26 0.16 22 22 0.31 72 / 22 79 39 0.00 71 35 0.03 62 31 0.04 52 27 0.05 41 23 0.05 67 / 19 65 41 0.05 57 37 0.05 48 33 0.06 38 29 0.06 26 24 0.07 62 / 17 52 43 0.06 44 39 0.06 36 34 0.08 29 29 0.18 24 24 0.33 72 / 22 85 42 0.01 76 38 0.04 66 34 0.05 56 30 0.06 45 25 0.06 67 / 19 70 45 0.06 61 40 0.06 51 36 0.07 41 31 0.07 29 26 0.09 62 / 17 56 46 0.07 48 42 0.07 39 38 0.09 32 32 0.20 27 27 0.34 72 / 22 85 42 0.00 77 38 0.01 67 34 0.02 57 30 0.03 46 25 0.03 67 / 19 70 44 0.03 62 40 0.03 52 36 0.04 42 31 0.04 30 26 0.04 62 / 17 57 46 0.04 48 42 0.04 39 37 0.05 32 32 0.14 27 27 0.28 72 / 22 92 46 0.00 83 42 0.02 73 37 0.03 62 33 0.04 50 28 0.04 67 / 19 76 48 0.04 67 44 0.04 57 39 0.05 46 35 0.05 33 29 0.06 62 / 17 62 51 0.05 53 46 0.05 43 41 0.06 36 36 0.16 30 30 0.30 72 / 22 99 49 0.01 89 45 0.03 79 40 0.04 67 36 0.05 53 30 0.05 67 / 19 82 52 0.05 72 48 0.05 61 43 0.06 49 38 0.06 36 32 0.07 62 / 17 67 55 0.06 57 50 0.06 47 45 0.08 39 39 0.18 33 33 0.32 72 / 22 89 44 0.00 81 40 0.00 72 36 0.01 61 32 0.02 50 28 0.02 67 / 19 74 47 0.02 66 43 0.02 56 38 0.03 46 34 0.03 34 29 0.03 62 / 17 60 49 0.03 52 45 0.03 43 40 0.04 35 35 0.11 29 29 0.26 72 / 22 96 48 0.00 87 44 0.01 78 40 0.02 67 35 0.03 54 30 0.03 67 / 19 80 51 0.03 71 47 0.03 61 42 0.03 50 37 0.03 37 32 0.04 62 / 17 65 54 0.04 56 49 0.04 47 45 0.05 39 39 0.14 33 33 0.28 72 / 22 103 51 0.01 94 47 0.02 83 43 0.03 72 38 0.03 58 33 0.04 67 / 19 86 55 0.04 76 51 0.04 66 46 0.04 53 41 0.04 40 36 0.05 62 / 17 70 59 0.04 60 54 0.05 50 49 0.06 43 43 0.16 36 36 0.29 72 / 22 118 58 0.00 107 53 0.00 94 48 0.01 81 42 0.01 66 36 0.01 67 / 19 98 61 0.02 86 55 0.02 74 50 0.02 60 44 0.02 43 37 0.03 62 / 17 79 63 0.02 68 58 0.02 55 52 0.03 45 45 0.10 37 37 0.25 72 / 22 125 62 0.00 113 56 0.00 100 51 0.01 86 45 0.02 69 38 0.02 67 / 19 103 65 0.02 92 59 0.02 78 53 0.03 64 47 0.03 46 40 0.03 62 / 17 84 68 0.03 72 62 0.03 59 56 0.04 48 48 0.11 40 40 0.26 72 / 22 135 67 0.00 123 62 0.01 109 56 0.02 93 49 0.03 76 42 0.03 67 / 19 113 71 0.03 100 65 0.03 85 59 0.03 69 52 0.03 51 45 0.04 62 / 17 92 75 0.04 79 69 0.04 65 62 0.05 54 54 0.13 45 45 0.27

35 / 2 40 / 4 45 / 7 50 / 10 55 / 13

SATURATED TEMPERATURE LEAVING EVAPORATOR (_F/°C)

FY4A / FA4C

Page 10

PERFORMANCE DATA (cont)

NOTES:

CFM -- Cubic Ft. per Minute

SHC -- Gross Sensible Capacity 1000 Btuh BF -- Bypass Factor MBH -- 1000 Btuh

1. Contact manufacturer for cooling capacities at conditions other than shownintable.

2. Formulas: Leaving db

Leaving wb = wb corresponding to enthalpy of air leaving coil (h h

lwb=hewb

where h permissible. Do not extrapolate.

