Please read these instructions for use carefully and all other information
enclosed with the washing machine.
Keep all documentation in a safe place for future reference or for any
future owners.
Note: this machine is solely for domestic use.
Notes on disposal
All packaging material used is environmentally-friendly and recyclable. Please help dispose of
the packaging via environmentally-friendly means.
Your supplier or local council will be able to give you
details of current means of disposal.
Valuable materials can be salvaged from an old appliance via scrap reprocessing.
Introduction2
General delivery notes4
Safety notes4
Quick start5
Description of controls6
Programme Table14
Programme selector16
Detergent drawer 19
Detergents, washing aids and amounts to use20
Useful advice for the user22
The main wash23
Drying25
Automatic washing/drying cycle26
Drying cycle27
Cleaning and routine maintenance29
Investigating malfunctions31
Technical data33
Setting up + installation34
Note: pull out the mains plug from any old appliance.
Cut the power cable and dispose of it, together with the
plug.
When disposing of an old washing machine, please ensure that the door lock is rendered
inoperable to prevent children shutting themselves in the appliance.
23
BEFORE SWITCHING ON THE APPLIANCE MAKE SURE
IT IS CORRECTLY INSTALLED AND THAT THE TRANSIT
SCREWS ARE REMOVED AS SHOWN IN PAGE 34.
General delivery notes
Please check that the following items are delivered with the appliance:
- Instruction manual
- Certificate of guarantee
- Inlet hose
Check that no damage has occurred during transit, and if so, call your nearest Authorised
Technical Support Service agent.
N) If the appliance is not running properly or breaks down, switch it off, turn off the tap and do
not tamper with the appliance.
Consult only the Authorised Technical Support Service for possible repair and ask them to
use original spare parts.
Failure to comply with the above can compromise the safety of the appliance.
O) If the appliance’s power cable should ever need replacing, consult the Authorised
Technical Support Service
Quick start
Washing
Safety notes.
Note:
for cleaning or maintenance of the washing machine.
A) Pull out the plug
B) Turn off the tap
C) Candy equips all its appliances with earthing. Ensure that the mains supply is earthed,
and if it is not, seek assistance from a qualified person.
D) Do not touch the appliance when hands or feet are wet or damp. Do not use the appliance
with bare feet.
E) The use of adapters, multiple connectors and/or extensions is not recommended.
- Open the door by using the handle “A” (Fig. 1, page 6)
- Select laundry and put it in the machine
- Close the door
- Put detergent in the compartments as indicated in the programme guide in this instruction
- Select programme
- The display will show the settings for the programme selected.
- Adjust the wash temperature if necessary.
DRYING
If you would like the drying cycle to begin automatically after
washing, select the programme required using the Drying
Selection button.
Otherwise it is possible to finish the wash and then decide on the
drying programme and load.
Note:
water temperature can reach 90°C during the wash cycle.
F) Check there is no water left in the drum before opening the door.
G) This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
H) Do not pull the power cable or the appliance itself to remove the plug from the socket.
I) The appliance must not be exposed to weather conditions (rain, direct sun, etc...)
L) When moving the appliance never lift it by the controls or by the detergent drawer.
When in transit never rest the door against the trolley or transport the appliance without
the polystyrene base.
M) N.B!
If the appliance is installed on a carpeted floor ensure that the ventilation holes on the
base of the appliance are not obstructed.
4
Press additional function buttons (if required)
- Press the “Start/Pause” button
- The programme starts.
After washing
- The word “End” will appear on the display.
- Wait for the door lock to be released
- Switch off the washing machine by turning the selector
- Open the door and remove the laundry.
Ensure that the machine is correctly installed in line with the instructions found on page 34.
manual
(about 2 minutes after the programme has finished).
The “Door Security” indicator light will go out.
to “OFF” position.
5
KG Detector
Description of controls
Fig. 1
P
Door handleA
"Door Security" indicator lightB
"Start/Pause" button C
IB
D E F G H C
L
M
O
A
N
Available on the Cottons and Synthetics cycles, the intelligent sensor adjusts the water level
and programme length throughout each phase of the cycle according to how much laundry
you load into the machine. The KG Detector indicator will light up when the intelligent sensor
is weighing the laundry.
The washing machine is fitted with a self-adjusting water level system. This system
enables the machine to use the optimum amount of water needed to wash and rinse the
laundry in relation to the particular load. This results in a reduction of the water and electricity
used without in any way compromising the washing and rinsing
performance. The amount of water and electricity used will always be appropriate for the
clothes load size.
The washing machine automatically ensures excellent washing results at minimum cost whilst
respecting the environment.
Door Handle
To open the door turn the handle as shown in the picture.
