Canon CR-190i II, CR-135i II Instructions Manual

Instructions
Please read this manual before operating this scanner.

Connecting the Scanner to a Computer

Wizard Screen (Windows 7)
Connect the CR-135i II/CR-190i II to a computer as follows. Make sure to install the software before connecting the scanner to a computer.
• If you connect the computer and turn ON the CR-135i II/CR-190i II before installing the software, the following wizard screen appears. If this happens, click [Cancel], turn OFF the CR-135i II/CR-190i II, and then install the software. The following wizard screen is an example in Windows 7. When a similar wizard screen appears in Windows 8.1/10, click [Cancel].
2
A Install the software
Install the Scanning Utility for CR-135i/CR-190i in the setup disc provided with the CR-135i II/CR-190i II. (See “Installing the Software,” on p. 18.)
B Connect the scanner to a computer
Connect the CR-135i II/CR-190i II and the computer with a USB. (See “Connecting the Scanner to a Computer,” on p. 19.)
C Turn ON the power
Turn ON the power of the CR-135i II/CR-190i II. (See “Turning ON the Power,” on p. 20.)
D Automatically installing the device driver
The device driver is installed automatically when Windows recognizes the CR-135i II/CR-190i II as new hardware. (See p. 21.)
FCC REGULATIONS (For 120V model)
Check Reader, Model M111071/M111021/M111072/M111022 This device complies with Part 15 of the FCC Rules. Operation is subject to the following t wo conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Park, Melville, NY 11747, U.S.A. Tel. No. (800)652-2666
RADIO INTERFERENCE REGULATIONS (For 120V models)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry Canada.
RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For 120V models)
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par l’Industrie Canada.
ENERGY STAR® Office Equipment Program
This program is for U.S.A and Canada. As an ENERGY STAR® Partner, CANON ELECTRONICS INC. has determined that this machine meets the ENERGY STAR® Program guidelines for energy efficiency. The ENERGY STAR® Office Equipment Program is an international prog ram that promotes
backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment, such as computers, monitors, printers, fax, machine, copiers, and scanners. The standards and logos are uniform among participating nations.
This model doesn’t provide “setting options” for power management.
energy saving through the use of computers and other office equipment. The program
European Union (and EEA) only.
This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product shou ld be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service. For more information regarding return and recycling of WEEE products, please visit www.canon-europe.com/environment. (EEA: Norway, Iceland and Liechtenstein)
Für EMVG
Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und Gewerbebereich sowie in Kleinbetrieben vorgesehen.
Model Names
The following names may be provided for the safety regulations in each sales region of the Check Reader. CR-135i II: Model M111071 CR-190i II: Model M111021 CR-135i II UV: Model M111072 CR-190i II UV: Model M111022
3
Trademarks
• Canon and the Canon logo are registered trademarks, of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries.
• imageFORMULA is a trademark of CANON ELECTRONICS INC.
• Microsoft, Windows, Windows 7, Windows 8.1 and Windows 10 are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.
• Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
• Adobe, Acrobat, and Adobe Reader are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries.
• Other product and company names herein are, or may be, the trademarks of their respective owners.
• Ranger is a trademark of Silver Bullet technology, Inc.
Copyright
Copyright 2015 by CANON ELECTRONICS INC. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or b y any information storage or retrieval system without the prior written permission of CANON ELECTRONICS INC.
Reproduction Warning
This device is designed to be used in a legal manner, in accordance with all applicable laws, including, but not limited to, counterfeit and copyright laws, as well as laws pertaining to nation al security. Any person(s) found to have reproduced any of the following materials (regardless of whether such reproduction was intentional or not) for the purpose of misrepresenting such material as the original may be prosecuted in accordance with the applicable laws and regulations.
• Paper money or bank notes (domestic and foreign)
• Postage stamps, revenue stamps, or other similar stamps
• Stock certificates, bond certificates, promissory notes, cheques, or other valuable certificates
• Passports, licenses, or other certificates or documents issued by government officials or agencies
This is not an exhaustive list. Canon is not responsible for how this scanner is used by an individual. Please note that certain intellectual property is protected by copyright law, and copyrighted items may not be reproduced without the express permission of the copyright holder except for personal or household use under limited circumstances.
Disclaimers
The information in this document is subject to change without notice.
CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR IMPLIED, EXPECT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF USE OR NON-INFRINGEMENT. CAN ON ELECTRONICS INC. SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.
CANON ELECTRONICS INC. IS NO T LIABLE FOR THE STORAGE AND HANDLING OF DOCUMENTS SCANNED WITH THIS PRODUCT, OR THE STORAGE AND HANDLING OF THE RESULTIN G SCANNED IMAGE DATA. IF YOU INTEND TO DISCARD THE ORIGINALS OF THE SCANNED DOCUMENTS, YOU ARE RESPONSIBLE FOR INSPECTING THE SCANNED IMAGES AND VERIFYING THAT THE DATA IS INTACT. THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC. UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY.
4

