Canon 7561A001 User Manual

Mini

Digital Video Cassette

DIGITAL VIDEO CAMCORDER

Instruction Manual

This instruction book explains the use of the MV500 and MV500i camcorders. The main difference between these models is that the MV500i includes a DV Recording and Analog Line-in Recording function. Please note that illustrations and explanations in this instruction book refer mainly to the MV500 model.

Introduction

Mastering

the Basics

Using the Full

Range of Features

Editing

Additional

Information

PUB.DIE-168

Downloaded From VideoCamera-Manual.com Manuals

Important Usage Instructions

Introduction

WARNING:

CAUTION:

DISCONNECT THE MAINS PLUG FROM THE SUPPLY SOCKET WHEN NOT IN USE.

For Users in the UK

When replacing the fuse only a correctly rated approved type should be used and be sure to re-fit the fuse cover.

CAUTION: CUSTOMERS IN THE U.K. SHOULD READ THIS BEFORE USING THIS PRODUCT.

CHANGING THE FUSE

CHANGING THE PLUG

THE SEVERED PLUG MUST BE DESTROYED IMMEDIATELY TO AVOID ANY POSSIBLE ELECTRIC SHOCK HAZARD.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

THE MAINS LEAD ON THIS PRODUCT IS FITTED WITH A NON-REWIREABLE (MOULDED) PLUG, INCORPORATING A 3 AMP FUSE. SHOULD THE FUSE NEED TO BE REPLACED AN ASTA OR BSI APPROVED BS1362 FUSE OF THE SAME RATING MUST BE USED.

ALWAYS REFIT THE FUSE COVER AFTER REPLACING THE FUSE. NEVER USE THE PLUG WITH THE FUSE COVER OMITTED.

IF THE FITTED PLUG IS NOT SUITABLE FOR YOUR SOCKET OUTLETS, IT SHOULD BE CUT OFF AND AN APPROPRIATE PLUG FITTED IN ITS PLACE. IF POSSIBLE FIT AN APPROPRIATE 3 AMP FUSE. IF THE NEW PLUG HAS NO FUSE, THEN FIT A 5 AMP FUSE AT THE DISTRIBUTION BOARD.

AC POWER CORD CONNECTION

The wires in the mains lead of this apparatus are coloured in accordance with the following cord.

(IMPORTANT)

Mains Lead

As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. Neither Blue wire or Brown wire is to be connected to the Earth pin of a 3 pin plug.

BLUE ..................NEUTRAL

BROWN...............LIVE

CA-560 identification plate is located on the bottom.

• Use of CV-150F/CV-250F DV cable is necessary to comply with the technical requirement of EMC Directive.

