Campomatic FC420MS User Manual

Refrigerator User’s Manual

MODEL:FC420MS

Please go through this manual be for e use.
Thank you for purchasing our products.

Attention:

● Please understand the safety instructions before use.

● Please keep this manual well after reading it for further reference.

● Notice will not be given if this manual is altered due to product improvement.

Contents:

Name of Parts and Components
Preparations before Use
How to Use the Fridge Correctly
Attention
Maintenance
Fault and Solution
Parameters and Circuit Diagram
Door Right-Left Change

Name of Parts and Components

The fridge purchased by you may be not abs ol utel y i n ac cor d with this manual.
The packing list in the fridge shall prevail.

Preparations before Use

Product Properties
Warning

1. WARNING – Keep ventilation openings, in the appliance enclosure or in the
built-in structure, clear of obstruction.

2. WARNING – Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer.

3. WARNING – Do not damage the refrigerant circuit.

4. WARNING – Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type recommended by the
manufacturer.

5. The appliance has to be unplugged after use and before carrying out user
maintenance on the appliance.

6. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.

7. Children should be supervised to ensure that they do not play with the
appliance.

8. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.

9. Please abandon the r efrigerator accordi ng to local regulators for it use flammable
blowing gas and refrigerant.

10. Disconnect the power supply before replacing the lamp.

11. Please according to local regulations regarding disposal of the appliance for its
flammable refrigerant and blowing gas. Before you scrap the appliance, please take
off the doors to prevent children trapped.

How t o p repare new fridge

●Before using new fridge, pleas e g et r id of all wrappi ng s , i ncl uding base mat,
foam cushion for the outside, the rear, the condenser and foam cushion,
gummed paper for the i nsi de of th e fridg e.

●Wipe clean the i nsi de an d outside of the fridge with war m an d humid rag (A
little detergent can be added in the warm water. Wipe clean finally with
clear water);

●Prepare a separate 2-pole socket plus grounding, which shall not be

shared with other appliances;

●Please connect the earth wire and the earth electrode of the socket shall
have a reliable earth wire.

Transportation and Placement

Transportation

●Don’t turn over, keep horizontal, extrude or vibrate the fridge. Its inclination
shall not exceed 45°when moving it.

●Please don’t hold the door or cap when moving the fridge to avoid any
deformation.

●It is allowed to put the fridge backwards (no more than 20°) to facilitate
movement in a distance by rolling the rear trundle.。

Placement

●The fridge shall be located in good ventilation, far from heat source, out of
direct solar radiation and free of damp or water, so as to avoid rust or bad
insulation.

●The space above the top of the fridge shall not less than 30cm, the
distance from both sides and the rear to the wall shall not less than 10cm,
so as to facilitate its opening, shutting and heat release.the dimensions of
refrigerator are shown in the figure below.

●The fridge shall stand on the flat and solid ground. (If not stationary, level it
by adjusting its feet)

Attention

The power core shall not bear the fri dge or other objec ts to av oid damagi ng
it.
Before electrifying the fridge, please check if its voltage accords with the

mains voltage.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

– WARNING: Keep ventilation openings, in the appliance enclosure or in the

built-in structure, clear of obstruction.

– WARNING: Do not use mechanical devices or other means to accelerate

the defrosting process, other than th ose r ecommended by the man u f actur er.

– WARNING: Do not damage the refrigerant circuit.
– WARNING: Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of the type recommended
by the manufacturer.

Do not store explosive substances such as aerosol cans with a flammable

propellant in this appliance.
This appliance is intended to be used in household and similar applications
such as

– staff kitchen areas in shops, offices and other working environments;
– farm houses and by clients in hotels, motels and other residential type

environments;

– bed and breakfast type environments;
– catering and similar non-retail applications.

How t o Use the Fridge Correctly

Cold Chamber

●The food stored in a short term or eaten in no time shall be put in the cold
chamber, where the temperature is 0-10℃ approximately. Although it can
restrict bacteria from reproduction, it is improper to store food in the cold
chamber for long.

●The cooked food shall be put in the cold chamber after it is cooled to the
room temperature.

●It is better to airproof food before refrigeration.

●Moisture on vegetables, before refreshing, must be cleared. Otherwise,

their rotting will be expedited in the box which contains moisture.
Vegetables, if wrapped, can be stored longer.