INTRODUCTION

WARNING
CAUTION
IMPORTANT
NOTE
Thank you for purchasing the Canon Check Reader CR-135i II/CR­190i II. Please read this manual thoroughly before using the machine in order to familiarize yourself with its capabilities, and to make the most of its many functions. Unless otherwise noted, CR-190i II is used for both the CR-190i II and the CR-190i II UV models, and CR-135i II is used for both the CR-135i II and the CR-135i II UV models, throughout this manual.
Manuals for the CR-135i II/CR-190i II
The following manuals are provided with the CR-135i II/CR-190i II. Be sure to read these manuals thoroughly before using the scanner. (The Installation Guide and the Operation & Maintenance Guide are extracted from the Instructions.) Electronic manual is stored as a PDF file on the supplied Setup Disc and requires Adobe Reader to open. (You can download Adobe Reader from the Adobe Web site.)
Installation Guide (Supplied with the scanner/Electronic Manual)
Describes the procedure for setting up the CR-135i II/CR-190i II for scanning. Set up the CR-135i II/CR-190i II in accordance with the Installation Guide. For details on the CR-135i II/CR-190i II, refer to the Instructions (electronic manual).
Operation & Maintenance Guide (Supplied with the scanner/ Electronic Manual)
Describes the basic operations for using the CR-135i II/CR-190i II, troubleshooting, and maintenance. For details on the settings of the CR-135i II/CR-190i II, refer to the Instructions (electronic manual).
Instructions (Electronic Manual): This Manual
Describes how to use the scanner, and includes instructions for configuring the scanner settings, as well as handling, maintenance, and troubleshooting information.
Symbols Used in This Manual
The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety.
Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. To use the machine safely, always pay attention to these warnings.
Indicates a caution concerning operations that may lead to injury to persons, or damage to property if not performed correctly. To use the machine safely, always pay attention to these cautions.
Indicates operational requirements and restrictions. Be sure to read these items carefully to operate the machine correctly, and avoid damaging the machine.
Indicates a clarification of an operation, or contains additional explanations for a procedure. Reading these notes is highly recommended.
5

