346
manufacturer.
The refrigerant and insulatio n blowing gas are
fla mmable.
When disposing of th e appliance, do so only at an
auth orized waste disposal centre. Do not expose to
fla me.
7
The refrigerant isobute ne (R 6 00a) is conta ined
with in th e refrigerant circuit of th e appliance, a natu ral
gas with a high level of environmenta l compatib ility ,
which is nevertheless fla mmable. During transporta tio n
and insta llatio n of th e appliance, ensure that none of
th e components of th e refrigerant circuit becomes
damaged.
The refrigerant (R 6 00a) is fla mmable.
Caution: risk of fire
8
9
Description of the appliance
View of the appliance
1. Temperature regulator
2. Door
3. Upper drawer in freezer
4. Middle drawer in freezer
5. Ice tray
6. Lower drawer in freezer
7. Adjustable feet
8. Door handle(some models have)
1
2
3
4
5
6
7
8
Note: Due to continual modification of our products, your refrigerator may be slightly different
from this instruction Manual, but its functions and usage methods remain the same.
Control panel
Starting up and temperature regulation
Insert the plug of the connection lead into the
plug socket with a protective grounding
contact. The temperature selector knob is
located on the top of the freezer
compartment.
Thermostat Control
The thermostat control situated in the control
panel regulates the temperature of the
freezer compartment.
Positon"cold"
Positon"Mid"
Positon"Colder"
The temperature will be affected by:
Room temperature;
How often the door is opened;
How much food is stored;
Position of the appliance.
Important! Normally we advise you select a
setting of “Mid”, if you want the temperature
higher or lower please turn the knob to a
warmer or colder setting accordingly. When
you turn the knob to a colder setting, this
can lead to the more energy efficiency.
Otherwise, it would result the consumption
of energy.
Important! High ambient temperatures (e.g.
on hot summer days) and a colder setting
on the temperature regulator(position
“colder”) can cause the compressor to run
continuously or even non-stop!
Reason: When the ambient temperature is
high, the compressor must run continuously
to maintain the low temperature in the
appliance.
First use an installation
Cleaning before use
Before using the appliance for the first
time, wash the interior and all internal
accessories with lukewarm water and
meutral soap in order to remove the
typical smell of a brand new product, then
dry thoroughly.
Installation Positioning
Warning! Before installing, read the
instruction carefully for your safety
and the correct operation of appliance.
Position the appliance away from sources
of heat such as stoves, radiators, direct
sunlight, etc.
10
Maximum performance and safety are
guaranteed by maintaining the correct
indoor temperature for the class of unit
concerned, as specified on the rating plate.
This appliance performs well from N to T.
The appliance may not work properly if it is
left for a longer period at a temperature
above or below the indicated range.
Important! It is necessary to have good
ventilation around the freezer to allow for the
dissipation of heat, high efficiency an low
sufficiently cleared space should be
available around the freezer. It is advisable
for there to be 75mm separating the back of
the freezer to the wall at least 100mm of
space on its two sides, a height of over
100mm from its top and a clear space in
front to allow the doors to open 160°.
Appliances must not be exposed to rain.
Sufficient air must be allowed to circulate
in the low rear section of the appliance, as
poor air circulation can affect performance.
Built-in appliances should be positioned
away from heat sources such as heaters
and direct sunlight.
Leveling
The appliance should be level in order to
eliminate vibration. To make the appliance
level, it should be upright and both
adjusters should be in stable contact with
the floor. You can also adjust the level by
unscrewing the appropriate level
adjustment in the front (use your fingers or
a suitable spanner).
Electrical connection
Caution! Any electrical work required to
install this appliance should be carried out by
qualified or authorized personnel.
Warning! This appliance must be grounded.
The manufacturer declines any liability should
these safety measures not be observed.
Daily use
Accessories 1)
Freezer Drawer
For storing frozen food.
Ice tray
For making ice and storing ice- cubes.
Freezer food compartment 2)
For freezing fresh food and storing frozen
and deep-frozen food for long periods of
time.
Thawing food 2)
In the freezer compartment
At room temperature
In a microwave oven
In a conventional or convection oven
Food once thawed should be re-frozen
with the exception of special cases
1) If the appliance contains related accessories
and functions.
2) If the appliance contains a freezer compartment.
11
Helpful hints and tips
Noises during operation
Clicks - Whenever the compressor
switches on of off, a click can be heard.
Humming - As soon as the compressor is
in operation, you can hear it humming.
Bubbling - When refrigerant flows into thin
tubes, you can hear bubbling or splashing
noises.
Splashing - Even after the compressor has
been switched off, this noise can be heard
for a short time.
Energy saving tips
Do not install the appliance near stoves,
radiators or other sources of warmth.
Keep the time the appliance is open to a
minimum.