Downloaded From VideoCamera-Manual.com Manuals

Introduction

Important Usage Instructions ....................2

Thank you for Choosing a Canon ..............5

Introducing the MV500/MV500i ..............6

Mastering the Basics

Finding Your Way Around

the MV500/MV500i..............................7

~ Preparations ~

Attaching the Ferrite Core........................10

Powering Your Camcorder ......................11

Loading a Cassette ..................................16

~ Basic Recording ~

Basic Recording ......................................18

Zooming ..................................................23

Using the LCD Screen ............................25

~ Basic Playback ~

Playing Back a Cassette ..........................28

Connections for Playback on a

TV Screen............................................32

Tips for Making Better Videos ................36

Using the Full Range of Features

~ When Making Manual Adjustments ...~

Ajusting AE Shift ....................................65

Setting the Shutter Speed ........................66

Adjusting Focus Manually ......................68

Setting the White Balance........................69

~ For Playback ...~

Displaying Date, Time and Camcorder Data

Searching the Tape (Photo Search/

Returning to a Pre-Marked Position ........75

Editing

Editing to a VCR......................................76

Dubbing with Digital Video Equipment ..77

Recording from a VCR, TV or Analog

Digitally Outputting Analog Video and

Recording Over Existing Scenes

Audio Dubbing ........................................88

Setting the Audio Mix..............................93

Connecting to a PC Using a DV Cable....95

~ General ... ~

Searching and Reviewing

While Recording ................................38

Using the Menus ......................................39

Using the Wireless Controller..................43

~ For Recording ...~

Setting the Date and Time........................46

Taking Still Pictures ................................49

Turning the Image Stabilizer Off ............51

Using the Various Recording Programs ..52

Using Digital Effects................................56

Audio Recording ......................................61

Setting the Self-Timer ..............................63

Additional Information

Preparing the Camcorder..........................96

Notes on Using the Batteries....................98

Maintenance ..........................................101

Troubleshooting......................................105

The MV500/MV500i System Diagram..108

Optional Accessories ..............................109

Screen Displays ......................................111

Specifications..........................................117

Index ......................................................118

Menu at a Glance ..................................120

Downloaded From VideoCamera-Manual.com Manuals

Introduction

(Data Code) ........................................71

Date Search) ........................................74

Camcorder – Analog Line-in

(MV500i only) ....................................81

Audio Signals – Analog-Digital

Converter (MV500i only) ..................83

– AV Insert Editing (MV500i only) ....85

For quick reference

In addition to the contents and index please refer to:

• Finding Your Way Around the MV500/MV500i ( 7)

• Screen displays ( 111)

• Troubleshooting — in case you run

Introduction

into any problems ( 105)

• Menu at a Glance ( 120)

Symbols used in this instruction manual:

: Reference page numbers : Functions that can be operated

from the body of the camcorder

: Functions that can be operated

from the wireless controller

: Supplementary notes for

camcorder operation

` : Operation confirmation beeps

( 21)

• Capital letters are used to refer to settings displayed in the menus and buttons labelled on the camcorder itself, e.g. Press the MENU button.

Downloaded From VideoCamera-Manual.com Manuals

Thank you for Choosing a Canon

First, we’d like to thank you for purchasing this Canon camcorder. Its advanced technology makes it very easy to use — you will soon be making high-quality videos which will give you pleasure for years to come.

To get the most out of your new camcorder, we recommend that you read this manual thoroughly — there are many sophisticated features which will add to your recording enjoyment.

Getting started

To get started we suggest that you master the basic operations of the camcorder first, before moving on to use its full range of features.

• When connecting the camcorder to your personal computer, use the optional CV-150F or CV-250F DV cable.

Your camcorder is supplied with the following accessories:

WL-D74 Wireless Controller

SS-800 Shoulder Strap Lens cap and lens cap

BP-508 Battery Pack

Lithium button battery

Two AA batteries

cord

CA-560 Compact Power Adapter (including AC power cable)

STV-250N Stereo Video Cable

Introduction

PC-A10 SCART Adapter (Europe, Asia)

Downloaded From VideoCamera-Manual.com Manuals

Ferrite Core

Introducing the MV500/MV500i

The MV500/MV500i is small and light. Many various functions are condensed into its compact body. Also, the slim and stylish design makes it easy to carry and use and shooting videos a pleasure.

Introduction

18× Lens and 360× Digital

Zoom

Compact and Stylish

From wide-angle to 18× telephoto—with unparalleled optical quality. The digital zoom magnifies this up to 360× for even more dramatic results.

Night Mode

In dark places, automatically adjusts to the optimum shutter speed according to the brightness of the subject for shooting brightly in colour.

IEEE 1394 DV Terminal

Using a DV cable, connect the comecorder to a PC equipped with a DV terminal and transfer your original images and sound to your PC.

Still Photos

Just press the photo button to capture still pictures.

2.5” LCD Screen

A 2.5” LCD screen makes it easy for you to shoot colourful, well composed video. It is also great for playback.

Image Stabilizer

Stabilizes your recordings even in long telephoto shots.

Digital Effects

Advanced digital technology allows you to add special effects during recording or playback.

Audio Dubbing

Add new sound to original sound on a prerecorded tape.

Analog Line-in Recording and

AV Insert Editing (MV500i only)

Connect to a VCR or analog camcorder and record to a DV tape in the MV500i. Also, replace original images on a pre-recorded tape.

Downloaded From VideoCamera-Manual.com Manuals

Finding Your Way Around the MV500/MV500i

Easy Recording

Program AE

DATA CODE

ON/OFF

DIGITAL EFFECTS

REC (record) SEARCH

–

button(p. 38)/

Record review button (p. 38)/ (rewind) button (p. 28)

REC SEARCH

button (p. 38)/

(fast forward) button (p. 28)

FOCUS button (p. 68)/ (play/pause) button (p. 28)

AE SHIFT button (p. 65)/ (stop) button (p. 28)

LCD screen (p. 25)

BATT. (battery) RELEASE button (p. 13)

Battery attachment unit (p. 12)

LCD panel OPEN button (p. 25)

DIGITAL EFFECTS button (p. 59)

