Cardinal Detecto PZ3000 Series, Detecto PZ3015, Detecto PZ3015L, Detecto PZ3030, Detecto PZ3060 Owner's Manual
(
PZ3000 Series
CARDINAL SCALE MFG. CO.
8528-M372-O1 Rev E
05/14
PO BOX 151
417) 673-4631 FAX (417) 673-5001
PH
www.detectoscale.com
WEBB CITY, MO 64870
Ingredient Scale
Owner’s Manual
Printed in USA
Technical Support: Ph: 866-254-8261 techsupport@cardet.com
A
INTRODUCTION
We wish to thank you for your purchase of our
PZ3000 Ingredient scale. It has been designed
and manufactured at our factory in Webb City,
MO U.S.A. with quality and reliability.
This manual will instruct you in the proper
installation, operation and maintenance of your
new scale. Please read it before attempting to
use the scale and keep it handy for future
reference.
FCC Compliance Statement
This equipment generates uses and can
radiate radio frequency and if not installed and
used in accordance with the instruction manual,
may cause interference to radio
communications. It has been tested and found
to comply with the limits for a Class A
computing device pursuant to Subpart J of Part
15 of FCC rules, which are designed to provide
reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area may cause interference in
which case the user will be responsible to take
whatever measures necessary to correct the
interference.
You may find the booklet "How to Identify and Resolve
Radio TV Interference Problems" prepared by the
Federal Communications Commission helpful. It is
available from the U.S. Government Printing Office,
Washington, D.C. 20402, stock No. 001-000-00315-4.
All rights reserved. Reproduction or use,
without expressed written permission, of
editorial or pictorial content, in any manner, is
prohibited. No patent liability is assumed with
respect to the use of the information contained
herein. While every precaution has been taken
in the preparation of this manual, the Seller
assumes no responsibility for errors or
omissions. Neither is any liability assumed for
damages resulting from use of the information
contained herein. All instructions and diagrams
have been checked for accuracy and ease of
application; however, success and safety in
working with tools depend to a great extent
upon the individual accuracy, skill and caution.
For this reason the Seller is not able to
guarantee the result of any procedure
contained herein. Nor can they assume
responsibility for any damage to property or
injury to persons occasioned from the
procedures. Persons engaging the procedures
do so entirely at their own risk.
TABLE OF CONTENTS
SPECIFICA TIONS . . . . . . . . . . . . . . . . . . . .. . .
INST ALLA TION . . . . . . . . . . . . . . . . . . . . . . . . .
POWER CONNECTION . . . . . . . . . . . . . . . . . . 4
Power Supply . . . . . . . . . . . . . . . . . . . . .. . . .
Battery Operation . . . . . . . . . . . . . . . . . .. . .
Battery Charging . . . . . . . . . . . . . . . . . . . . ..
Battery Installation/Replacement . . . . . . . . 4
Extended Battery Operation . . . . . . . . . . . .
OPTIONAL ZERO DEVICES . . . . . . . . . . . . . .
KEYP AD DESCRIPTION . . . . . . . . . . . . . . . . .
NNUNCIA TORS . . . . . . . . . . . . . . . . . . . . . . . 9
OPERA TION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CARE AND MAINTENANCE . . . . . . . . . . . . . .
SETUP AND Calibration . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . .
P ARTS IDENTIFICATION . . . . . . . . . . . . . . . .14
Weight Display
Dimensions
Display
Scale Base
PZ3015
PZ3015L
PZ3030
PZ3060
Zero
Power
Requirements
Tare
Operation
Temperature
Humidity
Capacity
Certifications
SPECIFICATIONS
6 Digit, 0.7" LCD
Digital Display
7.5" W x 1.5" D x 4.5" H
8" W x 8" D x 1.75" H
12" W x 12" D x 1.75" H
12" W x 12" D x 1.75" H
14" W x 12" D x 3" H
Established on power up
routine and maintained by
auto-zero circuitry.
100 to 240 VAC 50/60Hz 12
VDC 1A wall plug-in UL/CSA
listed AC power adapter
(Cardinal part number
6800-1045) OR optional 6 “AA”
NiMH batteries (1.2v/2700
mAh). NOTE: On PZ3060, the
batteries (Cardinal part number
6800-0020) ARE included.
