Canon VIXIA HF11, VIXIA HG20, VIXIA HG21 INSTRUCTION MANUAL

Page 1
Digital Video Software
Instruction Manual
Version 31
COPY
English
Page 2
Contents
Checking Supplied Accessories ............................................................................ 4
System Requirements ............................................................................................... 5
What is Digital Video Software? ............................................................................... 6
CameraWindow ..................................................................................................... 7
[Acquire Images] Tab ........................................................................................ 7
[Print] Tab .......................................................................................................... 8
[Set to Camera] Tab .......................................................................................... 9
Camera Browser Window ............................................................................... 10
Browser Window...................................................................................................11
[Image Viewer] Window ....................................................................................... 15
[Trim Image] Window ...................................................................................... 16
[Color/Brightness Adjustment] Window ........................................................... 16
[Red Eye Correction] Window ......................................................................... 17
[Insert Text] Window ........................................................................................ 17
[Level Adjustment] Window ............................................................................. 18
[Tone Curve Adjustment] Window ................................................................... 18
[Sharpness] Window ....................................................................................... 19
[Auto Adjustment] Window .............................................................................. 19
Installing the Digital Video Software ...................................................................... 20
Before Downloading Still Images ........................................................................... 23
Connecting the Camcorder to a Computer .......................................................... 23
Settings on the camcorder .............................................................................. 23
Connecting the camcorder .............................................................................. 24
Downloading Still Images........................................................................................ 25
Using the Computer to Download Still Images (CameraWindow) ....................... 26
Auto-downloading ........................................................................................... 26
Applying Auto-downloading Settings .............................................................. 27
Downloading the Selected Still Images from the CameraWindow .................. 30
Using the Camcorder to Download Still Images (Direct Transfer Function) ........ 32
Setting the Direct Transfer Download Destination Folder ............................... 32
Direct Transfer ................................................................................................ 33
Using a Card Reader/Writer ................................................................................ 34
Auto-downloading ........................................................................................... 35
Applying Auto-downloading Settings .............................................................. 35
Downloading the Selected Still Images from the ImageBrowser .................... 36
Printing Still Images................................................................................................. 38
Printing Still Images without Downloading Them................................................. 38
Printing Still Images Already Downloaded to the Computer ................................ 43
[Photo Print] .................................................................................................... 43
[Index Print] ..................................................................................................... 45
[Layout Print] ................................................................................................... 47
Organizing Images................................................................................................... 49
Applying Star Rating ............................................................................................ 49
Specifying the Keywords...................................................................................... 50
Classifying the Images......................................................................................... 51
Sort by the Shooting Date ............................................................................... 51
Sort by the Star Rating .................................................................................... 52
COPY
2
Contents
Page 3
Renaming Multiple Files ...................................................................................... 54
Searching for Images........................................................................................... 55
Exporting Images ..................................................................................................... 57
Changing the File Type and Saving..................................................................... 57
Uploading Still Images to the camcorder ............................................................. 60
Using Various Functions ......................................................................................... 62
Attaching Images to E-mail Messages ................................................................ 62
Running a Slide Show ......................................................................................... 64
Adding Sound to a Still Image.............................................................................. 65
Reviewing and Changing the Owner Name of the Camcorder............................ 66
Uninstalling the Software ........................................................................................ 67
Uninstalling ImageBrowser .................................................................................. 67
Troubleshooting ....................................................................................................... 68
COPY
Macintosh
Contents
3
Page 4
Read This First
Disclaimer
• While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. Canon reserves the right to change the specifications of the hardware and software described herein at any time without prior notice.
• No part of this guide may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, by any means, without the prior written permission of Canon.
• Canon makes no warranties for damages resulting from corrupted or lost data due to mistaken operation or malfunction of the camcorder, the software, memory cards (SD, SDHC and miniSD Cards), personal computers, or peripheral devices, or due to use of a memory card not initialized by a Canon camcorder.
Trademark Acknowledgments
• Macintosh, Mac OS and iPhoto are trademarks of Apple Inc., registered in the U.S. and other countries.
• miniSD™ is a trademark of SD Card Association.
• The SD logo is a trademark. The SDHC logo is a trademark.
• Intel is a trademark or a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
• Other names and products not mentioned above may be registered trademarks or trademarks of their respective companies.
© Canon Inc. 2008 All rights reserved.
Safety Precautions
Do not play the supplied CD-ROM(s) in any CD player that does not support data CD-ROMs. Playing the CD-ROM(s) in an audio CD player (music player) could damage the speakers. It is also possible to suffer from hearing loss from listening with headphones to the loud sounds of a CD-ROM played on a music CD player.
COPY
Checking Supplied Accessories
Use the following accessories to download recorded still images from the camcorder to your computer.
• Supplied USB cable The cable supplied with your camcorder may be different from the one described in this manual.
• DIGITAL VIDEO Solution Disk
4
The explanations in this manual use mainly Mac OS X version 10.3 screen shots. The steps and windows may vary depending on your computer.