Digital effects ON/OFF button (p. 59)

Self-timer button (p. 63)/ DATA CODE button (p. 71)

Selector dial (p. 31, 39)

MENU button (p. 39)

Program selector (p. 52)

Backup battery cover (p. 100)

Strap attachment bar (p. 97)

the Basics

Mastering

Downloaded From VideoCamera-Manual.com Manuals

Zoom controller (p. 23)

PHOTO button (p. 49)

Speaker (p. 31)

POWER indicator (p. 18)

Grip belt (p. 96)

Cassette compartment (p. 16)

Cassette compartment cover (p. 16)

Viewfinder focusing lever (p. 96)

Viewfinder protect cover (p. 102)

Viewfinder (p. 96, 102)

POWER switch (p. 18)

Start/Stop button (p. 19)

Strap attachment bar (p. 97)

Accessory shoe (p. 88)

CAMERA

•

OFF

•

PLAY(VCR)

•

}

CAMERA

OFF

PLAY(VCR)

POWER

Mastering

the Basics

Downloaded From VideoCamera-Manual.com Manuals

SET

MIC

DC IN

9.5V

CHARGE

Bottom view

REW

PLAY

START /STOP

PHOTO

SELF TIMER

SCREEN

DATA

CODE

D.EFFECTS

AUDIO

MONITOR

REC

PAUSE

SEARCH SELECT

ZERO SET MEMORY

AUDIO

DUB.

STOP

MIX

BALANCE

ST-1

ST-2

ON/OFF

SET

ZOOM

INSERT

PAUSE

SLOW

REMOTE SET

–/

WIRELESS CONTROLLER WL-D74

× 2 button (p. 30)

START/STOP button (p. 19)

MENU button (p. 39)

TV SCREEN button (p. 111)

SELF TIMER button (p. 63)

DATA CODE button (p. 71)

D.EFFECTS (Digital effects) button (p. 59)

REC PAUSE button (p. 79, 82) (MV500i only)

ZERO SET MEMORY button (p. 75)

Transmitter

Zoom buttons (p. 23)

SET button (p. 40)

Digital effects ON/OFF button (p. 59)

MIX BALANCE buttons (p. 93)

Controller buttons (p. 40)

Search buttons (p. 74) SEARCH SELECT button (p. 74)

AUDIO MONITOR button (p. 93)

AUDIO DUB. button (p. 89)

AV INSERT button (p. 87) (MV500i only)

REMOTE SET button (p. 44)

button (p. 29)

FF button (p. 28) PLAY button (p. 28)

STOP button (p. 28)

SLOW button (p. 29)

REW button (p. 28)

PAUSE button (p. 29)

PHOTO button (p. 49)

MV500: S-video OUT terminal (p. 34) MV500i: S-video IN/OUT terminal (p. 34, 81)

MV500: DV OUT terminal (p. 77, 95) MV500i: DV IN/OUT terminal

(p. 78, 95)

DC IN terminal (p. 11)

Remote sensor (p. 43)

Terminal cover

CHARGE indicator (p. 12)

MIC terminal (p. 61, 88)

Tripod socket (p. 36)

OPEN/EJECT switch (p. 16)

Stereo microphone (p. 88)

Terminal cover

(LANC) terminal (p. 76)

MV500:

AV (audio/video) OUT terminal (p. 32)/ (phones) terminal (p. 32)

MV500i:

AV (audio/video) IN/OUT terminal (p. 32, 81)/ (phones) terminal (p. 32)

Downloaded From VideoCamera-Manual.com Manuals

the Basics

Mastering

Attaching the Ferrite Core

4cm

Attach the enclosed ferrite core before you connect the CA-560 Compact Power

Adapter to the camcorder.

Attach the ferrite core to the cable about 4 cm from the plug end (the plug to be connected to the camcorder) of the CA-560 Compact Power Adapter.

• Pass the cable through the centre of the core and wrap it around the core once, then close the unit until it clicks shut.

Mastering

the Basics

CA-560 Compact Power Adapter

Downloaded From VideoCamera-Manual.com Manuals

Powering Your Camcorder

Before operating your camcorder, you will need to use the power adapter to:

Provide power from a mains outlet

Charge a battery pack

Notes:

• The power adapter converts current from a household power socket (100–240 V AC, 50/60 Hz) to the DC current used by your camcorder.

• If the adapter is used next to a TV, it may cause bars to appear on the TV — move the adapter away from the TV or the aerial cable.

