TECTON USER MANUAL
USER MANUAL
TECTON POWER AMP SERIES
P.1
INFORMATION FOR USE FOR
TECTON 38.4, TECTON 32.4, TECTON 24.4,
TECTON 28.2, TECTON 22.2 and TECTON 14.2
TUM_GB_2004-2007-R2_12-2007
Copyright 2007 by CAMCO Produktions- und Vertriebs- GmbH
©
für Beschallungs- und Beleuchtungsanlagen
Fischpicke 5, D-57482 Wenden, Germany
Telephone +49 (0) 2762 408-0
IMPORTANT SAFETY INSTRUCTIONS
1) Read the information for use (user manual).
2) Please keep this user manual in a safe place during the lifetime of the amplifier. The user manual forms an integral part of the amplifier. Reselling of the
amplifier is only possible if the user manual is available. Any changes made to
the amplifier have to be documented in writing and passed on to the buyer in
the event of resale.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this amplifier near water (for example, in damp rooms or near a
swimming pool).
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the user
manual.
IMPORTANT SAFETY INSTRUCTIONS
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus that produce heat.
9) Protect the power cord from being walked on, pinched or damaged in any
other way. Pay particular attention to plugs and the point where they exit from
the amplifier.
The amplifier may only be used in accordance with the information provided
10)
in the user manual. Before and during the usage of the amplifier please ensure
that all recommendations, especially the safety recommendations as detailed in
the user manual, are adhered to.
The TECTON-Amplifier is designed for the amplification of pulsed audio signals
and the amplifier should only be connected to speakers with an average
impedance that is not lower than the impedances specified in points 3.8.2, 3.8.3
and 3.8.4.
11) Do not place this amplifier on an unstable cart, stand,
tripod, bracket, or table. The device may fall, causing
serious injury, and serious damage to the device itself.
12) The amplifier can only be disconnected from the power supply by removing
the plug, which must be freely accessible at all times. Unplug this amplifier
during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel.
13)
Servicing is required when
the power-supply cord or plug has been damaged,
liquid has been spilled or objects have fallen into the amplifier,
the amplifier has been dropped or damaged in any other way,
the amplifier has been exposed to rain or moisture,
when the amplifier exhibits a distinct change from its normal function or
performance.
USER MANUAL
TECTON POWER AMP SERIES
P.2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION – HIGH VOLTAGE HAZARDS
EXIST WITHIN THIS PRODUCT.
REFER ALL SERVICING TO
AUTHORISED PERSONNEL.
1. Read the information for use (user manual)
When shipping the TECTON amplifier, always use the original shipping carton
and packing materials. For maximum protection, repack the unit as it was originally packed at the factory.
EXPLANATION OF SYMBOLS / SAFETY
USER MANUAL
TECTON POWER AMP SERIES
P.3
THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS
VOLTAGE WITHIN THE PRODUCT’S ENCLOSURE.
THE EXCLAMATION MARK IS INTENDED TO ALERT THE USER
TO IMPORTANT INSTRUCTIONS ALSO FOR MAINTENANCE IN THE
LITERATURE ACCOMPANYING THE AMPLIFIER.
THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL ALERTS
THE USER TO DANGEROUSLY HIGH VOLTAGE AT THE SPEAKON
CONNECTORS THAT COULD POTENTIALLY BE LIFE THREATENING.
CAUTION – RISK OF ELECTRIC SHOCK – DO NOT OPEN.
WARNING – TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
AMPLIFIER TO RAIN OR MOISTURE.
THE AMPLIFIER MAY ONLY BE CONNECTED
TO A SOCKET WITH A CONNECTION TO GROUND.
2. Environments
Use this amplifier only in E1, E2, E3 or E4 environments according to EN55103-2
“Electro-magnetic compatibility – Product-family norm for audio, video and
audio-visual installations as well as for studio-and lighting-control installations
for professional applications – Part 2: Immunity“.
3. Ventilation
Slots and openings in the cabinet are provided for ventilation, to ensure reliable
operation of the amplifier and to protect it from overheating. These openings
must not be blocked or covered. This amplifier should not be operated unless
proper ventilation is provided or manufacturer’s instructions have been
adhered to.
4. Water And Moisture
Do not use this amplifier near water (for example, in a wet basement or near a
swimming pool).