Table of Contents

Connecting the Scanner to a Computer............................................... 2
INTRODUCTION ................................................................................. 5
Manuals for the CR-135i II/CR-190i II...................................... 5
Symbols Used in This Manual.................................................. 5
Important Safety Instructions ............................................................... 8
Handling................................................................................... 8
Installation Location ................................................................. 9
Power Supply......................................................................... 10
Moving the Scanner ............................................................... 10
Introduction to the CR-135i II/CR-190i II............................................ 11
Features of the CR-135i II/CR-190i II .......................................... 11
Features ................................................................................. 11
Packaging: What Is in the Box? ................................................... 12
Part Names .................................................................................. 13
Front View .............................................................................. 13
Rear View............................................................................... 15
Connector............................................................................... 15
Exterior Dimensions ..................................................................... 15
Preparation Before Use ..................................................................... 16
Setting Up the Scanner................................................................ 16
Checking Your Operating Environment ....................................... 17
Installing the Software.................................................................. 18
Installing the Scanning Utility ................................................. 18
Connecting the Scanner to a Computer....................................... 19
USB Connections ................................................................... 19
Connecting the Power Cord................................................... 20
Turning ON and OFF the Power.................................................. 20
Turning ON the Power ........................................................... 20
Turning OFF the Power.......................................................... 21
Preparing the Ink Cartridge.......................................................... 22
About the Ink Cartridge .......................................................... 22
Setting the Ink Cartridge and Adjusting the Print Position ..... 22
Software............................................................................................. 24
How to Use the Software ............................................................. 24
How to Use the Scanning Utility............................................. 24
How to Use the Ranger .......................................................... 26
Uninstalling the Software ............................................................. 27
Document Feeding and Scanning...................................................... 29
Documents................................................................................... 29
Document............................................................................... 29
Envelope ................................................................................ 30
Using Ultrasonic Double Feed Detection ............................... 31
Placing Documents ................................................................ 31
Document Feeding and Scanning................................................ 32
Scan Procedure ..................................................................... 33
Separation OFF Mode............................................................ 35
Auto Power OFF Settings ...................................................... 35
Troubleshooting ................................................................................. 37
When the Scanner Is Not Recognized......................................... 37
Clearing Paper Jams ................................................................... 37
Feeding Trouble........................................................................... 39
When the Scanned Image Is Not Normal .................................... 41
6
Maintenance ...................................................................................... 42
Daily Cleaning.............................................................................. 42
Cleaning the Main Unit ........................................................... 42
Cleaning the Feed Path ......................................................... 42
Cleaning the Scanning Glass and Rollers.............................. 44
Cleaning the Magnetic Heads................................................ 47
Cleaning the Ink Jet Nozzles.................................................. 48
Cleaning with the Cleaning Cards (United States Only) ........ 49
Maintenance ................................................................................ 50
Replacing the Ink Cartridge.................................................... 50
Replacing the Ink Disposal Tank............................................ 51
Replacing the Rollers ............................................................. 53
Adjusting the Separation Roller Gap ...................................... 56
Specifications ............................................................................... 57
Scanner Specifications........................................................... 57
Index .................................................................................................. 58
7

