Cannon
This heater is approved for use with Natural and Propane gases.
Please leave instructions with the owner
FITZROY FREESTANDING
USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
SERVICE INSTRUCTIONS
FREESTANDING MODELS
FITZFS-SDSEB-NG
FITZFS-SDSEB-LP
2
Contents
Contents 2
❍ Distributor
Warranty 3
Safety warnings 4-5
❍ What to do if you smell gas
❍ Warnings
❍ Standards
User instructions 6-8
❍ Operating instructions
❍ Flame characteristics
❍ Cleaning
Heater specifications 9
Installation instructions 10-15
❍ Clearances
❍ Installation
❍ Gas connection
❍ Log installation
❍ Gas control
❍ Gas pressure point
❍ Installation tips
Flue installation 16-17
❍ Flue kit
Service instructions 18-20
❍ General
❍ To replace primary glass
❍ To replace outer glass
❍ To replace the gas control
❍ To replace the ignition (module) device
❍ To replace the room circulation fan
❍ To replace the fan pressure switch
❍ To remove the heat exchanger
❍ To replace the burner and spark/sense electrodes
❍ Wiring diagram
❍ Data label
❍ For service to this appliance
Trouble shooting 21-22
❍ Connections
3
The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for
residential use in Australia.
Warranty service, which includes parts and labour for the replacement or
repair of defective parts, is available through the CANNON distributor.
(Details below or on page19).
Consumers are responsible for service person’s travel outside normal service areas (approximately seventy (70k) radius from the nearest Cannon
dealer’s location), local cartage, and normal maintenance as described in
this manual.
Any product subjected to misuse, abuse, negligence, accident or alteration
will have its warranty voided. The defacement of serial plate will have its
warranty voided.
If installation is not carried out in accordance with manufacturer’s instructions, this warranty may be void.
The customer must keep their “Tax Invoice” as proof of purchase of this
product, and compliance certificate as proof of required installation.
Model number: ______________________________________
Serial number: _______________________________________
Date of manufacture: _________________________________
Date installed: _______________________________________
Compliance Certificate No: ____________________________
Warranty
Don’t risk your appliance warranty
Only a licensed person will give you a Compliance Certificate,
showing that the work complies with all the relevant standards.
And only a licensed person will have insurance protecting their
workmanship for 6 years.
So make sure you use a licensed person to install this appliance
and ask for your Compliance Certificate to ensure the manufacturers appliance warranty will be honoured.
Distributor
This appliance is designed, manufactured and distributed by:
Tel: 1300 727 421
4
Please read this manual before installing and using the heater.
What to do if you smell gas
1. Turn OFF the main gas supply.
2. Extinguish any open flame.
3. Open windows.
4. Do not touch electrical switches.
5. Do not use your telephone.
6. Call your gas supplier immediately from a neighbour’s phone.
Warnings
1. Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to other sections of this
manual for correct procedures, or consult with place of purchase, a
licensed plumber, a gas supplier or the CANNON distributor listed in
this manual.
2. Do not build the heater into bookcases or walls. Install only as referred
to in these installation instructions.
3. Due to high temperatures the room heater should be located out of
traffic and away from:
• Furniture and draperies,
• Combustible materials,
• Gasoline and other flammable liquids,
Do not place clothing or other flammable material on or near the heater.
4. Keep curtains*, clothing, furniture and other flammable materials at
least 900mm from front, rear and sides of the heater.
* At the owner’s discretion curtain clearance can be less than 900mm
as long as they are restrained from the front, top and sides of the heater.
The manufacturer takes no responsibility if curtain clearance is less than
900mm and not restrained.
5. Children and adults should be alerted to the hazard of high surface
temperature and should take care to avoid burns or clothing ignition.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
6. Never attempt to burn paper or any other material in the heater.
7. Do not place articles on or against this appliance.
Do not use or store flammable materials near this appliance.
Safety warnings
To check the operation of the electronic (module) controller (Type 537 ABC) you will require a digital
multimeter with the functions to measure AC/DC voltage, continuity, resistance and micro-amps.
It is critical that the appliance is earthed and that the active and neutrals are not reversed.
Item No Check Action
1. No ignition when appliance • Check 240 volts power to heater in incoming plug
2. Power present but appliance • If there is power to the brown wire in the 8 way
3. After resetting the module • Check the internal 2-A fuse in the loom.
4. If the fuse is O.K. and still • Check other connections are in place.
5. Confirm spark is produced • A blue spark can be seen when the heater ignition
6. If no spark being produced • Check that spark lead is connected into module.
7. Spark is being produced • Listen for cracking sound. The spark is misdirected.
8. Sparks, ignites on low flame • Check that the wall socket to the appliance has
Trouble-shooting. (Do not modify this appliance).