5. Cleaning
Unplug this amplifier from the wall outlet before cleaning. Do not use liquid or
aerosol cleaners.
6. Power-cord Protection
Power-supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon them or against them, paying particular attention to cords and plugs, and the point where they exit from the amplifier.
7. Lightning
For added protection of this amplifier during lightning storms, or when it is
left unattended and unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the amplifier due to lightning and power-
SAFETY
line surges. Disconnection from the mains power supply can only be achieved
by removing the plug from the mains socket and by external disconnecting all
poles from the mains.
8. Interference of external objects and/or liquids with the appliance
Never push objects of any kind into this amplifier through openings as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the amplifier.
9. Accessories
Do not place this amplifier on an unstable cart, stand, tripod, bracket, or table.
The amplifier may fall, causing serious injury, and serious damage to the product.
Any mounting of the amplifier should follow the manufacturers instructions,
and should use a mounting accessory recommended by the manufacturer.
10. Connecting
When you connect the amplifier to other equipment, turn off the power and
unplug all of the equipment from the supply source. Failure to do so may cause
an electric shock and serious personal injury. Read the user manual of the other
equipment carefully and follow the instructions when making the connections.
11. Sound Volume
Reduce the volume to minimum before you turn on the amplifier to prevent
sudden high levels of noise which may cause hearing or speaker damage. (See
also 4.1.1 Volume control)
12. Damages that require service
Unplug this amplifier from the mains supply and refer to your dealer/distributor
or other authorised repair workshop if any of the following situations occur:
if liquid has been spilled, or objects have fallen into the amplifier.
if the amplifier does not operate normally as described in the user manual.
Operate the controls only as described in the user manual.
if the amplifier has been dropped or damaged in any other way.
when the amplifier exhibits a distinct change from its normal function or
performance.
13. Servicing
Do not attempt to service this amplifier yourself. As opening or removing covers
may expose you to dangerous voltage or other hazards, the amplifier may only
be opened by qualified personnel. Please refer to your dealer/distributor.
14. Servicing and Replacement Parts
All service and repair work must be carried out by a CAMCO authorised dealer.
When replacement parts are required, please ensure that the dealer/distributor
only uses replacement parts specified by the manufacturer. The use of unauthorized replacement parts may result in injury and/or damage through fire
or electric shock or other electricity-related hazards.
15. Safety Check
Upon completion of any service or repairs to this product, ask the dealer/
distributor to perform safety checks to determine that the amplifier is in proper
operating condition.
Recommendations on how to carry out the safety test can be found in DIN VDE
0701-1 “Maintenance, Modification and Test of Electronic Appliances“.
USER MANUAL
TECTON POWER AMP SERIES
P.4
EC Declaration of Conformity in accordance to EC Directives:
electro-magnetic compatibility (Council Directive 89/336/EEC,
as amended by Directives 92/31/EEC and 93/68/EEC);
low-voltage electrical equipment (Council Directive 73/23/EEC )
Manufacturers Name:
CAMCO Produktions- und Vertriebs- GmbH
für Beschallungs- und Beleuchtungsanlagen
Manufacturers Address:
Fischpicke 5, 57482 Wenden – Germany
Declares that the product with the model name:
CAMCO Power amplifier TECTON-38.4, 32.4, 24.4, 28.2, 22.2 and 14.2
Conforms to the following standards:
EN60065 Safety
EN55103-1 Emission
EN55103-2 Immunity
EC DECLARATION OF CONFORMITY
USER MANUAL
TECTON POWER AMP SERIES
P.5
The operating conditions and application environments presupposed in the
information for use (user manual) are to be kept accordingly.
Please Note: The following formulations have been chosen: TECTON-38.4,
TECTON-32.4, TECTON-24.4, TECTON-28.2, TECTON-22.2 and TECTON-14.2
for the type plate and the EC Declaration of Conformity. TECTON 38.4, TECTON
32.4, TECTON 24.4, TECTON 28.2, TECTON 22.2 and TECTON 14.2 for the front
face of the appliance and for the text in the user manual.
