Carlo Gavazzi UA 30 CLD Data Sheet

Specifications are subject to change without notice (26.10.01) 1

Ultrasonic
Diffuse, Analogue Output with Teach-in

Types UA 30 CLD .. .. M1 TI

• Cylindrical M30 polyester housing

• Sensing distance: 100-1500 mm, 200-2000 mm
or 300-3500 mm

• Outputs: Analogue 0-10 V or 4-20 mA and 2 switching
outputs PNP, NO or NC

• Teach-in functionality

• Power supply: 19 to 30 VDC

• 8° beam angle

• Protection: Short-circuit, reverse polarity, transients

• Protection degree IP 67

• M12 plug, 5 pin

Product Description

Ultrasonic sensor
Housing style
Housing size
Housing material
Housing length
Detection principle
Sensing distance
Output type
Output configuration
Connection
Teach-in

Type Selection

Housing Connection Rated operating Analogue output and Ordering no.
diameter dist. (S

n

) 2 PNP outputs NO/NC Teach-in

M30 Plug M12 100-1500 mm 0-10 VDC and 2 x PNP UA 30 CLD 15 AK M1 TI
M30 Plug M12 200-2000 mm 0-10 VDC and 2 x PNP UA 30 CLD 20 AK M1 TI
M30 Plug M12 200-2000 mm 4-20 mA and 2 x PNP UA 30 CLD 20 AG M1 TI
M30 Plug M12 200-2000 mm 2 x PNP UA 30 CLD 20 PO M1 TI
M30 Plug M12 300-3500 mm 0-10 VDC and 2 x PNP UA 30 CLD 35 AK M1 TI

Ordering Key

UA 30 CLD 35 AK M1 TI

A family of diffuse ultrasonic
sensors with sensing range
from 100-1500 mm, 200-2000
mm and 300-3500 mm with
teach-in adjustment. Adjust­ments by teach-in make it
possible to set the analog
angle according to the re­quests and program the out­put to NO or NC switching as
well. The outputs are either 0­10 V or 4-20 mA which make

it an ideal choice for distance
measurement, level measure­ment, diameter measurement
or slope control with cus­tomised settings. Due to use
of microprocessor control the
digital filtering makes the sen­sor very immune against most
electromagnetic interferences
and enables synchronisation
in an easy way.

Specifications

Rated operational volt. (Ue) 19 to 30 VDC

(ripple included)

Ripple ≤ 10%

Output current (I

e

) max. 100 mA (continuous)

for switching outputs

No-load supply current (I

o

) ≤ 45 mA

Protection Short-circuit, transients and

reverse polarity

Rated insulation voltage > 1 kV
Output

UA30CLD..AKM1TI Analogue 0-10 VDC,

2 PNP open collector
outputs, NO or NC

UA30CLD20AGM1TI Analogue 4-20 mA,

2 PNP open collector
outputs, NO or NC

UA30CLD20POM1TI 2 PNP open collector

outputs, NO or NC

Teach-in Set point adjustment

NO/NC selection

Indication Set points, 2 LED’s
Rated operating distance

UA30CLD15 .. M1 TI 100-1500 mm
UA30CLD20 .. M1 TI 200-2000 mm
UA30CLD35 .. M1 TI 300-3500 mm

Operating frequency 1 Hz
Response times

UA30CLD15/20 .. M1 TI 60 ms (target speed 1 m/s)

300 ms (step response)

UA30CLD35 AG M1 TI 120 ms (target speed 1 m/s)

500 ms (step response)

Hysteresis (H)

(differential travel) Programmable

Temperature compensation Yes
Beam angle 8°

2 Specifications are subject to change without notice (26.10.01)

Dimensions

UA 30 CLD .. .. M1 TI

Installation Hints

Relief of cable strain Protection of the sensing face Switch mounted on mobile carrierTo avoid interference from inductive voltage/
current peaks, separate the prox. switch
power cables from any other power cables,
e.g. motor, contactor or solenoid cables

Incorrect

Correct

The cable should not be pulled

A proximity switch should not serve as
mechanical stop

Any repetitive flexing of the
cable should be avoided

Specifications (cont.)

Ambient temperature

Operating

-15° to +70°C (5° to +158°F)

Storage

-25° to +85°C (-13° to +185°F)

Degree of protection IP 67 (Nema 1, 3, 4, 6, 13)
Housing material

Polyester PBTP

Connection

Plug M12, 5-pin

Weight 148 g
Tightening torque 7.5 Nm
CE-marking Yes

150 mm

1500 mm

300 mm

300 mm

250 mm

2000 mm

350 mm

3500 mm

UA 30 ... 15
UA 30 ... 20
UA 30 ... 35

Detection Range

Wiring

Pin Function

1 24 VDC
2 SP 2
3 0 V GND
4 SP 1
5 0 ... 10 V

Guaranteed detection of a
target 100 x 100 mm

Possible detection of a
large target