ZERO key on keypad, Lite Way
Sensor or optional Foot Switch
or Piezo Button
30 to 110 °F (-1 to 43 °C)
75% without condensation
15lb x 0.005
30lb x 0.01
60lb x 0.02
NOT LEGAL FOR TRADE
1
3
4
4
4
6
7
8
10
10
11
13
8528-M372-O1 Rev E PZ3000 Series
1
2
Serial Number_______________________
Date of Purchase ____________________
Purchased Form_____________________
___________________________________
___________________________________
RETAIN THIS INFORMATION FOR FUTURE USE
PRECAUTIONS
Before using this instrument, read this
manual and pay special attention to all
"NOTIFICATION" symbols:
IMPORTANT ELECTRICAL
WARNING
8528-M372-O1 Rev E PZ3000 Series
INSTALLATION
1. Carefully remove the scale base and display from the shipping carton and inspect them for
any evidence of damage (such as exterior dents and scratches) that may have taken place
during shipment. Remove the packing material from the scale base and on the PZ3030, the
shipping screw on the bottom of the scale base. Next, remove the protective covering from
the display and keypad. Keep the carton, packing material and shipping screw (on the
PZ3030) for return shipment if it should become necessary . NOTE: It is the r espon sibility of
the purchaser to file all claims for any damages or loss incurred during transit.
2. To mount the display on the scale base, locate the two mounting screws on the display and
the two slotted holes in the scale base bracket.
3. Lift the scale (by the bracket) high enough to allow you to align the two screws on the
display with the large end of the two slotted holes in the bracket. Place the screws on the
display in the bracket and gently pull forward to secure the display to the bracket.
4. Plug the AC power supply into the power jack, located on the bottom side of the display (refer
to Figure 1) and then connect the AC power adapter into the proper electrical outlet.
5. If it is desired to use the scale remotely (no AC power), with the exception of the PZ3060, you
must first obtain and install 6 NiMH batteries (2300mAh minimum). The batteries should then
be allowed to charge approximately 8 hours. Charging the batteries for more than 8 hours
will not harm them. The scale may be operated while the batteries are charging.
6. Place the scale on a stable, vibration-free, level surface away from direct sunlight and any
rapidly moving air source (heating and cooling vents).
7. Place commodity tray on the scale. The scale is now ready to use.
CAUTION! DO NOT place the scale on any unstable cart, stand or table. The
scale may fall causing injury to the operator, and seriously damage the unit, or
proper operation of the scale may be inhibited.
Display
Mounting
Screws
Figure No. 1
8528-M372-O1 Rev E PZ3000 Series
Optional
Zero Device
Connector
Power
Supply
Jack
Scale
Base
Cable
3
POWER CONNECTION
NOTE: The PZ3000 can be operated from a power supply or from 6 “AA” size,
(2300mAh minimum) NiMH batteries. The power supply is also used to recharge the
NiMH batteries. Batteries are available by ordering Cardinal part number, 6800-0020.
Power Supply
To power the PZ3000 using the power supply, connect the power supply's connector into the
power jack on the bottom side of the display and then connect the 12 VDC, 1 Amp power adapter
into the proper electrical outlet. See Figure 1. On models requiring 220 VAC, it is the customer’s
responsibility to obtain the correct power adapter plug. The scale is now ready for operation.
Battery Operation
Battery operation is a standard feature of the PZ3000 Series Ingredient Scale, although
the batteries are optional (not included, except on model PZ3060). The scale will operate for up
to 50 hours on fully charged batteries depending on the condition of the batteries (from new to
about 500 recharges). The battery bar graph indicates the battery capacity in 4 steps:
4 segments - the full battery capacity is available,
3 segments - the battery is at 75% of capacity,
2 segments - the battery is at 50% of capacity,
1 segment: - the battery is at 25% capacity.
When the battery voltage drops too low for accurate weighing, the display will show LoBAt an d
then shut off. You will be unable to turn the display back on until the AC power supply is
connected to the display to operate it and recharge the batteries.
Battery Charging
To recharge the NiMH batteries, the AC power supply must be connected to a power outlet and
plugged into the display. It will take approximately 4 to 8 hours to fully recharge the batteries in
the display. Charging the batteries for more than 8 hours will not damage them . NOTE: The
scale may be operated while the batteries are charging.
Battery Installation/Replacement
To install or remove the batteries, the following steps should be followed:
1. Remove the indicator from the scale,
wall or table stand.
2. Turn the indicator so that the display
is facing away from you and place it
face down on a table or bench.
3. Referring to Figure No.2, locate the
two screws on the angled edge of
indicator. NOTE: The PZ3015 and
PZ3030 use two thumbscrews and
the PZ3060 uses two socket head
cap screws instead of thumbscrews.
4. Remove the screws and washers
under them.
5. Lift the battery door exposing the
battery holder.