Wenden, 09.12.2004
Joachim Stöcker
CONTENTS
USER MANUAL
TECTON POWER AMP SERIES
P.6
P.2
IMPORTANT SAFETY INSTRUCTIONS
P.3
EXPLANATION OF SYMBOLS / SAFETY
P.5
EC DECLARATION OF CONFORMITY
P.6
CONTENTS
P.7
1 WELCOME
1.1 Welcome to CAMCO
1.2 Unpacking
P.8
1.3 The Amplifier
P.9
2 FACILITIES
2.1 TECTON – The Front
2.2 TECTON – The Rear
P.10
2.3 Factory Settings
P.11
3 INSTALLATION
3.1 Mains Supply
P.12
3.2 On/Off Switch
3.3 Mounting
P.13
3.4 Cooling
3.5 Ground Lift
3.6 Mode Indicators
P.14
3.7 Mode Selector
3.8 Wiring
3.8.1 E.U.I.2 and XLR Connection
P.15
3.8.2 Stereo Operation
3.8.3 Parallel-Mono Operation
3.8.4 Mono-Bridge Operation
P.16
3.8.5 SPEAKON Connection
P.17
4 OPERATION
4.1 Controls
4.1.1 Volume Control
4.1.2 Gain Selector
4.1.3 Gain and Input Sensitivity
4.1.4 Limiter Switch
4.1.5 HPF-Filter
P.18
4.2 Indicators
4.2.1 Output Current LEDs
4.2.2 Signal LEDs
4.2.3 Clip LEDs
P.19
4.3 Power Amp Protection Systems
4.3.1 Clip Limiter
4.3.2 SOA Protection
4.3.3 DC Protection
4.3.4 DC Servo
4.3.5 Over Current Protection
4.3.6 Thermal Protection
4.4 Mains Protections
P.20
4.4.1 Inrush Current Limitation
4.4.2 Mains Over Voltage Detection
4.4.3 Mains Failure Detection
4.4.4 Fuse Protection
4.5 Main SMPS Protections
4.5.1 Over Current Protection
4.6 Fans
5 OPTIONS
P.21
5.1 E.U.I.2 (Extended User Interface)
5.1.1 What Are The Possibilities
Using the E.U.I.2
6 TROUBLESHOOTING
P.22
6.1 Problem: No Sound
6.2 Problem: No Channel Separation
6.3 Problem: Distorted Sound
6.4 Problem: Hiss
6.5 Problem: Squeals and Feedback
7 SPECIFICATION
P.23
8 MEASUREMENTS
P.26
P.31
9 WARRANTY INFORMATION
9.1 Summary Of Warranty
9.2 Items Excluded From This Warranty
9.3 What CAMCO Will Do
9.4 How To Obtain Warranty Service
9.5 CAMCO’s Product Improvement
P.32
10 SERVICE INFORMATION
P.33
11 MAINTENANCE INFORMATION
12 DECOMISSIONING
P.34
COMPANY INFORMATION
1.1 Welcome to CAMCO
Established in 1983, CAMCO has gained worldwide experience with professional
sound reinforcement technology. Within the audio market, CAMCO specialises
in the production and marketing of high quality power amplifiers and sound
systems for use both on tour and in static installations.
WELCOME
The success of the LA, DL, DX and VORTEX series of power amps has made the
CAMCO name synonymous with professional quality, high performance and
utterly reliable power amps.
1.2 Unpacking
Please unpack and inspect your new amplifier for any damage that may have
occurred during transit. If damage is found, notify the transportation company
immediately. Only you, the consignee, may initiate a claim for shipping damage.
CAMCO will be happy to cooperate fully as needed. Please save the shipping
carton as evidence of damage for the shipper’s inspection.
Even if the amplifier has arrived in perfect condition, save all packing materials
so you will have them if you ever need to transport the unit.
USER MANUAL
TECTON POWER AMP SERIES
P.7
CAMCO’s commitment to research and development, seen not just in the area
of materials and technology but also most importantly in its highly skilled and
motivated workforce, is one of the keys to its ongoing success.
Welcome to the new world of professional power amplifiers –
WELCOME TO CAMCO!
NEVER SHIP THE AMPLIFIER WITHOUT THE ORIGINAL
PACKING MATERIALS.
When shipping the TECTON amplifier, always use the original shipping carton
and packing materials. For maximum protection, repack the unit as it was originally packed at the factory.
