CAME SALOON40 Installation Manual

SWING-LEAF

TURNSTILE

FA00068-EN

English

N

INSTALLATION MANUAL

SALOON40

p.

2

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

WARNING!

important safety instructions for people:

READ CAREFULLY!

Premise

• Employ this product only for the use for which it was expressly made.
Any other use is dangerous. CAME S.p.A is not liable for any damage
caused by improper, wrongful and unreasonable use • The safety of
this product and its proper fi tting depends, therefore, on respecting its
technical characteristics and proper fi tting, to be done in state-of-the-art
fashion, and under safe conditions as expressly explained in the literature
that comes with the product. • Keep these warnings together with the
installation and operation manuals that come with the operator.

Before installing

(checking what's there: if something is missing, do not continue until you
have complied with all safety provisions)

• Fitting and testing must be be only performed by qualifi ed technicians.
Laying the cables, installation and testing mus follow state-of-the-art pro­cedures as dictated by regulations • Before beginning any operation it
is mandatory to carefully read all instruction; improper installation may
result in serious harm to people and things. • Make sure the operator is
in good mechanical state, balanced and aligned, and that it opens and
closes properly. Also, if needed, fi t suitable protections o use proper safety
sensors • If the operator is to be installed at a height of over 2.5 m from
the ground or other access level, make sure you have any necessary pro­tections and/or warnings in place • Make sure that the opening turnstile
or gate cannot entrap people • Do not install the operator upside down
or onto elements that could yield and bend. If necessary, add suitable
reinforcements to the anchoring points • Do not install the operator on
tilted surfaces • Make sure any sprinkler systems cannot wet the operator
from the ground up.

Installing

• Suitably section o and demarcate the entire installation site to prevent
unauthorized persons from entering the area, especially minors and chil­dren • Be careful when handling operators that weigh over 20 kg. If need
be, use proper safety hoisting equipment • The CE-marked safety devices
(photocells, stepping plates, sensitive safety-edges, emergency buttons,
and so on), must be fi tted in compliance with the regulations in e ect and
according to state-of-the-art criteria, taking into account the environment,
the type of required service and of the working forces applied to moving
leaves. Any shearing or conveying points must be sensor-protected • Any
residual risks must be pointed out to end users and highlighted with pic­tograms as provided by the law. • All opening commands (that is, buttons,
key switches, magnetic readers, and so on) must be installed at least 1.85
m from the perimeter of the gate's working area, or where they cannot
be reached from outside the gate. Also, any direct commands (buttons,
touch panels, and so on) must be installed at least 1.5 m from the ground
and must not be reachable by unauthorized persons • The turnstile must
visibly show its identifi cation data. • Before connecting the main power
supply make sure that the identifi cation data correspond to the those of
the network • The turnstile must be connected to an e ective regulation
grounding system.

• The manufacturer declines any liability for using non-original products;
which would result in warranty loss • All maintained action commands,
must be fi tted in places from which the moving gate leaves and transit and
driving areas are visible • Apply, if missing, a permanent sign showing the
position of the release device • Before delivering to the users, make sure
the system is EN 12453 and EN 12445 standard compliant (regarding
impact forces), and also make sure the system has been properly adjusted
and that any safety, protection and manual release devices are working
properly • Apply Warning Signs where necessary and in a visible place.

Special user-instructions and recommendations

• Keep turnstile operation areas clean and free of any obstructions. Make
sure the photocell's operating fi eld is clear of any obstructions • do not
allow children to play with fi xed commands, or to loiter in the turnstile's
maneuvering area. Keep any remote control transmitters or any other
command device away from children, to prevent the operator from being
accidentally activated • The apparatus may be used by children of eight
years and above and by physically, mentally and perceptively challenged
people, or even ones without any experience, provided this happens un­der close supervision or once they have been properly instructed to use
the apparatus safely and to the potential hazards involved. Cleaning and
maintenance by users must not be done by children, unless properly su-