Read This First
Page 5
System Requirements
OS: Mac OS X (v10.3 - v10.5) Computer Model: Computers that come with above OS preinstalled CPU: PowerPC G3/G4/G5, or Intel processor RAM: 256 MB or more Interface: USB Free Hard Disk Space: Canon Utilities
- ImageBrowser 300 MB or more
Display: 1024
Proper operation is not guaranteed on any particular system, even if it meets
the requirements outlined above.
ImageBrowser does not operate on disks initialized with the Unix File
System (UFS).
A CD-ROM drive is required to install the software.
× 768 pixels/32,000 colors or better
COPY
Macintosh
System Requirements
5
Page 6
What is Digital Video Software?
Digital Video Software allows you to download still images you recorded with the camcorder to a computer and manage, print, and edit them.
ImageBrowser
• Viewing still images as thumbnails
• Managing by shooting date folders with still images
• Categorizing, organizing, and searching large volumes of still images
• Printing still images
• Editing still images
• Changing the data for still images and save them as new files
• Attaching still images to e-mail
• Viewing still images in a slide show
• Adding sound to a still image
CameraWindow
• Downloading still images to your computer
• Viewing still images directly from the camcorder, without downloading them
• Printing still images directly from the camcorder, without downloading them to the computer
This instruction manual explains how to install the software, what you can do with the main features and how to operate them. For more detailed operational instructions, refer to the Help menu of each software program.
Your camcorder may not support some features of the software.
COPY
6
What is Digital Video Software?
Page 7
Windows
CameraWindow
After you connect the camcorder to your computer, you can use CameraWindow to download still images to the computer. Furthermore, you can print still images directly from the camcorder, without having to download them to the computer ( 38), and you can confirm and change the owner’s name of the camcorder you specify ( 66). Refer to Using the Computer to Download Still Images (CameraWindow) ( 26) for launching the software. The Remote capture function is not supported by the camcorder.
Click the [CameraWindow] icon in the Dock (bar appearing at the bottom of
the desktop) if the Camera Control window does not appear.
When the [CameraWindow] icon is not in the Dock, double click the [Canon
Utilities] folder on the drive where the program was installed, followed by the [CameraWindow] folder and the [CameraWindow] icon.
[Acquire Images] Tab
After you connect the camcorder to your computer, use this tab to download still images to the computer.
Camera Control window
Selects a function in the Camera Control window.
COPY
Macintosh
Specify the image type to be downloaded and the destination folder.
Images in the camcorder are displayed allowing you to select images.
Images will be downloaded to the computer, and ImageBrowser starts.
Windows
7
Page 8
[Print] Tab
After connecting the camcorder to your computer, use this tab to print still images without downloading them to the computer first. The window varies depending on the selected printing type. Refer to Printing Still Images without Downloading Them (38).
Camera Control window
Prints all still images, one image per page.
Displays a list of the still images in the camcorder (built-in hard disk/memory or memory card), allowing you to select which ones to print.
Prints according to the DPOF print settings set by the camcorder.
Prints all still images as an index page (rows of images with file names and image information).
COPY
8
Windows
Page 9
[Set to Camera] Tab
This tab is used for confirming and changing the owner’s name of the camcorder you can specify ( 66) and uploading the still images to the camcorder. My Camera function is not supported by the camcorder.
Camera Control window
Uploading the images from the computer.
Enter or change the name of the camcorder’s owner.
COPY
Macintosh
Windows
9
Page 10
Camera Browser Window
Camera Browser window
Still image information and a histogram
Starts ImageBrowser.
Prints the selected still images.
Selects the still image selection method. Changes the size of the thumbnail.
If your camcorder supports wide size still image (16:9 such as 1920 x 1080 pixels) recording, the thumbnails that appear in this window will be also 16:9 images. The sample images used on this instruction manual are normal size still images (4:3).
COPY
Selects whether to show or hide the image frame and file name.
10
Windows
Page 11
Browser Window
ImageBrowser is a software program used for organizing, printing and editing the downloaded still images. To start ImageBrowser, click the [ImageBrowser] icon in the Dock. If the ImageBrowser icon is not in the Dock, double-click the [Canon Utilities] folder on the drive on which the program was installed, followed by the [ImageBrowser] folder and the [ImageBrowser] icon.
1
3
2
1 Explorer View
In the [Last Acquired Images] panel, the newly downloaded still images are placed into virtual folders classified by recording date. In the panel below, the folders that the downloaded still images are actually saved in are displayed. Selecting the [Favorite Folders] tab shows only the folders that are registered as favorites. The [All Folders] tab shows all available folders. indicates that newly downloaded still images are in the folder. Clicking the triangle symbol besides the folder name displays/hides the folder contents. To register a folder as Favorites, follow the instructions below.
When you have selected the [Favorite Folders] tab:
Click [Add] and specify a folder.