1.3 The Amplifier
The TECTON is a Class-H power amplifier with a power output of:
TECTON 38.4 1900 W per channel @ 4
3800 W in Mono-Bridge @ 8 Ω
3800 W in Parallel-Mono @ 2 Ω
TECTON 32.4 1600 W per channel @ 4
1 WELCOME
TECTON 24.4 1200 W per channel @ 4
TECTON 28.2 1420 W per channel @ 2 Ω
TECTON 22.2 1140 W per channel @ 2 Ω
TECTON 14.2 730 W per channel @ 2 Ω
3200 W in Mono-Bridge @ 8 Ω
3200 W in Parallel-Mono @ 2 Ω
2400 W in Mono-Bridge @ 8 Ω
2400 W in Parallel-Mono @ 2 Ω
2840 W in Mono-Bridge @ 4 Ω
2840 W in Parallel-Mono @ 1
2280 W in Mono-Bridge @ 4 Ω
2280 W in Parallel-Mono @ 1
1460 W in Mono-Bridge @ 4
1460 W in Parallel-Mono @ 1
Ω
Ω
Ω
Ω
Ω
Ω
Ω
TECTON amplifiers are fitted with Switched Mode Power Supplies (SMPS), which
significantly reduces the weight and size (only 2U) of the amplifier. Using SMPS,
the 2 symmetrical supply voltages (1 symmetrical supply voltage for
22.2 and TECTON 14.2) of the power amplifier are more stable than the power
supplies used in conventional amplifiers.
The TECTON has been designed as an intelligent and powerful product for
performing specialised tasks within a complex audio system. Users can adapt
the power amp to meet their specific audio requirements before use. Controls
mounted on the front and the rear of the TECTON allow access to the functio-
nality.
Since some of the externally mounted controls have multiple functions, it is
important that users should familiarise themselves thoroughly with the entire
range of controls.
If you have any questions regarding features and/or functions of your TECTON,
CAMCO will be pleased to provide you with further information. Alternatively,
contact your dealer or distributor.
TECTON
USER MANUAL
TECTON POWER AMP SERIES
P.8
2 FACILITIES
5 76
USER MANUAL
TECTON POWER AMP SERIES
P.9
2.1 TECTON – The Front
1 On/Off Switch
2 Volume Control – Channel B
3 Volume Control – Channel A
4 Operating Mode LEDs
5 Clip LEDs
6 Output Current LEDs
7 Signal LEDs (multifunctional)
17 18
19
1415 12 11 10 8916
2.2 TECTON – The Rear
13 24
8 AC Power Cable
9 SPEAKON Outlet A
10 SPEAKON Outlet B
11 Cooling Air Outlet Vents
12 XLR – Line Link A
13 XLR – Line Link B
21
20
13
22
14 Extended User Interface
(E.U.I. 2)
15 XLR – Line Input A
16 XLR – Line Input B
17 Input Ground Lift Switch
18 High Pass Filter B
OUTPUT B OUTPUT A
19 Mode Selector
20 Gain Selector
21 High Pass Filter A
22 Clip Limiter Switch
23 Rating Plate
23
2.3 Factory Settings
TECTON amplifiers are delivered with the following factory settings
2 FACILITIES
222120191817
P.10
3
Front panel:
1 On/Off Switch Off Amplifier is switched off
2 Volume Control - Channel B Off
3 Volume Control - Channel A Off
USER MANUAL
TECTON POWER AMP SERIES
2 1
Rear panel:
17 Input Ground Lift Grounded
18 High Pass Filter channel B Off
19 Mode Selector Stereo
20 Gain Selector 26 dB
21 High Pass Filter channel A Off
22 Clip Limiter Off
Make sure that the switches are set to the configuration needed for each particular application. For more detailed information, see sections 3.5, 3.7 and 4.1.
3.1 Mains Supply
When mounting or connecting the amp always disconnect it from mains.
Only connect the TECTON amplifier to a appropriate AC circuit and outlet,
according to the requirements indicated in the second line on the rating
plate.
3 INSTALLATION
TECTON-38.4
230 V ~ 50/60 Hz 11,3 A 1220 W
xxxxxxx
TECTON-32.4
230 V ~ 50/60 Hz 9,8 A 1010 W
xxxxxxx
TECTON-24.4
230 V ~ 50/60 Hz 10,5 A 1060 W
xxxxxxx
1900 W / 4 Ohm
1600 W / 4 Ohm
1600 W / 2,7 Ohm
TECTON-28.2
230 V ~ 50/60 Hz 9,5 A 1002 W
xxxxxxx
TECTON-22.2
230 V ~ 50/60 Hz 10,6 A 1120 W
xxxxxxx
TECTON-14.2
230 V ~ 50/60 Hz 7,4 A 712 W
xxxxxxx
Exemplary rating plates for a mains supply of 230 V ~ 50/60 Hz.
