USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
SERVICE INSTRUCTIONS
Cannon
This heater is approved for use with Natural and Propane gases.
Please leave instructions with the owner
INBUILT MODELS
FITZIB-SDSEB-NG
FITZIB-SDSEB-LP
FITZROY INBUILT
2
Contents
Contents 2
Warranty 3
❍ Distributor
Safety warnings 4-5
❍ What to do if you smell gas
❍ Warnings
❍ Standards
User instructions 6-8
❍ Operating instructions
❍ Cleaning
❍ Flame characteristics
Heater specifications 9
Installation instructions 10-14
❍ Clearances
❍ Fitment of cabinet depth spacer
❍ Installation into a masonry/brick or mock fireplace
❍ Installation WITH a flue connected
❍ Installation WITHOUT a flue connected
❍ Sealing
Gas connections 15
Log installation 16
Gas control 17-18
❍ Gas pressure point
❍ Gas pressure adjustment
Installation tips 19
Trouble-shooting 20-21
❍ Connections
Service instructions 22-24
❍ General
❍ To replace the primary glass
❍ To replace outer glass
❍ To replace the gas control
❍ To replace the ignition (module) device
❍ To replace the room circulation fan
❍ To replace the fan pressure switch
❍ To remove the heat exchanger
❍ To replace the burner and spark/sense electrode
❍ Wiring diagram
❍ Data plate
❍ For service to this appliance
3
The Cannon appliance is warranted against defects in materials and
workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia.
Warranty service, which includes parts and labour for the replacement or
repair of defective parts, is available through the CANNON distributor.
(Details below or on page 23).
Consumers are responsible for service person’s travel outside normal service areas (approximately seventy (70k) radius from the nearest Cannon
dealer’s location), local cartage, and normal maintenance as described in
this manual.
Any product subjected to misuse, abuse, negligence, accident or alteration will have its warranty voided. The defacement of serial plate will have
its warranty voided.
If installation is not carried out in accordance with manufacturer’s instructions, this warranty may be void.
The customer must keep their “Tax Invoice” as proof of purchase of this
product and compliance certificate as proof of required installation.
Model number: ______________________________________
Serial number: _______________________________________
Date of manufacture: _________________________________
Date installed: _______________________________________
Compliance Certificate No: ____________________________
Warranty
Don’t risk your appliance warranty
Only a licensed person will give you a Compliance Certificate,
showing that the work complies with all the relevant standards.
And only a licensed person will have insurance protecting their
workmanship for 6 years.
So make sure you use a licensed person to install this appliance
and ask for your Compliance Certificate to ensure the manufacturers appliance warranty will be honoured.
Distributor
This appliance is designed, manufactured and distributed by:
Tel: 1300 727 421
4
Please read this manual before installing and using the heater.
What to do if you smell gas
1. Turn OFF the main gas supply.
2. Extinguish any open flame.
3. Open windows.
4. Do not touch electrical switches.
5. Do not use your telephone.
6. Call your gas supplier immediately from a neighbour’s phone.
Warnings
1. Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to other sections of this
manual for correct procedures, or consult with place of purchase, a
licensed plumber, a gas supplier or the CANNON distributor listed
in this manual.
2. Do not build the heater into bookcases or walls. Install only on locations as referred to on these installation instructions.
3. Due to high temperatures the room heater should be located out of
traffic and away from:
• Furniture and draperies.
• Combustible materials.
• Gasoline and other flammable liquids.
Do not place clothing or other flammable material on or near the
heater.
4. Keep curtains*, clothing, furniture and other flammable materials at
least 900mm from front and sides of the heater.
* At the owner’s discretion curtain clearance can be less than 900mm
as long as they are restrained from the front, top and sides of the
heater. The manufacturer takes no responsibility if curtain clearance is
less than 900mm and not restrained.
5. Children and adults should be alerted to the hazard of high surface
temperature and should take care to avoid burns or clothing ignition.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
6. Never attempt to burn paper or any other material in the heater.
7. Do not place articles on or against this appliance.
Do not use or store flammable materials near this appliance.
Do not spray aerosols in the vicinity of this appliance while it
is in operation.
Safety warnings
8. Sparks, ignites on low flame • Check that the wall socket to the appliance has
9. No gas to burner. • The gas valve should open at the same time as the
10. Appliance lights but goes • Test the flame for correct ionisation signal. Connect a
11. Fuse blowing. • If the fuse continues to blow check the solenoid coils
37
5
Do not modify this appliance.
8. If removed, the glass window must be put back onto the unit prior to
operating the heater.
9. Installation and repairs should be performed by a licensed service
person only, refer to back of brochure for service number.