When you have selected the [All Folders] tab:
Select a folder and click [Add to Favorites].
To remove the registered folder, select the folder, and click [Remove].
COPY
2Browser Area
4
5
Macintosh
This area displays the images contained in the selected folder.
Windows
11
Page 12
3 View Mode
You can select a view mode of images in the Browser Area. [Preview Mode]: The thumbnails are displayed at the bottom of the Browser Area,
and the Information Panel is displayed in the upper part.
Preview Image
Information Panel
Selected Thumbnail
[List Mode]: The images are displayed as thumbnails. The thumbnails can be enlarged/reduced by selecting [Enlarge] or [Reduce] from the [View] menu.
Context Menu
When you click on a thumbnail while pressing the [control] key on the keyboard, a context menu will appear. The context menu allows you to select several functions directly without using the menu bar located on top of the window.
COPY
Context menu
12
Windows
Page 13
[File Information]
When the view mode is set to [List Mode], select [Get Info] from the [File] menu to display the following window.
You can rename files.
Hides the information display at the right.
Input a comment.
Shooting information
Sets a star rating.
You can switch and view the shooting information of the next or previous image by clicking these buttons.
Placing a check mark here prevents the image from being overwritten or deleted.
You can play sounds if they are attached to images.
COPY
Histogram
Sets a keyword.
Macintosh
Windows
13
Page 14
4 Image display control panel
1
1 Filter Tool Allows you to select which still images to display
according to the star rating. When you download the images, the star rating is set to two stars as a default. To change the star rating, refer to Applying Star Rating ( 49).
2
Enlarge/Reduce Enlarges/Reduces the thumbnails in the Browser Window.
3
Selecting Images Allows you to select all images and deselects images.
4
Display Pattern Allows you to change the appearance of the Browser
Window.
32
4
5 Control panel
1
2
3 4 5
1Canon Camera Opens CameraWindow.
2
View Image Displays a selected image in the [Image Viewer] window.
3
SlideShow Displays still images in a slide show.
4
Print & Email After you download still images to a computer, use this to
print them or to attach them to e-mail messages.
COPY
5
Send to Trash Deletes the selected images.
14
Windows
Page 15
[Image Viewer] Window
The [Image Viewer] window appears when you select an image and click [View Image] or double click an image.
Changes the zoom ratio of the image.
3 4
2
1 Back/Next Displays the previous/next image in the current folder.
2
Save Allows saving the edited image.
3
Edit Allows you to perform the following operations: red-eye
correction, auto correct, color and brightness correction, sharpness adjustment, trimming, inserting text, or registering external image editing applications. Unable to use when the multiple images are selected.
4
Number of Displays
5
Synchronize Synchronizes View functions across all displayed images.
6
Full Screen Displays an image in full screen size. To return to Browser
Allows you to display multiple images at the same time.
COPY
Window, click the full screen sized image or press any key.
5
617 8
Changes the star rating.
7
Print Prints the selected still image. Refer to [Photo Print]
( 43).
8
Show Shooting Information
The shooting information of the image will be displayed. [Show AF Frame] cannot be used for the images recorded by the camcorder.
Windows
Macintosh
15
Page 16
[Trim Image] Window
Select [Trim Image] from the icon located at the bottom of the [Image Viewer]
window. Specify the area in the still image to crop and click [Trim Image] to trim the
image.
[Color/Brightness Adjustment] Window
Select [Color/Brightness Adjustment] from the icon located at the bottom of
the [Image Viewer] window. Use this to change the image’s properties by adjusting
the RGB intensity, saturation and brightness.
COPY
16
Windows
Page 17
[Red Eye Correction] Window
Select [Red Eye Correction] from the icon located at the bottom of the [Image
Viewer] window. Use this to correct still images in which people’s eyes appear red.
[Insert Text] Window
Select [Insert Text] from the icon located at the bottom of the [Image Viewer]
window. Use this to write text on still images.
COPY
Windows
Macintosh
17
Page 18
[Level Adjustment] Window
Select [Level Adjustment] from the icon located at the bottom of the [Image
Viewer] window. Use this to adjust the levels in a still image to change its
appearance.
[Tone Curve Adjustment] Window
Select [Tone Curve Adjustment] from the icon located at the bottom of the
[Image Viewer] window. Use this to adjust the tone curve for a still image to change
its appearance.
COPY
18
Windows
Page 19
[Sharpness] Window
Select [Sharpness] from the icon located at the bottom of the [Image Viewer]
window. Use this to emphasize and clarify the outlines of people and objects.
[Auto Adjustment] Window
Select [Auto Adjustment] from the icon located at the bottom of the [Image
Viewer] window. Use this to automatically correct the color balance of the still
image.
COPY
Macintosh
Windows
19
Page 20
Installing the Digital Video Software
Before you connect the camcorder to the computer with the USB cable for the first time, you must install the Digital Video Software.
