Canon 0284B002 User Manual
Canon
EF~
LENS
EF-S60mm
»
ULTRASONIC
f/2.8
MACRO
USM
Instruction
Mode d'emploi
Bedienungsanleitung
Instrucciones
Istruzioni
~ffl*.~~,~~~~~*m~~o
~~m~~~~*~,
~.~*~~o
Thank you for purchasing a Canon USM lens.
The Canon EF-S60mm f/2.8 MACRO
is
a macro lens
photography
or
life-size magnification. It has been
developed
compatible
"USM" stands for Ultrasonic Motor.
that
can be used
and close-up picturesupto
for
use
with
with
digital SLR cameras*
EF-S lenses.
for
USM
normal
lens
1:1,
Features
1.
The three-group floating system results
sharp and clear delineation at all focusing
distances from life-size to infinity.
2.
A Canon macro flash (sold separately) makes
it easy to take close-up pictures with a flash.
The inner focusing mechanism enables AF
photography while the macro flash
attached.
3.
USM for fast, quiet focusing.
4.
Manual focusing availableinautofocusing
mode (ONE SHOT AF).
is
in
E-1
~
Safety Precautions
1.Donot
2.
look
at the
sunora
through
the
result
through the lens
Whetheritis
not
lensorcamera. Doing so could
in
loss of vision. Looking at the sun directly
is
especially hazardous.
attachedtothe cameraornot,
leave
the
lens under the
bright
sun
light
without
source
the
lens cap attached. This is to prevent the lens
from concentrating the sun's rays, which could
cause a fire.
~
Handling Cautions
If the lensistaken
a warm one, condensation may develop
fromacold
environment
on the
into
lens surface and internal parts. To prevent
condensation in this case, first put the lens into
an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually.
Do
the same when taking the
lens from a warm environment into a cold one.
This device complies with Part 15 of the FCC Rules. Operation
subject to the following two conditions:
cause harmful interference, and
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
(1)
This device may not
(2)
this device must accept any
E-2
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
do
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radiorrV technician for
help.
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus as set out in the
interference-causing equipment standard entitled "Digital
Apparatus", ICES-003 of the Industry Canada.
is
The C€ Mark is a Directive conformity mark of the
European Community (EC)
CE:
in
accordance with the
N118
in
Nomenclature
Hood mount (-7
Focusing ring (-7 4)
Filter mounting
thread
(-7
9)
"..----
Lens mount index
Distance index
Focus mode switch
(-74)
Contacts
(-74)
(-74)
For detailed information, reference page numbers are providedinparentheses (-7 **).
E-3
Mounting
and
Detaching
the
Lens
See your camera's instructions for details on
mounting and detaching the lens.
<$
After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
1$
If the contacts get soiled, scratched,orhave
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
'*'
If the contacts get soiled or have fingerprints
them, clean them with a soft cloth.
If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the
in
the diagram, and turn clockwise. To remove
it, reverse the order.
E-4
0 index of the dust cap as shown
on
To
shoot in autofocus mode, set the focus mode
switch to AF.
To
use only manual focusing, set the focus mode
switch
to
ring.
of
[l]AfterautofocusinginONESHOTAFmode,focus
MF, and focusbyturning the focusing
The
focusing ring always works, regardless
the focus mode.
manuaUyby pressing the shutter button halfway
and turning the focusing ring. (Full-timemanOal
focus) ,
Loading...