5
Do not spray aerosols in the vicinity of this appliance while it is in
operation.
Do not modify this appliance.
8. If removed, the glass window must be put back onto the unit prior to
operating the heater.
9. Installation and repairs should be performed by a licensed service
person only, refer to back of brochure for service number.
10. The appliance should be inspected prior to use, with regular inspections (annually) to be made by a licensed service person. It is important
that circulating air passageways of the appliance be kept clean, dirt
and lint free, for a safe and efficient operation of the heater.
11. On first lighting your heater a smell may occur due to its new condition. This is quite normal and will disappear after a few hours use at
the maximum control position.
12. Testing the effectiveness of the flue.
Before testing the flue confirm air vents are unobstructed. If an exhaust
fan or other heating appliances are present switch them on. This is to
test that there is no interaction between the CANNON heater and
other appliances.
Refer AS5601.
For ‘air movement not to affect appliance’ see clause 5.3.1.
For ‘air supply to appliance’ see clause 5.4.1.
For ‘ventilation requirements’ see clause 5.4.3.
Important:
When this heater is operating the mesh guard/glass front is hot.
The mesh guard, or glass front, fitted to the heater conforms to Austral-
ian Standards requirements.
The guard is fitted to this appliance to reduce the risk of fire or injury
from burns and no part of it should be permanently removed.
For protection of young children or the infirm, a secondary guard is
required.
This heater is not intended for use in a marine environment.
Standards
This appliance meets the following standards:
Standards Australia: AS/NZS 3100
AS 5601
AS 4553:2008
6
Operating instructions
1. Plug the power cord into the wall socket and turn on the power to the
heater, see figure 1. Use of an extension cord is not recommended.
2. For control lay-out refer to figure 2.
3. To turn heater on press switch to POWER ON position. There is a 5
second delay before the burner ignites. At this setting the burner is on
LOW and the fan speed is on LOW. Refer figure 3.
The burner will ignite on both HIGH and LOW settings.
4. To turn burner to HIGH setting, press switch for HIGH setting. Refer
figure 4.
User instructions
1
2
4
3
7
5. To increase the fan speed to MED, press switch for MED setting. Refer
figure 5.
6. To increase the fan speed to HIGH, press switch for HIGH setting.
Refer figure 6.
7. To turn the burner to LOW setting, press switch for LOW setting. Refer
figure 7.
On low burner setting it is more efficient to operate the fan speed on
LOW.
8. If the burner fails to ignite, wait 20 seconds and repeat the ignition
procedure. See below.
To turn burner OFF To turn burner ON
9. In case of a power failure return the switches to the OFF setting (refer
figure 2). When power returns, wait 20 seconds and start re-ignition
as per point 3.
5
6
7
8
Flame characteristics
The heater flames should be stable, not lifting from burner and the logs
should glow after approximately 15 minutes operation on HIGH setting.
The heater has been designed to burn with luminous flames, which mimic
natural log combustion, and may exhibit slight carbon deposition. If heavy
carbon deposits occurs or flames impinge on the roof of the combustion
chamber, turn the appliance off and contact the service agent in your state.
For service to this appliance refer page 19 for contact details.
Cleaning.
All cleaning should be carried out when the heater is cold. Normally the
heater should only need wiping with a lint - free damp cloth. Any stubborn
stains can be removed with a non-abrasive spray on cleaner. If an abrasive
cleaner is used the paint finish will be damaged.
For heater fitted with the glass front
All cleaning should be carried out when the heater is cold. Clean the outer
glass with a liquid solution such as ‘Windex’ or similar. Do not use harsh
abrasive cleaners or sharp metal scrapers to clean the heater glass front
since they can scratch the surface, which may result in shattering of the
glass.
Internally the heater should only be cleaned by a licensed service person
listed in this manual.
If your heater requires attention contact your supplier or licensed service
person listed in this manual.
Important:
The appliance should be inspected before use and at least annually by an
authorised service person. More frequent cleaning may be required due to
excessive lint build-up from carpeting, bedding materials, pet hair, etc.
It is imperative that control compartments and circulating air passage ways
of the appliance be kept clean.
Do not use this fire if the glass is cracked or with the glass safety screen
removed.
Do not use fire with broken or missing logs.
Loading...