The design and specifications are subject to change without prior notice for
product improvement. Consult with the sales agency or manufacturer for details.
CD009IU-N3(J)
2020001B0704
20120315
Before operating this product, please read the instructions
carefully and save this manual for future use.
SOCIABLE REMARK
When using this dehumidifier in the European countries, the following information
must be followed:
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary.
It is prohibited to dispose of this appliance in domestic household waste.
For disposal, there are several possibilities:
A) The municipality has established collection systems, where electronic waste can
be disposed of at least free of charge to the user.
B) When buying a new product, the retailer will take back the old product at least
free of charge.
C) The manufacture will take back the old appliance for disposal at least free of
charge to the user.
D) As old products contain valuable resources, they can be sold to scrap metal
dealers.
Wild disposal of waste in forests and landscapes endangers your health when
hazardous substances leak into the ground-water and find their way into the food
chain.
To prevent injury to the user or other people and property damage, the following instructions must be
followed. Incorrect operation due to ignoring of instructions may cause harm or damage.
The seriousness is classified by the following indications.
WARNING
CAUTION
Meanings of symbols used in this manual are as shown below.
Do not exceed the rating
of the power outlet or
connection device.
Otherwise, it may cause electric
shock or fire due to excess heat
generation.
Do not modify power cord
length or share the outlet
with other appliances
It may cause electric shock or
fire due to heat generation.
!!
Disconnect the power if
strange sounds, smell, or
smoke comes from it.
It may cause fire and electric
shock.
Do not use the machine near
flammable gas or combustibles, such
as gasoline, benzene, thinner, etc.
It may cause an explosion or fire.
Do not use the unit in small
spaces.
Lack of ventilation can cause
overheating and fire.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to property.
Never do this.
Always do this.
WARNING
Do not operate or stop the
unit by switching on or off
the power.
It may cause electric shock or fire
due to heat generation.
Do not insert or pull out
plug with wet hands.
It may cause electric shock.
You should never try to take
apart or repair the unit by
yourself.
It may cause failure of machine
or electric shock.
Do not drink or use the
water drained from the unit.
It contains contaminants and
could make you sick.
Do not damage or use an
unspecified power cord.
It may cause electric shock or fire.
Do not place the unit near
a heat source.
Plastic parts may melt and cause
a fire.
!!
Before cleaning, turn off
the power and unplug the
unit.
It may cause electrical shock or
injury.
Do not take the water bucĀket out during operation.
It may cause bucket full protect of
the unit and cause electric shock.
CAUTION
!!
Do not put in places where
water may splash onto the
unit.
Water may enter the unit and
degrade the insulation. It may
cause an electric shock or fire.
Place the unit on a
level, sturdy section
of the floor.
If the unit falls over, it may
cause water to spill and
damage belongings, or
cause electrical shock or
fire.
Do not cover the intake or
exhaust openings with
cloths or towels.
A lack of air flow can lead
to overheating and fire.
Never insert your finger or
other foreign objects into grills
or openings. Take special care
to warn children of these
dangers.
It may cause electric shock
or failure of appliance.
!!
Always insert the filters
securely. Clean filter
once every two weeks.
Operation without filters
may cause failure.
Do not, under any
circumstances, cut,
remove, or bypass
the grounding prong.
This unit is grounded through the
power cord plug when plugged
into a matching wall outlet.
Fig.1
NOTE: All the pictures in this manual
are for explanation purposes only.
Your unit may be slightly different.
The actual shape shall prevail.The
operations and functions are the
same.
SAFETY PRECAUTIONS
CAUTION
!!
Care should be taken when
using the unit in a room with
the following persons:
Infants, children, elderly people,
and people not senstive to
humidity.
Do not place heavy object on the
power cord and take care so that
the cord is not compressed.
There is danger of fire or
electric shock.
!!
If water enters the unit, turn
the unit off and disconnect the
power , contact a qualified
service technician.