Your digital video camcorder is equipped with the standard Picture Transfer Protocol (PTP). This protocol enables you to download still images by simply connecting the camcorder to a computer with the USB cable (using software such as iPhoto or Image Capture preinstalled on Mac OS X). However, note that there are several limitations to downloading still images with this method.
It may take a few minutes, after connecting the camcorder, until you can
download still images.
Still images protected on the camcorder may lose this setting once they are
downloaded to the computer.
When downloading the still images by Image Capture that comes with Mac
OS, the Exif version may change to 2.1 and image information may be modified. Either install ImageBrowser to download the still images or use the following procedure.
1) Connect the camcorder to the computer, and start Image Capture.
2) Click [Options].
3) Remove the checkmark from [Embed Colorsync profile] in the [Download Options] tab and click [OK].
1
Close all programs that are running, and check that the camcorder is not connected to the computer.
2
Set the DIGITAL VIDEO Solution Disk in the computer’s CD-ROM drive.
3
Double click the CD-ROM icon and the [Canon Digital Video Installer] icon.
COPY
20
Installing the Digital Video Software
Page 21
4
Click [Install] under Digital Video Software.
Installer Panel
5
Select [Easy Installation] and click [Next].
To install the software individually, select [Custom Installation].
COPY
When installing the software by selecting [Easy Installation], EOS Utility (software for downloading still images from the Canon EOS Digital SLR Cameras) will be installed. This software is used only for compatible Canon EOS Digital SLR Cameras, and the camcorder does not support this software.
6
Read the license agreement and click [Agree] to accept the terms.
Macintosh
Installing the Digital Video Software
21
Page 22
7
Review the installation settings and click [Next].
8
When the “Installation has finished.” message appears, click [Finish].
After the installation is complete, restart the computer as prompted.
COPY
9
Remove the DIGITAL VIDEO Solution Disk from the CD-ROM drive.
When installation is complete, remove the DIGITAL VIDEO Solution Disk before you connect the camcorder to the computer.
22
Installing the Digital Video Software
Page 23
Before Downloading Still Images
Connecting the Camcorder to a Computer
Be sure to install the Digital Video Software before you connect the
camcorder to the computer.
Make sure the camcorder is being powered using the power adapter before
connecting it to a computer.
Connect the USB cable directly to one of the computer’s main USB ports.
The interface may not function correctly if the camcorder is connected via a USB hub.
The connection may not operate correctly if you are using other USB
devices, excluding USB mice or keyboards, at the same time. If this occurs, disconnect the other devices from the computer and try reconnecting the camcorder.
Do not connect two or more camcorders to the same computer via the USB
interface. The connections may not operate correctly.
Never allow the computer to go into standby (sleep) mode while a
camcorder is connected via the USB interface.
Refer to your computer manual for the location of the computer’s USB ports. For details about changing settings on the camcorder and connecting the
camcorder to the computer, see the camcorder’s instruction manual.
Settings on the camcorder
Before connecting the camcorder to the computer, change the following camcorder settings in advance.
• In the still images index screen, select which still images to play back (built-in hard disk/memory or memory card).
• In the [SYSTEM SETUP] menu, set [USB SETTING] to one of the following options.
- [PC/PRINTER]:
To simply connect the camcorder to the computer without further operations.
- [CONNECT&SET]:
Select [PC/PRINTER] on the camcorder every time you connect it to a computer.
COPY
Macintosh
Before Downloading Still Images
23
Page 24
Connecting the camcorder
1
Connect the compact power adapter to the camcorder.
2
If downloading images from a memory card, insert the memory card into the camcorder.
3
Set the camcorder to still image playback mode.
Wait until the ACCESS indicator stops flashing.
4
Attach the supplied USB cable to the computer’s USB port and the camcorder’s USB Terminal.
USB Terminal on the Camcorder
USB Cable
Camcorder End Computer End
USB Port on the Computer
COPY
24
Before Downloading Still Images
Page 25
Downloading Still Images
Below explains the procedure for connecting a camcorder to a computer using the USB cable. For connecting a card reader/writer, see Using a Card Reader/Writer (34).
You cannot connect the camcorder to a computer if the built-in hard disk/
memory or the memory card contains 1,800 images or more. In such case, copy the images in the built-in hard disk/memory to a memory card and then use a card reader/writer to download the images to the computer.
You may not be able to download images with ImageBrowser or OS
standard software (depending on the computer you are using and the installed OS) if the built-in hard disk/memory or the memory card contains more than approximately 1000 images. In such case, copy the images in the built-in hard disk/memory to a memory card and then use a card reader/ writer to download the images to the computer.
Observe the following precautions when the camcorder’s access indicator is
flashing. Failure to do so may cause data to become corrupted.
- Do not remove the memory card or detach the USB cable.
- Do not turn off the camcorder or the computer.
- Do not change the position of the mode dial.
The still images you recorded and/or downloaded to the hard disk are
important original data files. Create a copy of the file first before working on it on your computer.