Important Safety Instructions

WARNING
CAUTION
Handling
Never install and operate the scanner near flammable substances, such as alcohol, paint thinner, benzene, or any other type of volatile solution.
Never damage or modify the power cord, and never place heavy objects on the power cord.
Always make sure that your hands are dry when you are handling the power cord or power plug. Never grasp the power plug when your hands are wet.
Never plug the scanner into a multiplug power strip.
Never bundle, wrap, or tie the power cord around itself or another
object. Connect the power plug securely into the power outlet.
Use only the power cord and power plug provided with the scanner.
Never attempt to disassemble or modify the scanner.
Never use flammable aerosol products near the scanner.
Before you clean the scanner, turn the power OFF and disconnect
the power cord from the power outlet.
To clean the scanner’s exterior, use a firmly wrung cloth, moistened slightly with water or mild detergent. Never use any type of volatile solution, such as alcohol, benzene or paint thinner.
If you hear strange sounds, detect smoke or abnormal heat, sense vibration, or smell odd odors around the scanner, turn OFF the power switch immediately and disconnect the power cord from the power outlet. Contact your local authorized Canon dealer or service representative to have the scanner serviced.
8
Handle the scanner with care. Avoid shock and vibration to the scanner caused by reckless handling. If you suspect the scanner has been accidentally damaged, turn OFF the power switch immediately and disconnect the power cord from the power outlet. Contact your local authorized Canon dealer or service representative to have the scanner serviced.
Before you move the scanner, always turn OFF the power and disconnect the power cord from the power outlet.
This product emits low level magnetic flux. If you use a cardiac pacemaker and feel abnormalities, please be away from this product and consult your doctor.
To avoid damage to the scanner, never place the scanner on an unstable or vibrating causing injury.
To avoid overheating and causing a fire, never block the air vents on the back of the scanner.
Keep all liquids, beverages, or any type of liquid, and clips, staples, necklaces, or other metal objects away from the scanner. If you accidentally spill liquid or drop a metal object into the scanner, turn OFF the power immediately and disconnect the power cord from the power outlet. Contact your local authorized Canon dealer or service representative to have the scanner serviced.
Never install the scanner in humid or dusty locations. Doing so may cause a fire or electrical shock.
Never place heavy objects on top of the scanner, as these objects may tip or fall over, and cause injury.
surface. The scanner may tip or fall over,
When you remove the power cord, grip it by the power plug head.
100 mm (3.9")
706 mm (27.8")
356 mm (14")
466 mm (18.3")
125 mm (5")
Never attempt to disconnect the power cord from the power outlet by pulling on the power cord. Doing so may damage or expose the cord’s internal wiring, and cause a fire or electrical shock.
Keep the area around the power outlet clear of all obstacles so you can disconnect the power cord easily at all times.
Never spill water or volatile solutions (alcohol, benzene, paint thinner) into the scanner. Doing so may cause a fire or electrical shock.
When the scanner is not being used for a long period of time, disconnect the power cord from the power outlet.
Avoid wearing loose fitting clothing, dangling jewelry, long ties, or long hair that could become entangled with moving parts, especially the rollers that feed paper into the scanner. If such objects become entangled, immediately disconnect the power plug from the power outlet to stop the scanner.
Be careful when you are loading a document or clearing a paper jam. It is possible that the paper edges may cut your fingers.
Do not open the Maintenance Cover while the scanner is operating. Doing so may result in a malfunction or injury.
Do not touch the pins and contacts on the scanner’s connector with your hands. Doing so may result in a malfunction.
Do not touch anything except the operation buttons when the jogger is operating (CR-190i II/CR-190i II UV only) or documents are being fed.
Do not turn the scanner upside down. The ink may leak from the ink disposal tank.
Installation Location
For operation, maintenance, and ventilation, make sure that there is enough space around the scanner, as shown in the illustration above.
Avoid placing the scanner in the following places. It may cause a malfunction and adversely affect the scanner or your computer.
• Places exposed to direct sunlight If installation in such places is unavoidable, provide a curtain or similar object to shade the scanner.
• Places subject to dust and fumes Dust and cigarette fumes adversely affect the components inside the scanner.
• Near running water, a heat source, water vapor, or in an area, such as a laboratory exposed to ammonia gas, paint thinner, or other volatile chemicals
• Places subject to excessive vibration and shock
9
• Places subject to rapid changes in temperature or humidity
WARNING
Condensation occurring inside the scanner may impair image quality. Place the scanner in a room that is within the following range:
Room temperature: 10°C to 32.5°C (50°F to 90.5°F)
Relative humidity: 20% to 80% RH Use the recommended operating environment for the ink cartridge when using the imprinter.
• Near electronic equipment or heavy equipment that generates a strong magnetic field, such as a speaker, TV, and radio
Power Supply
• Connect only to a power outlet of the rated voltage and power supply frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz, depending on your region).
• Make sure that the scanner is connected to an independent power outlet. Do not plug the scanner into an outlet shared with another device. If you use an extension cord, make sure that the extension cord is rated for the current requirements of the scanner.
• If you are unsure of anything relating to the power supply, contact your local authorized Canon dealer or service representative for further information.
• Never place an object on top of the power cord or step on the power cord.
• Never bundle the power cord or wrap the cord around an object, such as a table leg.
• Do not tug on the power cord. When you remove the power cord, grip it by the power plug head.
• Keep the area around the power outlet free of obstacles.
Moving the Scanner
When you move the CR-135i II/CR-190i II, hold it firmly with both hands and carry it carefully. Do not hold the scanner by the Eject Stopper. The scanner weighs approximately 8.0 kg (17.1 lb) or 8.4 kg (18.5 lb).
When moving the scanner, be sure to turn OFF the power and remove any cables. If the cables are not removed before moving the scanner, you may damage the plugs or connector by forcibly pulling them out.
10

