Campomatic Chimney K User Manual

USE AND CARE GUIDE

WALL MOUNTED HOOD

Fig.1

Fig.2 Fig.3

Fig.4 Fig.5

A B

Fig.6 Fig.7

Fig.8 Fig.9

Fig.10 Fig.11

Fig.12 Fig.13

Fig.14

Fig.15 Fig.16

Fig.17 Fig.18

GENERAL

Carefully read the following important information regarding installation
safety and maintenance. Keep this information booklet accessible for further
consultations. The appliance has been designed for use in the ducting
version (air exhaust to the outside – Fig.1B), filtering version (air circulation
on the inside – Fig.1A) or with external motor (Fig.1C).

SAFETY PRECAUTION

1. Please take note that when the cooker hood is operating simultaneously

with an open fireplace or burner that depend on the air in the environment,
the cooker hood may removes the air from the environment which a burner
or fireplace need for combustion. The negative pressure in the environment
must not exceed 4Pa (4x10-5 bar). Provide adequate ventilation in the
environment for a safe operation of the cooker hood. Follow th e local laws
applicable for external air evacuation.

Before connecting the model to the elec tricity network:

- control the data plate (positioned inside the appliance) to ascertain that the
voltage and power corre spond to the network and the socket is suitable. If in
doubt please ask qualifie d electrician for help.

2. WARNING!

In certain circumstances electric al appliances may be a danger hazard.
A) Do not check the status of the filt ers while the cooker hood is operating
B) Do not touch bulbs or adjacent areas, after prolonged use of the lighting

installation.
C) Flambe cooking is prohibited underneath the cooker hood
D) Avoid fre e flame, as it is damaging the filters and can cause fire hazard
E) Constantly check food frying, the overheated oil may become a fire

hazard
F) Disconne ct the electrical plug prior to any maintenance.
G) There shall be adequate ventilation in the room when the range hood is
operating
H) There is a risk of fire if cleaning is not carried out in accordance with the

instructions
I) If the supply cord is damaged, it must be replaced by the manufacturer or

its service age nt or a sim ila r ly qual ifi ed pe rso n
J) This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concernin g use of the a ppliance by a person res ponsible for their safety.
K) Children should be supervised to ensure that they do not play with the

appliance.
L) The air must not be discharged into a flue that is used for exhausting

fumes from appliances burning gas or other fuels
M) The minimum distance between the supporting surface for the cooking

vessels on the hob and the lowest part of the range hood shall be at least

65cm. The instructions for installation of the gas hob specify a greater

distance has to be take n into account if requirement stated
O) Regulation concerning the discharge of air has to be fulfilled.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out by specialized

personnel.

IEC227

North America

L=live

Brown

Black

N=neutral

Blue

White

E=earth

Green/Yellow

Green

• Electric Connection

The appliance has been manufactured as class I, therefore earth cable is
necessary.
The connec tion to the mains is carried out as follows:

If the plug is not provided, connect the electrical load as indicated on the
description label. When a plug is provided, the cooker hood must be
installed in order that the plug is easy to access.

An omnipolar switch with a minimum aperture of 3mm between contacts; in
line with the electrical load and local standards, must be placed between the
appliance and the network in the case of direct connection to the electrical
network.

• The minimum distance between the support surfaces of the cooking pots on
the cooker top and the lowest part of the cooker hood must be at least 65 cm.
If a connection tube composed of two parts is used, the upper part must be
placed outside the lo wer part.
Do not connect the cooker hood exhaust to the same conductor used to
circulate hot air or for evacuating fumes from other appliances generated by
other than an electrical source.
Before proceeding with the assembly operations, remove the anti-grease
filter(s) (Fig.5) so that the unit is ea sie r t o ha nd le.
In the case of assembly the appliance, in the suction v ersion prepar e the hol e
for evacuati on of the a ir.

• FIXING TO THE WALL

Drill the holes A respecting to the distances indicated (Fig.2).
Fix the appliance to the wall and align it in horizontal position to the wall
units. When the appliance has been adjusted, fix the hood using the screws
A.
For the various installations use screws and screw anchors suited to the type

of wall (e.g. reinforced concrete, plasterboard, etc.). If the screws and screw
anchors are provided with the product, kindly check the screws are suitable
for the type of wall in which the hood is to be fixed.