Freezer Chamber

●Usually, the temperature of the freezer chamber is below －18℃. It is best to
put the food, if stored for a long time, in this chamber.

●Quick frozen food sh all be stor ed i n thi s c hamber as q uick ly as pos si ble w hen
it is not unfrozen.

●Hot food must be cooled to the room temperature before being put into this
chamber.

●It is prohibited to put fruits, vegetables and glass container with liquid therein
into this chamber, or they will be frozen off or explode.

●Frozen food shall be classified with the same type put together, which can
prevent the door from being unnecessarily opened in a long time and, as a
result, save energy.

Freezer Drawer

Large-pieced meat shall be cut into small pieces before freezing, if
necessary, to facilitate cooki ng. If taking out the draw er, please pull out forward
and then raise it slightly upward.

If you want to put the bigger food into freezer, you will be allowed to take
out the top three drawers from th e fre ezer, and put the food on the glas s plate.
Note: After using the freezer chamber, please close the drawer and then shut

off its door.

Ice-Making Box（If the product contains ice-Making Box）

It is used to make ice block by putting cooled boiled water equal to 4/5 of the
volume in the freezer chamber for a few hours. Twist the ice box to separate
ice block from the box, but don’t bend it to avoid fracture.

Thermostat

Thermostat knobe is to be used to adjust the temperature of the fridge
chamber. In the same ambient temperature, the knobe digit the bigger, the
temperature of the fridge chamber the lower; the smaller the kno be digit, the
higher the temp er ature of the fridg e c h am ber. Digit “0” indicate the c o mpres sor
stop working.
When the compressor run overtime or there is big ice cube in cold chamber,

you chould turn the knob to the smaller digit.
When the temperature in the fridge is high and the food in the fridge is not
fresh in shorter time, you should turn the knob to the bigger digit. Normally, we
suggest you turn the knob to the digit 3.
Note: the digit on knob represent graduation, do not represent the chamber
temperature.

Attention

Please don’t detach or repair the fridge. Please replace accessories at the
maintenance office designated by th e man u fac tur er.
Please use st and ar d 3 -hole power socket ab ove 10A, which shall b e g r ound ed
well.

Please don’t use inflammable solvent near the fridge to avoid fire.
Please don’t put inflammable, explosive, volatile and/or strongly-corrosive
substances in the f ridge to avoid damage or fire. Please don’t put liquid bottle
or closed container in the fridge to avoid explosion or damage.

Please don’t let children get into or climb the fridge to avoid injuring or prevent
it from falling down to injure them.
Please don’t put weights on the top of the fridge, for they may fall down when
closing the door.

Please don’t put too much food in the fridge.
Please avoid opening the door long or frequently, which would lower the
overall efficiency and increase the running load.

When the fridge runs abnormally or is damaged, please shut off the power
supply and notify the local service center.
Please splash water onto the top and rear of the fridge, which would lower the
insulation.

Note:
This fridge is designed for household purpose, only suitable for storing food,
not for other purposes, such as blood, medicine or biological product, etc.

Maintenance

Defrost

Before defrost, please take off the power cord. Then open the freezer door,
remove the food, drawer and ice-box all things out from the freezer, waiting for
defrosting; if you want to accelerate de fr os t, put a cup of hot water (about 50℃)
in the freezer. Cleaning the water come from defrost with dry soft cloth. Do not
defrost with metal tools and electric heater, otherwise damage the fridge
possibly. If there is heavy frost, please defrost in time, otherwise weaken the
cooling. In general, you need defrost once per three month.

Cleaning

Clear the dust behind the fridge and on the ground regularly.
The inside of the fridge must be cleared up frequently to eliminate strange
smell. Please shut off the power supply before cleaning. Please use soft towel
and neutral detergent and finally wipe clean with clear water.

Please don’t use the following substances to clean the inside of the
fridge:

●Alkaline or alkalescent detergent (which may crack the liner and plastic
parts);

●Soap powder, bensoline, banana water, etc. (which may damage the plastic

parts);

●Please wipe away the edible oil or spice timely, if attached to the fridge.
(which may crack the plastic parts)

Lamp and replacement

The lamp is 220V/2W(AC) and replaced after shutting off the power supply.
Please detach the lampshade first, detach the 3 bolts and then replace LED
lamp (detach 3 bolts). Please see the diagram.
Please use the standard accessory.
(The diagram only serves for indication. The real product shall prevail.)