COPY
Macintosh
Downloading Still Images
25
Page 26
Using the Computer to Download Still Images (CameraWindow)
You can select a downloading method in the Camera Control window.
Auto-downloading
1
Connect the camcorder to the computer ( 23).
• The Camera Control window will be displayed. If it does not appear automatically, click the [CameraWindow] icon in the Dock (the bar at the bottom of the desktop).
• If you do not wish the Camera Control window to open automatically when you connect the camcorder, click the [File] menu and clear the check mark from the [Displays this screen when the camera is connected].
2
Click [Starts to download images].
Click [Exit] to close the Camera Control window after downloading images.
Camera Control window
COPY
26
Downloading Still Images
Page 27
Applying Auto-downloading Settings
This task allows you to apply auto-downloading settings. You can specify the types of still images and the destination folder.
1
In the Camera Control window, click the [Acquire Images] tab and click [Preferences].
2
Select [Change auto download settings] and click [Next].
COPY
Macintosh
Downloading Still Images
27
Page 28
3
Select the image type to be downloaded and click [Next].
Place a check mark here if you wish the original image to be deleted after downloading.
4
Specify the destination folder settings and click [Next].
Destination Folder
Click this button to browse where you want to save the images.
Select to specify the name of the subfolder.
COPY
28
Downloading Still Images
Page 29
5
Specify a process to perform after the image is downloaded and click [Next].
The window below will be displayed when you select [Perform selected processes consecutively] (you can redisplay the window by clicking [Select]). Select a process to perform after the image is downloaded, and click [OK].
6
Click [Finish].
Placing a check mark here makes images in the camcorder to be automatically downloaded when the camcorder is connected.
COPY
Macintosh
Downloading Still Images
29
Page 30
A
Downloading the Selected Still Images from the CameraWindow
1
Click [Lets you select and download images].
Select images you wish to download and click [Download
2
Images].
• Clicking on 2 images while holding down the [option] + [shift] key selects also all images between the 2 images.
• Clicking on different images while holding down the [shift] key selects multiple images.
blue frame appears
around the selected image.
COPY
30
Downloading Still Images
Page 31
3
Confirm the settings and click [Start Download].
• ImageBrowser starts, and Browser Window appears.
Settings for the folder and the subfolder for downloaded images
Settings for the file prefix and the consecutive numbers
• To make changes, click [Change Settings].
[Specify Folder] Tab
Specify the settings of the folder and subfolder.
[Specify File Name] Tab
COPY
Specify the file name with which to save the images.
Macintosh
Downloading Still Images
31
Page 32
Using the Camcorder to Download Still Images (Direct Transfer Function)
If your camcorder supports the Direct Transfer function, you can use the camcorder to download images.
Setting the Direct Transfer Download Destination Folder
1
Click the [Acquire Images] tab and click [Preferences].
Click [Exit] to close the Camera Control window.
2
Select [Change direct transfer download destination folder] and click [Next].
COPY
32
Downloading Still Images
Page 33
3
Specify the destination folder settings and click [Finish].
Destination Folder
Click this button to specify the destination folder.
Select to specify the name of the subfolder.
Direct Transfer
1
Select a transfer option on the camcorder screen and press the button.
• See your camcorder instruction manual for how to set and operate the camcorder to transfer images.
• The button cannot be used when it is not lighted.
COPY
Macintosh
Downloading Still Images
33
Page 34
Using a Card Reader/Writer
Select a download method in the image download window. The basic operations are the same as when you connect the camcorder to the computer. Follow the procedure below to open the CameraWindow. For instructions on how to connect the card reader/writer, refer to its manual.
If you are using a camcorder that supports miniSD cards but your card reader/ writer does not support them, please purchase an appropriate adapter for your card. If you are using SDHC cards, you need to use a card reader/writer compatible with SDHC cards.
1
Insert a memory card containing images recorded with the camcorder into the card reader/writer and connect it to the computer.
2
Select a method to download the images.
• [Download Images]: A progress bar will be displayed and images will be downloaded to the computer, and ImageBrowser starts. To apply auto­downloading settings, refer to Applying Auto-downloading Settings (35).
• [Lets you select and download images]: The ImageBrowser opens, displaying the still images on the memory card as thumbnails (small images).
COPY
34
Downloading Still Images
Page 35
Auto-downloading
1
Click [Download Images].
Click [Exit] to close the window after downloading images.
Applying Auto-downloading Settings
This task allows you to apply auto-downloading settings. You can specify the types of still images and the destination folder.
1
Click [Preferences].
COPY
Macintosh
Downloading Still Images
35
Page 36
2
Configure the settings and click [OK].
Downloading the Selected Still Images from the
ImageBrowser
1
Click [Lets you select and download images].
COPY
36
Downloading Still Images
Page 37
2
Select images you wish to download and click [Download Images].
• Clicking on 2 images while holding down the [option] + [shift] key selects also all images between the 2 images.
