Canon CLC-10 Service Manual

Specifications and Main Features

Category: Personal computer
Copying device type: Non-removable
Lighting device type: Halogen bulb (20 Watts)
Types of lenses: Lens array
Imaging device type: Photoelectric element (BASIS)
Scanner unit image over 1-bit output: Exterior interface
RGBexternalinterface_RDB: 3 type (8 bits each)
Reproduction: Bubble ink jet (BJ)
Head nozzle parameters: 128 nozzles/row (one unit)
Ink deposition value: 400 dots per inch (15.75 dots per mm)
Image density adjustment: Non-Automated adjustment
Ink supply unit(s): Not available (on BJ replacement)
Ink type: Water based inks, cyan, magenta, yellow and black
Paper cassette: single, Automation
BJ head type: Integrated head assembly and a replaceable cartridge containing an inktank; four heads
BJ head cleaning: Automatically (at switch-on; before, during, and after copying process); Semi automatic (on pressing the CLEAN key)
Waste ink collection method: Tank with absorbent at the bottom of the body
Document types: Sheet, Book, 3-D (up to 2kg)
Maximum document size: A4 (LTR)
Copying range: A4 (LTR) to A6 (STMT) inclusive
Reproduction ratio: DIRECT ratio equals 1:1 (40.5%); ZOOM – range from 1:0.500 to 2.00 (1.0% increments)
Main scanning direction and maximum resolution: 400 dpi
Sub scanning direction: 400 dpi
Continuous Coping: Maximum 19 copies
Time between copies, maximum: 10 sec or less* (20 degrees celsius)
Time for first copy: 90 seconds or so; margins A4
The speed of copying takes about 95 seconds for a single A4 sheet in direct mode.
The copy paper consists of, but is not limited to special coated paper, special oHP film, special postcard, and special label sheets.
A two-sided copy of a document cannot be produced with the copier.
Overlay copying with this copier is not an option.
The cassette of the machine is approximately 20mm deep which can hold an estimated 90 coated papers, it is fitted with a claw.
The pick-up from the manual tray is one sheet, but from the cassette it is 90 sheets.
The maximum number of copy tray that sheets can hold for the copier is 19 sheets.
The non image width for coated papers is 5mm while for OHP film it is approximately 16mm.
OHP films has a non image width of 8.5mm while coated pieces have 5mm.
For coated papers the trailing edge measures 5 mm but can vary with the size, on the other hand A4 and LTR OHP film is sized at 18 mm.
Some of the compatible copies include Film Projectors, Editor Unit and Video Adaptors.
The required temperature ranges from 15 celsius to 30 celsius while humidity levels should be between 5% to 80%. A minimum atmospheric pressure of 0.6 to a maximum of 1 atm is tolerated.
The input can range from 220 to 240 volts at 50 hertz.
The machine is rated at 0.12 kw but it also on standby consumption of power upto 12w.
While copying the machine consumes about 68 w.
The exposure decibel rating of the machine is 50 dB or lower while the standby decibel rating is lower than 40 dB.
Dimension wise the machine measures 540mm in width, 476mm in depth and 217 mm in height.
The machine itself weighs around 19.5 kg.

Frequently Asked Questions

Q: Which type of ink is utilized by the CLC10?

A: The CLC10 is able to use four types of water based inks, these include cyan, magenta, yellow and black.

Q: Which are the largest paper formats that the CLC10 can process?

A: The largest size of the paper that the copy machine can accommodate is A4 (LTR) while the smallest it can go down to is A6 (STMT).

Q: Is there a limit to the maximum amount of copies that can be taken, and if so, what is it?

A: The maximum number of copies that the CLC10 can take in a single session is 19 which are done in a single continuous movement.

Q: Is there a possibility to have a two sided copy made?

A: No, this device CLC10 does not have the capability to print two sided copies and is only single sided.

Q: How long does it take to copy an A4 size paper?

A: It takes only about +95 seconds to replicate an A4 sized paper while in the direct mode.

Q: Are there any facilitating services which can assist in enhancing the color to enhance the copying experience?

A: The CLC10 comes equipped with various features which can help with color enhancement such as color balance density adjustment and many modes with the most popular one being the photo mode.

Q: Is there any method through which the ink cartridge can be changed?

A: Yes, the user has to follow a few defined steps in a certain order to ensure a smooth replacement which includes opening the front panel, Ensuring that a specific head carriage is in a specific location and checking the manual.

Q: What are the optimal range of temperature and humidity for the CLC10 to work efficiently?

A: The optimal conditions include working temperatures ranging from 15° to 30°C, providing a temperature and humidity level of 5% to 80%.