Connecting the camcorder to a mains outlet

POWER

CAMERA

OFF

PLAY(VCR)

the Basics

Mastering

Use the power adapter to provide your camcorder with instant power from a mains outlet. Always turn the camcorder off before connecting/removing the power source.

1. Set the POWER switch to OFF.

2. Connect the power adapter to the camcorder’s DC IN terminal.

3. Connect the power cable to the power adapter.

4. Plug the power cable into a mains outlet.

5. Disconnect the power adapter from the camcorder after use.

Unplug the power cable from the mains outlet, then disconnect it from the adapter.

Downloaded From VideoCamera-Manual.com Manuals

CAMERA

OFF

POWERPOWER

CAMERA

OFF

PLAY(VCR)

POWERPOWER

DC IN

9.5V

CHARGE

Attaching and charging the battery packs

CHARGE indicator

Mastering

the Basics

Your battery pack was partially charged before it left the factory. It should have enough power for you to check that your camcorder is working properly. However, you must charge the battery pack fully if you want it to power the camcorder for more than a few minutes. Always turn the camcorder off before connecting/removing the battery.

1. Set the POWER switch to OFF.

2. Attach the battery to the camcorder.

• Remove the battery pack’s terminal cover.

• Rotate the viewfinder upwards.

• With the triangle on the battery pack pointing downwards, align the edge of the battery pack with the line on the camcorder, press lightly and slide the battery down until it clicks into place.

3. Connect the power adapter to the camcorder.

4. Connect the power cable to the adapter and plug it into a mains outlet.

• The charge indicator flashes red to show that charging is in progress. Single

flashes mean that the battery pack is less than 50% charged. Double flashes mean that it is more than 50% charged. The indicator glows steadily when the battery pack is fully charged. If the indicator blinks rapidly and continuously (twice a second), the battery pack may be defective.

• The battery pack will also charge when the POWER switch is turned to

positions other than OFF. The CHARGE indicator may flash.

5. When charging is complete, disconnect the power adapter from the camcorder. Unplug the power cable from the mains outlet, then disconnect it from the adapter.

Downloaded From VideoCamera-Manual.com Manuals

6. Remove the battery pack after use.

• Rotate the viewfinder upwards.

• Press and hold the BATT. RELEASE button while you slide the battery up.

Notes:

• Never connect an unspecified product to the camcorder’s DC terminal. Likewise, do not connect the power adapter to an unspecified product.

• You can find detailed notes for using the batteries in the “Notes on Using the Batteries” ( 98). These notes include charging and recording times and how to install the backup battery.

CA-560 Compact Power Adapter

Specifications

Power supply 100–240 V AC, 50/60 Hz Power consumption 34 W Rated output 9.5 V, 2.7 A DC Operating temperature range 0°C–40°C (32°F–104°F) Dimensions 57 × 28 × 104 mm (2 1/4 × 1 1/8 × 4 1/8 in) Weight 180 g (6 3/8 oz) (without power cable)

the Basics

Mastering

Weight and dimensions are approximate. Errors and omissions excepted. Subject to change without notice.

Downloaded From VideoCamera-Manual.com Manuals

Using the Charge Adapter CR-560 Kit (optional)

The Compact Power Adapter CA-560 included with the camcorder can be used along with the CR-560 Kit for 3 different ways to power the camcorder or charge battery packs:

1. Charge the BP-500 Series battery packs with power from your car battery.

2. Operate the camcorder with power from your car battery.

3. Charge the BP-500 Series battery packs from a household mains outlet.

The Charge Adapter/Car Battery Cable Kit CR-560 includes the following:

Mastering

the Basics

Charge Adapter

Car Battery Cable

1. Charge the BP-500 Series battery packs with power from your car battery.

1 or 2 battery pack(s) + Charge Adapter + Car Battery Cable → car’s cigarette lighter

CHARGE

• Fast charging for the high-capacity BP-522 and BP-535 (both optional). Fifteen minutes of charging gives 70 minutes of recording (using the viewfinder).

Time required for full charge

from car battery or a mains outlet BP-508 1 hr. 20 min. BP-512 (optional) 1 hr. 20 min. BP-511 (optional) 1 hr. 20 min. BP-522 (optional) 1 hr. 40 min. BP-535 (optional) 2 hr. 30 min.