pervised • Frequently check the system for any malfunctions or signs
of wear and tear or damage to the moving structures, to the component
parts, all anchoring points, including cables and any accessible connec­tions. Keep any hinges, moving joints and friction points properly lubri­cated • Perform functional checks on the photocells and sensitive safety
edges, every six months. Constantly clean the photocells' glass covers
using a slightly water-moistened cloth; do not use solvents or chemicals
that could damage the devices • If repairs or modifi cations are required
to the system, cut o the main power supply and do not use it until safety
conditions have been restored • Cut o the power supply before per­forming any manual openings • If the power supply cable is damaged, it
must be replaced by the manufacturer or authorized technical assistance
service, or in any case, by similarly qualifi ed persons, to prevent any risk •
It is FORBIDDEN for users to perform any OPERATIONS THAT ARE NOT EX­PRESSLY REQUIRED OF THEM AND WHICH ARE NOT LISTED in the manu­als. For any repairs, modifi cations and adjustments and for extra-ordinary
maintenance, CALL TECHNICAL ASSISTANCE • Log the job and checks
into the periodic maintenance log.

Further recommendations for all

• Keep away from hinges and mechanical moving parts • Do not enter
the operator's area of operation when it is moving • Do not counter the
operator's movement as this could result in dangerous situations • Always
pay special attention to any dangerous points, which have to be labeled
with specifi c pictograms and/or black and yellow stripes • When using
a selector switch or a command in maintained actions, keep checking
that there are no persons within the operating range of any moving parts,
until the command is released • The gate may move at any time and
without warning • Always cut o the power supply before performing any
maintenance or cleaning.

Danger of hand crushing

Danger! High voltage.

Emergency button

p.

3

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Legend

Technical data

Description

Intended use

Limits to use

Packing list

The motor-powered turnstile is designed for controlling pedestrian transit in high-volume passage zones such as
in shopping malls, supermarkets, fitness centers and all of those areas where the transmit of people needs to be
controlled.

 Any installation and/or use other than that specified in this manual is forbidden.

The maximum width of the leaf is 1,200 mm and its weight is 1.5 Kg.

This product is made by Came S.p.A. in conformity with current safety laws. Bidirectional motor-powered swing-leaf
turnstile, with removable aluminum body and upper cover with anodized scotch-brite finishing for a STAINLESS STEEL
look.
The leaf structure is made of aluminum and the panel is made of plexiglass.
The leaf opening, in either direction, can be activated by a card reader, photocells, or other control device. The opening
speed of the 90° leaf is preset. The leaf opening can be automatic (it closes after a preset time) or activated by control
device if the bidirectional opening is not set.

The operator IS reversible even when the operator is powered up. If the closed leaf is forced, it then repositions closed.
The complete range:
001PSSLN40 - Single bidirectional motor-powered swing-leaf turnstile.
Complementary accessories:

001PSSL90 - Leaf 900 mm;
001PSSL120 - Leaf 1,200 mm;
001PSSLC - Customized leaf, dimensions on request;
001PSSA01 - Control radar (optional);
001PSSA03 - Plastic sleeve for fastening the barrier (optional);
001PSSA04 - STAINLESS STEEL sleeve for fastening the barrier (optional).

Code keys

Hole cover

Ferrite

Motor-powered turnstile

 This symbol shows which parts to read carefully.

⚠

This symbol shows which parts describe safety issues

☞ This symbol shows which parts to tell users about.

Type

PSSLN40

Protection rating (IP) 40
Power supply (V - 50/60 Hz) 120 / 230 AC
Motor power supply (V) 24 DC
Draw (mA) 350 mA
Power (W) 120
Operating temperature [°C] -20 ÷ +55
Insulation class I
Weight (kg) 17

4

2

5

5

2

1

8

9

10

11

7

6

3

650

1020

ø 120

900

1320

ø 120

1200

260

650

1008

260

1008

(001PSSL90) (001PSSL120)

p.

4

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Main components

1. Insulation tube

2. Inspection cover frame

3. Inspection hatch

4. Bushing-covering

5. leaf

6. Sliding flange

7. Extension sleeve

8. Upper cap

9. Internal rotating tube

10. Central column

11. Luminous LED crown with support

Dimensions

(mm)

p.