3. SHC is based on 80_F db temperature of air entering coil. Below 80_F db, subtract (Correction Factor x CFM) from SHC. Above 80_F db, add (Correction Factor x CFM) to SHC.

4. Bypass Factor = 0 indicates no psychometric solution. Use bypass factor of next lower EWB for approximation.

Interpolation is permissible. Correction Factor = 1.09 x (1 --- BF) x (db --- 80)

= entering db ---sensible heat cap.

---total capacity (Btuh)

4.5 x CFM

= enthalpy of air entering coil. Direct interpolation is

ewb

EWB -- Entering Wet Bulb (_F) LWB -- Leaving Wet Bulb (_F)

1.09 x CFM

lwb

)

MINIMUM CFM AND MOTOR SPEED SELECTION

FAN COIL SIZES

FY4A / FA4C

FY, FA

3 5 8 9 10 15 18 20 24 30

018 525 525 525 — 600* — — — — — 024 700 700 700 — 700 775* — — — — 030 — 875 875 — 875 875 — 1060* — — 036 — 1050 970 970 970 920 — 1040 — — 042 — — 1225 1225 1225 1225 1225 1225 — — 048 — — 1400 1400 1400 1400 1400 1400 1400 1400 060 — — 1750 1750 1750 1750 1750 1750 1750 1750

*Indicates medium speed (blue). All other motor speeds at low tap.

TC -- Gross Cooling Capacity 1000 Btuh

SHC CORRECTION FACTOR

ENTERING AIR DRY-- BULB TEMPERATURE (_F)

BYPASS

FACTOR

0.10 .098 1.96 2.94 3.92 4.91 Use

0.20 0.87 1.74 2.62 3.49 4.36

0.30 0.76 1.53 2.29 3.05 3.82

HEATER kW

79 78 77 76 75 Under 75

81 82 83 84 85 Over 85

Correction Factor

formula

shown

below

AIR DELIVERY PERFORMANCE CORRECTION COMPONENT PRESSURE DROP (in. wc) AT INDICATED AIRFLOW (DRY--TO--WET COIL)

FY, FA

SIZE

500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000

018 0.034 0.049 0.063 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --024 0.016 0.027 0.038 0.049 0.059 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --030 --- --- --- --- --- --- 0.049 0.059 0.070 0.080 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --036 --- --- --- --- --- --- --- --- --- --- 0.055 0.064 0.073 0.081 --- --- --- --- --- --- --- --- --- --- --- --- --- --042 --- --- --- --- --- --- --- --- --- --- --- --- --- --- 0.049 0.056 0.063 0.070 --- --- --- --- --- --- --- --- --- --048 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- 0.038 0.043 0.049 0.054 0.059 --- --- --- --060 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- 0.027 0.031 0.035 0.039 0.043

CFM

FIELD--INSTALLED ACCESSORY FILTER STATIC PRESSURE DROP (in. wc)

UNIT SIZE

FY, FA

400 600 800 1000 1200 1400 1600 1800 2000

018 0.020 0.044 0.075 --- --- --- --- --- ---

024, 030 --- 0.022 0.048 0.072 0.100 --- --- --- ---

036, 042, 048 --- --- --- 0.051 0.070 0.092 0.120 0.152 ---

060 --- --- --- --- --- --- 0.086 0.105 0.130

CFM

ELECTRIC HEA TER STATIC PRESSURE DROP (in. wc)

018 --- 036 042 --- 060

HEATER

ELEMENTS

EXTERNAL STATIC

PRESSURE

CORRECTION

HEATER

ELEMENTS

0 0 +.02 0 0 +.04 1 3, 5 +.01 2 8, 10 +.02 2 8, 10 0 3 9, 15 0 3 9, 15 –.02 4 20 –.02 4 20 –.04 6 18, 24, 30 –.10

The airflow performance data was developed using fan coils with 10---kW electric heaters (2 elements) in the 018 through 036 size units and 15---kW heaters (3 elements) in the 042 through 060 size units. For fan coils with heaters of a different number of elements, the external available static at a given CFM from the curve may be corrected by adding or subtracting available external static pressure as indicated above.