• Clicking on different images while holding down the [shift] key selects multiple images.
A blue frame appears around the selected image.
COPY
Macintosh
Downloading Still Images
37
Page 38
Printing Still Images
Printing Still Images without Downloading Them
This section explains how to print still images by connecting the camcorder to the computer. The steps are basically the same when using a card reader/writer. You can select one of the following 4 methods to print still images directly from the camcorder, without downloading images to the computer.
• [Print All Photos]
- Prints all still images, one image per page.
• [Print Contact Sheet with All Photos]
- Prints all still images as an index (rows of images with file names and image information).
• [Print according to DPOF settings]
- Prints according to the DPOF print settings set by the camcorder.
• [Select image and print]
- A list of the still images will be displayed, and you can select the images you wish to print.
1
Connect the camcorder to the computer. ( 23)
2
Click the [Print] tab in the Camera Control window.
COPY
38
Printing Still Images
Page 39
3
Click on one of the 4 printing methods.
4
Specify the print settings and click [Print].
The window varies depending on the selected printing method in step 3.
COPY
Macintosh
Printing Still Images
39
Page 40
When you have selected [Print All Photos]:
Selects the printer.
Sets the paper size settings.
Sets the shooting date/time imprint and color settings.
COPY
Sets the number of print copies of the displayed image.
Click this button to switch between still images if multiple images are selected.
40
Printing Still Images
Page 41
When you have selected [Print Contact Sheet with All Photos]:
Sets the printer and paper size settings.
Selects the printer.
Click these buttons to switch between pages.
Sets the print settings for shooting information, comments, headers, footers and page numbers.
Sets the number of rows and columns.
Sets the number of print copies of the contact sheets.
When you have selected [Print according to DPOF settings]:
• The selected still images will be printed according to the number of copies set with the camcorder. The same window described in the previous section When you have selected [Print All Photos]: (40) will be displayed.
COPY
Click this to use the trimming function (crops a portion of the still image).
Rotates still images.
Macintosh
Printing Still Images
41
Page 42
When you have selected [Select image and print]:
• If you selected [Select image and print], the following window will be displayed. Select still images you wish to print, and click [Print]. If you selected [Contact Sheet Print], the same window described in the previous section When you have selected [Print Contact Sheet with All Photos]: ( 41) will be displayed. If you selected [One Photo Per Page Print], the same window described in the previous section When you have selected [Print All Photos]: ( 40) will be displayed instead. Set the print settings and print the still images.
COPY
5
When the print window opens, click [Print].
6
When the printing finishes, click to close the window.
42
Printing Still Images
Page 43
Printing Still Images Already Downloaded to the Computer
You can select one of the following 3 methods to print still images downloaded to the computer.
• [Photo Print]
- Prints one still image per page.
• [Index Print]
- Prints selected images in rows with file names and image information.
• [Layout Print]
- Allows you to lay out the selected still images in special arrangements and add text
and decorations, printing them as one page in a fancy album.
[Photo Print]
1
Select the still images you wish to print and click [Print & Email] [Photo Print] from the displayed menu.
COPY
Macintosh
Printing Still Images
43
Page 44
2
p
Specify the print settings and click [Print].
Selects the printer.
Sets the paper settings.
Sets the shooting date/time imprint and color settings.
COPY
Sets the number of print copies of the displayed image.
Click this button to switch between still images if multi
le images are selected.
44
Printing Still Images
Page 45
3
When the print window opens, click [Print].
4
When the printing finishes, click to close the window.
[Index Print]
1
Select still images you wish to print and click [Print & Email] [Index Print] from the displayed menu.
COPY
Macintosh
Printing Still Images
45
Page 46
2
Specify the print settings and click [Print].
Sets the paper size and orientation.
Selects the printer.
Click these buttons to switch between pages.
Sets the print settings for shooting information, comments, headers, footers and page numbers.
Sets the number of rows and columns.
Sets the number of print copies of the contact sheets.
3
When the print window opens, click [Print].
4
When the printing finishes, click to close the window.
COPY
Click this to use the trimming function (crops a portion of the still image).
Rotates still images.
46
Printing Still Images
Page 47
[Layout Print]
• You can select one of the following 3 layout print methods.
- [Custom layout printing]:
Allows you to specify the size and location of the still images freely.
- [Fixed photo size printing]:
Allows you to specify the size of the all still images.
- [Tiled photo printing]:
Allows you to have the program lay out and print the specified number of images per page with no gaps between still images on the page.
• Selecting [Edit] [Add Text] allows you to write some text on a still image. You can move added text boxes on the still image by dragging them.
• Selecting [Edit] [Edit Header] allows you to insert a header.
Select still images you wish to print and click [Print & Email]
1
[Layout Print].
COPY
Macintosh
Printing Still Images
47
Page 48
2
Select a print style from the pull-down menu and click [Print] after specifying the print settings.
3
When the print window opens, click [Print].
4
When the printing finishes, click to close the window.
