Capresso Impressa Z5, Impressa Z6 Quick Reference Manual
Impressa
Z5/Z6
Quick
Reference
Guide
This Guide does not replace the Operating Instructions.
For details and cautions you must read all instructions.
Watch the DVD instructions!
Traces of Coffee Grounds in New Machine?
This is normal! Grinder was tested during assembly with
beans. Despite cleaning, traces of ground coffee may
be found.
RED TEXT represents display text. Illustration numbers
on next page correspond with Operating Instructions.
A) First Time Ever Preparation
1. Fill water in tank, open Cover Lid (spring activated!),
remove Bean Container Safety Lid and add beans.
Only regular beans, no flavor
ed or coated beans
!!!
Replace Bean Container Safety Lid (Fig. 4).
2. DO NOT install the Clearyl Filter Cartridge now!
3. Turn the Main Power Switch on (bottom left by cord).
4. Push On/Off button on top (Fig. 3). Place a large cup
under the Hot Water Spout / Coffee Spouts and one
under the Auto Cappuccino System (ACS) (Fig. 5e).
PRESS RINSE. Push the Rinse button. SYSTEM
FILLS, then WELCOME TO JURA then UNIT IS
HEATING
then PRESS RINSE. Press the Rinse
Button. COFFEE READY.
5. Leave the cup under the coffee spouts and push the
1-cup Espresso Button. FILL BEANS. Push the
1-cup Espresso Button again. Wait until the Z5/Z6
displays
COFFEE READY. Discard the coffee.
6. Your next cup will be perfect.
B) Daily Preparation
• Fill fresh water in tank and check bean container.
• Push On/Off button (Fig. 3).
MACHINE IS HEATING
then RINSE. Place a cup under the coffee spouts
and press the Rinse Button.
COFFEE READY.
C) Installing the Auto Cappuccino System (ACS)
• Attach the Dial Component to the Dual Fixed Spouts.
(Fig. 5c)
65351R2
Bean
container
safety lid
Lid for
ground
coffee
Grind
selector
Fig. 5c
Fig. 5d
Fig. 5e
Gap
Coffee
Nozzle
Milk
Nozzle
Fig. 5f
Milk & Froth
(Cappuccino)
Milk only
(Latte)
Steam only
(Rinsing)
Fig. 3
Milk
C
appuccino
L
atte
S
pecial
C
offee
H
ot
W
ater
1
-Cup 2-Cup 1-Cup 2-Cup
Espresso Coffee
On/Off
Rotary
Dial
R
inse
COFFEE READY
Fig. 4
ACS
Cover
lid
Venting tip
• Then attach the long Dual Nozzle System to the
Dial component (Fig. 5d). Please note: The milk nozzle
should sit tight. The coffee nozzle must have a gap
(Fig. 5e). Make sure the dial points to the cup with
saucer for cappuccino (Fig. 5f).
• Attach the long hose to the dial component and
insert the other end into a milk carton.
Thermal Milk Container: If you use the thermal milk
container, attach the straight rod to the lid with the
tapered end pointing to the bottom. Then insert the elbow
rod through the top of the lid into the straight rod. Slip the
open end of the short flexible hose over the elbow rod.
Fill the thermal container with cold milk and assemble lid,
thermal container and dial component.
Important: Cold
milk will stay cold for about 8 hours in the thermal milk
container. Then the milk must be returned to the refrigerator
or discarded. Remove lid when refrigerating. Rinse hoses
and thermal container with hot water.
D) Eight Beverage Buttons
The Milk, Cappuccino and Special Coffee button brew
through the ACS System (Fig. 5e). The Hot Water button
brews through the hot water spout.
The beverage buttons are pre-set as follows:
Coffee Coffee
Button Function Milk Volume Strength
Milk 20 sec – –
Cappuccino/Latte * 15 sec 3.0 oz NORMAL
Special Coffee * – 3.0 oz. XSTRONG
Hot Water – 6.0 oz. –
1 Espresso * – 1.5 oz. STRONG
2 Espresso * – 3.0 oz. STRONG
1 Coffee * – 5.0 oz. NORMAL
2 Coffee * – 10.0 oz. NORMAL
* Temperature for coffee is set at HIGH.
• You can override Coffee Strengths just before brewing.
• You can override Cup Size during brewing.
• Overriding (chapter M) will not change above pre-sets.
• All pre-sets can be changed to new pre-sets (chapter N)
Important: You can always stop any brewing by pushing
the Rotary Dial or any beverage button.
Impor
tant:
Never tr
y to pull out the drawer while the
Z5/Z6 is br
ewing or discar
ding. Always wait until the cycle
is completed and the display shows
COFFEE READY.
Loading...