5

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Cable types and minimum thicknesses

Tools and materials

Make sure you have all the tools and materials you will need for installing in total safety and in compliance with ap­plicable regulations. The figure shows some of the equipment installers will need.

System feasibility

Preliminary checks

⚠

Only skilled, qualified staff must install this product.

⚠

Before beginning, do the following:

• Have in place a suitable dual pole cut-off switch with minimum contact openings of 3 mm, and section the
power supply;

• Set up suitable tubes and conduits for the electric cables to pass through, making sure they are protected from
any mechanical damage;

•

Make sure that any connections inside the container (ones that ensure continuity to the protection circuit)

are fitted with additional insulation with respect to those of other electrical parts inside;

• Make sure the passage area is in a proper state and without any dips.

• Set up barriers around the installation site during mounting operations, and an alternative route.

If cable lengths differ from those specified in the table, establish the cable sections depending on the actual power
draw of the connected devices and according to the provisions of regulation CEI EN 60204-1.
For multiple, sequential loads along the same line, the dimensions on the table need to be recalculated according to the
actual power draw and distances. If connecting products that are not contemplated in this manual, see the literature
accompanying said products

Connection Cable type

Cable length

1 < 20 m

Cable length

20 < 30 m

Control panel power-supply

FROR CEI 20-22

CEI EN

50267-2-1

3G x 1.5 mm

2

3G x 1.5 mm

2

Command and safety device 2 x 0.5 mm

2

2 x 0.5 mm

2

Control devices (RBM84-CRP)

CAT 5 -U/UTP

AWG 24

1000 m max.

Paired connection

1

2

3

4

2

p.

6

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Standard installation

1. Swing-leaf turnstile

2. Control device

3. Barrier

4. Junction box

Applicative examples





p.

7

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Installing

⚠

The following illustrations are mere examples. Consider that the space available where to fi t the operator and

accessories will vary depending on the installation site. It is up to each installer to select the most suitable solution.

⚠

Careful! Use hoisting equipment to transport and position the turnstile.
During the pre-mounting and fastening stages, the turnstile could be unstable and it could tip over. So, be careful to
not lean on it until it is completely anchored.

Preliminary steps



²

p.

8

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

39

22,5 22,5

45

1

2

p.

9

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Preparing the site and the turnstile base

Check that there are no dips in ground where you will anchor the turnstile.
Position the anchoring base as shown in the drawing (the leaf is perpendicular to the wall). Mark the anchoring holes
with a pencil.
Note: when installing up against walls, respect the minimum distance of 40 mm.

Fit conduits and run the cables through (see the "cable types and minimum thicknesses" table).

Leaf

Wall

Drill the marked spots.
Before anchoring the turnstile to the ground, distribute the electric cables inside the column (see the drawing).
Note: apply the ferrite to the controls / accessories cables.

Ferrite

2

1

1

2

N

L

p.

10

10

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Position the base on the anchoring spot and level it, if necessary, by using the adjusting screws.

NETWORK POWER SUPPLY 230V AC (Factory

configuration)

NETWORK POWER SUPPLY 120V AC

(Invert cables 1 and 2 as shown)

Fastening the turnstile to the ground

Connect the line power supply to the card terminal
housed in the back of the central column.

Ref. Description

Ⓝ

Neutral

Ⓛ

Line

Ground

①

RED cable: power supply 230 V AC to
transformer (line fuse 1.6 A-F)

②

BLACK CABLE: power supply at 120 V AC
to transformer (line fuse 3.15 A-F)

Power supply cable

EMC fi lter

²



²

p.

11

11

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

² ²

p.

12

12

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

At this point of the mounting, use the
control panel to check that the turnstile
works properly (the direction of travel
and speed), see the paragraph on the
control panel functions.





p.

13

13

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Center the tube with the control panel.

1

6

5

13

12

11

10

16

14

15

4

17

3

2

9

8

7

18

p.

