Page 1
Intelligent Scale Base
Setup and Operation Manual
CARDINAL SCALE MFG. CO.
8541-M106-O1 Rev B
12/02
PO BOX 151 • WEBB CITY, MO 64870
PH (417) 673-4631 • FAX (417) 673-5001
Web Site - http://www.detectoscale.com
Printed in USA
Page 2
1
Page 3
INTRODUCTION
TABLE OF CONTENTS
Thank you for your purchase of our Detecto
AS-400D Series Intelligent Scale Base. It was
built with Detecto quality and reliability at our
factory in Webb City, Missouri. The AS-400D
series scales consist of the AS-400D, AS410D and AS-420D. All scales are equipped
with a bi-directional RS232C compatible port
for communication with a computer.
FCC COMPLIANCE STATEMENT
Notice: This equipment generates, uses and
can radiate radio frequency energy and if not
installed and used in accordance with the
instruction manual, may cause interference to
radio communications. It has been tested and
found to comply with the limits for a Class A
computing device pursuant to Subpart J of
Part 15 of FCC rules, which are designed to
provide reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area may cause interference in
which case the user will be responsible to take
whatever measures necessary to correct the
interference.
TRADEMARKS
All rights reserved. Reproduction or use, without
expressed written permission, of editorial or pictorial
content, in any manner, is prohibited. No patent liability
is assumed with respect to the use of the information
contained herein. While every precaution has been
taken in the preparation of this manual, the Seller
assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting
from use of the information contained herein. All
instructions and diagrams have been checked for
accuracy and ease of application; however, success
and safety in working with tools depend to a great
extent upon the individual accuracy, skill and caution.
For this reason the Seller is not able to guarantee the
result of any procedure contained herein. Nor can they
assume responsibility for any damage to property or
injury to persons occasioned from the procedures.
Persons engaging the procedures do so entirely at their
own risk.
Serial Number ______________________
Date of Purchase____________________
Purchased From ____________________
__________________________________
__________________________________
RETAIN THIS INFORMATION FOR FUTURE USE
INTRODUCTION - - - - - - - - - - - - - - - - - -
SPECIFICATIONS - - - - - - - - - - - - - - - - -
INSTALLATION - - - - - - - - - - - - - - - - - - -
BAUD RATE AND
WEIGHT MODE SELECTION - - - - - - - - -
SERIAL INTERFACE PROTOCOL - - - - - SCALE WEIGHT DATA STRINGS - - - - - CALIBRATION - - - - - - - - - - - - - - - - - - - -
CARE AND MAINTENANCE - - - - - - - - - -
SPECIFICATIONS
Scale Capacity:
400D = 100 lb
410D = 150 lb
420D = 200 lb
Platform Size:
400D
410D
420D
Display: 6 digit, 7 segment,
Annunciators lb, lb-oz, ZERO
External Controls ZERO Button
Power 110 to 120 VAC
The AS 400D Series scale is shipped from
the factory in the following configuration:
9600 Baud 8 Data Bits
No Parity 1 Stop Bit
Pounds/Ounces Mode
(NOTE! AS-420D is Pounds only)
PRECAUTIONS
Before using this instrument, read this
manual and pay special attention to all
"WARNING" symbols:
IMPORTANT ELECTRICAL
WARNING
0 to 100 lb x 0.5 oz
0 to 100 lb x 0.5 oz &
100 to 150 lb x 1 oz
0-200 lb x 0.1 lb
18 in x 18 in
(46 cm x 46 cm)
24” x 24”
(61 cm x 61 cm)
red LED, 1/2" high
(50/60 Hz)
1
1
2
3
4
4
5
5
1
Page 4
INSTALLATION
On receipt of your AS-400D series scale, carefully unpack the scale removing all packing
material. Examine the scale to make certain there is no shipping damage. Should damage be
discovered contact the shipping company as soon as possible. The packing material and
shipping carton should be retained for possible examination by the shipping company.
Determine where the scale is to be located. It should be a smooth surface capable of
supporting both the scale and any load apt to be placed on the scale. It should not be in direct
sunlight nor should it be subject to air flow from heating/cooling vents, fans or similar devices.
Place the scale in the chosen location and remove the stainless steel platform. The platform
can be removed by lifting upward on it removing it from the weighbridge. Locate the small
level indicator on the weighbridge and check to make certain that the scale is level. If the level
indicator does not show a level indication, the mounting feet should be adjusted to obtain a
level condition. To adjust a mounting foot, first loosen the lock nut then turn the mounting foot
in the required direction to raise or lower that corner of the scale. Once a level condition has
been achieved, secure the mounting foot settings by tightening each of the lock nuts. Replace
the platform on the weighbridge.
Plug the power cord into a 115/120 VAC grounded polarized power outlet, making certain that
the power cord is not in the way of normal traffic.
If you are unsure whether your power outlet is correct, you should consult a
qualified electrician.
Plug the power cord into the power receptacle on the rear of the scale base. If the display
illuminates with a display segment test, installation of the scale is complete. If not, check to
make sure that the power outlet and the scale fuse are good.
Mounting Foot
NOT LEVEL LEVEL
Bubble is not Bubble is
within circle within circle
Locking Nut
2
Page 5
BAUD RATE AND WEIGHT MODE SELECTION
The AS-400D and AS-410D can be operated in either a pounds/ounces mode or UPS pounds
only mode. A setup switch makes this selection. The AS-420D operates only in a pounds
mode and cannot be set to a pounds/ounces mode of operation.
NOTE! Although the AS-420D operates in a pounds only mode, it does not use
the UPS pounds only command set.
Switch S1 (2, 3 and 4) are used to select the baud rate for serial communication via the scale
port. Switch S1 (1 and 5) are used to select the weight mode.
