Camos Selfsat H10D User manual
Before using this product please read this manual carefully and follow exactly
all installation, mounting & orientation instructions.
All the instructions should be followed in order to avoid any technical problems.
Any electric or magnetic field close to the SELFSAT-H10D may cause a bad reception
or even cut off the signal completely.
Do not drill the plastic cover of the antenna, which seals the antenna from moisture.
Handle the antenna with care as any impact will cause damage to the electronics.
Do not open the cover, any attempt to repair by a non-qualified person can be
dangerous and void the warranty.
Any obstacle (buildings, trees, etc....) will block the reception of the signal from
the satellite to the antenna.
Do not paint or add any substance on the antenna cover, this will block the reception of
the signal from the satellite.
The cable between the antenna and the Satellite receiver should not exceed 30m as it
will decrease the quality of the signal.
The use of non- isolated jacks will result in a loss of the signal level.
For an optimum signal reception please use the Attenuation Thin Pad for the first
installation.(for more details, please refer to step 6)
Do not forget to adjust the antenna and the bracket to the cross-polarity (skew angle
please refer to step 5).
SELFSAT-H10D
What is SELFSAT-H10D?
Safety Instructions
SELFSAT-H10D is a Horn Array Type Satellite Antenna with Dual Linear Polarization,
it can receive signal from major Satellites and would replace a normal former Parabolic
Dish. Small, discreet and easy to use, it can be installed in a few minutes and used as a
portable antenna for all satellite receptions. SELFSAT-H10D can be used for both free to
Air and encrypted (requiring a subscription with an operator) channel reception; it can also
receive all High Definition channels with a superior image quality. For the use and
installation, please read the following instructions and installation materials carefully.
Tighten all the screws of the antenna once you have finished the adjustments.
This product contains one universal LNB, it is forbidden to add, change or modify the LNB.
For more precise details on the above points or for any information, please ask your
retailer or customer service.
Warning!!!
Antennas improperly installed or installed to an inadequate structure are very
susceptible to wind damage. This damage can be very serious or even life
threatening. The owner and installer assumes full responsibility that the installation is
structurally sound to support all loads (weight, wind & ice) and properly sealed against
leaks. The manufacturer will not accept liability for any damage caused by a satellite
system due to many unknown variable applications.
SELFSAT-H10D
Box Content
No
1
1
1
1
1
1
1
A1
Antenna
Body
Attenuation
PAD
Skew
Bracket
Angle
Bracket
Main
Support
Window
Bracket B
P1
B1
B2
B3
B5
2
3
4
5
7
1
Window
Bracket A
B4
6
Symbol Part name Image Quantity
No
1
Fix Bracket
A
B6
8
1
Fix Bracket
B
B7
9
1
Spanner
B8
10
1
Compass
C1
11
2
S1
12
2
S2
13
1
S3
14
1
Hex Bolt
M6x45 SEMS2
Round Head
Square
Neck Bolt M6x30
S4
15
1
Screw
M4x10 SEMS2
Hex Bolt
M6x12 SEMS2
Hex Bolt
M6x20 SEMS2
S5
16
4
Round Head
Square
Neck Bolt M6x50
S6
17
4
Round Head
Square
Neck Bolt M6x75
S7
18
8
Flanged Nut
M6
N1
19
4
Rubber
E1
20
Symbol Part name Image Quantity
Depending on the choice of installation position for the SELFSAT-H10D, you can then
decide on the mounting type, all parts are included .
By following the instructions step by step you can proceed easily to install
SELFSAT-H10D by yourself or with the help of a professional antenna installer.
How to Install?
Step 1: Where to Install?
Before installing your antenna, you check that SELFSAT-H10D box contains all the items
listed above in the ‘Box Content’ . In the event of any missing parts, please contact your
distributor.
In order to receive a signal from the Satellite, SELFSAT-H10D is to be installed in an open
loop space (outside the house or the apartment), in the direction of the satellite towards the
equator, for which, you will need a compass to exactly orient SELFSAT-H10D toward the
satellite (Note; please take reference to the table of the Azimuth angles specified in the
back pages of this manual)
Step 2: Installation Choice
A) T able Stand type (On a Horizontal Plain)
Make sure that there are no obstacles in front of SELFSATH10D which can decrease the signal reception quality, such
as buildings, or trees (you may keep in mind that trees will
grow and may block the signal).
In order to be able to fix and install your antenna easily you
might choose an easily accessible place without any potential danger for installation.
Think about the way you might pass your cable in a discreet way from the SELFSAT-
H10D to your Set top Box. The antenna should not be too distant from your satellite
receiver; a cable longer than 30 meters can decrease the quality of the signal.
Note; To ensure an accurate compass reading,
stay away from large metal objects, specifically
electrical cables and then make multiple readings
Loading...