14

14

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Description

Main components

Command and control electronics

The control panel is powered at 24 V AC.
The control devices and accessories are powered at 24 V. Careful! The accessories must not exceed 10 W overall.
All connections are quick-fuse protected.
Functions on input and output contacts and time and user management details, are set up and viewable on the
software-managed control panel's display.

⚠

Warning! Before intervening on the control panel, cut off the main power supply.

1 Programming buttons
2 Programming warning LED
3 Memory roll card connector
4 R700 card connection of the first control device
5 R700 card connection of the second control device
6 Display
7 Control devices or paired connection terminals
8 Warning devices temrinals
9 Connector for LED luminous band
10 Transponder terminals
11 Control devices terminals
12 Accessories power supply terminals
13 Control board power supply terminals
14 Accessories fuse
15 Control board fuse
16 Motor connector/encoder
17 LED power on warning
18 Line fuse

Warning LED

Green LED Flashing Leaf/leaves opening

Red LED

Turned on
steady

Stand-by

Slow fl ashing Leaf/leaves closing

Quick fl ashing

Prefl ashing time before the leaf closing phase
Stop button (N.C. contact)

Blue LED

Flashing Automatic closing time

FUSE TABLE

Line fuse

1.6 A-F (230 V)

3.15 A-F (120 V)

Accessories fuse 1 A-F
Control unit fuse 630 mA-F

1 2 3 4 2 C

X

A B GND

A B GND

24V 0V10 11

4 2 CX CY

S1 GND S1 GND C NO1 NO2

24V 0V10 11

p.

15

15

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Electrical connections

Power supply

LED luminous crown for warning about
the turnstile's state (see the paragraph on
"warning LED").

Warning devices

Control device

Terminals for 24 V AC

power supply to the acces-

sories.

Overall allowed power:

10 W

Power supply

24 V AC

Network power

supply󱊡

Transformer

Clean contacts (NO) for connecting to warning devices. Contact rated at: 24
V - 500 mA.

Terminals C-NO2 = open leaf warning (or contact for additional alarm.
See F-70).
Terminals C-NO1 = warns that leaf is closed.

24 V DC gearmotor with encoder

Gearmotor with encoder

TOR 300 - paired
connection.
Connection to a second
Came turnstile.

RBM84 - Access control.
Connection to Came
access control systems.

CRP - Came Remote
Protocoll.
Connection to Came home
& building automation
systems.

󱊡Set up for 230 V power supply. Change line fuse if powered at

120 V.

S1 GND S1 GND C NO1 NO2

1 2 3 4 2 CX CY

S1 GND S1 GND

A B GND

C NO1 NO2

TSP00LT001

CANCELLI AUTOMATICI

R700

p.

16

16

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Command and control devices

Stop button (N.C. contact) - For stopping the turnstile
while excluding the automatic closing cycle. To

resume movement, press the control button.

N.B.: if the contact is unused, select 0 (Deacti­vated) in function F 1.

Contact (N.O.) for opening devices. For
details see function F 54.

Contact (N.O.) for closing devices. For details
see function F 54.

Contact (N.O.) of the fi rst SENSOR 1 control device (Transponder or card
reader with R700 card)

Contact (N.O.) of the second SENSOR 2 control device (Transponder or
card reader with R700 card)

Black

Red

Contact (default: NC) for safety devices. For details
see functions F2, F54 and F72.

Other connections

Memory Roll

Black

Red

Contact (default: NC) for safety devices. For details
see functions F3, F54 and F72.

The R700 decoding cards are for controlling the turnstile fitted with the TSP00/LT001 sensors, the

to

save and upload of the settings including the registered users in another card.

For proper operation, before fitting any plug-in card (e.g.: the AF or the R700) YOU MUST CUT OFF THE MAIN

POWER SUPPLY and disconnect any emergency batteries.

1

8

p.

17

17

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Programming

Description of programming commands

The button is for

• entering the programming

• entering the single menus

• confirming/memorizing the set value
The key

are for

• moving from one item to another

• increasing or decreasing values

The key

is for exiting menus without

saving the changes

Display for viewing
functions and settings
that are assigned via the
programming buttons.

Menu map

Start programming by first performing functions A 2 Motor test and A 3 Travel calibration.