Downloaded From VideoCamera-Manual.com Manuals

DC Cable

To car’s cigarette lighter

2. Operate the camcorder with power from your car battery.

Camcorder + DC Cable + Charge Adapter + Car Battery Cable → car’s cigarette lighter

To car’s cigarette lighter

3. Charge the BP-500 Series battery packs from a mains outlet.

1 or 2 battery pack(s) + Charge Adapter + Compact Power Adapter

CHARGE

• Fast charging for the high-capacity BP-522 and BP-535 (both optional). Fifteen minutes of charging gives 70 minutes of recording (using the viewfinder).

the Basics

Mastering

Note:

• For full details of how to use the CR-560, refer to its instruction manual.

Downloaded From VideoCamera-Manual.com Manuals

Loading a Cassette

OPEN/EJECT

PUSH

Only use videocassettes marked with the D logo.*

Mastering

the Basics

Loading and unloading

1. Make sure that you have attached a power source.

2. Slide the OPEN / EJECT 5 switch (on the bottom of the

camcorder) to release the cassette compartment cover.

• Pull the cover fully open (while holding the button) and wait a couple of seconds for the cassette compartment to open automatically.

• The confirmation beep sounds when the cassette cover fully opens.

3. Load or unload the cassette.

• Insert the cassette gently with the window facing the grip belt, and the REC/SAVE tab up.

• Remove the cassette by pulling it straight out.

4. Press the P mark on the compartment until it clicks, and wait

for it to close.

5. Click the cover back into place.

* D is a trade mark.

Notes:

• Do not interfere with the cassette compartment while it is opening or closing automatically, and do not attempt to close the cover until the cassette compartment has fully retracted.

• After loading a cassette, use record search ( 38) to find the point where you want to start recording.

• Be careful not to get your fingers caught in the cassette compartment cover.

• Do not leave the cassette in the camcorder after use — return it to its case and store it in a cool, clean, dry place.

• When you turn the camcorder’s power on, v flashes in the display until you load a cassette.

• With some types of tapes, the remaining tape display may not give an accurate

Downloaded From VideoCamera-Manual.com Manuals

reading ( 112).

Protecting tapes from accidental erasure

SAVE

REC

SAVE

REC

To protect your recording from accidental erasure, slide the tab on the cassette so that it exposes the hole. (This switch position is usually labelled SAVE or ERASE OFF.) If you load this cassette and put the camcorder in record pause mode ( 18), “THE TAPE IS SET FOR ERASURE PREVENTION” is displayed for approx. 4 seconds and then the v mark flashes in the display. If you want to record on the cassette again, slide the tab back so the hole is closed.

Handling cassettes

• To protect the tape heads, transfer cassettes directly from the tape case to the camcorder — do not open the tape protect cover or touch the tape itself.

• Do not use cassettes where the tape has been damaged or spliced — they may damage the camcorder.

• Do not insert anything into the small holes on the cassette or cover them with cellophane tape.

• Handle cassettes with care — dropping them or exposing them to external shocks may cause internal damage.

• Store cassettes in the provided case, first rewinding them to the start of the tape and then storing them upright.

• A cassette with metal plated terminals may become dirty with use, affecting information transfer. Therefore, after using a tape about 10 times, be sure to clean the terminals with a cotton bud.

the Basics

Mastering

Cassette memory

You are unable to use the cassette memory function with this camcorder.

Downloaded From VideoCamera-Manual.com Manuals

Basic Recording

4, 5

POWER

CAMERA

PLAY(VCR)

POWER

CAMERACAMERA

PLAY(VCR)

OFF

Mastering

the Basics

Before you start recording

Have you completed the following steps?

• Attached a power source ( 11).

• Removed the lens cap ( 96).

• Fasten the grip belt ( 96).

• Chosen the display: viewfinder ( 96) or LCD screen ( 25).

Notes:

• When you’re using the viewfinder, fully close the LCD or rotate the LCD so that it faces the same direction as the lens ( 25).

• When using the viewfinder with the BP-522 or BP-535 Battery Pack (both optional) attached, extend the viewfinder and rotate it to a comfortable angle.

You may also want to install the backup battery ( 100) in order to set the date and time display ( 46).

To record

1. Press the small button on the POWER switch and hold, turn the POWER switch to CAMERA.

• The camcorder automatically sets to record pause mode. PAUSE appears in

the display.

• If you haven’t set the date and time display, SET THE TIME ZONE, DATE

Downloaded From VideoCamera-Manual.com Manuals

AND TIME appears in the display. For setting the time zone, see p. 46. For setting the date and time, see p. 48.