To gain access to the switch S1:
1. Unplug the scale from the power outlet.
2. Remove the stainless steel platform.
3. Once the platform has been removed, you will see the switch located on the main
printed circuit board.
4. Using a small screwdriver or similar device, set the five switches to the desired setting
as indicated in the table.
5. Replace the scale platform, and then plug in the power cord. This will reset and restart
the scale for normal operation.
FUNCTION SETTING S1-1 S1-2 S1-3 S1-4 S1-5
Baud Rate
19200 OFF OFF OFF
9600 ON OFF OFF
4800 OFF ON OFF
2400 ON ON OFF
1200 OFF OFF ON
600 ON OFF ON
300 OFF ON ON
DISABLED ON ON ON
Weight Mode
Pounds/Ounces OFF OFF
UPS Pounds Mode ON ON
NOTE ! Change switch settings only with power to the scale disconnected!
If changing between Pounds/Ounces and Pounds only mode, the scale must
be recalibrated.
Settings For UPS Online Users
The AS-400D and AS-410D dip switches must be set as follows to work with UPS OnLine
software. Set scale type to Fairbanks 70-2453-4 in the UPS software.
Switch 1 2 3 4 5
Setting ON ON OFF OFF ON
• 9600 Baud
• 7 Data Bits
• Odd Parity
• 1 Stop Bit
• UPS Pounds Mode
3
NOTE! Change switch
settings only with power
to scale disconnected!
Page 6
SERIAL INTERFACE PROTOCOL
When communicating in host mode using the Detecto AS-400D and AS-410D pounds/ounces
mode or AS-420D pounds only mode (not the UPS Pounds Mode), the serial data is
transmitted and received using 8 data bits, no parity and one stop bit. The host computer
sends request to the scale in the form of ASCII or HEX characters. The following is a list of
commands that can be sent by the computer and the scale response:
COMMAND SCALE RESPONSE
^N (control N, hex 0E) Scale sends weight data continuously
^O (control O, hex 0F) Stop continuous weight data
~ (tilde, hex 7E) Weight data sent once in pounds/ounces mode
^X (control X, hex 18) Zero the scale from the PC
ESCAPE (ESC, hex 1B) Reset the scale from the PC
SCALE WEIGHT DATA STRINGS
AS-400D, AS-410D Pounds/Ounces Mode
Output Data Format: SspppbLBbww.wbOZbxccE
where:
S = ASCII STX (HEX 02)
s = weight sign (space or -)
ppp = weight lb, leading zero suppressed
b = space
LB = the text "LB"
ww.w = weigh ounces, leading zero suppressed
OZ = the text "OZ"
x = status: M = motion on scale
C = scale over capacity
cc = checksum - these two characters are the ASCII representation
of the computed checksum (HEX 3x, HEX 3x where xx is the
exclusive-or of all data from the STX to the status character)
E = ASCII ETX (HEX 03)
AS-420D Pounds ONLY Mode
Output Data Format: swwwww.wxccE (12 bytes total)
where:
s = weight sign (space or “-”)
wwwww.w = weight (lb and 1/10 lb including decimal point)
x = status: M = motion on scale
C = scale is over capacity
cc = checksum (ASCII representation of computed checksum)
E = ASCII ETX (03H)
4
Page 7
CALIBRATION
The AS-400D series scale was calibrated at the factory during final inspection and should not
require adjustment. In the event the scale should need re-calibration, the following calibration
procedure should be performed. To maintain the scale’s high degree of accuracy, it is
recommended that a qualified technician with certified test weights re-calibrate the scale.
Before beginning calibration, the following equipment is required:
• Calibrated test weights (50 lbs)
• No. 1 Phillips and 3/16 or 1/4 slotted screwdriver
To Calibrate The Scale:
1. Unplug the scale from the power outlet.
2. Remove the stainless steel platform.
3. Once the platform has been removed, locate the calibration jumper J12 on the main
circuit board. NOTE! On the AS-400D, locate the calibration seal (plastic cover) and
remove the cover by removing the two (2) small slotted screws on the bottom of the
scale. This will expose the calibration jumper J12.
4. Remove the jumper by pulling upwards.
5. Replace the scale platform onto the scale.
6. Plug in the power cord.
7. After the power-up sequence, the display should appear blank.
8. Press and hold the ZERO switch on the front of the scale base until /2$G is displayed.
9. Place a 50-pound weight onto the platform and press the ZERO switch.
10. Wait until 8Q/2$G appears on the display, then remove the weight.
11. Press the ZERO switch and wait until the display shows G2Q(.
12. Unplug the scale from the power outlet, and then remove the scale platform.
13. Replace the jumper onto J12.
14. Replace the scale platform, and then plug in the power cord. This will reset and restart
the scale for normal operation.
NOTE! If changing from Pounds to Pounds/Ounces mode or from
Pounds/Ounces to Pounds mode, the scale must
Zeroing The Scale
be recalibrated.
To force the scale to a zero () weight reading at any time, press the ZERO switch. If the
zero () could not be executed, check for one of the following reasons:
• There was motion present on the scale at the time.
• The scale was in an over-capacity condition
• DO NOT subject the scale platform to sudden shocks or impact.
• DO NOT expose to direct sunlight or temperature extremes or any rapidly moving air
source.
• DO NOT use acetone or other volatile solvents for cleaning the scale.
• DO NOT submerge the scale in water, pour or spray water directly on it.
• DO clean the scale with a soft cloth dampened with a mild detergent.
• DO provide good, safe ground and clean AC power.
• DO keep the area around the scale clear to provide adequate air circulation.
CARE AND MAINTENANCE
5
Page 8
6
Loading...