F 1 Total stop
F 2 Setup input 2-CX
F 3 Setup input 2-CY
F 19 Automatic closing
F 21 Preflashing
F 28 Opening speed
F 29 Closing speed
F 30 Opening slow-down
F 31 Closing slow-down
F 34 Travel sensitivity
F 35 Slow-down sensitivity
F 49 Operation
F 50 Saving data
F 51 Read data
F 52 Copy parameters from Master to Slave
F 53 AntiPassBack
F 54 Entry direction

F 55 Standard alarm
F 56 Peripheral number
F 57 Offset closing limit-switch
F 62 Automatic restoring
F 70 Additional alarm
F 72 Change state of safety contacts

U 1 Memorizing a user
U 2 Deleting a user
U 3 Deleting all users

A 2 Motor test
A 3 Calibrating boom travel
A 4 Resetting parameters

H 1 Firmware version

p.

18

18

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Function

Descripton (

negative

[ ]

default values

)

F-1 Total Stop. With button connected to terminals 1-2.

[ ] To deactivate it (this is obligatory when thereis no button); [ ] to activate it.

F-2 Input 2-CX setup. Choosing the function activated by the connected device.

[

] To deactivate it; [ ] for the reopening during closing phase function; [ ] for the obstruc-

tion wait function.

F-3 Setup input 2-CY. Choosing the function activated by the connected device.

[

] To deactivate it; [ ] for the closing phase reopening function; [ ] for the obstruction wait

function.

F-19 Automatic closing. The automatic closing timer activates when the leaf reaches the opening

limit-switch. The preset time is adjustable, and is in any case subject to the intervening of any
safety devices and it deactivates after a total safety "stop" or during power outages.

[

…… ] setting between 1 and 60 seconds.

F-21 Preflashing. After a closing command, the luminous LED band connected to the control board

flashes for a settable time before starting the maneuver.
[

] To deactivate it; [ …… ] setting from 1 to 5 seconds.

F-28 Opening speed. Setting the speed during the opening maneuvers, calculated as a percentage.

[

…… ] Setting from 40 to 100% of the motor speed.

F-29 Closing speed. Setting the speed during the closing maneuvers, calculated as a percentage.

[

…… ] Setting from 40 to 80% of the motor speed.

F-30 Opening slow-down. Setting the speed during opening slow-downs, calculated as a percent-

age.
[

…… ] Setting from 20 to 30% of the motor speed.

F-31 Closing slow-down. Setting the speed during closing slow-downs, calculated as a percentage.

[

…… ] Setting from 20 to 30% of the motor speed.

F-34 Travel sensitivity. Setting the obstruction detection sensitivity during maneuvers.

From maximum [

… ] to minimum [ … ] sensitivity.

F-35 Slow-down sensitivity. Setting the obstruction detection sensitivity during slow-downs.

From maximum [

… ] to minimum [ … ] sensitivity.

F-49 Gestione. Setting the turnstile operating modes.

[

] Stand Alone operation; [ ] paired connection operation; [ ] operation from RBM84 access

control; [ ] operation via CRP (Came Remote Protocol).

F-50

Saving data. Saving registered users and all settings in the

.

The function appears only with connected.

[

] To deactivate it; [ ] to activate it.

F-51

Data reading. Uploading all data from

.

The function appears only with connected.

[

] To deactivate it; [ ] to activate it.

F-52 Copy parameters from Master to Slave. See details in the “Paired connection” section.

[

] To deactivate it; [ ] to activate it.

F-53 Antipassback. To prevent a card from being used for two or more consecutive entries in the

same area.
[

] To deactivate it; [ ] to activate it.

Functions details

p.

19

19

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Function

Descripton (

negative

[ ]

default values

)

F-54 Direction of entry. Setting the direction of entry.

[ ] Commands: on 2-3 counter-clockwise opening; on 2-4 closing.

Safeties: on 2-CX and 2-CY they intervene in both rotations.

[

] Commands: on 2-3 clockwise opening; on 2-4 closing.

Safeties: on 2-CX and 2-CY they intervene in both rotations.