EXTERNAL STATIC

PRESSURE

CORRECTION

Page 11

PERFORMANCE DATA (cont)

ACCESSORY ELECTRIC HEATERS

HEATER

PAR T NO.

kW @

240V

VOLTS/

STAGES (kW OPERATING)

KFCEH0401N03 3 230/1 3 None 018–024 9,400 KFCEH0501N05 5 230/1 5 None 018–060 15,700 KFCEH0801N08 8 230/1 8 None 018–060 25,100 KFCEH0901N10 10 230/1 10 None 018–060 31,400

KFCEH3201F20 20 230/1 5, 20 Fuse} 030–060 62,800 KFCEH1601315 15 230/3 5, 15 None 036–060 47,100 KFCEH2001318 18 230/3 6, 12, 18 None 042–060 56,500 KFCEH3401F24 24 230/3* 8, 16, 24 Fuse 048, 060 78,300

KFCEH3501F30 30 230/3* 10, 20, 30 Fuse 048, 060 94,100 KFCEH2401C05 5 230/1 5 Circuit Breaker 018–060 15,700 KFCEH2501C08 8 230/1 8 Circuit Breaker 018–060 25,100 KFCEH2601C10 10 230/1 10 Circuit Breaker 018–060 31,400 KFCEH3301C20 20 230/1 5, 20 Circuit Breaker 030–060 62,800 KFCEH2901N09 9 230/1{ 3, 9 None 036–060 28,200

KFCEH3001F15 15 230/1 5, 15 Fuse} 024–060 47,100 KFCEH3101C15 15 230/1 5, 15 Circuit Breaker 024–060 47,100

* Field convertible to 1 phase.

{ Fieldconvertibleto3phase. } Single point wiring kit required for these heaters in Canada.

** Blower motor heat not included.

INTERNAL

CIRCUIT

PROTECTION

FAN COIL SIZE

USED WITH

HEATING CAP.**

@ 230V

FY4A / FA4C

ESTIMATED SOUND POWER LEVEL (dBA)

UNIT SIZE

FY, FA

018 600 0.25 64.7 60.7 56.7 53.7 51.7 49.7 45.7 024 800 0.25 66.0 62.0 58.0 55.0 53.0 51.0 47.0 030 1000 0.25 67.0 63.0 59.0 56.0 54.0 52.0 48.0 036 1200 0.25 67.8 63.8 59.8 56.8 54.8 52.8 48.8 042 1400 0.25 68.4 64.4 60.4 57.4 55.4 53.4 49.4 048 1600 0.25 69.0 65.0 61.0 58.0 56.0 54.0 50.0 060 2000 0.25 70.0 66.0 62.0 59.0 57.0 55.0 51.0

* Est. sound power levels have been derived using the method described in the 1987 ASHRAE HVAC Systems & Applications Handbook, Chap. 52, p. 52.7.