Introduction to the CR-135i II/CR-190i II

This chapter describes the features of the CR-135i II/CR-190i II scanner, what comes packaged in the box, and the names and functions of parts on the scanner.

Features of the CR-135i II/CR-190i II

The Canon Check Reader CR-135i II/CR-190i II is a scanner with magnetic heads that can read checks and other documents that are printed with MICR (Magnetic Ink Character Recognition) compatible fonts, and is capable of OCR (Optical Character Recognition).
Features
High-Speed Scanning (200 dpi American checks)
CR-135i II: 135 cpm CR-190i II: 190 cpm CR-135i II UV: 120 cpm (UV Scan mode) CR-190i II UV: 160 cpm (UV Scan mode)
Supports Large Documents
Documents up to 108 mm x 245 mm (4.3" x 9.6") can be scanned.
High Durability
The scanner has a high durability of 24 million scans.
Compact Size
Supports Black-and-White (Binary) and Grayscale Output
Reads MICR Characters
A magnetic head is used to scan MICR characters.
Supports OCR (Optical Character Recognition)
Character images, such as E13B, OCR-A, OCR-B, and check writer are recognized as characters by the OCR function.
Supports UV scanning (UV models only)
The CR-135i II UV/CR-190i II UV can scan images that are printed with UV fluorescent ink. This function only scans the front side of documents.
Easy to Maintain
Large Maintenance Covers make handling paper jams and cleaning easy.
Jogger Mechanism Is Standard (CR-190i II/CR-190i II UV only)
A jogger mechanism, which uses vibration to align documents, comes standard equipped with the CR-190i II/CR-190i II UV.
Separation OFF Mode
You can scan the following documents:
• Thick documents
• Documents that contain two or more pages together as one document
• Documents that have a rough surface
• Duplicate forms that have sticky edges
Paper Thickness Adjustment Mechanism
Adjust the Separation Roller gap to the thickness of the paper being fed.
11
Three Eject Pockets and Automatic Sorting Mechanism
CR-135i II/CR-190i II
Setup Disc Power Cord
*1
Warranty Card
*2
USB Cable
*1 The power cord varies, according to the country of purchase. *2 For the United States and Canada only.
Installation Guide Operation & Maintenance Guide
The scanner has three Eject Pockets and the documents are automatically ejected to each pocket according to sort methods. The scanner fits various scan operations using this mechanism.
Ultrasonic Double Feed Detection and Double Feed Detect OFF Button (Scanning Utility for CR-135i/CR-190i)
The scanner detects double-fed documents using ultrasonic, and can turn OFF the function with the Function Button.
Drop-Out Color
This function enables drop-out scanning of a specific color in the document.
Imprinter Is Standard Equipment
An imprinter mechanism, which prints text (4 lines) or a bitmap on documents as they are scanned, comes standard equipped with the scanner. The imprinter’s ink cartridge is not included, and must be purchased separately. (See “About the Ink Cartridge,” on p. 22.)
Eject Pocket Full Detection (Scanning Utility for CR-135i/ CR-190i)
Detects when any one of the three Eject Pockets is full and stops scanning. This function is available only on CR-135i II/CR-190i II/CR­190i II UV. (See “Scan Procedure,” on p. 33.)
Placing Additional Documents
You can place additional documents while the machine is scanning.
Replaceable rollers and ink disposal tank
You can replace the rollers (Pickup Roller, Feed Roller, and Separation Roller) and the ink disposal tank.