It may cause failure of
appliance or accident.
Do not use in areas
where chemicals are
handled.
This will cause the unit
deterioration due to
chemicals and solvents
dissolved in the air.
Do not climb up on
or sit on the unit.
You may be injured if you
fall or if the unit falls over.
Do not place flower
vases or other water
container on top of
the unit.
Water may spill inside the
unit, causing insulation
failure and electrical
shock or fire.
Electrical Information
The manufactures nameplate is located on the rear panel of
the unit and contains electrical and other technical data
specific to this unit.
Be sure the unit is properly grounded. To minimize shock and
fire hazards, proper grounding is important. The power cord is
equipped with a three-prong grounding plug for protection
against shock hazards.
Your unit must be used in a properly grounded wal receptacle.
If the wall receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or circuit breaker,
have a qualified electrician install the proper receptacle.
Ensure the receptacle is accessible after the unit installation.
Do not use extension cords or an adapter plugs with this
unit. However, if it is necessary to use an extension cord, use
an approved dehumidifier extension cord only (available
at most local hardware stores).
To avoid the possibility of personal injury, always disconnect
the power supply to the unit, before installing and/or servicing.
22
33
CONTROL PADS ON THE DEHUMIDIFIER
The control panel of the dehumidifier you
purchased may be look like one of the following:
MODEL A
Indicator lights(MODEL A and MODEL B)
11
44
22
MODEL B
22
11
55
77
88
66
33
Fig.2
Power on indicator light(green)
11
This indicator light remains on(green)
when the unit is switched on and turns
dark when the unit is switched off.
Water full indicator light(red)
22
Glows when the bucket is ready to be
emptied, or when the bucket is removed
or not replaced in the proper position.
Continuous operation on indicator light
33
(green)-only for MODEL B
This indicator light illuminates when the
continuous operation is on.
Control pads(MODEL A)
44
POWER Pad
Press to turn the unit on and off. When
press this pad, the dehumidifier will
operate continuously for maximum
dehumidification until the bucket is full.
Control pads(MODEL B)
55
POWER Pad
Press to turn the dehumidifier on and off. It
illuminates(green) when the unit is switched on
and turns dark when the unit is switched off.
When Humidity/Temperature sensor malfunction
occurs, it blinks at 5 times per seconds.
Continue Pad
66
Select for the dehumidifier to operate continuously
for maximum dehumidification until the bucket is
full. The Humdity set control pads cannot be used
when Continuous operation is on.Press this pad
again to cancel Continuous operation.
Humidity Set Control Pads
77
The humidity level can be set within a range of
35%RH(Relative Humidity) to 80%RH(Relative
Humidity) in 5% increments.
For drier air, press the pad and set to a lower
percent value(%).
For damper air, press the pad and set a
higher percent value(%).
IDENTIFICATION OF PARTS
Display
88
Shows the set % humidity level while setting, then shows the actual(5% accuracy) room % humidity level.
Error Codes:
E1- Humidity sensor error--Unplug the unit and plug it back in. If error repeats, call for service.
E2- Temperature sensor error-- Unplug the unit and plug it back in. If error repeats, call for service.
Protection Codes:
P1- Unit is defrosting-- Allow the unit time to automatically defrost. The error will clear after the unit self defrosts.
P2- Bucket is full or bucket is not in the right position-- Empty the bucket and replace in the right position.
NOTE: When more than one codes occur, the priority of the code display order is:
P2--E2--E1--P1.
NOTE: For MODEL A,when the temperature sensor error occurs the power indicator light will blinks
at 5 times per second.
Other features
Bucket Full Light
Glows when the bucket is ready to be emptied, or when
the bucket is removed or not replaced in the proper position.
Auto Shut Off
The water level control switch shuts off the dehumidifier when
the bucket is full, or when the bucket is removed or not replaced
in the proper position. When the setting humidity is reached, the
unit will be shut off automatically.