6. Referring to Figure No. 3, locate and
remove the connector on the end of
the battery holder.
Remove these Screws
Figure No. 2
4
8528-M372-O1 Rev E PZ3000 Series
POWER CONNECTION, CONT.
7. Slide one side of the battery door so that it clears the edge of the indicator enclosure and
then remove the battery door.
8. Place the battery door on a table or bench with the battery holder and battery strap up.
9. Referring to Figure No. 3, remove the 2 Philips screws securing the battery strap to the
battery door and remove the strap.
Battery Strap
Figure No. 3
Remove Philips Screws
10. To install or replace the batteries, first remove the battery holder cover by pushing in on
the tab and lifting it up. Refer to Figure No. 4.
11. If replacing the batteries, remove all 6 batteries from the battery holder. If installing new
batteries, proceed to step 12.
NOTE: To insure optimum performance of your PZ3000 when powered by the
internal battery, replace all 6 batteries with new “AA” size, NiMH batteries
(2300mAh minimum). DO NOT mix new and used batteries.
Battery
Connector
Figure No. 4
Push in and
lift here
12. Install the 6 new “AA” size batteries in the battery holder, noting the polarity markings
located in the battery holder. Refer to Figure No. 5.
13. After placing all 6 batteries in the holder, replace the battery cover and battery strap.
Secure the battery strap with the 2 Philips screws removed earlier.
14. Replace the battery door on the indicator and then re-connect the connector on the end of
the battery holder.
8528-M372-O1 Rev E PZ3000 Series
Battery
Cover
5
Figure No. 5
POWER CONNECTION, CONT.
+
-
-
+
6 “AA” Size NiMH Batteries
(2300mAh minimum)
15. Insuring no wires are between the battery door and the back of the indicator, lower the
battery door.
16. Install the two screws and washers removed in step 4. NOTE: The PZ3015 and PZ3030
use thumbscrews and should be finger-tightened only.
17. Return the indicator to the scale, wall or table stand.
18. Apply power to the PZ3000 using the power supply, to begin charging the new batteries.
19. The scale is now ready for operation.
+
-
-
+
+
-
-
+
Extended Battery Operation
In operations that require the remote use (no AC power) of the scale beyond the approximately
50 hours of continuous use, an auxiliary battery door assembly (CPN 8528-C365-0A) and 6 “AA”
size, 2300 mAh minimum batteries (CPN 6800-0020) can be purchased to easily accommodate
your operation.
The following steps describe how to remove the battery door and re-charge the batteries
externally using the AC power adapter (battery charger).
1. Remove the indicator from the scale, wall or table stand.
2. Turn the indicator so that the display is facing away from you and place it face down on a
table or bench.
3. Referring to Figure No.2, locate the two screws on the angled edge of the indicator and
remove the screws and washers under them. NOTE: The PZ3015 and PZ3030 use two
thumbscrews and the PZ3060 uses two socket head cap screws.
4. Referring to Figure No. 6 remove the connector from the end of the battery holder and
then remove the battery door and set it aside.
5. Place the auxiliary battery door with fully recharged batteries on the indicator and then
re-connect the connector to the end of the battery holder. See Figure No. 6.
6. Insuring no wires are between the battery door and the back of the indicator, lower the
battery door and install the two screws and washers removed in step 3. NOTE: The
PZ3015 and PZ3030 use thumbscrews and should be finger-tightened only.
7. Return the indicator to the scale, wall or table stand. The scale is ready for operation.
8. Place the battery door removed in step 5 on a table or bench with the battery holder and
battery strap up.
6
8528-M372-O1 Rev E PZ3000 Series
POWER CONNECTION, CONT.
9. Referring to Figure No. 6, locate the battery charger jack on the battery door.
10. Plug the AC power adapter (battery charger) into the jack on the battery door and then
connect the AC power adapter (battery charger) into the proper electrical outlet.
11. Allow approximately 4 to 8 hours to fully recharge the batteries.
Figure No. 6
Battery
Charger
Jack
Battery
Connector
OPTIONAL ZERO DEVICES
In addition to the standard display pushbutton and “Lite Way” hands-free methods to zero the
weight, the PZ3000 Series has an optional Foot Pedal or Mountable Pushbutton available. The
model numbers for the optional zero devices are:
PZFS for the foot pedal and
PZPB for the mountable pushbutton.
Figure No. 7
Power
Supply
Jack
Scale
Base
Cable
Optional
Zero Device
Plugs in Here
8528-M372-O1 Rev E PZ3000 Series
7
Loading...