CAME KRONO KR300, KRONO KR310, KRONO KR510 Installation Manual
KRONO SERIES
INSTALLATION MANUAL
KR300 - KR310 - KR510
AUTOMATION FOR SWING GATES
nglis
h
ENGLISH
ENGLISH
CAME cancelli automatici s.p.a.
Via Martiri della Libertà, 15
31030 Dosson di Casier
TREVISO - ITALY
www.came.it - info@came.it
WARNING!
Important instructions for the safety of people:
READ CAREFULLY!
Foreword
• Use of the products must be restricted to its intended use
(i.e. that for which it was expressly built for). Any other use is
to be considered dangerous. Came Cancelli Automatici S.p.A.
is not liable for any damage resulting from improper, wrongful
or unreasonable use • Keep these warnings with the installation and use manuals issued with the automated system.
Before installing
(preliminary check: in case of a negative
outcome, do not proceed before having
complied with the safety obligations)
• Make sure that the parts you intend to automate are in
good working order, and that they are properly balanced
and aligned. Also, make sure that proper mechanical stops
are already in place • If the operator will be installed at a
height of less than 2.5 m from the ground or other access
level, check whether you will need any protections and/or
warnings • Any gate leaves, fi tted with pedestrian entrances,
onto which you will install an operator, must have a blocking
mechanism when the gate is in motion • Make sure that the
opening of the automated gate is not an entrapment hazard
as regards any surrounding fi xed parts • Do not mount the
operator upside down or onto any elements that may fold
under its weight. If needed, add suitable reinforcements at
the points where it is secured • Do not install onto gates on
either an upward or downward slope (i.e. that are not on fl at,
level ground) • Check that any lawn watering devices will not
wet the gearmotor from the bottom up.
Installation
• Carefully section off the entire site to prevent unauthorised
access, especially by minors and children • Be careful when
handling operators that weigh more than 20 Kg (see installation manual). In such cases, employ proper weight handling
safety equipment • All opening commands (e.g. buttons, key
selectors, magnetic detectors, etc.) must be installed at least
1.85 m from the gate’s area of operation perimeter - or where
they cannot be reached from the outside of the gate. Also,
the direct commands (e.g. push button, or proximity devices,
etc.) must be installed at a height of at least 1.5 m and must
not be accessible to the public • All ‘maintained action’ commands, must be placed where the moving gate leaves, transit
areas and driveways are completely visible • If missing, apply a permanent label that shows the position of the release
mechanism • Before delivering to the client, verify that the
system is EN 12453 (impact test) standard compliant. Make
sure that the operator has been properly adjusted and that the
safety and protection devices, as well as the manual release
are working properly • Where necessary and in plain sight,
apply the Warning Sings (e.g. gate plate).
Special instructions and
advice for users
• Keep the gate’s area of operation clean and clear of any
obstacles. Trim any vegetation that may interfere with the
photocells • Do not allow children to play with the fi xed command devices, or in the gate’s area of operation. Keep any
remote control devices (i.e. transmitters) away from the children as well • Frequently check the system, to see whether
any anomalies or signs of wear and tear appear on the moving
parts, on the component parts, on the securing points, on the
cables and any accessible connections. Keep any joints (i.e.
hinges) lubricated and clean, and do the same where friction may occur (i.e. slide rails) • Perform functional tests on
photocells and sensitive edges, every six months. Keep glass
panels constantly clean (use a slightly water-moistened cloth;
do not use solvents or any other chemical products) • If the
system requires repairs or modifi cations, release the operator
and do not use it until safety conditions have been restored
• Cut off the power supply before releasing the operator for
manual openings. See instructions • Users are FORBIDDEN
to carry out ANY ACTIONS THAT THEY HAVE NOT BEEN
EXPRESSLY ASKED TO DO OR SO INDICATED in the manuals. Any repairs, modifi cations to the settings and extraordinary maintenance MUST BE DONE BY THE TECHNICAL
ASSISTANCE STAFF • On the periodic maintenance log, note
down the checks you have done.
Special instructions and
advice for all
• Avoid working near the hinges or moving mechanical parts
• Stay clear of the gate’s area of operation when in motion •
Do not resist the direction of movement of the gate; this may
present a safety hazard • At all times be extremely careful
about dangerous points that must be indicated by proper
pictograms and/or black and yellow stripes • When using
a selector or command in ‘maintained action’ mode, keep
checking that there are no people in the area of operation of
the moving parts. Do this until you release the command •
The gate may move at any time without warning • Always cut
the power when cleaning performing maintenance.
EN
ENGLISH
1. GENERAL POINTS
These general conditions shall apply to all purchase agreements for Came Cancelli Automatici SpA materials, hereinafter called “the
company”.