Auto Defrost
When frost builds up on the evaporator coils, the compressor will
cycle off and the fan will continue to run until the frost disappears.
Auto-Restart(on some models)
If the unit breaks off unexpectedly due to the
power cut, it will restart with the previous function
setting automatically when the power resumes.
Wait 3 minutes before resuming operation
After the unit has stopped, it can not be restarted
opertation in the first 3 minutes. This is to protect the
unit. Operation will automatically start after 3 minutes.
Identification of parts
Air outlet grille
Water bucket
Water level
window
Handel
MODEL IMODEL II
Control panel
Air filter
Drain hose outlet
(see page 7)
Power Cord
and plug
Air outlet grille
Water bucket
Water level
window
Fig.3
Handel
Control panel
Air filter
Drain hose outlet
(see page 7)
Power Cord
and plug
44
55
OPERATING THE UNIT
Positioning the unit
A dehumidifier operating in a basement will have little or no effect in drying an adjacent enclosed storage area, such as a
closet, unless there is adequate circulation of air in and out of the area.
Do not use outdoors.
This dehumidifer is intended for indoor residential
applications only. This dehumidifier should not be used
for commercial or industrial applications.
Place the dehumidifier on a smooth, level floor strong
enough to support the unit with a full bucket of water.
Allow at least 20cm of air space on all sides of the unit
for good air circulation.
Place the unit in an area where the temperature will not
fall below 5 C(41 F). The coils can become covered with
frost at temperatures below 5 C(41 F), which may reduce
performance.
Place the unit away from the clothes dryer, heater or radiator.
Use the unit to prevent moisture damage anywhere books
or valuables are stored.
Use the dehumidifier in a basement to help prevent
moisture damage.
The dehumidifier must be operated in an enclosed
area to be most effective.
Close all doors, windows and other outside openings
to the room.
20cm or more
20cm or more
Casters(Install at four points on the bottom
of unit)
Casters can only move laterally.
Do not force casters to move over carpet,
nor move the unit with water in the bucket.
(The unit may tip over and spill water.)
NOTE:Casters is optional,some models without.
40cm or
more
Fig.4
20cm or more
20cm or more
When using the unit
When first using the dehumidifier, operate the unit continuously 24 hours.
This unit is designed to operate with a working environment between 5C(41 F) and 35 C(95 F).
If the unit has been switched off and needs to be switched on again quickly, allow approximately
three minutes for the correct operation to resume.
Do not connect the dehumidifier to a multiple socket outlet, which is also being used for other electrical appliances.
Select a suitable location, making sure you have easy access to an electrical outlet.
Plug the unit into an electrical socket-outlet with earth connection.
Make sure the Water bucket is correctly fitted otherwise the unit will not operate properly.
OOOO
Removing the collected water
There are two ways to remove collected water.
1. Use the bucket
When the bucket is full, the unit will automatically stop
running and display P2 , the Full indicator light will flash.
Slowly pull out the bucket. Grip the left and right handles
securely, and carefully pull out straight so water does
not spill. Do not put the tank on the floor because the
bottom of the bucket is uneven. Otherwise the bucket
will fall down and cause the water to spill (see Fig.5 & 6).
Throw away the water and replace the bucket. The
bucket must be in place and securely seated for the
dehumidifier to operate.
The machine will re-start when the bucket is restored
in its correct position.
NOTES:
When you remove the bucket, do not touch any parts
inside of the unit. Doing so may damage the product.
Be sure to push the bucket gently all the way into the
unit. Banging the bucket against anything or failing to
push it in securely may cause the unit not to operate.
2. Continuous draining
Water can be automatically emptied into a floor
drain by attaching the unit with a water hose
(not included).
Remove the water bucket.
Cut off the plastic cover located at drain hose
outlet by a scissor,then insert the water hose
(ID=O13.5mm) into the drain outlet (see Fig.7) and
securely press it onto the connector of the unit
(see Fig.8).