[

] Commands: on 2-3 counter-clockwise opening; on 2-4 clockwise opening.

Safeties: on 2-CX the intervene during the counter-clockwise rotation; on 2-CY they inter­vene during the clockwise rotation.

[ ] Commands: on 2-3 clockwise opening; on 2-4 counter clockwise opening.

Safety devices: on 2-CX intervene in the clockwise rotation; on 2-CY intervene in the
counter clockwise rotation.

F-55 Standard alarm. Setting the internal buzzer's activation time. It activates when contacts 2-CX

and 2-CY open with the leaf closed or during the pre-flashing phase set up on F-21.
[

] To deactivate it; [ …… ] setting between 1 and 60 seconds.

F-56 Peripheral number. If the turnstile is managed by the RBM84 access control (see F-49), it is

best to assign a univocal number to each one.
[

…… ] The maximum number of allowed turnstiles is 255.

F-57 Offset closing limit-switch. See detail in the "Offset closing limit-switch" chapter.

From -45° [

] to no setting [ ] to +45° [ ].

F-62 Automatic restoring. Restoring time of the closing leaf, after manually forcing it.

[

…… ] Setting between 1 and 10 seconds.

F-70 Additional alarm. It changes function to terminal C-NO2 (leaf open) for connecting a sound

alarm device.
[

] To deactivate it; [ ] to activate it.

F-72 Change status of contacts. It varies the (NO/NC) state of the safety contacts CX and CY. It is

for connecting any accessories with NO contacts (such as a sensitive-plate).

[ ] CX becomes NO; [ ] CY becomes NO; [ ] both NO.

U-1 Memorizing a user. See detail in the "Entering a user" chapter.
U-2 Deleting a user. See detail in the "Deleting a user" chapter.
U-3 Completely deleting users. Deleting all memorized users. Once deleted the following [ ] will

appear.

[ ] to delete all users.

A-2 Motor test. See detail in the "Motor test" chapter.

[

] To deactivate it; [ ] to activate it.

A-3 Calibrating travel. See details in "Calibrating travel".

[ ] to deactivate it.

A-4 Reset parameters. Deleting the entire programming

(including travel calibration) and returning to
default parameters.

[ ] to restore all default parameters.

H-1

Firmware version. Views the firmware version. For example [ ]

---

ESC < > ENTER

ESC < > ENTER

oP I

cl I

cl i

op I

=

=

p.

20

20

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Activate procedure A 2, see Functions detail table.

Activate procedure A 3, see Functions detail table.

After pressing, the

waiting [ ] will

appear.

Keeping the button pressed, check
that the turnstile performs a CLOCKWISE
maneuver.

Then, use the button

to check that
the turnstile performs a COUNTER
CLOCKWISE maneuever.

If the rotations are correct, move on to travel calibration.

Motors test

After pressing, the

leaf will
perform a clockwise movement until it
mechanically stops.

Then an inverted movement until the final
mechanical stop.

Before calibrating the travel, check that the maneuvering area is free of any obstructions.
During the calibration, all of the safety devices will be disabled except for the Total Stop.

Travel calibration

Wait a few seconds for the registrations to
appear on the display.

The leaf closing position is established as the bisector of the final closing stops.

Always start programming the turnstile from this procedure.

󱊡With an entry direction other than the default one (see function F-54) the direction of opening could be

inverted.

ESC < > ENTER

ESC < > ENTER

5

i

ESC < > ENTER

75F

5

-

i

75F

ESC < > ENTER

p.

21

21

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

O set closing limit-switch

Select F 57. Press
ENTER to confirm.

Press the > arrow key
to compensate the limit­switch closes counter
clockwise ...

Press ENTER to
confirm.

After calibrating the travel, the O set closing limit-switch operation allows you to further adjust the position of
the closed leaf, as illustrated in the examples.

... or the < arrow key to
compensate the limit­switch closes clockwise.

ESC < > ENTER

ESC < > ENTER

ESC < > ENTER

<

<

> EN

>

>

ESC < > ENTER

<

<

> ENTE

EN TE

>

>

C

L

I

U

i

i

2

U

2

2

2

2

ESC < > ENTER

i

2

p.