CONDITIONS OCTAVE BAND CENTER FREQUENCY*

CFM

Ext Static Pressure

63 125 250 500 1000 2000 4000

ELECTRICAL DATA FOR UNITS WITH FACTORY--INSTALLED HEA TERS

SINGLE CIRCUIT DUAL CIRCUIT

MODEL NO

FY4ANB060010 3/4 5.2 MKFCEH0901N10 36.2/40.0 51.8/56.5 50/60 --- --- --- --- --- --- FY4ANB060015 3/4 5.2 MKFCEH1501F15 54.2/59.9 74.3/81.4 80/80 36.2/40.0 51.8/56.5 60/60 18.1/20.0 22.6/25.0 25/25 FY4ANF018005 1/6 1.8 MKFCEH0501N05 18.1/20.0 24.9/27.3 25/30 --- --- --- --- --- --- FY4ANF018008 1/6 1.8 MKFCEH0801N08 28.9/32.0 38.4/42.3 40/45 --- --- --- --- --- --- FY4ANF024005 1/4 1.8 MKFCEH0501N05 18.1/20.0 24.9/27.3 25/30 --- --- --- --- --- --- FY4ANF024010 1/4 1.8 MKFCEH0901N10 36.2/40.0 47.5/52.3 50/60 --- --- --- --- --- --- FY4ANF030008 1/4 1.5 MKFCEH0801N08 28.9/32.0 38.0/41.9 40/45 --- --- --- --- --- --- FY4ANF030010 1/4 1.5 MKFCEH0901N10 36.2/40.0 47.1/51.9 50/60 --- --- --- --- --- --- FY4ANF036010 1/3 2.4 MKFCEH0901N10 36.2/40.0 48.3/53.0 50/60 --- --- --- --- --- --- FY4ANF036015 1/3 2.4 MKFCEH1501F15 54.2/59.9 70.8/77.9 80/80 36.2/40.0 48.3/53.0 50/60 18.1/20.0 22.6/25.0 25/25 FY4ANF042010 1/2 2.9 MKFCEH0901N10 36.2/40.0 48.9/53.6 50/60 --- --- --- --- --- --- FY4ANF042015 1/2 2.9 MKFCEH1501F15 54.2/59.9 71.4/78.5 80/80 36.2/40.0 48.9/53.6 50/60 18.1/20.0 22.6/25.0 25/25 FY4ANF048010 3/4 4.3 MKFCEH0901N10 36.2/40.0 50.6/55.4 50/60 --- --- --- --- --- --- FY4ANF048015 3/4 4.3 MKFCEH1501F15 54.2/59.9 73.1/80.3 80/80 36.2/40.0 50.6/55.4 60/60 18.1/20.0 22.6/25.0 25/25

NOTE: All units 208/230, single--- phase, 60 Hz MCA - -- Minimum Circuit Amps FLA --- Fu ll L oa d A m ps

MTRHPMTR

FLA

HEAT PACK

INSTALLED

HTR

AMPS

MCA

MAX

OVERCUR

PROTECT

HTR

AMPS

L1/L2 L1/L2 L1/L2 L3/L4 L3/L4 L3/L4

MCA

MAX

OVERCUR

PROTECT

HTR

AMPS

MCA

MAX

OVERCUR

PROTECT

Page 12

PERFORMANCE DATA (cont)

ELECTRICAL DATA FOR UNITS WITH FACTORY--INSTALLED HEA TERS (cont)

SINGLE CIRCUIT DUAL CIRCUIT

MODEL NO

FA4CNB060010 3/4 5.2 MKFCEH0901N10 36.2/40.0 51.8/56.5 50/60 --- --- --- --- --- ---

FA4CNB060015 3/4 5.2 MKFCEH1501F15 54.2/59.9 74.3/81.4 80/80 36.2/40.0 51.8/56.5 60/60 18.1/20.0 22.6/25.0 25/25 FA4CNC018005 1/6 1.8 MKFCEH0501N05 18.1/20.0 24.9/27.3 25/30 --- --- --- --- --- --- FA4CNC024005 1/4 1.8 MKFCEH0501N05 18.1/20.0 24.9/27.3 25/30 --- --- --- --- --- --- FA4CNC030008 1/4 1.5 MKFCEH0801N08 28.9/32.0 38.0/41.9 40/45 --- --- --- --- --- --- FA4CNC036010 1/3 2.4 MKFCEH0901N10 36.2/40.0 48.3/53.0 50/60 --- --- --- --- --- --- FA4CNC042010 1/2 2.9 MKFCEH0901N10 36.2/40.0 48.9/53.6 50/60 --- --- --- --- --- --- FA4CNC048010 3/4 4.3 MKFCEH0901N10 36.2/40.0 50.6/55.4 50/60 --- --- --- --- --- --- FA4CNC060010 3/4 5.2 MKFCEH0901N10 36.2/40.0 51.8/56.5 50/60 --- --- --- --- --- ---

