Cardinal C410 Operating Instructions & Parts List Manual

C410 ELECTRIC TOOL

Operating Instructions & Parts List

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

2

WARNING:

WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED TO REDUCE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY.

PICTURE OF TOOL WITH LABELED PARTS

Figure 1 RIVNUT® Engineered Products RIVNUT® Header C-410

Weight - 7lbs.

Anvil 1

Anvil Locknut 1A

Pull-up Stud 2

Nose Piece Housing 9
Housing Locknut 10
Trigger 57

Reverse Switch 57A

C410 Electric Tool

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

READ ALL INSTRUCTIONS

Grounding Instructions

This tool should be grounded while in use to protect the operator from electric shock. The tool is
equipped with a 3-conductor cord and 3-prong grounding type plug to t the proper grounding type
receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never
connect the green (or green and yellow) wire to a live terminal.

Extension Cords

Use only 3-wire extension cords that have 3-prong grounding type plugs and 3-pole receptacles that
accept the tool’s plug. Replace or repair damaged cords. The cord must be heavy enough to carry the
current the tool will draw. Do not use an undersized cord which will cause a drop in line voltage
resulting in loss of power and overheating.

Keep Work Area Clean

Cluttered areas and benches invite injuries.

Consider Work Area Environment

Don’t expose power tools to rain. Don’t use power tools in damp or wet locations. Keep work area well
lit. Do not use tool in presence of ammable liquids of gases.

Guard Against Electric Shock

Prevent body contact with grounded surfaces. For example: pipes, radiators, steel enclosures.

Keep Children Away

Do not let visitors contact tool or extension cord. All visitors should be kept away from work area.

Store Idle Tools

When not in use, tools should be stored in a dry place.

Use Safety Glasses

Don’t Abuse Cord

Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp
edges.

3

C410 Electric Tool

Safety Precautions

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

Disconnect Tools

When not in use, before servicing and when changing thread size (pull-up, stud, coupling, anvil) or replacing
carbon brushes.

Avoid Unintentional Starting

Don’t carry plugged-in tool with nger on switch. Be sure switch is o when plugged in.

Outdoor Use Extension Cords

When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

Stay Alert

Watch what you are doing. Use common sense. Do not operate tool when you are tired.

Check Damaged Parts

Before further use of the tool, a part that is damaged should be carefully checked to determine that it will
operate properly and preform its intended function. Have defective switches replaced by RIVNUT
Engineered Products. Do not use tool if switch does not turn it on and o.

INTRODUCTION

A. General / RIVNUT Header Tool
The C-410 electric header tool is especially
designed to install RIVNUT brand metal
fasteners. See Operating Range Chart I.
The C-410 header tool will provide long
service when kept clean and in proper
adjustment.

B. Electrical Supply Requirements
Specications for Model C-410
Power Source:

- Single phase

- Voltage 120V

- Cycle 60 Hz

- AMPS 3.70

RIVNUT MATERIAL

Aluminum Brass & Stainless
Steel Steel
#4
#6
#8
#10
1/4”
5/16”
M3
M4
M5
M6
M7
M8

Recommended

4

C410 Electric Tool

Safety Precautions Continued

and Introduction

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

5

Operating and Adjustments

C410 Electric Tool

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

C410 Electric Tool

6

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

TROUBLE SHOOTING

MAINTENANCE

7

C410 Electric Tool

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

8

C410 Electric Tool

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]

RIVNUT HEADER C-410

9

Visa, Mastercard, Discover & AMEX Accepted Fax: [phone]

ISO CERTIFIED

800.236.3200 [e-mail]