Lead the water hose to the floor drain or a suitable
drainage facility.The drainage facility should be lower
than the drain outlet of the unit.
Make sure the connection of the water hose and the
connector is tight and do not let the water leak.
Be sure to run the water hose sloping downward and let
the water flow out smoothly.Do not install the water
hose as shown Fig.9a and Fig.9b.
Replace the bucket in the unit. The bucket must be in
place and securely seated.
NOTE: When the continuous drain feature is not being
used, remove the drain hose from the outlet.
,,
,,
OPERATING THE UNIT
1. Pull out the bucket a little.
Fig.5
2. Hold both sides of the bucket
with even strength, and pull it
out from the unit.
Fig.6
3. Pour the water out.
Cut off the plastic
cover, then insert
the water hose.
Fig.7
Water hose
Connector
Fig.9a
Do not block water flow by a rise.
66
Fig.9b
Do not block water flow by a retortion.
77
Fig.8
CARE AND MAINTENANCE
Care and cleaning of the dehumidifier
Turn the dehumidifier off and remove the plug
from the wall outlet before cleaning.
1. Clean the Grille and Case
Use water and a mild detergent. Do not use bleach
or abrasives.
Do not splash water directly onto the main unit. Doing
so may cause an electrical shock, cause the insulation
to deteriorate, or cause the unit to rust.
The air intake and outlet grilles get soiled easily, so use
a vacuum attachment or brush to clean.
2. Clean the bucket
Every few weeks, clean the bucket to prevent growth
of mold, mildew and bacteria. Partially fill the bucket
with clean water and add a little mild detergent.
Swish it around in the bucket, empty and rinse.
NOTE: Do not use a dishwasher to clean the bucket.
After clean, the bucket must be in place and securely
seated for the dehumidifier to operate.
3. Clean the air filter
The air filter behind the front grille should be
checked and cleaned at least every 30 days
or more often if necessary.
NOTE: DO NOT RINSE OR PUT THE FILTER
IN AN AUTOMATIC DISHWASHER.
To remove:
Grip the tab on the filter and pull it upward, then
pull it out as shown in Fig.9a.
Clean the filter with warm, soapy water. Rinse and
let the filter dry before replacing it. Do not clean the
filter in a dishwasher.
To attach:
Insert the air filter into the unit as shown in Fig.9b.
CAUTION:
DO NOT operate the dehumidifier without a filter
because dirt and lint will clog it and reduce
performance.
Fig.9a
TROUBLESHOOTING TIPS
Before calling for service, review the chart below first yourself.
Problem
Unit does not start
Dehumidifier does not
dry the air as it should
The unit makes a loud
noise when operating
Frost appears on the
coils
Water on floor
E1, E2, P1 or P2 appear
in the display
Make sure the dehumidifier s plug is pushed completely into the
outlet.
Check the house fuse/circuit breaker box.
Dehumidifier has reached its preset level or bucket is full.
Tank is not in the proper position.
Do not allow enough time to remove the moisture.
Make sure there are no curtains, blinds or furniture blocking the
front or back of the dehumidifier.
The humidity control may not be set low enough.
Check that all doors, windows and other openings are securely
closed.
Room temperature is too low, below 5 C(41 F).
There is a kerosene heater or something giving off water vapor
in the room.
The air filter is clogged.
The unit is tilted instead of upright as it should be.
The floor surface is not level.
This is normal. The dehumidifier has Auto defrost feature.
Hose to connector or hose connection may be loose.
Intend to use the bucket to collect water, but the back
drain plug is removed.
These are error codes and protection codes. See the CONTROL
PADS ON THE DEHUMIDIFIER section.
What to check
,
4. When not using the unit for long time periods
After turning off the unit, wait one day before emptying
the tank.
Clean the main unit, bucket and air filter.
Twist the excess cord onto the unit.
Cover the unit with a plastic bag.
Store the unit upright in a dry, well-ventilated place.
88
Fig.9b
99
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.