2. OFFE RS AND Q UOTATIONS
The company’s quotations are valid for a 30-day period at the most starting from the date they are sent.
3. ORDERS
The sale agreement is executed once the written order is confirmed by Came Cancelli Automatici Spa or when the order is fulfilled by
the company. Orders that are addressed, and signed by clients, to Came Cancelli Automatici SpA are deemed to be firm and irrevocable
for 30 days starting from the date they are received by the company. Any change or addition to the single provisions of these general
conditions or single provisions of the order which was originally addressed by the client, shall have no validity unless other wise approved
in writing by the company. For any changes to the order, the company reserves the right to cancel both the changes an the original order.
The delivery date for the goods appearing on the orders is always and in any case exclusively indicative, and any delays of such term may
never justify claims for compensation or cancellation of contract.
Particularly, the company reserves the right to extend the delivery terms or cancellation of order in the event of: force majeure or events
that are beyond the control of the company; change of the Client’s legal status; dif ficulty in sourcing raw materials and component parts.
4. DELI VERY AND FORWARDING
The place of production or registered office of the company shall be the place of fulfilment for delivery. The cost and risk of the travelling
goods is borne by the buyer ex works, pursuant to the 2000 incoterms. Unless otherwise agreed, the company establishes, for and on
behalf of the client, the type of shipping, the travel route and type of carrier. The company reserves the right to carr y out partial deliveries
and fulfilment of orders, thereby issuing a separate invoice each time: in this case all partial deliveries shall be autonomously invoiced and
the terms of payment shall begin as of the date on each invoice; the client may not, therefore, defer payment of partial orders, until the last
deliver y is made as concerns the original order.
5. PRICES AND PRICE LISTS
The prices are intended for goods delivered free to the company’s registered office, not including VAT, with normal packaging, and not
including forwarding expenses. Any reference to list prices shall refer to the latest price list published by the company, which theretofore
cancels any previous price lists.
6. PAYMENTS
Non-payment within the established terms, shall result in the application of interest pursuant to Lgs. Decr. 09/10/2002 n. 231 and
subsequent amendments and upgrades, with any possible greater damage unprejudiced. Any delay in payment, shall mean that the client
shall owe the company, any losses due to exchange rates. The client may not advance any demands nor raise any exceptions as concerns
the company, unless after having paid the goods it purchased. The company reserves the right to block all shipping and supply orders
underway in the face of any irregularities in the payments, without need of prior notice nor compensatory damages of any kind.
7. RETURNS AND CLA IMS
All claims must be filed in writing within 8 days of receiving the goods, whether such claims refer to the quantit y or quality of the delivered
goods. Returned goods shall be accepted by company only following a written agreement, and only for new and packaged goods. Any
returned goods must be complete of their relative transport documents, showing the company’s written authorisation to accept the
returned goods including the quality and quantity of the returned goods.
The returned goods shall not be accepted by the company unless carried out in the above mentioned manner and, especially, returned
goods shall not be accepted if received at any of the company’s premises.
8. GUARANTEE
The company guarantees the proper functioning of the products that it provides, as per the technical characteristics that are expressly
shown on its products’ technical sheets. The guarantee shall not apply in the case of any environmental interferences of any nature, which
could cause disturbances in the functioning of any existing or future installations (radio frequencies – proximity of electric power lines…).
The guarantee does not cover the normal wear and tear of the equipment, or mistakes made during the mounting phase or due to
maintenance flaws, and in any case it does not cover any cases in which flaws in the functioning can be traced back to factors stemming
from anything other than manufacturing.
The deadlines for filing a claim for any flaws or for the statute of limitations for actions to which the buyer is entitled are those foreseen by
Italian law. The company at its own leisure, may decide to withdraw any goods supplied which it has ascer tained as faulty, or decide to
repair said ascertained flaws. The client may not request to be compensated for any indirect damages, missed gains, production losses,
and in any case may not expect as compensation any sums greater than the value of the supplied components or products.
9. REPAIRS
Repairs to purchased items request by the client shall be carried out by the company following an agreement on the price of said repairs.
In any case the expenses for labour and shipping ( roundtrip) shall be borne by the client.
10. RESE RVATION OF TITLE
It is expressly agreed that, any delivered goods remain owned by the company until the client pays the entire balance, regardless of who
is in possession of said goods. Transport expenses and any other expenses needed to retrieve the equipment, therein including any
extraordinar y expenses as well as any repeatable ones, shall be borne by the client.