• FIXING THE DECORATIVE TELESCOPIC FLUE

Arrange the electrical power supply within the dimensions of the d ecorati ve
flue. If your appliance is to be installed in the ducting version or in the
version with external motor, prepare the air exhaust opening. Adjust the
width of the support bracket of the upper flue (Fig.3). Then fix it to the
ceiling using the sc rews A (Fig.2) make sure that it is in line with you r hood
and respecting the distance from the ceiling indicated in Fig.2. Connect the
flange C to the air exhaust hole using a connection pipe (Fig.4).

To transform the hood from a ducting version into a filtering version, ask
your dealer for the charcoal filters and please follow the installation
instructions.

• FILTERING VERSION

Install the hood and the two flues as described in the paragraph for
installation of the hood in ducting version. To assemble the filtering flue
refers to the instructions con tained in the kit. If the kit i s not provide d, please
order it from your dealer. The charcoal filters must be fitted in the du cting
unit located ins id e th e hoo d.

USE AND MAINTENANCE

• It is recommended to operate the appliance pr ior to cooking.

It is recommended to le ave the ap pliance in operation for
15 minutes after cooking is terminated in order to completely eliminate
cooking vapors and odours.
The proper function of the cooker hood is conditioned by the regularity of
the maintenan ce oper ati o ns, in pa r tic u lar, the active carbon filter.

• The anti-grease filters capture the grease particles suspended in the air, and
are therefore subject to clogging according to the frequency of the use of the
appliance.
In order to prevent fire hazard, it is recommendable to clean the filter at a
maximum of 2 months by carrying out the following instructions:

- Remove the filters from the cooker hood and wash them in a solution of

water and neutra l li quid de te r gen t, leav i ng to soak.

- Rinse thoroughly with w arm water and leave to dry.

- The filters may also be washed in the dishwas her.
Please take note that the aluminum panels may alter in color after several
washes.

• The active carbon filters purify the air that is replaced in the environment.
The filters are not washable or reuseable and must be replaced at maximum
every four months. The saturation of the active carbon filter depends on the
frequency of use of the appliance, also by the type of cooking and the
regularity of cleaning on the anti-grease filters. (Fig 6) To remove the
charcoal filters place our hand on one filter at a time and turn it toward the
front part. The charcoal filter can now be removed. Always ensure to replace
both filters at the sam e time.

• Clean the fan and other surfaces of the cooker hood regularly using a cloth
moistened with denatured alcohol or non abrasive liquid detergent.

• The illumination installation is designed for use during cooking and not for
prolonged general illumination of the environment. Prolonged use of the
illumination installation notably reduces the durat ion of the bulb.
Use a one-edged screwdriver or any other appropriate tool to lift and remove
the overhead light fixture. Replace the damaged lamp. Use only halogen
lamps as the original specification, avoiding contact with hands. Return the
light fixture to its pos ition (snap fastening). (Fig. 7)

• How to replace the charcoal filters：
(1) Push the right middle corner on the glass of the decoration door (Fig.A),

the decoration door will open (Fig.B).

(2) Take out the a luminum filter (Fig.C);
(3) Push the clips on the charcoal filters and then pull back, then the charcoal

filters can be ta ke n dow n (Fig.D).

Fig.A Fig.B

Fig.C Fig.D

• How to replace the charcoal filters for 35 series

1. Push the middle bottom edge of the glass door (F ig.E)

2. The inside gas sp ring will help you to open the glass door , and fixed at

an angle (Fig.F)

3. Take out the aluminum filter (Fig.G)

4. Push the buckle of the charcoal filters with both hands then pull out.

The charcoal filters ca n be taken down. (Fig.H)

Fig.E Fig.F

Fig.G Fig.H

• FUNCTION KEYS: (Fig.8)

•FUNCTION KEYS: (Fig.9)

E =LIGHT

A = OFF
B = SPEED I / OFF
C = SPEED II / OFF
D = SPEED III / OFF

A= TIMER – 15 MINUTES
B= SPEED I

C= SPEED II
D= SPEED III

E = LIGHT

• If your appliance does not have the INTENSIVE speed function, press key

A for two seconds and it will be activated for 15 minutes after which it will
return to the previously set speed. If the function program of the unit is
active the LED will flash.
By pressing any key except the key for the light, the hood will return
immediately to its normal functioning.