• The camcorder power indicator lights up.

• The confirmation beep sounds.

• The camcorder will turn itself off if you leave it in record pause mode for

more than about 5 minutes. To return to record pause mode, turn the POWER switch to OFF and then back to CAMERA.

2. Load a cassette ( 16).

3. Slide the program selector to [.

• This selects the camcorder’s Easy Recording program. It allows you to

simply point and shoot without making any manual adjustments ( 52).

4. Press and release the start/stop button once to begin recording.

• For still image recording to a cassette, see p. 49.

5. Press and release the start/stop button again to pause recording.

• The camcorder returns to record pause mode and PAUSE reappears in the

display.

• You can stop and restart recording as often as you like by pressing the

start/stop button.

Note:

• After loading a cassette, start recording when the tape counter has stopped.

When you have finished recording

• Replace the lens cap.

• Return the viewfinder to its retracted position.

• Return the LCD screen flush to the camcorder body.

• Unload the cassette.

• Turn the POWER switch to OFF.

• Disconnect the power source.

Notes:

• To check that the camcorder is recording correctly, make a test recording first.

• Before making important recordings, clean the video heads using a Canon DVM-CL Digital Video Head Cleaning Cassette or a commercially available digital video head cleaning cassette.

• To close the LCD panel, rotate it vertically until the screen faces you, then press the upper right corner until it clicks securely closed.

• You cannot monitor the sound from the speaker when recording.

• For tips on how to make better videos, see p. 36.

• For extra recording time, set REC MODE to LP ( 20).

the Basics

Mastering

Downloaded From VideoCamera-Manual.com Manuals

REC MODE••••SP

VCR SET UP

PLAY

(VCR)

CAMERA

Changing the recording mode

You can record and play back a tape in SP (standard play) and LP (long play) modes. LP extends tape usage by 1.5 times.

You can’t add sound (audio dubbing) or images (AV insert) to a tape that has been recorded in a mode other than SP mode. If you plan to use either of these functions later, record in SP mode.

MV500i

( 39)

Mastering

the Basics

To change to LP mode, open the menu and select VCR SET UP. Then select REC MODE, set it to LP and close the menu.

Notes:

• When recording and playing back tapes in LP mode, the nature of the tape and usage conditions may affect recording, mosaic-like noise may appear in the image and the sound may be distorted during playback. For important recordings, therefore, set the camcorder to SP mode.

• We recommend recording in SP mode when you plan to transfer images taken with the camcorder to your PC.

• If you record in both modes on the same tape, the picture may become distorted during playback and the time code may not be written correctly.

• A tape recorded in LP mode on other digital equipment may produce the mosaic-like noise and the sound may become distorted when playing back on this camcorder.

• A tape recorded in LP mode on this camcorder may produce the mosaic-like noise and the sound may become distorted when playing back on other digital equipment.

Downloaded From VideoCamera-Manual.com Manuals

16:9 (Wide screen TV recording)

16:9••••••••OFF

CAM.SET UP

BEEP••••••••ON

SYSTEM

PLAY

(VCR)

CAMERA

Produces images in the 16:9 format for playback on wide screen TVs.

CAMERA

( 39)

To switch 16:9 to ON, open the menu and select CAM.SET UP. Then select 16:9, set it to ON and close the menu.

Notes:

• “16:9” is shown in the display when you switch the 16:9 mode on.

• You cannot use the 16:9 mode with the Easy Recording program.

• If you play back a recording made for 16:9 on a normal TV screen, the image

will appear to be vertically “squashed” (compressed).

Confirmation/Warning beeps

The camcorder’s short operation confirmation beeps are indicated by ` in the illustrations. Beeps sound upon certain camcorder operations such as when you turn the camcorder on, during the self-timer countdown, right before the camcorder’s automatic shut-off, and also upon any unusual condition of the camcorder. Beeps are not recorded on the tape.

the Basics

Mastering

( 39)

To turn the beep off, open the menu and select SYSTEM. Then select BEEP, set it to OFF and close the menu.

Downloaded From VideoCamera-Manual.com Manuals

CAMERA

Demonstration mode

You can see a demonstration of the camcorder’s main features. To see the demonstration, do either of the following:

• With no cassette inserted, turn the DEMO MODE on in the CAMERA menu and close the menu.

• Leave the camcorder with no cassette inserted for five minutes after turning it on.