COPY
48
Printing Still Images
Page 49
Organizing Images
Applying Star Rating
• This task allows you to apply ratings to your images from one star to three stars. The star rating can be used as one of the search conditions, or for the selection of images to be displayed in the Browser Window.
• The default setting of the star rating is two stars.
1
Select the image to which you wish to apply the Star Rating.
2
Select [Change Star Rating] from the [Edit] menu.
The default setting of the star rating is two stars.
COPY
Macintosh
Organizing Images
49
Page 50
Specifying the Keywords
You can use keywords when searching for images.
1
Select an image to which you wish to apply the keyword.
2
Select [Keyword] [Settings] from the [Edit] menu.
3
Place a check mark next to the keyword you wish to apply and click [OK].
COPY
You can add and delete keywords, or change the keyword list in the [Manage Keywords] window by selecting [Keyword] [Manage] from the [Edit] menu.
50
Organizing Images
Page 51
Classifying the Images
This task allows you to sort images into a folder according to the shooting date or star rating.
Sort by the Shooting Date
1
Select the images you wish to classify and select [Organize Image] [Sort Images] from the [File] menu.
2
Select [The files will be separated into folders for each shooting date.] and click [Next].
COPY
Macintosh
Organizing Images
51
Page 52
3
Specify the sort settings and click [OK].
The selected images are classified into the specific folder.
Sort by the Star Rating
1
Select the images you wish to classify and select [Organize Image] [Sort Images] from the [File] menu.
COPY
52
Organizing Images
Page 53
2
Select [The files will be organized by Star Rating.] and click [Next].
3
Specify the sort settings and click [OK].
COPY
Macintosh
Organizing Images
53
Page 54
Renaming Multiple Files
This task allows you to rename multiple files at the same time, or to rename and copy multiple files.
1
Select the images you wish to rename and select [Organize Image] [Rename] from the [File] menu.
2
Specify the settings and click [OK].
The images are renamed according to the settings specified.
Placing a check mark here makes copies of images with new names. The name of the original images will not be changed.
COPY
54
Organizing Images
Page 55
Searching for Images
This task allows you to search for images by star rating, modification date, shooting date, comment or keywords.
1
Select a folder in the explorer view.
2
Select [Search] from the [File] menu.
3
Specify the search conditions and click [Search Now].
• The search results are displayed as thumbnails.
• Select at least one search condition.
• Clicking the icon discloses the parameters of settings.
Clicking this button allows you to specify a folder.
COPY
Macintosh
Organizing Images
55
Page 56
4
Click [Finish].
• To change the search parameters and perform another search, click [Back] and repeat steps 3-4.
• The images of the search result are displayed in the [Search Results] folder. You can print or copy these images to another folder.
Explorer View
COPY
The searched images will remain in this folder until ImageBrowser is closed or another search is performed, but if you delete an image in this folder, the corresponding original image will be deleted as well.
56
Organizing Images
Page 57
Exporting Images
Changing the File Type and Saving
This task allows you to change the size, resolution or data of selected still images and save them as new files and allows saving the shooting properties of the still image to a text file or copying the still images with new names. Furthermore, you can export still images for use as a screen saver or a wallpaper.
1
Select an image you wish to export and [Export Image] from the [File] menu.
Select exporting type and click [Next].
2
COPY
Macintosh
Exporting Images
57
Page 58
3
Specify the export settings and click [Finish].
The window varies depending on the selected export type in step 2.
When you have selected [Edit and Save Image]:
You can convert still images to another file type, resize and save them as new files. You can select the file type from BMP, PICT, JPEG and TIFF. You can also specify a prefix to be added to the exported still images.
When you have selected [Export Shooting Properties]:
You can select information you wish to export and save as a text file.
COPY
58
Exporting Images
Page 59
When you have selected [Export as a Screensaver]:
You can export and save the image as a screen saver.
When you have selected [Export an Image as Wallpaper]:
You can export and save the image as a desktop wallpaper. This task cannot be performed if you have selected multiple images.
COPY
Macintosh
Exporting Images
59
Page 60
Uploading Still Images to the camcorder
You can copy still images saved on the computer to the camcorder.
1
Connect the camcorder to the computer ( 23).
The still images will be added to the memory selected for the playback of still images (built-in hard disk/memory or memory card).
2
Click the [Set to Camera] tab in the Camera Control window, and [Uploads images to the camera].
3
Select the still image you wish to add and click [Open].
You can check the selected image by clicking the file name.
COPY
60
Exporting Images
Page 61
4
In the Add image window, select the image size and click [Add].
• The selected images will be recorded to the memory card.
• When recording is complete, the images will appear in the CameraWindow.
COPY
Macintosh
Exporting Images
61
Page 62
Using Various Functions
Attaching Images to E-mail Messages
You can attach selected images to an e-mail message. If necessary, you can make the image file size smaller.
1
Select the images you wish to send in the Browser Area.