Do not set the temperature colder than
necessary.
Make sure the side plates and back plate
of the appliance are at some distance
from the wall, and follow the instructions
relevant to installation.
If the diagram shows the correct
combination for the drawers, crisper and
shelves, do not adjust the combination
as it would produce an effect on energy
consumption.
Hints for freezing
When first staring-up or after a period out
of use. Before putting the food in the
compartment, let the appliance run at
least 2 hours on the higher settings.
Prepare food in small portions to enable
it to rapidly and completely frozen and to
make it possible to subsequently thaw
only the quantity required.
‘Wrap up the food in aluminum foil or
polyethylene (plastic) and make sure that
the packages are airtight.
Do not allow fresh, unfrozen food to
touch food that is already frozen, thus
avoiding a rise in the temperature of
latter.
Iced products, if consumed immediately
after removal from the freezer
compartment can possibly cause skin to
become freezer burnt.
It is recommended to label and date
each frozen package in order to keep
track of the storage time.
Hints for the storage of frozen food
Make sure that commercially frozen food
was stored by the retailer.
Once defrosted, foods deteriorate rapidly
and can not be re-frozen.
Do not exceed the storage period
indicated by the food manufacturer.
Note: If the appliance contains related
accessories and functions.
Cleaning and care
Cleaning and care
For hygienic reasons, the appliance interior,
including interior accessories, should be
cleaned regularly.
The appliance should be cleaned and
maintained at least every two months.
Warning! Danger of electrical shock!
The appliance should not be connected
to the main power supply during
cleaning. Before cleaning, switch the
appliance off and remove the plug from
the main power supply, switch off, or
shut off the circuit breaker of fuse.
Notice!
Remove the food from the appliance
before cleaning. Store them in a cool
place and keep well covered.
Never clean the appliance with a steam
cleaner. Moisture could accumulate in
electrical components.
12
Hot vapors can lead to the damage of
plastic parts.
Ethereal oils and organic solvents can
attack plastic parts, e.g. lemon juice or the
juice from an orange peel, butyric acid, or
cleansers that contain acetic acid. Do not
allow such substances to come into
contact with appliance parts.
Do not use any abrasive cleansers.
Clean the appliance and the interior
accessories with a cloth and lukewarm
water. Commercially available dish
washing detergents may also be used.
After cleaning, wipe with fresh water and
a clean dish cloth.
Accumulation of dust at the condenser
increases energy consumption; clean the
condenser at the back of the appliance
once a year with a soft brush or a vacuum
cleaner.(Only for the outside-condenser
product)
Check the water drain hole on the rear
wall of the refrigerator compartment.
Clear a blocked drain hole with the aid of
something like soft green peg, an be
careful not to create any damage to the
cabinet by sharp objects.
After everything is dry, the appliance back
into service.
Defrosting
Defrosting in frozen food storage
compartment
Defrosting in the freezer chamber is
operated manually. Before defrosting,
take the foot out.
Tale the ice tray and drawers out or put
them into the fresh food compartment
temporarily.
leave the door of the refrigerator open
until ice and frost dissolve thoroughly
and accumulate at the bottom of the
freezer chamber. Wipe out the water with
soft cloth.
In order to speed up the process of
defrosting, you may put a bowl of warm
water (about 50℃) into the freezer
chamber and scrape away the ice and
frost with a defrosting spatula. After
doing so, be sure to set the knob of the
temperature regulator to the original
position.
It is not advisable to heat the freezer
chamber directly with hot water or hair
dryer while defrosting to avoid
deformation of the inner case.
It is also not advisable to scrape off ice
and frost or separate foods from the
containers which have been congealed
together with the food with sharp tools or
wooden bars, so as not to damage the
inner casing or the surface of the
evaporator.
Notice! The appliance should be defrosted
at least once a month. During its usage, if
the door has been used in extreme
humidity, we advise the user to defrost
every two weeks.
Taking the appliance out of service
Empty the appliance
Pull out the power plug
Clean thoroughly (see section: Cleaning
and Care).
Leave the door open to prevent odours
13
What to do if...
Warning! Before troubleshooting,
disconnect the power supply. Only a
qualified electrician or other
personnel must carry out the
troubleshooting that is not in the manual.
Important!
Repairs to the appliance may only be
performed by competent service engineers.
Improper repairs can give rise to significant
hazards for the user. If your appliance
needs repairing, please contact your
specialist dealer or your local Customer
Service Center.
Problem possible cause Solution
Switch on the appliance.
Plug the appliance into the
electrical socket.
Check fuse, replace if necessary.
Defective parts need to be
repaired by an electrician.
Turn the temperature regulator to
a warmer setting temporarily.
Please refer to the “Initial Start
Up” section.
Open the door only as long as
necessary.
Turn the temperature regulator to
a warmer setting temporarily.