( 39)

Mastering

the Basics

DISP.SET UP

DEMO MODE••••ON

To turn the demonstration mode off, open the menu and select DISP. SET UP. Then select DEMO MODE, set it to OFF and close the menu.

Note:

• To cancel the demo mode once it has begun: push any button, turn off the power or load a cassette.

Downloaded From VideoCamera-Manual.com Manuals

Zooming

D.ZOOM••••••

72×

CAM.SET UP

CAMERA

Zoom in

Zoom out

18× optical zoom

The camcorder’s zoom lens allows you to choose the best picture angle for each scene:

• Move the zoom control towards W to zoom out to wide-angle.

• Move it towards T to zoom in to telephoto.

You can also control the speed of zooming:

• Move the control slightly to zoom slowly.

• Move it farther to zoom more quickly. (The farther you move the zoom control, the faster the zoom speed.)

The T and W buttons on the wireless controller adjust the picture angle, but not the zoom speed.

the Basics

Mastering

72×/360× digital zoom

Magnifies the camcorder’s zoom range by up to 20× in CAMERA mode. The zoom control continues to work as usual. You can freely zoom in and out between 1× and 360× magnification — the camcorder automatically switches between optical zooming (up to 18×) and digital zooming (18× to 72× or 18× to 360×).

( 39)

To change the digital zoom, open the menu and select CAM.SET UP. Then select D.ZOOM, set it to OFF or 360

Downloaded From VideoCamera-Manual.com Manuals

× and close the menu.

Mastering

Notes:

• When zooming, as a rule, keep at least 1 m (3 ft 33/8 in) between you and your subject. However when the zoom is at the wide-angle position, you can focus on a subject as close as 1 cm (3/8 in).

• Image resolution is slightly lower when the magnification is greater than 18×.

• You cannot use digital zoom in the Night recording program.

• The zoom indicator appears for 4 seconds. When the digital zoom is set to 72×, the zoom indicator extends (light blue). When the digital zoom is set to 360× zoom, the zoom indicator extends again (a darker blue).

the Basics

Downloaded From VideoCamera-Manual.com Manuals

Using the LCD Screen

90°

180°

90°

Opening and closing the LCD screen

Slide the LCD panel OPEN button and open the panel by pulling it away from the camcorder. This automatically switches the LCD screen on and the viewfinder off. To close the LCD panel, press the upper right corner until it clicks securely closed. When you close the LCD panel, the LCD screen automatically switches off and the viewfinder switches back on.

Changing the angle of the LCD screen

You can choose the angle of the screen that suits you best by opening and rotating the screen, also you can rotate the LCD screen so that faces in the direction of the lens ( 27).

the Basics

Mastering

You can also push the panel flat against the camcorder until it is flush with the side, with the screen facing outwards.

Notes:

• Avoid touching the LCD screen when moving the LCD panel.

• Do not hold the camcorder by the LCD panel or the viewfinder.

• Make sure you open the LCD panel at 90°, before attempting to rotate it.

Downloaded From VideoCamera-Manual.com Manuals

BRIGHTNESS••

DISP.SET UP

–+

PLAY

(VCR)

CAMERA

• Always rotate the LCD panel vertically into place, before closing it or pushing

it flat against the side of the camcorder.

• Always fully close the LCD panel until it clicks securely.

• Be careful not to leave the LCD, viewfinder or lens exposed to direct sunlight outdoors or in a window. Doing so could cause damage.

• Bright light falling on the LCD screen may cause glare that makes it difficult for you to view the image. In this case, switch to using the viewfinder. You are also able to adjust the brightness of the screen (see “Adjusting the LCD screen” below).

Adjusting the LCD screen

You can adjust the brightness of the LCD screen.

Mastering

the Basics

( 39)

Open the menu and select DISP.SET UP from the menu. Then select BRIGHTNESS, adjust the level with the selector dial and close the menu.

A bar showing the level appears in the display.

• Turn the selector dial up to make the display brighter.

• Turn the selector dial down to make the display darker.

Notes:

• The camcorder will remember your brightness setting even after you turn it off.

• The brightness of the LCD does not affect that of the recorded images or the viewfinder.