The “automatic stop timer” mode delays stoppin g operation of the hood,
the mode will continue functioning for 15 minutes at the operatin g spe e d
set at the time this function is activated.

 FUNCTION KEYS: (Fig.10)

A == OFF
B == SPEED 1/“－”Control
C == SPEED 2/“＋”Control
D == SPEED 4

E == LIGHT
By pressing key B、C or D individually, the speed for each key will be the
same as above table. At the same time indicated lig ht will flash on the each

function key butt on. To stop the speed function press key A.
If Speed 3 is r equired，press key C adjust“＋”. At Speed 3 program both key
B and key C indication light will flash on each function ke y button.

To on the light press key E. To off the light press key E again.

 FUNCTION KEYS: (Fig.11)

A == Automatic Stop Tim er —15 minutes
B == Speed 1/“－”Control
C == Speed 2/“＋”Control
D == Speed 4

E == Light
By pressing key B、C or D individually, the speed for each key will be the
same as above table. At the same time indicated light will flash on the each

function key butt ons. To stop the speed function press key A.

If Speed 3 is r equired，press key C adjust“＋”. At Speed 3 program both key
B and key C in dication light will flash on each funct ion key button.
To on the light press key E. To off the light press key E again.
When the appliance and light are ON together or separately, press key A the
Automatic Stop Timer will start the 15 minutes count down. Indication light
on the key A button will flash for the duration. To stop the Automati c Stop
Timer Function before 15 minutes time frame, press key A again.

 FUNCTION KEYS: (Fig.12, Fig.17)

A == Infrared Remote Control
B == Off

C == Speed 1/“－”Control
D == Speed 2/“＋”Control

E == Light
By pressing key C or D individually, the speed for each key will be the same
as above table. At the same time indication light will flash on the each
function key button. To stop the spe ed function press key B.

If Speed 3 is r equired，press key D and adjust“＋”. At Speed 3 program both
key C and key D indication light will flash on each function key button.
To on the light press key E. To off the light press key E again.

 FUNCTION KEYS: (Fig.13, Fig.18)

A == Infrared Remote Control
B == Automatic Stop T im er —15minutes

C == Speed 1/“－”Control
D == Speed 2/“＋”Control

E == Light
By pressing key C or D individually, the speed for each key will be the same
as above table. At the same time indicated light will flash on the each
function key buttons. To stop the speed function press key B. If using
Remote Control just press the“OFF”button

If Speed 3 is r equired，press key D and adjust“＋”. At Speed 3 program both
key C and key D indication light will flash on each function key button. If
Speed 4 function is available, when Speed 4 function is ON key C and D
indication light will flash. If using Remote Control press the “

”key.
To on the light press key E. To off the light press key E again.
When the appliance and light are ON together or separately, press key A the
Automatic Stop Timer will start the 15 minutes count down. Indication light
on the key A button will flash for the duration. To stop the Automatic Stop

Timer Function before 15 minutes time frame, press key A again.

• FUNCTION KEYS :( Fig.14)
A= Filterin g system / Set clock

B= Delay Timer
C= Speed S1/ “-” adjust / off
D= Digital d isplay
E= Speed S1/ “+” adjust / off
F= Alarm
G= Light

When the Key A is flashing, at the same time “

”is flashing on the
digital display, it reminds the user to clean the filters. After the filter has
been cleaned assemble back. Press key A till the light is off and the unit is
back to setting function again.

When pressing key A for 3 seconds, the clock “

”on the digital
display will flash, press key A to switch the mode function to set hours
and minutes, and then press key C or E to set the correct time. The
Clock’s system is 24 hours.

When the motor is on, press key B the light will on. At the same time

“

” will flash on the digital display，and to press key B to
switch the function mode to set hours and minutes. To set the time to
automatically shut off, key C or E has to be pressed. Press key B for 3
seconds to s top the delay timer.

Press key C or E, to start the first speed, and it shows “

display，and to press key C once again to turn off. To run the 2

” o n the di gi tal

nd

, 3rd
and “Turbo” speed, press Key E. I f the “Turbo”speed is on, press key
E once again to turn off; and by pressing key C the speed can be
adjusted down from 3

rd

, 2nd and 1st.