A special safety device prevents the door from being opened
immediately after the end of the cycle. Wait for 2 minutes after
the wash cycle has finished and the Door Locked light has
gone out before opening the door. At the end of cycle turn the
programme selector to OFF .
The “Door Security” indicator light is illuminated when the door is fully closed and the machine is ON.
When "Start/Pause" is pressed on the machine with the door closed the indicator will flash
momentarily and then illuminate.
If the door is not closed the indicator will continue to flash.
A special safety device prevents the door from being opened immediately after the end of the cycle.
Wait for 2 minutes after the wash cycle has finished and the “Door Security” light has gone out
before opening the door. At the end of the cycle turn the programme selector to "OFF" .
7
B
“START/PAUSE” button
Press to start the selected cycle .
After selecting the programme and the required options
press the Start Pause button once to start the wash cycle.
There will be a short time delay to the start of the
programme while the machine sets the wash parameters
for the selected programme and options. The Door Locked
and KG Detector indicator lights will also illuminate a few
seconds after pressing the Start Pause button.
Changing the settings after the programmes has started (PAUSE)
Press and hold the “START/PAUSE” button for about 2 seconds, the flashing lights on the
options buttons and time remaining indicator will show that the machine has been paused,
adjust as required and press the “START/PAUSE” button again to cancel the flashing lights.
If you wish to add or remove items during washing, wait 2 minutes until the safety device
unlocks the door.
When you have carried out the manoeuvre, close the door, press "Start/Pause" button and
the appliance will continue working where it left off.
CANCELLING THE PROGRAMME
To cancel the programme, set the selector to the OFF position.
Select a different programme.
Re-set the programme selector to the OFF position.
C
“ALLERGY CARE” button
The Allergy Care option washes your clothes in a deeper than normal water level to provide
gentler washing for especially delicate fabrics, while detergent is removed
thoroughly with five extra rinses. Perfect for people with delicate skin, this option can be selected
on all Cotton and Synthetic cycles.
This option does not need to be selected on the Delicate, Woollen or Hand Wash programmes, as
it is already an integrated part of the wash cycles.
“DELAY START” button
This button allows you to pre-programme the wash cycle to delay the start of the cycle for up
to 24 hours.
To delay the start use the following procedure:
Set the required programme.
Press the button once to activate it (h00 appears on the display) and then press it again to set
a 1 hour delay (h01 appears on the display); the pre-set delay increases by 1 hour each time
the button is pressed, until h24 appears on the display, at which point pressing the button
again will reset the delay start to zero.
Confirm by pressing the “START/PAUSE” button (the light on the display starts to flash). The
countdown will begin and when it has finished the programme will start automatically.
It is possible to cancel the delay start by taking the following action:
Press and hold the button for 5 seconds until the display will show the settings for the
programme selected.
At this stage it is possible to start the programme previously selected by pressing the
“START/PAUSE” button or to cancel the process by setting the selector to the OFF position
and then selecting another programme.
E
F
The option buttons should be selected before pressing
the "Start/Pause" button.
Warning: If there is any break in the power supply while
the machine is operating, a special memory stores the
selected programme and, when the power is restored, it
“STAIN VANISH” Button
The Stain Vanish option, selectable on all Cotton cycles, tackles stubborn stains by
maintaining wash temperatures throughout the programme and adjusting the spin speed of
the drum during critical stages of the wash and rinse cycles. Using this
special programme will increase the wash efficiency without increasing the length of your
wash programme.
8
D
continues where it left off.
“TEMPERATURE SELECTION” button
When a programme is selected the relevant indicator will light up to show the recommended
wash temperature.
The Temperature button can be used to decrease or increase the temperature of your chosen
wash cycle.
Each time the button is pressed, the new temperature level is shown on the Wash
Temperature Indicator.
G
9
“DRYING SELECTION” button
With the programme selector not in the OFF position, press the button to select the required
drying programme; an indicator will light to display the drying result selected each time you
press the button.
To cancel the selection before the start of a drying programme, press the button repeatedly
until the indicators go out or return the programme selector to the OFF position.
To cancel the cycle during the drying phase, hold the button down for 2 seconds until the
cooling indicator lights up; given the high temperature inside the drum, we recommend that
you allow the dryer to complete the cool down period before returning the programme
selector to the OFF position and removing the laundry.
“SPIN SPEED” button
The spin cycle is very important to remove as much water as possible from the laundry
without damaging the fabrics. You can adjust the spin speed of the machine to suit your
needs.
By pressing this button, it is possible to reduce the maximum speed, and if you wish, the spin
cycle can be cancelled. To reactivate the spin cycle press the button until you reach the spin
speed you would like to set. To prevent damage to the fabrics, it is not possible to increase
the speed over that which is automatically suitable during the selection of the program.