11. APPLICCABLE L AW – SETTLEME NT OF ANY DISPUTES Any arising dispute resulting from the sale agreement, shall be set tled
according to the Italian law, thereby excluding any other law and in supplement to the Vienna Convention on the international sale of
goods. All disputes shall be subject to Italian jurisdiction and come under the exclusive competence of the Tribunal of Treviso, Italy.
12. PROVISIONS ON THE SA FEGUARDING OF PERSON AL DATA.
Pursuant to current legislation for the safeguarding of personal data, clients are aware that their personal data is inputted into the
company’s databank, which is necessary for the proper carr ying out of the contractual relationship and for compliance with cer tain
provisions of law, as well as for purposes of statistics, promotion, marketing, commercial, credit protection, management and transfer of
the same .
The personal data of the buying par ty are processed through automated and paper-based tools by authorised persons, by using safety
procedures designed to guarantee confidentiality. The personal data of the client may by shared with Public Bodies, companies of the
group, credit recovery firms, or consor tiums or associations with business scopes, market research scopes, or marketing scopes. The
data processor shall be the company, and the client may address said company to uphold their own rights as per law. To this end the
buying party is aware that at any time it may access its personal data, ask that it be updated, corrected and/or prohibit it from being used.
General conditions of sale
Pag.
2
2 - Manual code:
119D S51
119 DS 51 ver.
4.0
4.0 03/2009 © CAM E cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
4.1 Gate Operator
This product is engineered and manufactured by CAME cancelli automatici s.p.a. and complies with current safety regulations.
Guaranteed 24 months if not tampered with.
The gearmotor is formed of a motor in an armoured die-cast aluminium casing and a die-cast aluminium reduction gear casing which
contains a worm screw – helical gear – lead screw system.
4 Description
2.1 Intended use
1 Legend of symbols
This symbol tells you to read the section with particular care.
This symbol tells you that the sections concern safety issues.
This symbol tells you what to say to the end-users.
2 Intended use and applications
The KRONO gearmotor is specifi cally engineered to automate residential and condominium swing gates.
The use of this product for purposes other than those described above and installation executed in a manner other than as
instructed in this technical manual are prohibited.
3 Reference Standards
“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS”
“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”
“THIS MANUAL IS ONLY FOR PROFESSIONAL OR QUALIFIED INSTALLERS”
2.2 Application
The company CAME cancelli automatici is ISO 9001:2000 quality certified; it has also obtained the ISO 14001 environmental
safeguarding certification. CAME engineers and manufactures all of its products in Italy.
This product complies with the following legislation: see declaration of compliance.
There are various models of the gearmotor available:
001KR300D - Right hand irreversible gearmotor for leaves up to 3m.
001KR300S - Left hand irreversible gearmotor for leaves up to 3m.
001KR310D - Right hand irreversible gearmotor with microswitches incorporated for stopping the leaf, for leaves up to 3m.
001KR310S - Left hand irreversible gearmotor with microswitches incorporated for stopping the leaf, for leaves up to 3m.
001KR510D - Right hand irreversible gearmotor with microswitches incorporated for stopping the leaf, for leaves up to 5m.
001KR510S - Left hand irreversible gearmotor with microswitches incorporated for stopping the leaf, for leaves up to 5m.
Accessories:
001KR001 - Yale lock with DIN key.
Type KR 510
Length of gate leaf (m) 22.53 4 5
Weight of gate leaf (kg) 1000 800 600 500 400
Type KR 300 - KR 310
Length of gate leaf (m) 22.53
Weight of gate leaf (kg) 800 600 400
#
#
1
2
3
4
6
5
7
8
#
#
956 (KR3)
1356 (KR5)
304 (KR3)
504 (KR5)
113
Pag.
3
3 -
Manual code
:
119D S51
119 DS 51 ver.
4.0
4.0 03/2009
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
Motor power supply: 230V A.C. 50/60Hz
Max draw.: 1,1 A
Power: 130W
Opening time (90°): 22s
Thrust: 400 - 3000 N
Duty Cycle: 30%
Condenser: 8 μF
Protection Rating: IP54
Weight: 10 kg
4.2 Technical features
4.4 Overall dimensions
4.3 Description of parts
1) Gearmotor
2) Tail hooking bracket
3) Tail articulated joint
4) Head bracket
5) Pinion
6) Self-locking nut UNI 7474 M8
7) Flexible washer Grower ø12
8) Self-locking nut UNI 7474 M12
Motor power supply: 230V A.C. 50/60Hz
Max draw.: 1,1 A
Power: 130W
Opening time (90°): 34s
Thrust: 400 - 3000 N
Duty Cycle: 30%
Condenser: 8 μF
Protection Rating: IP54
Weight: 12 kg
Motoriduttore KR300 / KR310 Motoriduttore KR510
Measurements in mm
Loading...