9160
10 Gigabit Ethernet
Network Interface Device
User Manual
NOTICE
Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as
a guide for the proper installation, operation and/or maintenance of Canoga Perkins equipment. The
drawings, specifications and information contained in this document are the property of Canoga
Perkins and any unauthorized use or disclosure of such drawings, specifications and information is
prohibited.
Canoga Perkins reserves the right to change or update the contents of this manual and to change the
specifications of its products at any time without prior notification. Every effort has been made to
keep the information in this document current and accurate as of the date of publication or revision.
However, no guarantee is given or implied that the document is error free or that is accurate with
regard to any specification.
Canoga Perkins Corporation
20600 Prairie Street
Chatsworth, California 91311-6008
Business Phone: (818) 718-6300
(Monday - Friday 7 a.m. - 5 p.m. Pacific Time)
FAX: (818) 718-6312 (24 hrs.)
Web Site: www.canoga.com
Email: fiber@canoga.com
Copyright © 2005 - 2007 Canoga Perkins Corporation
All Rights Reserved
Model 9160 10 Gigabit Ethernet Network Interface Device
User Manual
Model Number 9160-UM
Product Number 6913205
Rev. C 01/2008
CAUTION!
This product may contain a laser diode operating at a wavelength of 1300 nm - 1600 nm. Use of
optical instruments (e.g., collimating optics) with this product may increase eye hazard. Use of
controls or adjustments, or performing procedures other than those specified herein may result in
hazardous radiation exposure.
Under normal conditions, the radiation levels emitted by this product are under Class 1 limits in 21
CFR Chapter 1, Subchapter J.
ATTENCION!
Cet équipement peut avoir une diode laser émettant à des longueurs d'onde allant de 1300nm à
1600nm. L'utilisation d'instruments optiques (par exemple : un collimateur optique) avec cet
équipement peut s'avèrer dangereuse pour les yeux. Procéder à des contrôles, des ajustements ou toute
procédure autre que celles décrites ci-après peut provoquer une exposition dangereuse à des
radiations.
Sous des conditions normales, le niveau des radiations émises par cet équipement est en dessous des
limites prescrites dans CFR21, chapitre 1, sous chapitre J.
NOTICE!
This device contains static sensitive components. It should be handled only with proper ElectroStatic
Discharge (ESD) grounding procedures.
NOTE!
Cet équipement contient des composants sensibles aux décharges électro-statiques. Il doit absolument
être manipulé en respectant les règles de mise à la terre afin de prévenir de telles décharges.
Table of Contents
Overview...................................................................................................................1-1
Set-up and Installation ............................................................................................2-1
Install the 9160....................................................................................................................................2-1
Power-Up, Hardware Functions, and LEDs........................................................................................2-2
Alarms...........................................................................................................................................2-3
Remote Fault.................................................................................................................................2-4
Using the Software...................................................................................................3-1
Setting Up for Network Management .................................................................................................3-1
Set Up the Network Management Platform ..................................................................................3-1
Set Up the PC for Terminal Operation.........................................................................................3-2
Management User Interface ................................................................................................................3-2
General Screen Format.................................................................................................................3-2
User Interface Organization.........................................................................................................3-4
Login and the Main Menu.............................................................................................................3-5
Managing the 9160..............................................................................................................................3-5
Configure the 9160 for the System................................................................................................3-5
View Device and Module Information..........................................................................................3-6
Manage the Date and Time...........................................................................................................3-7
Manage SNMP and Host Access...................................................................................................3-7
Manage Traps and Alarms............................................................................................................3-8
View System Events and Traps .....................................................................................................3-9
Control Management Packets.......................................................................................................3-9
Update Software .........................................................................................................................3-10
Managing Security ............................................................................................................................3-10
Set General Security Parameters................................................................................................3-11
Set Up User Accounts .................................................................................................................3-12
Change Your Password...............................................................................................................3-13
Manage Logged In Users............................................................................................................3-13
Set Up Host Access .....................................................................................................................3-14
Set Up the Notification Destination for Traps............................................................................3-14
Managing the Network Interface.......................................................................................................3-16