Please refer to the “Installation
Location” section.
Please look in the “Changing the
Light Bulb” section.
Carefully warm the leaking
sections of the door seal with a
hair dryer (on a cool setting). At
the same time, shape the
warmed door seal by hand so
that it sits correctly.
Readjust the feet.
Move the appliance slightly.
If necessary, carefully bend the
component out of the way.
The compressor starts after a
period of time.
Refer the “Cleaning and Care”
section.
Appliance dose not
work.
Appliance cools too
much.
The food is too warm.
Interior lighting dose
not work.
Heavy build-up of
frost, possibly also on
the door seal.
Unusual noises.
The compressor dose
not start immediately
after changing the
temperature setting.
Water on the floor or
storage shelves.
Appliance is not switched on.
Main plug is not plugged in or is
loose.
Fuse has blown or is defective.
Outlet is defective.
Temperature is set too cold.
Temperature is not properly
adjusted.
Door was open for an extented
period.
A large quantity of warm food
was placed in the appliance
within the last 24 hours.
The appliance is near a heat
source.
Light bulb is defective.
Door seal is not air-tight
(possibly after reversing the
door) .
Appliance is not level.
The appliance is touching the
wall or other objects.
A component, e.g. a pipe, on
the rear of the appliance is
touching another part of the
appliance or the wall.
This is normal, no error has
occurred.
Water drain hole is blocked.
14
Reversing the door
The side in which the door opens can be
changed from the right side (as supplied) to
the left side, if the installation site allows for
it. Tools you will need:
1. 8mm socket driver
2. Cross- sharped screwdriver
3. Putty knife or thin-blade screwdriver
Reverse the door
1. stand the freezer, remove the two screws
on the back of the top cover, then lift the
top cover and place it on a padded surface
to prevent scratching.
3.Lift the door and place it on a padded
surface to prevent scratching. Remove both
adjustable feet and remove the bottom hinge
bracket by unscrewing the bolts. Then
transfer them to another side.
Note: You need move hinge axis from hole
① to ② before transfer.
hinge axis
②
①
4.Set the door into its new place making
sure the pin enters the bushing at the lower
frame section. Replace the lid by fitting the
upper hinge core into the upper door's hole,
securing it with the 2 screws. Replace
another 2 screws to another side.
2. Remove the four screws as follow
diagram. Lift the upper hinge core ,then put it
in a safe place.
5.Put the top cover in the freezer. Tighten
the 2 screws on the back of top cover.
Warning!
When changing the side at which the door
opens, the appliance must not be connected
to the mains. Remove plug from the mains
beforehand.
15
Installing the door handle
If there is door handle separately provided in a plastic bag with your appliance, you can install it
as follows .
1. Remove the screw on the door.Keep or
install the screw covers on the side which
have hinge.
2. Match the handle hole to the door , then
fix the screw which you removed from the
door to make the handle fixed firmly on the
door.
16
Disposal of the appliance
It is prohibited to dispose of this appliance in domestic household waste.
Packaging materials
Packaging materials with the recycle symbol are recyclable. Dispose of the packaging in a
suitable waste collection container to recycle it.
Before disposal of the appliance.
1. disconnect the main plug from the main socket.
2. Cut off the main cable and discard it.
Correct Disposal of this product
This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this
product for environmental safe recycling.
Climatic Category
Classe climatica
Clase Climática
Klimaklasse
Classe climatique
Fresh Food Volume
Volume del frigorifero
Volumen del frigorífico
Inhalt Kühlteil
Volume du réfrigérateur
Energy Class
Classe energetica
Clase energética
Gefriervermögen
Classe énergétique
Noise
Rumore
Ruido
Geräusch
Niveau sonore
TYPE:RS-12DC4S1
Protection classes
Classe di protezione
Clase de protecciόn
N,ST,T
Sicherheitsklassifizierung
Classe de protection
Frozen Volume
Volume del congelatore
Volumen del congelador
- L
Inhalt Gefrierteil
Volume du congélateur
Energy Consumption
Consumo energetico
Consumo energético
A+
Energieverbrauch
Consommation énergétique
R600a (55g) Cyclopentane
40dB
220V-240V~ 50Hz 0.7A
180kWh/annum
17
Defrost Power
Potenza Di Sbrinamento
Potencia De Descongelación
I
Abtauleistung
Freezing Capacity
Capacità di congelamento
82 L
Capacidad de congelación
Gefriervermögen
Pouvoir de congélation
Temperature Rise Time
Tempo di risalita
Autonomía
Lagerzeit bei Störung
Autonomie
Lamp
- W
Cand y Hoove r Group S rl Via Co molli ,
16 208 61 Brug herio ( MB) ITALY
FREEZER
-W
10 kg/24h
24 h
4070 323
Loading...