About the LCD Screen

The LCD screen built into this camcorder is a high precision product. However, small black dots or bright points of light (red, blue or green) may appear constantly on the LCD screen. This is not a malfunction of the LCD screen and they are not recorded on the tape. (Effective dots: more than 99.99%)

Downloaded From VideoCamera-Manual.com Manuals

Allowing the subject to monitor recording

MIRROR••••••ON

DISP.SET UP

CAMERA

When you turn the LCD panel so that it faces the same direction as the lens, you can watch yourself during recording or let your subject monitor recording. The viewfinder is also activated when the panel is in this position. (Adjust the viewfinder,

96)

• You can choose the display style, reversed (mirror on) or not (mirror off). The recording itself is unaffected regardless of which one you choose.

( 39)

To turn the mirror mode off, open the menu and select DISP.SET UP. Then select MIRROR, set it to OFF and close the menu.

The indicators that appear in the LCD display when MIRROR is turned on:

the Basics

Mastering

REC REC PAUSE EJECT

• These and all other indicators appear normally in the viewfinder.

Downloaded From VideoCamera-Manual.com Manuals

Self-timer ( 63)

Playing Back a Cassette

POWER

CAMERA

PLAY(VCR)

OFF

REC

FOCUS

AE SHIFT

You can use the LCD screen for instant, on-the-spot playback. The camcorder also

Mastering

the Basics

plays back the sound track via the built-in speaker ( 31).

• When you play back a tape, you can also close the LCD panel with its screen side facing up.

• When you’re using the viewfinder to view playback, close the LCD panel.

To play back your recordings on a TV, see p. 32. To use the wireless controller, see p. 43.

Note:

• To avoid accidental recording, make sure that you slide the tab on the cassette so that it exposes the hole (the switch position is usually labelled SAVE or ERASE OFF).

1. Attach a power source and turn the POWER switch to PLAY

(VCR).

• The power indicator lights up.

2. Load the cassette.

3. Press the e (play) button to start playback.

• To end playback, press the 33(stop) button.

• To wind the tape forwards, stop playback and press the button.

• To wind the tape backwards, stop playback and press the button.

• If the playback picture is rough (mosaic-like noise), clean the video heads using a Canon DVM-CL Digital Video Head Cleaning Cassette or a commercially available digital video head cleaning cassette.

Downloaded From VideoCamera-Manual.com Manuals

(fast forward)

(rewind)

Other playback modes

REW

PLAY

STOP

PAUSE

SLOW

×2

+ /

– /

Playback pause

Press the aa(pause) button. To resume normal playback, press it again, or press the ee(play) button. The camcorder automatically goes into stop mode after about 5 minutes’ playback pause.

Fast forward playback

To play back the recording at about 11.5 times normal speed, press and hold the

(fast forward) button during normal playback or press and hold the

(fast

forward) button during normal fast forward.

Rewind playback

For reverse playback at about 11.5 times normal speed, press and hold the

(rewind) button during normal playback or press and hold the

(rewind)

button during normal rewind.

Special playback

Frame Advance

To play back frame by frame, press the +/ ae button repeatedly during playback pause. Press and hold to play back continuous frame advance.

the Basics

Mastering

Frame Reverse

To play back in reverse frame by frame, press the –/4a button repeatedly during playback pause. Press and hold to play back continuous frame reverse.

Slow Forward Playback

To play back at about 1/3 normal speed, press the SLOW M button during normal playback. Press the PLAY e button to return to normal playback.

Slow Reverse Playback

To play back in reverse at about 1/3 normal speed, press the –/4a button and then the SLOW M button during normal playback. Press the PLAY e button to return to normal playback.

Downloaded From VideoCamera-Manual.com Manuals

Reverse Playback

To play back in reverse at normal speed, press the –/4a button during normal forward playback. Press the PLAY e button to return to normal forward playback.

• The camcorder automatically goes into stop mode after about 2 minutes of paused reverse playback.

Forward ×2 Playback

Press the ×2 button during normal playback. Press the PLAY e button to return to normal playback.

Reverse ×2 Playback

Mastering

the Basics

Press the –/4a button and then the ×2 button during normal playback. Press the PLAY e button to return to normal playback.

Notes:

• Mosaic-like noise appears on the screen during some of the special playback modes.

• There’s no audio during special playback.

Downloaded From VideoCamera-Manual.com Manuals

+ 92 hidden pages

Canon 7561A001 User Manual

Important Usage Instructions

Contents

Thank you for Choosing a Canon

Introducing the MV500/MV500i

Finding Your Way Around the MV500/MV500i

Attaching the Ferrite Core

Powering Your Camcorder

Loading a Cassette

Basic Recording

Zooming

Using the LCD Screen

Playing Back a Cassette