FA4CNF018005 1/6 1.8 MKFCEH0501N05 18.1/20.0 24.9/27.3 25/30 --- --- --- --- --- ---

FA4CNF018008 1/6 1.8 MKFCEH0801N08 28.9/32.0 38.4/42.3 40/45 --- --- --- --- --- ---

FA4CNF024005 1/4 1.8 MKFCEH0501N05 18.1/20.0 24.9/27.3 25/30 --- --- --- --- --- ---

FA4CNF024010 1/4 1.8 MKFCEH0901N10 36.2/40.0 47.5/52.3 50/60 --- --- --- --- --- ---

FA4CNF030008 1/4 1.5 MKFCEH0801N08 28.9/32.0 38.0/41.9 40/45 --- --- --- --- --- ---

FA4CNF030010 1/4 1.5 MKFCEH0901N10 36.2/40.0 47.1/51.9 50/60 --- --- --- --- --- ---

FA4CNF036010 1/3 2.4 MKFCEH0901N10 36.2/40.0 48.3/53.0 50/60 --- --- --- --- --- ---

FA4CNF036015 1/3 2.4 MKFCEH1501F15 54.2/59.9 70.8/77.9 80/80 36.2/40.0 48.3/ 53.0 50/60 18.1/ 20.0 22.6/25.0 25/25

FA4CNF042010 1/2 2.9 MKFCEH0901N10 36.2/40.0 48.9/53.6 50/60 --- --- --- --- --- ---

FY4A / FA4C

FA4CNF042015 1/2 2.9 MKFCEH1501F15 54.2/59.9 71.4/78.5 80/80 36.2/40.0 48.9/ 53.6 50/60 18.1/ 20.0 22.6/25.0 25/25

FA4CNF048010 3/4 4.3 MKFCEH0901N10 36.2/40.0 50.6/55.4 50/60 --- --- --- --- --- ---

FA4CNF048015 3/4 4.3 MKFCEH1501F15 54.2/59.9 73.1/80.3 80/80 36.2/40.0 50.6/ 55.4 60/60 18.1/ 20.0 22.6/25.0 25/25 NOTE: All units 208/230, single--- phase, 60 Hz MCA - -- Minimum Circuit Amps FLA --- Fu ll L oa d A m ps

MTRHPMTR

FLA

HEAT PACK INSTALLED

HTR

AMPS

MCA

MAX

OVERCUR

PROTECT

HTR

AMPS

L1/L2 L1/L2 L1/L2 L3/L4 L3/L4 L3/L4

MCA

MAX

OVERCUR

PROTECT

HTR

AMPS

MCA

ELECTRICAL DATA FOR UNITS WITHOUT FACTORY--INSTALLED HEATERS

MODEL NO

FY4ANB060T00 FY4ANB060000 FY4ANF018T00 FY4ANF018000 FY4ANF024T00 FY4ANF024000 FY4ANF030T00 FY4ANF030000 FY4ANF036T00 FY4ANF036000 FY4ANF042T00 FY4ANF042000 FY4ANF048T00 FY4ANF048000

* Usecopperwireonly.Use75_C only in this application. When using non--- metallic (NM) sheathed cable, wire size required should be based on that of

_C conductors, instead of wire sizes shown in table above per NEC Article 336- -- 26.

NOTES: If branch circuit wire length exceeds 100 ft. (30m), consult NEC 215 ---2 to determine maximum wire length. Use 2% voltage drop.

All units 208/230, single --- phase, 60 Hz.

FLA --- Fu ll L oa d A m ps

MTRHPMTR

3/4 5.2 6.5 15 14

1/6 1.8 2.3 15 14

1/4 1.8 2.3 15 14

1/4 1.5 1.9 15 14

1/3 2.4 3.0 15 14

1/2 2.9 3.6 15 14

3/4 4.3 5.4 15 14

FLA

MCA

MAX

OVERCUR

PROTECT

MIN WIRE

SIZE AWG*

MODEL NO

FA4CNB060000 3/4 5.2 6.5 15 14

FA4CNF018000 1/ 6 1.8 2.3 15 14 FA4CNF024000 1/ 4 1.8 2.3 15 14 FA4CNF030000 1/ 4 1.5 1.9 15 14 FA4CNF036000 1/ 3 2.4 3.0 15 14 FA4CNF042000 1/ 2 2.9 3.6 15 14 FA4CNF048000 3/ 4 4.3 5.4 15 14