It is possible to modify the spin speed without to pausing the machine.
H
I
“DIGITAL” Display
The display’s indicator system allows you to be constantly informed about the status of the machine:
1) WASH TEMPERATURE
When a programme is selected the relevant indicator will light up to show the recommended
wash temperature. The Temperature button can be used to decrease or increase the
temperature of your chosen wash cycle. Each time the button is pressed, the new
temperature level is shown on the Wash Temperature Indicator.
2) DOOR LIGHT
Once the START/PAUSE button has been pressed the light first flashes then stops flashing
and remains on until the end of the wash. 2 minutes after the end of the wash the light goes
off to show that the door can now be opened.
3) SPIN SPEED
Once the programme has been selected, the maximum spin speed allowed for that
programme appears on the display. Pressing the spin button will reduce the speed by 100
rpm each time the button is pressed. The minimum speed allowed is 400 rpm, or it is
possible to omit the spin by pressing the spin button repeatedly.
L
3
4
6
{
5
{
7
8
{
1
2
Note:
The machine is fitted with a special electronic device, which prevents
the spin cycle should the load be unbalanced. This reduces the noise
and vibration in the machine and so prolongs the life of your machine.
10
4) DELAY START LIGHT
This flashes when delay start has been set.
5) CYCLE DURATION
When a programme is selected the display automatically shows the cycle duration, which
can vary, depending on the options selected. Once the programme has started you will be
kept informed constantly of the time remaining to the end of the wash.
The appliance calculates the time to the end of the selected programme based
upon a standard loading, during the cycle, the appliance corrects the time to that
applicable to the size and composition of the load.
If is selected the automatic washing/drying, at the end of the wash phase, the drying time
remaining to the end will be shown on the display.
6) KG Detector Indicator
Available on Cotton and Synthetic cycles, during the first 4 minutes of the cycle the indicator
lights and wash time will flash. This means the intelligent sensor is weighing the laundry and
will adjust the cycle time, water and electricity consumption accordingly.
7) STAIN LEVEL
Once the programme has been selected the indicator light will automatically show the stain
level set for that programme. Selecting a different stain level the relevant indicator will light
up.
11
“STAIN LEVEL” button
3
4
2
6
{
5
{
{
1
7
8
By selecting this button (active only on COTTON and MIXED FIBRES programmes) there is
a choice of 3 levels of wash intensity, depending on how much the fabrics are soiled.
Once the programme has been selected the indicator light will automatically show the stain
level set for that programme. Selecting a different stain level the relevant indicator will light
up. For example: Using this button on the Rapid Wash cycle will enable you to select either a
14, 30 or 44 minute wash cycle.
M
8) DRYING PROGRAMME INDICATORS
The indicators display the type of the drying programme:
The washer dryers incorporate an Automatic Sensor Drying function which takes the
guesswork out of setting the drying time. You simply select the degree of dryness you
require and the dryer automatically switches off when that level is reached. For added
flexibility there are 3 Sensor Drying levels to choose from:
= Extra dry programme
= Cupboard dry programme
= Iron dry programme
USEFUL TIPS:
Once the programme option has been selected, press the Start Pause button. The appliance
will then calculate the time to the end of the selected programme based upon a full dry load.
During the cycle the appliance will update the time to suit the actual load size and dampness
of the fabrics.
T
imed programmes:
Alternatively you may select a pre-determined time for the drying cycle. The Timed Drying
programmes may be set to the following times:
120 minutes – 90 minutes – 60 minutes – 30 minutes:
Cool down phase
A 10 minute cool down phase occurs at the end of each drying cycle to ensure clothes are
not too hot to touch when the cycle finishes.
:
PROGRAMME selector with "OFF" position
When the programme selector is turned
the display lights up to show the settings
for the programme selected.
N.B. To switch the machine off, turn the
programme selector to the “OFF”
position.
Today, most detergents have been improved to wash
efficiently at lower temperatures, therefore we have set the
default temperature settings of each programme to a lower
level, saving electricity and reducing the carbon footprint of
your machine. You can select an high temperature by
pressing the temperature button.
Please refer to the programme guide for the maximum
temperature to which each programme can be set.
Press the "Start/Pause" button to start the selected cycle.
Once a programme is selected the programme selector remains stationary on the selected
programme till cycle ends.
Switch off the washing machine by turning the selector to "OFF".
Note:
The programme selector must be returned to the "OFF" position
at the end of each cycle or when starting a subsequent wash
cycle prior to the next programme being selected and started.
N
12
Buttons indicator light
These light up when the relevant buttons are pressed.
If an option is selected that is not compatible with the selected programme then the light on
the button first flashes and then goes off.
13
O
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.