Camden Door Controls CV-940-TCP Installation Instructions

TCP-IP to RS232/422/485 Converter
1.0 Introduction
The CV-940-TCP is cost effective and highly integrated serial –to-Ethernet Converter. Embedding a 8051 CPU, 64KB OTP ROM, 32 K bytes SRAM, 10/100Mbps Ethernet and serial port support handshake RTS,CTS. CV-940-TCP Can control 1x RS232/422/485 devices located virtually anywhere (via Ethernet or Internet).
Automatically nds devices in the network Conguration
over driver panels, serial port, Telnet, web Browser, SNMP automatic mode switching between Driver and RAW mode Support TCP/IP, UDP, DHCP, PPPoE, Dynamic DNS.
CV-940-TCP
Installation Instructions
2.0 Features
• 3-in-1 RS-232\422\485 interface Max.230Kbps serial interface and 10\100 Mbps Ethernet
• Supports 4-and 2-wire Rs-485 with AUTO-SEND and built- in terminator
• Supports industrial 24 VDC power input and optional Power over serial
• Terminal block accessories for easy RS-422\485 serial wiring
• Supports IP conguration By MAC address
• Supports conguration store and copy for deployment
• Supports Driver, TCP server/Client, UDP Server/Client, Pair connection operation modes Easy and powerful
conguration program
• Approval CE, RoHS
3.0 Hardware Installation& Initial Setup RS-232 Pinout: (DB 9 Mail)
DB9 Male Signal I/O
PIN1 RXD IN
PIN2 TXD OUT
PIN5 GND -
PIN7 RTS OUT
PIN8 RTS IN
RS-422/485 Pinout: (Six Terminal from left)
Terminal
No
RS422
RS485
1 2 3 4 5 6
T+ T- R+ R- VIN GND
485+ 485- - + VIN GND
3.3 Connect to 10/100M
CV-940-TCP 10/100/M port connect to switcher or HUB use straight-Through Cable.
ATC-1000
RJ45 Jack Connector
RJ45 Plug Pin 1
3.4 Power Supply
CV-940-TCP TCP/IP converter can adopt the product’s 12V power adapter for power supply or adopt power from other DC power or device .( +9 - +24V@500-100mA )
3.5 CV-940-TCP LED Indication
LINK: Indication Ethernet link, Green on Ethernet Link
established
ACT: Data Sending /Receiving between Serial and the Ethernet
PWR: Indication Power
Straight through cable
Cable Wiring
1 2 3 6
Hub
RJ45 Jack Connector
1 2 3 6
Tx+ Tx­Rx+ Rx-
Page 1 of 4
CV-940-TCP
3.6 Connection Diagram RS232 Connection
PC RS233
DB9 Female DB9 Female
32 23 55GND GND
RS-485 Connection
485+(1) 485-(2)
CV-940-TCP
B A
RS-485
Device
DeviceDevice
Go to TCP Mode and put the settings as given in the picture
IMPORTANT: Port Number : 4001
IMPORTANT: Telnet Server/Client must be set to “Server”
Then go to UART and put the settings as given in the picture bellow:
IMPORTANT: Mode RS485; Baud Rate: 38400
4.0 Configuration and Operation
IMPORTANT:
Set up your computer to assign it a static IP address in the
192.168.2.2 to 192.168.2.254 range with a subnet mask of 255.255.255.0. This is necessary to ensure that your computer can communicate with your CV-940-TCP. If you put IP Address in the range 192.168.1.2 to 192.168.1.255 you will not be able to access the CV-940-TCP.
Step 1: Open your web browser and type http:192.168.2.1 in the browser’s address box. This address is a factory set IP Address of your CV-940-TCP. Press “Enter”.
Step 2: The “ID and Password required” prompt box will appear.
Type “admin” (default username) in the Username eld and type “system” (default password) in the Password eld. Click
“OK”. The setup screen will then appear.
IMPORTANT: These settings are important for connecting the Fingerprint readers, the rest, listed bellow are advanced and are not required.
4.2 The menu features as below:
User login to enter a password.
Default ID: admin
Default Password: system
Page 2 of 4
CV-940-TCP
All of the above functions are explained below:
4.3 Administrator Setup
Manager of the relevant setting page.
4.4 Authentication IP Configuration
The Users can change the username and password to prevent unauthorized access.
Login ID and password authentication, the maximum is 15 characters and numbers.