Check and Update Port Information...........................................................................................3-17
Set Up Spanning Tree Parameters..............................................................................................3-17
Set Up LAGs................................................................................................................................3-18
Set Up VLANs .............................................................................................................................3-19
Set Up Optional Double Tagging ...............................................................................................3-20
Set Up Multiple Spanning Tree Parameters ...............................................................................3-20
Check Global Spanning Tree Data.............................................................................................3-20
Check the Forwarding Database................................................................................................3-21
Check the Static ARP Table........................................................................................................3-21
Maintenance and Troubleshooting.........................................................................4-1
9160 10 Gigabit Ethernet Network Interface Device i
General Maintenance and Managing Cable Links.............................................................................. 4-1
Checking Optical Power Levels..........................................................................................................4-1
Measure Transmitter Output Power............................................................................................. 4-2
Measure Receiver Input Power....................................................................................................4-2
Measure Fiber Link Attenuation ..................................................................................................4-3
Troubleshooting..................................................................................................................................4-3
New Installation ...........................................................................................................................4-4
Problems With Fiber Optics.........................................................................................................4-4
Running Diagnostics...........................................................................................................................4-4
Test Latency and Jitter ................................................................................................................. 4-4
Test a Connection With PING......................................................................................................4-5
Specifications.............................................................................................................5-1
9160 Specifications.............................................................................................................................5-1
9160 Interface Model Numbers .......................................................................................................... 5-2
Warranty Information...........................................................................................A-1
Acronym and Abbreviation List ........................................................................... B-1
List of Figures
Figure 1. The 9160 Front Panel ......................................................................................................... 1-1
Figure 2. Remote Fault Signal........................................................................................................... 2-4
Figure 3. General Screen Format.......................................................................................................3-3
Figure 4. Typical Spanning Tree Application.................................................................................. 3-16
List of Tables
Table 1. 9160 Management LEDs ..................................................................................................... 2-2
Table 2. 9160 Interface LEDs............................................................................................................ 2-3
Table 3. 9160 Main Menu.................................................................................................................. 3-5
Table 4. Trap Configuration Options.................................................................................................3-9
Table 5. Network Spanning Tree Parameters Options..................................................................... 3-16
ii 9160 10 Gigabit Ethernet Network Interface Device
Overview
The 9160 10 Gbps Ethernet Network Interface Device that provides intelligent optical demarcation
and terminates managed transport at the point of delivery, including in a multi-tenant environment. In
addition, it offers multiple levels of security, Layer 2 statistics, remote software upgrade, remote
control and monitoring, and management through CanogaView.
The 9160 supports one port that receives and transmits 10 Gigabit Ethernet data over single mode
fiber (SMF) or multimode fiber (MMF) at 850, 1310, or 1550 nm wavelength, up to four single-port
modules that receive and transmit 10/100/1000BASE Ethernet data on SMF or MMF, and a multipleport (MP) module with eight ports that receive and transmit 10/100/1000BASE Ethernet data on SMF
or MMF. The hot-swappable, plug-in interface modules can include auto-ranging UTP input with
configurable optical output or can support specific UTP and optics options; for a list of interfaces
with options, see Chapter 5, Specification.
In addition to the data ports, the 9160 front panel, shown in Figure 1, includes:
• Console port for management through VT100 emulation
• LEDs for system management and various module functions; for details, see Chapter 2
• Reset switch
Figure 1. The 9160 Front Panel
9160 10 Gigabit Ethernet Network Interface Device 1-1/(1/2 Blank)
Set-up and Installation
This section describes how to set up and install the 9160. Before setting up the 9160, make sure the
serial cable (required to connect the chassis to a VT100 type terminal or PC) is available.
Install the 9160
The 9160 is tested and inspected before shipment from the factory. If there is obvious damage to the
shipping container, contact the carrier immediately.
Caution: Follow electrostatic discharge (ESD) safety precautions when handling Canoga
Perkins products, as with all electronic devices with static sensitive components.
1. Unpack the 9160. Keep the shipping container until the unit is installed and fully operational. In
the unlikely event that the unit is defective, contact Canoga Perkins Customer Service for a return
authorization number (RMA) and instructions on return shipment. For details, see Appendix A.