Shutdown
Out of service for long : Pl ease s hut of f the po w er suppl y, for the aged wir e may

cause electric shock o fire; keep the door open for some time
and close it after the inside of the fridge is dry completely.

Power failure: Please reduce the frequency of door opening as much as

possible; fresh food is not sui t ably put in again.

Abandonment: If the fridge is abandoned, please detach the door therefrom to

prevent child from getting in.

Fault and Solution

Before maintenance, please go through the following table.

Fault Cause

Fridge not working ● See if power is through and if plug i s inserted fast.

● See if the voltage is too low.

Bad refrigeration ● See if temperature is ov er -high as adjusted

● See if too much food is put in.

● See if too hot food is put in.

● See if the door is opened and closed too frequently.

● See if there is any heat source near the fridge

Loud noise ● See if the ground is flat and if the fridge is placed steadily.

● See if the accessories to the fridge are loc ated in place.

Food in cold

chamber frozen

Peculiar smell ● The food with smel l shall be sealed closely.

● See if the cold-storage t em per at ure is in the quick-cold mode.

● See if the food containing too much water is put on the inner side

of the rack

● See if there is any food going ba d.

● The inside of the fridge needs cleaning.

If the fridge can’t work soundly still after checkup as abovementioned, please
contact our post-sale service office.
If the soft cord of power supply is damaged, the replacement must be done by
our personnel in order to avoid any danger.

Non-fault problems
The liquid refrigerant in the capillaries of the fridge flows very fast and
sometimes contain a few bubbles, which, as a result, may produce irregular
murmurs at their exit.

When the fridge is working, its rear serves to radiate heat.

In the event of large humidity in the air, the area around the door may be wet.
Just wipe with cloth.

Energy Saving Tips

· The applianc e sho u ld be loc ate d in t he coo les t area of the r oom , aw ay from
heat producing appliances or heating ducts, and out of the direct sunlight.

· Let hot foods cool to room temperature before placing in the appliance.
Overloading the appliance forces the compressor to run longer. Foods that
freeze too slowly may lose quality, or spoil.

· Be sure to wrap foods properly, and wipe cont ainers dry befor e placi ng them
in the appliance. T his cuts down on frost build-up inside the appliance.

· Appliance storage bin should not be lined with aluminum foil, wax paper, or
paper toweli ng. Liners interfere with cold air ci rcul ation, maki ng the applianc e
less efficient.

· Organize and label food to reduce door openings and extended searches.
Remove as many items as needed at one time, and close the door as soon as
possible.

Door Right-Left Change

Remove the door

1. Remove hinged cover on the top and detach top hinge

2. Detach the door of the cold chamber

(Detach)
Top hinge cover

upward

3. Remove the fixing middle-hing e bolts and detach the middl e hing e

Middle hinge

Middle-hinge bolt

4. Remove the door of the freezer chamber upward

Remove the door of the

freezer chamber upward

5. Remove the fixing lower-hinge bolts and detach the lower hinge

Lower Hinge

6. Replace the parts
Replace the lower-hinge bolt to the symmetrical position of lower hinge,
and mount the lower-hinge module to the symmetrical position of the fridge.

Replace the door handle to the symmetri cal p os i ti on o f the door.
(Remove the bolt cover with blade and the bolts then to detach the handle)

Bolt

Door

Handle

cold chamber to the symmetrical

Bolt cover cap

Replace the self-lock and dog on the freezer door to the symmetrical
position of the door on the left side.

Self-lock and dog

Replace the relevant plastic parts to the symmetrical position of the
cold-chamber door.

Replace the self-lock and dog of the

position on the left side.

7. Mount the freezer door remodeled as above to the lower hinge.

8. Mount the middle hinge to the symmetrical position with bolts

Middle hinge

9. Mount the cold-chamber door remodeled as above to the middle hinge.

10. Mount the left hinge to the left side of the fridge.

11. Put the upper hinge cover in place.

(Mount)

Top Hinge Cover

12. The diagram where the handle is mounted to the right side

Door opened on the right

Correct Disposal of this product

Correct Disposal of this product

Door opened on the left

This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.