MTRHPMTR

FLA

MCA

MAX

OVERCUR

PROTECT

FACTORY--INSTALLED HEATER OPTIONS*

MODEL 018 024 030 036 042 048 060

FA4CN(F,B) 5, 8 5, 10 8, 10 10, 15 10, 15 10, 15 10, 15 FA4CNC 5 5 8 10 10 10 10

FY4AN(F,B) 5, 8 5, 10 8, 10 10, 15 10, 15 10, 15 10, 15 * For field---installed heater/fan coil combinations, see Electric Heater Internal Protection below. 6th digit: B --- M od u l a r c ab i n et , C --- D i s c on n e c t, F --- S in g l e p i e ce ca bi n e t

ELECTRIC HEATER INTERNAL PROTECTION*

HEATER KW PHASE FUSE QTY/SIZE CKT BKR QTY/SIZE{

3 1 — — 5 1 — 1/60

8 1 — 1/60 10 1 — 1/60 15 1 2/30 — 2/60 2/60 20 1 4/60 2/60 24 1/3 6/60 — 30 1/3 6/60 —

9 1/3 — — 15 3 — —

* 5 --- , 8 --- , 10 --- kW f a ct or y --- i n st al l ed h e at h a s n o i n t e r n a l pr ot e c ti o n . 1 5 --- k W f a ct o r y --- i ns t a l l e d h e a t is i n te r n a l l y pr o t e ct ed w i t h f u se s. { Circuit breakers are 2 pole.

18 3 — —

MAX

OVERCUR

PROTECT

MIN WIRE

SIZE AWG*

Page 13

Dual Circuit

208/230V (Ft)‡

Max Wire Length

Single

Circuit

208/230V (FT)‡

MAX WIRE LENGTH

Dual Circuit

208/230V

Max Fuse/CktBkr Amps

Single

Circuit

AMPS

208/230V

MAX FUSE/CKT BKR

Dual Circuit

208/230V

Min Gnd Wire Size

BRANCH CI RCUIT

Single

Circuit

MIN GND

208/230V

WIRE SIZE

FY4A / FA4C

ACCESSORY ELECTRIC HEATER ELECTRICAL DATA

208/230V†

Min W ire Siz e ( AWG)

208/230V*

Min Ampacity

208/230V

HEATER AMPS

CIRCUIT

INTERNAL

PHASE

HEATER

Dual Circuit

Single

Circuit

Dual Circuit

Single

Circuit

Dual Circuit

Single

Circuit

TION

PROTEC-

208/230V†

MIN WIRE SIZE ( AWG)

208/230V*

MIN AMPACITY

208/230V

HEATER AMPS

PHASE

240V 208V L1 ,L2 L3,L4 L5,L6 L1, L2 L3,L4 L5, L6 L1,L2 L3,L4 L5,L6 L1, L2 L3,L4 L5,L6 L1,L2 L3,L4 L5 ,L6

5 3.8 1 None 18.1/20.0 — — 26.0/ 28.4 — — 10/10 — — 10/10 — — 30/ 30 — — 66/66 — —

5 3.8 1 None 18.1/20.0 — — 31.2/ 33.5 — — 8/8 — — 10/ 10 — — 35/35 — — 85/88 — —

5 3.8 1 Ckt Bkr 18.1/ 20.0 — — 26.0/28.4 — — 10/10 — — 10/ 10 — — 30/30 — — 66/66 — —

240v 208v L1,l2 L3,L4 L1,L2 L3,L4 L1 , L2 L3, L4 L1, L2 L3,L4 L1,L2 L3,L4 L1,L2 L3,L4

PART NO.

KFCEH0401N03 3 2.3 1 None 10.9/12.0 — — 15.9/17.3 — — 12/ 12 — — 12/12 — — 20/20 — — 67/68 — —

KFCEH0501N05

5 3.8 1 Ckt Bkr 18.1/ 20.0 — — 31.2/33.5 — — 8/8 — — 10/10 — — 35/ 35 — — 85/88 — —

KFCEH3001F15 15 11.3 1 Fuse 54. 2/59.9 36.2/40.0 18.1/20.0 76.3/83.4 53.8/58.5 22.7/25.0 4/4 6/6 10/10 8/ 8 10/10 10/ 10 80/90 60/ 60 25/ 25 88/89 78/80 75/76