2. Mount the 9160 in a rack or as a standalone unit.
• Use the standard rackmount kit with brackets and screws to install the 9160 in a 19-inch rack or
use the optional 23-inch rackmount kit. The 9160 includes two sets of mounting holes.
• For a front chassis mount, align the screw holes in the brackets with the screw holes at the
front of the side panel of the 9160, then secure the screws.
• For a mid- or recessed chassis mount, align the screw holes in the brackets with the screw
holes in the middle of the side panel of the 9160, then secure the screws.
• To use the 9160 as a standalone unit, place it on a secure, flat surface within reach of the power
and fiber optic connections
3. Connect the power. The 9160 can be equipped for either AC or DC power.
• Plug the AC power cord into the socket at the rear of the 9160 and the wall socket.
Caution: Reversing the connections can damage both the DC source and the 9160.
• Connect power for the -48 VDC power supply at the terminal block; use 18 ga wire for the
+ and - connections and 20 ga wire for the gnd connection.
4. If not already installed, plug the XFP(s) into the 10G 1 port; the slot is keyed. To remove an
XFP, either lift the bail or press the button on the SFP, then gently pull it out.
5. If not already installed, slide an SP or the MP module into the rails and push it firmly into the
backplane, then tighten the captive screw(s).
Cabling for the 9160 includes the serial cable to the Terminal port, the Ethernet cable for a UTP port,
and the fiber optic link to the Tx and Rx ports.
6. Plug the serial cable into the serial port on the front panel and your PC. For the pinout, see
Chapter 5, Specifications.
9160 10 Gigabit Ethernet Network Interface Device 2-1
Dirty optical connectors are a common cause of link loss or attenuation problems, especially for SMF.
Clean the connectors before plugging in a cable and whenever there is a significant or unexplained
light loss. To prevent contamination, always install protective dust covers on unused fiber optic
connectors.
7. Wipe the ferrule and the end-face surface of the male fiber coupler with a lint-free, isopropyl
alcohol pad from a fiber cleaning kit.
8. Use canned air to blow any dust out of the female fiber coupler.
Caution: To avoid damaging the fiber end-surface or connector, use extreme care when
installing or removing cables.
9. Plug in the optical cables with Tx to Rx, Rx to Tx orientation.
Caution: To protect a UTP Ethernet port from an intrabuilding lightning surge, use a properly
grounded shielded cable.
10. If your 9160 includes a UTP port, plug in the UTP Ethernet cable with RJ-45 connector.
11. Label each cable and connector with the signal name and direction.
Canoga Perkins recommends that you determine and record link attenuation and transmission power
before starting normal link traffic. The attenuation factor and transmission power identify potential
problems with links near the lower limit of receiver limitations. For details on link attenuation and
transmission power, see Chapter 4.
Power-Up, Hardware Functions, and LEDs
During the initial power-up sequence, all LEDs light amber. When start-up is complete and data is
transmitting normally across the link, the MGR, FAN, and power LEDs light green and the Rx and
Tx LEDs for all ports light or blink green when they transmit or receive data.
The LEDs on the front panel show the system and port conditions. The MGR LED shows the
management conditions; see Table 1. Each interface module includes from two to six LEDs; Table 2
lists all possible LEDs. For details about the LEDs, see your interface module and Tables 1 and 2.
Table 1. 9160 Management LEDs
LED Status Description
P1 (Primary) or Off No power or power supply not installed
P2 (Secondary) Power Green Normal operation
Amber System self-test
Red Power failure or Major alarm
FAN Green Normal operation
Amber System self-test or one fan failed
Red Power failure
Red blinking Fan not installed
2-2 9160 10 Gigabit Ethernet Network Interface Device
LED Status Description
MGR Off No power
Green Normal operation
Green blinking Management traffic
Amber System self-test or over-temperature trap or alarm
Amber blinking Management traffic with over-temperature trap or alarm
Red Diagnostic or CPU failure
Table 2. 9160 Interface LEDs
LED Status Description
TX Off No transmission activity
Green blinking Transmission activity
Amber System self-test
Red Port disabled; may be due to Link Loss Forwarding
(LLF)
RX Off No link
Green Link established; full duplex (if available)
Green blinking Receiving activity; full duplex (if available)
Amber System self-test; half duplex (if available)
Amber blinking Half duplex (if available) receiving activity
Red Receiving Remote Fault
NET Off Non-network connection
Green Network connection
Amber System self-test
SPD Off 10BaseT data rate
Amber 100BaseT data rate or system self-test
Green 1000BaseT data rate
Red Port disabled
Alarms
The 9160 can generate Traps and Major and Minor Alarms. For details about the Traps Log and
setting up notification, see Chapter 3.