User name: default admin
Password: default system
4.5 System IP Configuration
The CV-940-TCP supports two IP connection types: Static IP, DHCP. These types are listed in the Web page for the
IP Conguration setting. Each setup screen and available
features will differ depending on what kind of IP connection types you select. Default is Static IP.
Static (or Fixed) IP IP Address: default 192.168.2.1
Subnet mask: default 255.255.255.0
Step 2: Enter Subnet mask
Step 3: Enter Gateway IP Address
Step 4: Enter primary DNS IP address
Step 5: click Update button
4.6 DHCP
Host name (Optional): default NETUART, maximum length
15 characters. If there is DHCP Server existing in your network environment or your subscribe a CABLE service from your ISP, you can
set IP conguration to DHCP to get a dynamic IP address.
The HOST Name is optional item depending on your DHCP Server settings.
5.0 System Status
This screen shows the ATC-100’s current status. All of the information’s provided is read-only.
Kernel version: the installed version of the kernel.
MAC Address: At present the device MAC Address
Nickname: the product model name of NETUART
System Status
5.0 Load default setting
Allow Users to reset the CV-940-TCP to return the initial value, but the Mac Address will not be updated.
Gateway: default 192.168.2.254
Primary DNS: default 192.168.2.253
If you are connecting thought a static of xed IP from your
network environment, perform these steps:
Step 1: Enter IP address
Load Default Setting EEPROM
5.1. Telnet
Telnet connection setting:
Telnet Server/Client: Currently used to determine the device is to the Telnet sever or Client.
If the server, shows this connection have to wait for the other side of the Port, if the Client, show that external connections to the Port.
Remote server IP Address: When the Client, to be connected to the other side of the server IP address.
5.2 Operation mode
The CV-940-TCP support four operation mode: TCP Server, TCP Client, UDP Server and UDP Client. These modes are listed in the Web page for the Operation mode setting.
Each setup screen and available features will differ depending on what kind of operation mode you select.
Page 3 of 4
CV-940-TCP
Default is TCP server.
5.3 TCP Server
Port Number: default 23, range 0 to 65535
If your device is acted as passive to accept commands from remote and data be guaranteed to be received by peer is your concern, then you can set CV-940-TCP as TCP Server. Be sure the value of item Port Number is same as your remote control application using.
Client mode inactive time out (minutes): default 20 (0=Disable)
If you want to keep the connection between CV-940-TCP and your remote control application always on, then set the value of item Client mode inactive time out (minutes)
to 0, otherwise, when the inactive time of no any trafc on
line reach the setting value, CV-940-TCP will terminate this connection.
5.4 TCP Client
Remote Connection port Number: default 23, range 0 to 65535
Remote Host IP Address: default 210.200.181.102
If your device is acted as active to report real- time status to remote and the data be guaranteed to be received by peer is concern, than you can set CV-940-TCP as TCP Client. Be sure the value of item Remote Connection port number is same as your remote control application using and set the correct value of Remote Host IP Address.
remote and the data be guaranteed to be received by peer is not your concern, then you can set CV-940-TCP as TCP Client. Be sure the value of item Remote connection Port Number is same as your remote control application using and set the correct value of Remote Host IP Address.
Telnet Control
6.0 UART control (RS-232)
The CV-940-TCP support three serial types: RS232,RS422 and RS485. The users can reference hardware diagram to directly select RS232,RS422 and RS485, no need select by software.
Baud Rate: default 57600, range 300bps to 230,4 Kbps
Character Bits: 5,6,7,8 (default)
Parity Check: None (default), even, odd, space, mark,
Stop Bits: 1(default), 1.5 or 2
Hardware Flow Control: None (default), CTS\RTS (or
Hardware)
5.5 UDP server
Local Port number: default 21, range 0 to 65535
If your device is acted as passive to accept commands from remote and data be guaranteed to be received by peer is not your concern, than you can set CV-940-TCP as UDP server. Be sure the value of item Local Port Number is same as your remote control application using.
5.6 UDP Client
Remote Connection port number: default 21, range 0 to 65535
Remote Host IP Address: default 192.168.2.2.
If your device is acted as active to report real-time status to
Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control
5502 Timberlea Blvd., Mississauga, ON Canada L4W 2T7
www.camdencontrols.com Toll Free: 1.877.226.3369
Page 4 of 4
File: CV-940-TCP Installation Instructions.indd R1 Revision: 24/08/2015 Part No.: 40-82B183
Loading...