Packaging: What Is in the Box?

Make sure that you have everything shown below. Check every item you have removed from the box. If any items are missing, contact your local authorized Canon dealer.
12

Part Names

Power Switch
Front Maintenance Cover
Open this cover to clear paper jams or to clean the scanner.
Roller Cover
Operation Buttons
Ink Cartridge
Ink cartridge is not included. Purchase the ink cartridge separately. (See “About the Ink Cartridge,” on p. 22.)
JOG: Uses vibration to align the documents. (Jogger)
This button is available only on the CR-190i II/ CR-190i II UV.
Function (F): You can assign this button to any function from
an application. When using the accompanying Scanning Utility for CR-135i/CR-190i, switches the double feed detection ON/OFF.
START: Starts scanning operations. Press and hold
this button during a paper jam to eject the jammed document.
STOP: Stops scanning operations.
Scanner Unit
This unit scans the documents.
Magnetic Head for MICR
Reads MICR characters that have been printed with magnetic ink.
Built-in Nozzle Cleaning Pad
This section describes the names and functions of each part. Before you connect the CR-135i II/CR-190i II, familiarize yourself with its parts and their functions.
Front View
13
Back Maintenance Cover
Open this cover to clear paper jams or to clean the scanner.
Separation OFF Mode Button
Use this button when you want to scan the following documents (See “Separation OFF Mode,” on p. 35.):
• Thick documents
• Documents that contain two or more pages together as one document
• Documents that have a rough surface
• Duplicate forms that have sticky edges
Adjustment Dial Cover
Top Cover
Adjustment Dial
Adjust the Separation Roller gap if feeding errors occur too frequently. (See “Adjusting the Separation Roller Gap,” on p. 56.)
Eject Stopper
Pull out the Eject Stopper to prevent documents from falling off the output tray.
Eject Pocket
Documents are separated with flappers into three pockets. (See p. 34)
Scanner Unit
This unit scans the documents.
14
Rear View
CAUTION
Ink Disposal Tank Pocket
Connector
Air Vent
Power Cord Connector
Connect the power cord provided with the scanner to this connector.
USB Connector
Connect a Hi-Speed USB 2.0 compatible cable. (See “USB Connections,” on p. 19.)
476 mm (18.7")
272 mm (10.7")
581 mm (22.9") (with the eject stopper open)
177 mm (7")
137 mm (5.4")
213.5 mm (8.4")
To avoid overheating and causing a fire, never block the air vents on the back of the scanner.
Connector

Exterior Dimensions

Units: millimeters (units in parenthesis are inches)
15

Preparation Before Use

IMPORTANT
Wizard Screen (Windows 7)
This chapter describes how to prepare the scanner to scan documents.

Setting Up the Scanner

Perform the following steps to set up the CR-135i II/CR-190i II. Refer to the section for each step for details about that step.
A Check your operating environment. (See “Checking Your
Operating Environment,” on p. 17.)
B Install the software. (See “Installing the Software,” on
p. 18.)
Install the Scanning Utility provided with the CR-135i II/CR-190i II.
C Connect the scanner to a computer. (See “Connecting
the Scanner to a Computer,” on p. 19.)
D Turn ON the power. (See “Turning ON the Power,” on
p. 20.)
E Automatically installing the device driver. (See p. 21.)
The device driver is installed automatically when Windows recognizes the CR-135i II/CR-190i II.
To have the device drivers installed automatically when the computer recognizes the CR-135i II/CR-190i II, the software needs to be installed before the CR-135i II/CR-190i II is connected to the computer.
If you connect the computer and turn ON the CR-135i II/CR-190i II before installing the software, the following wizard screen appears. If this happens, click [Cancel], turn OFF the CR-135i II/CR-190i II, and then install the software. The following wizard screen is an example in Windows 7. When a similar wizard screen appears in Windows 8.1/10, click [Cancel].
16
IMPORTANT