KFCEH1601315 15 11.3 3 None 31.3/34.6 — — 47.7/51.8 — — 8/6 — — 10/ 10 — — 50/60 — — 56/90 — —

KFCEH0801N08 8 6.0 1 None 28.9/32.0 — — 44.7/48.5 — — 8/8 — — 10/ 10 — — 45/50 — — 59/60 — —

KFCEH2501C08 8 6.0 1 Ckt Bkr 28.9/32.0 — — 44.7/ 48.5 — — 8/8 — — 10/ 10 — — 45/50 — — 59/60 — —

KFCEH2901N09 9 6.8 1 None 32.8/36.0 — — 49.5/53.5 — — 8/6 — — 10/ 10 — — 50/60 — — 54/87 — —

KFCEH0901N10 10 7. 5 1 None 36.2/40.0 — — 53.8/58.5 — — 6/6 — — 10/ 10 — — 60/60 — — 78/80 — —

KFCEH0501N05

KFCEH2401C05

KFCEH2601C10 10 7.5 1 Ckt Bkr 36.2/40.0 — — 53.8/58. 5 — — 6/6 — — 10/ 10 — — 60/60 — — 78/80 — —

KFCEH2901N09** 9 6. 8 3 None 18.8/ 20.8 — — 32.0/34.5 — — 8/8 — — 10/10 — — 35/35 — — 83/85 — —

KFCEH2001318 18 13.5 3 None 37.6/41.5 — — 55.5/60.4 — — 6/6 — — 10/8 — — 60/70 — — 76/ 77 — —

KFCEH3101C15 15 11. 3 1 Ckt Bkr — 36.2/ 40.0 18. 1/20.0 — 53.8/58.5 22.7/25.0 — 6/ 6 10/10 — 10/10 10/10 — 60/60 25/25 — 78/80 75/ 76

24 18.0 3 Fuse 50.1/55. 4 — — 71. 2/77.8 — — 4/ 4 — — 8/8 — — 80/80 — — 94/95 — —

24 18.0 1 Fuse 86.7/95. 5 — — 116.9/127.9 — — 1/ 1 — — 6/6 — — 125/150 — — 115/116 — —

30 22.5 3 Fuse 62.6/69. 2 — — 86. 8/95.0 — — 3/ 3 — — 8/8 — — 90/100 — — 97/98 — —

30 22.5 1 Fuse 109.0/120.0 — — 144.8/ 158.5 — — 0/00 — — 6/6 — — 150/175 — — 117/150 — —

NO.

HEATER PART

KFCEH3201F20 20 15.0 1 Fuse 72. 3/79.9 36.2/40.0 36.2/40.0 98.9/ 108.4 53. 8/58.5 45.3/50.0 3/2 6/6 8/8 8/6 10/10 10/10 100/110 60/60 50/50 85/109 78/80 59/59

FIELD MULTIPOINT WIRING OF 24--AND 30--kW SINGLE PHASE

KFCEH3301C20 20 15. 0 1 Ckt Bkr — 36.2/ 40.0 36. 2/40.0 — 53.8/58.5 45.3/50.0 — 6/ 6 8/8 — 10/10 10/10 — 60/ 60 50/ 50 — 78/80 59/ 59

KFCEH3401F24††

KFCEH3501F30††

KFCEH3401F24†† 24 18.0 1 28.9/32.0 28.9/32.0 28.9/32.0 44.7/48.5 36.2/40.0 36.2/40.0 8/8 8/8 8/8 10/10 45/50 40/40 40/40 59/60 73/73 73/73

KFCEH3501F30†† 30 22.5 1 36.2/40.0 36.2/40.0 36.2/40.0 53.8/58.5 45.3/50.0 45.3/50.0 6/6 8/8 8/8 10/10 60/60 50/50 50/50 78/80 59/59 59/59

tables of the National Electric Code (ANSI/NFPA 70).

* Includes blower motor amps of largest fan coil used with heater.

{ Copper wire must be used. If other than uncoated (non--- plated), 75_C ambient, copper wire (solid wire for 10 AWG and smaller, stranded wire for larger than 10 AWG) is used, consult applicable

} Length shown is as measured 1 way along wire path between unit and service panel for a voltage drop not to exceed 2%.