10. For installation into a non-combustible fireplace, i.e.: masonry or brick
or into a mock fireplace, i.e. timber or plasterboard, the chimney and
base should be of sound construction and be free from cracks and
holes (to ensure that sufficient flue draught can be generated).
Note: when installing into a mock fireplace a mock fireplace
installation kit must be used.
11. The heater must be properly installed in a working chimney or connected to a venting system. Operation of this heater, when not connected into a working chimney or a properly installed and maintained
venting system can result in carbon monoxide (CO) poisoning and
possible death.
12. Testing the effectiveness of the flue.
Before testing the flue confirm air vents are unobstructed. If an exhaust
fan or other heating appliances are present switch them on. This is to
test that there is no interaction between the Cannon heater and other
appliances.
Refer AS5601.
For ‘air movement not to affect appliance’ see clause 5.3.1.
For ‘air supply to appliance’ see clause 5.4.1.
For ‘ventilation requirements’ see clause 5.4.3.
13. The appliance should be inspected prior to use, with regular inspections (annually) to be made by a licensed service person. It is important that circulating air passageways of the appliance be kept clean,
dirt and lint free, for a safe and efficient operation of the heater.
14. On first lighting your heater a smell may occur due to its new condition. This is quite normal and will disappear after a few hours use at
the maximum control position.
Important:
When this heater is operating the mesh guard/glass front is hot.
The mesh guard, or glass front, fitted to the heater conforms to
Australian Standards requirements.
The guard is fitted to this appliance to reduce the risk of fire or
injury from burns and no part of it should be permanently removed.
For protection of young children or the infirm, a secondary guard
is required.
Standards
This appliance meets the following standards:
Standards Australia: AS/NZS 3100
AS 5601
AS 4553:2008
6
Operating instructions
1. Plug the power cord into the wall socket and turn on the power to the
heater, see figure 1. Refrain from using an extension cord.
2. For control layout refer to figure 2
3. To turn heater on press switch to POWER ON position. There is a 5
second delay before the burner ignites. At this setting the burner is on
LOW and the fan speed is on LOW. Refer figure 3.
The burner will ignite on both HIGH and LOW settings.
4. To turn burner to HIGH setting, press switch for HIGH setting. Refer
figure 4.
User instructions
1
2
4
3
7
5. To increase the fan speed to MED, press switch for MED setting. Refer
figure 5.
6. To increase the fan speed to HIGH, press switch for HIGH setting.
Refer figure 6.
7. To turn the burner to LOW setting, press switch for LOW setting. Refer
figure 7.
On low burner setting it is more efficient to operate the fan speed on
LOW.
8. If the burner fails to ignite, wait 20 seconds and repeat the ignition
procedure. Refer figure 8.
To turn burner OFF To turn burner ON
9. In case of power failure return the switches to the OFF setting (refer
figure 2). When the power returns wait 20 seconds for any unburnt gas
to vent and start re-ignitions as per point 3.
5
6
7
8
8
Cleaning
All cleaning should be carried out when the heater is cold. Normally the
heater should only need wiping with a lint - free damp cloth. Any stubborn
stains can be removed with a non-abrasive spray on cleaner. If an abrasive
cleaner is used the paint finish will be damaged.
For heater fitted with the glass front:
All cleaning should be carried out when the heater is cold. Clean the outer
glass with a liquid solution ‘Windex’ or similar.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the
heater glass front since they can scratch the surface, which may result in
shattering of the glass.
Internally the heater should only be cleaned by an authorised service person listed in this manual.
If your heater requires attention contact your supplier or authorised service
person listed in this manual.
Flame characteristics
The heater flame should be stable, no lifting from the burner and the logs
should glow after approximately 15 minutes operation on HIGH setting.
The heater is a fuel effect unit and is designed to operate with luminous
flames and may exhibit slight carbon deposit on the logs. If any excess
carbon build-up on logs, or the burner flame is unstable, contact Sampford
IXL in your state. (See phone contact no page 24).
Important:
The appliance should be inspected before use and at least annually by an
authorised service person. More frequent cleaning may be required due to
excessive lint build-up from carpeting, bedding materials, pet hair, etc.
It is imperative that control compartments, burners and circulating air passage ways of the appliance be kept clean.
Do not use this fire if the glass is cracked or with the glass safety screen
removed.
Do not use fire with broken or missing logs.
Important: To
achieve the correct
visual flame effect:
On Propane the gas
pressure must be set
at 2.65 kPa with
burner operating on
maximum setting.
On Natural Gas the
gas pressure must
be set at 0.75 kPa
with burner operat-
ing pressure on
maximum setting.
Loading...