2
From the [Internet] menu, select [Create Image for Email].
3
Specify the image size and click [Finish].
COPY
62
Using Various Functions
Page 63
• If you select [Using custom settings.], change the settings in [Custom Settings] and click [OK].
• The image will be saved to the [Email Images] folder in the explorer view section.
Explorer View
Note that some e-mail software may not start automatically. For details, refer
to the Help menu of the OS you are using.
You can also set the e-mail software that starts automatically after the image
is created. To do so, click the [Applications] folder on the drive where the OS was installed and then double click the [Mail] icon. Next, in Mail preferences, click [General] and then configure [Default Email Reader].
The images in the [Email Images] folder are saved in the following location:
Open the [Users] folder, followed by [User login name], [Library], [Preferences], [ImageBrowserUserData], and [Mail].
COPY
Macintosh
Using Various Functions
63
Page 64
Running a Slide Show
1
From the [View] menu, select [Slide Show Options].
2
Select the slide show settings and click [OK].
• [Auto Play]: Select the interval by sliding the control under [Play Interval] (from 1 to 30 seconds).
• [Control with Mouse or Keypad]: Advances the slide show manually with the mouse or keyboard.
• [Repeat Continuously]: Runs the slide show in a loop.
• [Hides buttons]: Hides the buttons during the slide show.
• [Transition Effect]: Select the transition effect to be used when moving from one slide to another. When you select an effect, you can check the effect in the preview window.
COPY
3
Select the images and select [Slide Show] from the [View] menu.
Click on the lower right of the screen to end the slide show.
64
Using Various Functions
Page 65
Adding Sound to a Still Image
• To add sound to still images, use the Mac OS recording function. Depending on the computer, you may need to connect peripherals such as microphones. Check if your computer settings allow recording.
• The sound cannot be played back on the camcorder.
1
In the Browser Area, select a still image and select [Sound] [Record] from the [File] menu.
The recording window appears.
2
Click and start recording when the [Save] button is enabled.
3
Click [Save] to stop recording.
appears on the still image.
• The sound file will be copied in AIFF type (extension “.AIF”) to the same folder as the still image.
• To play back the sound, select an image with a sound icon and select [Sound] [Play] from the [File] menu.
To remove sound from a still image, select [Sound] [Send to Trash] from
the [File] menu. disappears and the copied sound file will be deleted.
While playing back the sound, select [Sound]  [Pause] or [Stop] to control
the status.
COPY
Macintosh
Using Various Functions
65
Page 66
Reviewing and Changing the Owner Name of the Camcorder
You can change and confirm the owner’s name of the camcorder.
Connect the camcorder to the computer ( 23).
1 2
Click the [Set to Camera] tab and click [Confirms/changes camera settings] in the Camera Control window.
3
Enter the camcorder’s owner’s name and click [OK].
Input the camcorder’s owner’s name here (up to 31 characters).
COPY
66
Using Various Functions
Page 67
Uninstalling the Software
Uninstall the software when you wish to delete it from your computer or when reinstallation is required to fix corrupted files.
Uninstalling ImageBrowser
Move the program’s folder and subfolders into the Trash to uninstall programs such as ImageBrowser.
If the program folders contain subfolders into which images have been
saved, be careful not to accidentally delete those subfolders.
For more details on how to uninstall ImageBrowser, refer to Read Me.
COPY
Macintosh
Uninstalling the Software
67
Page 68
Troubleshooting
Connection
Camcorder is not recognized when connected to the computer.
Î There is no memory card in the camcorder.
Insert a memory card into the camcorder.
Î The camcorder is not set to the correct mode.
Set the camcorder to still image playback mode.
Î Camcorder is not correctly connected to the computer.
Read Connecting the Camcorder to a Computer ( 23) and check the connection. Ensure that you are using the correct cable and that its connectors are in good shape.
Î If you are experiencing operational problems, detach the USB cable from
the camcorder and computer and terminate the connection. Restart the computer and then reconnect the camcorder.
ImageBrowser Operation
Cannot download still images.
Î The camcorder is not set to the correct mode.
Set the camcorder to still image playback mode.
Image files or folders do not appear in ImageBrowser.
Î Images or folders shown in ImageBrowser and the actual file contents
may be different.
Click the [View] menu and select [Refresh].
COPY
68
Troubleshooting
Page 69
CANON INC.
U.S.A. –––––––––– Canon U.S.A., Inc.
Canon Customer Care Center Tel (US): 1-800-828-4040 (Mon.-Fri., 9 AM to 8 PM Eastern Time)
CANADA
ASIA
––––––––––– Canon Hongkong Co., Ltd.
–––––––– Canon CANADA Inc.
Tel (Canada): 1-800-OK-CANON (1-800-652-2666)
19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong Phone: 852-2170-2828 Fax: 852-2723-9684
COPY
The information in this manual is verified as of 1 June 2008.
DIE-312M © CANON INC. 2008
Loading...