22

22

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Select U 1
Press ENTER to confirm.

Select 1 to activate the entering of a user via transponder
card. Press ENTER to confirm.

A progressive number between 1 and 150
will appear and flash for a few seconds.
Send the code via transponder card or
other control device. The number stays
fixed for an instant to show that the user
registration has been completed...

Select U 2. Press ENTER to confirm.

Select the number of the user to delete by using the arrow keys.
Press ENTER to confirm.

... Clr will appear on the screen to confirm deletion.

Entering users

Deleting a single user

The number will flash for a few sec­onds, press ENTER to reconfirm ...

... then, another progressive number will appear and flash for
the next user registration.

N.B.: when entering and deleting users, the numbers that appear fl ashing are available and usable numbers for
entering new users (max. 150 users).

☞Note: fill in the table on the following page to have a registered-user report.

1)

2)

3)

4)

5)

6)

7)

8)

9)

10)

11)

12)

13)

14)

15)

16)

17)

18)

19)

20)

21)

22)

23)

24)

25)

26)

27)

28)

29)

30)

31)

32)

33)

34)

35)

36)

37)

38)

39)

40)

41)

42)

43)

44)

45)

46)

47)

48)

49)

50)

51)

52)

53)

54)

55)

56)

57)

58)

59)

60)

61)

62)

63)

64)

65)

66)

67)

68)

69)

70)

71)

72)

73)

74)

75)

76)

77)

78)

79)

80)

81)

82)

83)

84)

85)

86)

87)

88)

89)

90)

91)

92)

93)

94)

95)

96)

97)

98)

99)

100)

101)

102)

103)

104)

105)

106)

107)

108)

109)

110)

111)

112)

113)

114)

115)

116)

117)

118)

119)

120)

121)

122)

123)

124)

125)

126)

127 )

128)

129)

130)

131)

132)

133)

134)

135 )

136)

137 )

138)

139)

140)

141)

142)

143)

144)

145)

146)

147)

148)

149)

150)

p.

23

23

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

List of registered users

ESC < > ENTER

94F

ESC < > ENTER

i

p.

24

24

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Paired connection

Specifi c connections

Setting and confi guring the MASTER turnstile

Connect the two TOR 300 control boards with the CAT 5 - U/
UTP - AWG 24 multi-pair woven unscreened cable to terminals
A-B-GND.

Connect all of the necessary devices onto
TOR 300 control board of the your MASTER
turnstile.

Set all functions and make all adjustments only on the MASTER turnstile.

Configure the control board as MASTER.
Select function F 49. Press ENTER to
confirm.

Set to 1=paired and press ENTER.

ESC < > ENTER

ESC < > ENTER

<

<

> EN

EN

>

>

cl i

op I

a3

i

ESC < > ENTER

ESC < > ENTER

EN

EN

i

25F

p.

25

25

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Travel calibration

Calibrate the MASTER control board
Select A 3 and press ENTER to confirm.

Select 1 and press ENTER to confirm the travel calibration
operation.

The leaves will perform a
slowed down maneuver until
the come to a full stop.

The leaves will perform an inverted maneuver until the come to
a full stop.

Transferring parameters from MASTER to SLAVE

To transfer the parameters from MASTER to SLAVE control
board, proceed as follows:

- select function F 52 on the MASTER control board.

- select 1 and press ENTER.
Note: with system that require the MASTER and
the SLAVE to have different parameters, make
the settings directly on to each control board.

Only the following parameters are copied:

- opening and closing maneuvering speeds;

- opening and closing slow-down speeds;

- opening and closing slow-down points;

- slow-down and travel sensitivity;

- calibrating speed.

p.

26

26

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

MAINTENANCE

Before doing any maintenance, cut off the power supply, to prevent any hazardous situations caused by acciden-

tally activating the operator.

To properly maintain the AISI 304 stainless steel, refer to the stainless steel cleaning part of the 119RW48

manual.