Press key F light will flash, and it shows“

” flashing on the
digital display，to press ke y F again to switch to set hours and minutes
mode. To set the alarm press key C or E. To stop the alarm, press the key

F. And to cancel the alarm set, press the key F for 3 seconds.

Press key G light will on, and symbol “

” display on the digital screen,

and press key G again to turn off the light.

•FUNCTION KEYS: (Fig.15)
A= Timer (a utomatic shut off)

B= Speed 1 / a djust / switch off
C= digital display screen (showi ng timer and speed)
D= Speed 3 / adjust / switch off
E= Light
When key A is bein g pre sse d, digital display screen will show "15 minutes"
for timer whereas the m inutes can be adjusted by pressing "+" or "-" on key
B and D. When the first speed is on, pressing key A once to switch off, the
digital display will shows "00" on the screen
When key B is bei ng pre sse d, it shows "F1" on the digital display screen at
the same time first sp eed is on. By pressing key B again to switch off,
the digital di sp lay will show "00" on the sc ree n.
When key D is bein g pre sse d, it shows "F3" on the digital display screen at
the same time the third speed is on. By pressing key D again to sw i tch of f,
the digital disp lay will show "00" on the screen.
The second speed F2 and Turbo speed F4 can be adjusted by press in g key B
or D. When key E is being pressed, the light will on, by pressing key E again
is to switch off the lig ht.
If the motor and light are operating together or only the motor is working,
pressing key A, automatic switch off timer mode will get on. In other word
the unit will delay 15 minutes to turn off the motor and the light. To press
key B or key D is to adjust the time, whereas to press key A again is to stop
the timer.

 FUNCTION KEYS: (Fig.16, Fig.18)

A == Infrared Remote Control
B == Timer (Automatic Shut Off)

C == Digital Display（Timer/Speed)
D == Speed F1/Cycle Control Adjustment/Off
E == Light
When key B is pressed, digital display screen will display 15 minutes. For
cycle control adjustment and Speed F1 press key D. To stop the operation
press key B again the digital display screen will show 00. If using remote
control pre ss “OFF” button.
When key D is being pressed, the digital display screen will show F1 and
speed 1 will ON. To stop F1 function press key D until the digital display
screen shown 00.
The F2, F3 Or F4 (Turbo) function can be adjusted thru key D.
For ON/OFF l ight press key E.
When the appliance and light are ON together or separately, press key B the
Automatic Stop Timer will start the 15 minutes count down. Key D can also

be used to extend the time of Automatic Stop Timer. To stop the Automatic

Problem

Possible re ason

Solution

Hood doesn’ t work

Electric supply

Check whether the plug is conne ct ed

Check whether the main switch is
turned on

Poor airflow
Aluminum grease filters
clogged

Clean the filters, assembly back
when dry

Charcoal fi lters clogged

Replace the charcoal filters

Motor running
without air flow

Butterfly valve jammed

Contact techn ic ia n

After running for a

High temperature safety
device activated

The kitchen is not sufficiently
ventilated

The hood is being

cooking stove

The hood must be least 65cm of
Strong cooking
smell

Charcoal filters do not
install

In re-circulating mode, charcoal
filters must be installed

Oil dripping onto

Oil cup missing or not
installed

Replace aluminum filter and replace
oil cup

Aluminum grease filter
saturated

Wash the aluminum grease filters
Whirring sou nd

Fan blade problem

Contact with tec h nic ia n

Stop Timer Function before 15 minutes t ime frame, press key B again.

Troubleshooting

while, motor stop
working

installed too near to the

distance from the stove

stove

THE MANUFACTURORY DECLINES ALL RESPONSIBILITY FOR
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE
WARNINGS.

Correct Disposal of this product
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material

resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.

Warranty In formation

The manufacturer provides warranty in accordance with the legislation
of the customer's own country of residence, with a minimum of 1 year
(Germany: 2 years), starting from the date on which the appliance is
sold to the end user.

The warranty only covers defects in material or workmanship.

The repairs under warranty may only be carried out by an authorized
service centre. When making a claim under the warranty, the original
bill of purchase (with purchase date) must be submitted.

The warranty will not apply in case s of:

- Normal wear and t ear

- Incorrect use, e.g. overloading of the appliance, use of non-approved
accessories

- Use of force, damage caused by exter nal influences

- Damage caused by non-observance of the user manual, e.g. connection
to an unsuitable mains supply or non-compliance with the installation
instructions

- Partially or completely dismantled appliances