9160 10 Gigabit Ethernet Network Interface Device 2-3
Remote Fault
The 9160 supports Remote Fault (RMTF) on all MP and SP optical ports with speeds greater than
10 Mbps; it is not supported for the 10G XFP or UTP ports.
To use RMTF on a specific port, you must first enable it on both the local port and the remote device,
and then set that port speed to Auto-negotiation. To set RMTF and the port speed in software, see
page 3-17.
If RMTF is enabled on a port and that port Rx loses the signal, it sends an RMTF signal from its Tx,
the Rx LED is off, and an alarm flags the link loss on the Extension port; see Figure 2. When the
Extension port receives a Remote Fault signal, the Rx LED lights red and an alarm flags the remote
side optical link failure. RMTF complies with the IEEE802.3u Remote Fault standard.
• Local device Rx detects link loss
• Tx transmits RMTF to remote device
Usr
Prt
RxTx
Tx
RMTF
Ext
Prt
Rx
Usr
Prt
Rx
Local Device Remote Device
Ext
Prt
RxTx
Tx
• Local device Rx turns OFF
• Remote device Rx lights red
Figure 2. Remote Fault Signal
2-4 9160 10 Gigabit Ethernet Network Interface Device
Using the Software
You can manage the system through VT100 Terminal Emulation, which is accessible by a Telnet
session, HyperTerminal or similar terminal emulation software, a standard SNMP network manager,
and CanogaView.
Setting Up for Network Management
Typically, the 9160 runs within the network on an Ethernet connection, communicating with your
Network Management Platform.
Set Up the Network Management Platform
You must run several Management Information Bases (MIBs) on your Network Management
Platform in order to successfully manage this module. Before you start, check that these industrystandard MIBs are loaded:
• Standard MIB
• Dot2sd.mib
• Etherlike.mib
• If.mib
• Bridge.mib
• Pbridge.mib
In addition, download these private mibs, available from the Canoga Perkins web site; go to
www.Canoga.com, click Support, then click Software Download, and follow the prompts on screen.
• Cp.mib Supports all Canoga Perkins products
• Cpsysinf.mib Supports SNMP access
• Cphost.mib Supports Host Table and Host Access functions
• Cptraptb.mib Supports the Trap Table
Setting up the VT100 session depends on which connection, serial port or Ethernet, you have
available for access to the VT100 management program. Canoga Perkins suggests that you use
HyperTerminal for your first session. You must set up TCP/IP before you can use Telnet.
9160 10 Gigabit Ethernet Network Interface Device 3-1
Set Up the PC for Terminal Operation
These steps briefly describe how to set up your PC for a terminal connection. For details on using
Windows, see your Windows documentation.
1. Turn on your PC.
2. When the Windows desktop appears, click Start, then highlight Programs, Accessories, the
HyperTerminal Folder, and then click HyperTerminal.
3. At the Connection Description dialog, select an icon, enter a name for the connection to the
system, and click OK.
4. At the Connect To dialog, pull down the Connect using menu, select the COM port, and
click OK.
5. At the COM Properties dialog, on the Port Settings tab, check for these selections:
• Bits per second: 9600 bps
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
6. Click OK. HyperTerminal connects to the system and the VT100 terminal emulation starts.
Management User Interface
The Management User Interface for the 9160 provides screens for setup, monitoring, and diagnostics.
You can access the screens directly by connecting to the serial port of the 9160.
These sections discuss the screens for the 9160, using a Telnet session for access.
General Screen Format
A typical screen, shown in Figure 3, includes standard descriptions and reference designations. Use
this and other screens to configure the system, set operational parameters, and verify the system
status. All screens use a common method for navigation.
3-2 9160 10 Gigabit Ethernet Network Interface Device
Loading...