Table of the mean cycles between failures (MCBF) of Saloon turnstiles, considering proper installation and mainte­nance as described in this manual:

Model Operating limits MCBF

001PSSLN40

maximum number of daily cycles: 15,000

Maximum number of cycles per minute: 12 (1 cycle every 5 seconds)

1,200,000

Troubleshooting

PROBLEM POSSIBLE CAUSES FIXES AND REMEDIES
The turnstile does not

execute commands

• No power supply

• Stop button open

• Check power network

• Check proper state of the button

The turnstile stays open
after a passage

• Automatic closing function deactivated

• Photocells employed

• Call assistance

• Call assistance

Periodic maintenance

• Every 400,000 cycles and in any case every six

months:

• With the main power cut off, check for smooth
sliding and gearmotor reversibility.

• Check proper fastening of nuts.

• Check proper fastening of external tube
screws.

• Check proper fastening of ground anchoring
bolts.

• Clean the inside of the operator from any dust
created during operation.

• Cleaning/lubricating the plastic parts that slide
in contact with the aluminum tube.

• Check that all electrical and wiring connec­tions are sound and replace any damaged
parts.

• Cleaning of the outer tube (clean with a water­dampened cloth).

• Keep the stop-go light clean (clean with a
water-dampened cloth).

• If a radar is installed, keep the glass clean
(clean with a water-dampened cloth).

• Check proper positioning of the leaf when
opening and closing (possibly reset the
parameters by following the instructions in the
installation manual).

p.

27

27

- Manual code:

FA00 06

FA0006

8- EN

8-EN

v.

1

1

04/2015 © Came S.p.A. - The data and information in this manual may be changed at any time and without notice.

Error messages and notices during installation

MESSAGE CAUSE FIXES
Er3 • Encoder broken • Replace the encoder
Er5 • Exceeded travel time • Check operation of the gearmotor
Er6 + sound signal • The encoder has detected an obstruc-

tion three consecutive times

• Remove the obstruction and give a
command

Er8 • COM port error • Check connection A-B-GND and the

setting for function F49

C0 • Contact 1-2 (Stop) unused • Deactivate with function F1
C1 • Contact CX and/or CY unused • Deactivate with function F2/F3
Flashing red LED • Travel is not calibrated yet • Calibrate the travel

DISMANTLING AND DISPOSAL

At its premises CAME S.p.A. employs the UNI EN ISO 14001 compliant Environmental Management System, to

certify that the environment is respected and safeguarded.
Please continue safeguarding the environment. At CAME we consider it one of the fundamentals of our operating and

market strategies. Simply follow these brief disposal guidelines:

DISPOSING OF THE PACKAGING

The packaging materials (cardboard, plastic, and so on) should be disposed of as solid urban waste, and simply
separated from other waste for recycling.

Always make sure you comply with local laws before dismantling and disposing of the product.
DO NOT DISPOSE OF IN NATURE!

DISMANTLING AND DISPOSAL

Our products are made with different materials. Most of these (aluminum, plastic, iron, electrical cables) is classified
as solid urban waste. It can be recycled by separating it before dumping at authorized city dumps.

Whereas other components (control boards, batteries, transmitters, and so on) may contain hazardous pollutants.
These must therefore be disposed of by authorized, certified professional services.

Before disposing, it is always advisable to check with the specific laws that apply in your area.
DO NOT DISPOSE OF IN NATURE!

DECLARATION OF CONFORMITY

Declaration - Came S.p.A. declares that this device conforms to the essential, pertinent requirements provided by
directives 2006/42/EC and 2014/30/UE.
An original copy is available on request.

www. came.com

www. came.com

Came S.p.A.

Came S.p.A.

Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c

31030

Dosson di Casier

Dosson di Casier

Treviso

Treviso - Italy

33079

Sesto al Reghena

Sesto al Reghena

Pordenone

Pordenone - Italy

([phone]
([phone]

([phone]

([phone]

English

English - Manual code:

FA00 0

FA000

68 -EN

68-EN v.

1

1 04/2015 © Came S.p.A.

The data and information in this manual may be changed at any time and without notice.