Checking Your Operating Environment

The following computer system requirements are recommended for using the CR-135i II/CR-190i II.
Operating Systems:
• Microsoft Windows 7 (32/64bit) SP1 or later
• Microsoft Windows 8.1 (32/64bit)
• Microsoft Windows 10 (32/64bit)
• Microsoft Windows Server 2008 R2 Service Pack 1 or later
• Microsoft Windows Server 2012 R2
• Microsoft Windows Server 2016
• Microsoft Windows Server 2019 This is the environment as of December 2018. For the latest software support information, go to the Products page on the Canon website.
Specifications:
• CPU: Intel Core2 Duo 3.0 GHz or faster
• Memory: 1 GB or more
• USB 2.0 interface
Interface Cable
• Use the cable provided or a Hi-Speed USB 2.0 interface cable to connect to the computer’s USB port.
If you use the USB interface that was provided as standard with your computer:
Use the most recently available USB 2.0 driver provided by Microsoft.
Contact your local authorized Canon dealer for more detailed information.
Not all USB interfaces provided as standard with personal computers
are guaranteed. Contact your local authorized Canon dealer for more detailed information.
Scanning speeds are slower if your computer’s standard USB interface
is USB 1.1.
You should use the USB cable originally bundled with the scanner or a
Hi-Speed USB 2.0 compatible cable.
If the CPU, memory, interface card, and other specifications do not satisfy the installation requirements, the scanning speed may be greatly reduced and transmission may take longer.
Even if the computer satisfies the system requirements, the scanning speed may vary, depending on the specifications and operating environment of the computer and the specified scan settings.
17
IMPORTANT
NOTE
IMPORTANT

Installing the Software

The following software applications are provided on the setup disc that is packaged with the scanner. Make sure to open and read the Readme.txt file on the setup disc before installing the software.
Scanning Utility
Canon Scanning Utility is an application that provides scanning, file saving, image viewing, printing, and various other functions. A dedicated scanner driver is installed after you install the utility software.
Ranger
Ranger is an API software. For details, see “About the Ranger,” on p. 26.
The Scanning Utility includes a device driver so that Windows can recognize the CR-135i II/CR-190i II. Be sure to install the Scanning Utility before connecting the CR-135i II/CR-190i II to the computer.
Some functions mentioned in this manual may not be operated in some applications.
Installing the Scanning Utility
Follow the instructions below to install the Scanning Utility and the dedicated driver.
The dedicated scanner driver is installed after the Scanning Utility has been installed.
A Turn ON your computer, and log on to Windows.
Be sure to log on as the Administrator.
B Insert the setup disc into the Disc drive.
This manual assumes that “D” is assigned to your Disc drive.
C Click [Start], and then click [All Programs].
The procedure in Windows 7/8.1/10 is different from the ones described in this manual. Refer to the Windows 7/8.1/10 “Help and Support Center” to select [Run].
18
D Click [Accessories], and then click [Run].
IMPORTANT
CAUTION
NOTE
Type A Plug Type B Plug
USB Cable
USB Connector
E Enter “D:\SU190i\setup.exe” in the [Open] fields, and then
click [OK].
Installation starts.
F Follow the instructions on the screen to complete the
installation.
The computer may need to be restarted, after the installation, depending on the operating system. If this is necessary, make sure to restart the computer.

Connecting the Scanner to a Computer

The only way to connect the scanner to your computer is with a USB cable.
Do not turn OFF the scanner or remove the interface cable when an application is running.
Turn OFF the computer and the scanner before changing the cable.
USB Connections
Connect the scanner and the computer with the USB cable provided or a Hi-Speed USB 2.0 cable.
Connect the type B plug (square) to the scanner and connect the type A plug (flat) to the USB port on the computer.
19
Loading...
+ 44 hidden pages