** Field convertible to 3 phase.

{{ Field convertible to 1 phase, single or multiple supply circuit.

NOTES:

1. For fan coil sizes 018---036.

2. For fan coil sizes 042---060.

3. Singl e circuit application of F15 and F20 heaters requires single ---point wiring kit accessory.

Page 14

ACCESSORIES

ITEM ACCESSORY PART NO.* FAN COIL SIZE USED WITH

1. Disconnect Kit KFADK0201DSC Cooling controls and heaters 3 --- through 10---kW KFACB0101CFB 018

2. Downflow Base Kit

3. Downflow Conversion Kit

4. Single---Point Wiring Kit KFASP0101SPK O n l y w it h 1 5 --- a n d 20 --- kW F u s e d H e a t e r s

5. Filter Kit (12 Pack)

6. PVC Condensate Trap Kit (50 pack) KFAET0150ETK All

7. Air Cleaner 240- -- volt Conversion Kit KEAVC0201240 All

8. Downflow/Horizontal Conversion Gasket Kit KFAHD0101SLP All

9. Horizontal Water Management Kit (25 pack) KFAHC0125AAA All

* Factory authorized and listed, field ---installed.

KFACB0201CFB 024, 030 KFACB0301CFB 036, 042, 048 KFACB0401CFB 060

KFADC0201SLP Slope Coil Units—018, 024, 030, 036

KFADC0401ACL A---Coil Units—042, 048, 060

KFAFK0112SML 018

KFAFK0212MED 024, 030

KFAFK0312LRG 036, 042, 048

KFAFK0412XXL 060

ACCESSORY KITS DESCRIPTION SUGGESTED AND REQUIRED USE.

FY4A / FA4C

1. Disconnect Kit The kit is used to disconnect electrical power to the fan coil so service or maintenance may be performed safely. SUGGESTED USE: Units for 3-- through 10--kW electric resistance heaters and cooling controls.

2. Downflow Base Kit This kit is designed to provide a 1 --in. minimum clearance between unit discharge plenum, ductwork, and combustible materials. It also provides a gap--free seal with the floor. REQUIRED USE: This kit must be used whenever fan coils are used in downflow applications.

3. Downflow Conversion Kit Fan coils are shipped from the factory for upflow or horizontal--left applications. Downflow conversion kits provide proper condensate water drainage and support for the coil when used in downflow applications. Separate kits are available for slope coils and A--coils. REQUIRED USE: This kit must be used whenever fan coils are used in downflow applications.

4. Single Point Wiring Kit The single point wiring kit acts as a jumper between L1 and L3 lugs, and between the L2 and L4 lugs. This allows the installer to run two heavy--gauge, high--voltage wires into the fan coil rather than 4 light--gauge, high--voltage wires. SUGGESTED USE: Fan coils with 15-- and 20--kW fused heaters only.

5. Filter Kit (12 pack) The kit consists of 12 fan coil framed filters. These filters collect large dust particles from the return air entering the fan coil and prevents them from collecting on the coil. This process helps to keep the coil clean, which increases heat transfer and, in turn, the efficiency of the system. SUGGESTED USE: To replace filters in fan coils. REQUIRED USE: All units unless a filter grille is used.

6. Condensate Drain Trap Kit This kit consists of 50 PVC condensate traps. Each trap is pre-- formed and ready for field installation. This deep trap helps the system make and hold proper condensate flow even during blower initiation. SUGGESTED USE: All fan coils.

7. Air Cleaner 240--volt Conversion Kit The AIRA electronic air cleaner comes ready for 115--v operation. REQUIRED USE: This kit is required when running 240--volt circuit to air cleaner.

8. Downflow/Horizontal Conversion Gasket Kit This kit provides the proper gasketing of units when applied in either a downflow or horizontal application. REQUIRED USE: Fan coils in either downflow or horizontal applications.

9. Horizontal Applications -- Water Management Kit This kit provides proper installation of fan coils under conditions of high static pressure and high relative humidity. SUGGESTED USE: All fan coils.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Catalog No: FA4C--- 5PD

Replaces: FA4C--4PD

Carrier FY4A series, FA4C series Product Data

Specifications and Main Features

Frequently Asked Questions

User Manual