1400 W / 2 Ohm
1100 W / 2 Ohm
700 W / 2 Ohm
Power supply data:
Voltage Mains Frequency Current Power Consumption
TECTON 38.4 120 V 50/60 Hz 22,6 A 1220 W
TECTON 38.4 220 V 60 Hz 11,3 A 1220 W
TECTON 38.4 230 V 50/60 Hz 11,3 A 1220 W
TECTON 32.4 120 V 50/60 Hz 19,6 A 1010 W
TECTON 32.4 220 V 60 Hz 9,8 A 1010 W
TECTON 32.4 230 V 50/60 Hz 9,8 A 1010 W
TECTON 28.2 120 V 50/60 Hz 19 A 1002 W
TECTON 28.2 220 V 60 Hz 9,5 A 1002W
TECTON 28.4 230 V 50/60 Hz 9,5 A 1002 W
TECTON 24.4 120 V 50/60 Hz 21 A 1060 W
TECTON 24.4 220 V 60 Hz 10,5 A 1060 W
TECTON 24.4 230 V 50/60 Hz 10,5 A 1060 W
TECTON 22.2 120 V 50/60 Hz 21 A 1120W
TECTON 22.2 220 V 60 Hz 10,6 A 1120 W
TECTON 22.2 230 V 50/60 Hz 10,6 A 1120 W
TECTON 14.2 120 V
TECTON 14.2
TECTON 14.2
50/60 Hz 14,8 A 712 W
220 V 60 Hz 7,4 A 712 W
230 V 50/60 Hz 7,4 A 712 W
P.11
USER MANUAL
TECTON POWER AMP SERIES
3.2. On/Off Switch
The On/Off Switch is a rocker-type switch. It is located on the right side of the
front panel. To turn the amplifier on, push in on the upper part of the switch. This
initiates start-up by activating the inrush current limiter. During power up the
Clip and Signal LEDs from both channels will light up in red for a few seconds. To
turn the amplifier off, push in on the lower part of the switch.
3.3 Mounting
Use four screws and washers when mounting the amplifier to the front rack rails.
For mobile use, the amplifier should also be secured using the 19” mounting
elements on the rear panel.
10 mm
3 INSTALLATION
P.12
Amplifier is switched on Amplifier is switched off
NOTE: This switch does NOT disconnect the amplifier from mains.
Make sure the mains power socket or an alternative disconnect device is
near by and easily accessible.
The switch initiates start-up by activating the current limiting function.
As soon as the power amplifier is connected to the mains power supply, a voltage is supplied to both the line-filter and the fused input of the controllable
rectifier. Disconnecting the amplifier from the main power supply can only be
achieved by physically separating the amplifier from the mains by pulling the
mains plug. The mains plug therefore has to be freely accessible. Disconnect
the mains plug from the mains during a lightning storm or when the amplifier
remains unused or unsupervised for a prolonged period of time. Alternatively,
you can disconnect the amplifier via an external all-pole disconnection from
the mains.
If a power cut occurs while the amplifier is switched on, it will restart automatically once the power supply has been restored. All settings operation prior to
the loss of power will be maintained.
USER MANUAL
TECTON POWER AMP SERIES
88,9 mm
76,2 mm
330,7 mm
466 mm
442 mm
7 mm
7 mm
356,2 mm
347,2 mm
76,2 mm
10 mm
3.4 Cooling
Under normal operation of the power amp, overheating should never be a
problem. The air is taken in from the front and out through the back, it is of
course essential that while the power amp is running air is able to circulate
around it freely.
The efficiency of the cooling will depend on the immediate environment (e.g.
an enclosed rack, direct sunlight). If the amp is installed in a case, the open area
at the back of the case must be at least 140 cm². This area should be in line with
the amp.
3 INSTALLATION
If this can not be achieved a forced ventilation system has to be used.
3.5 Ground Lift
The input signal ground (pin 1 for all 4 XLRs) is connected to the ground of the
mains supply. In order to avoid ground loops, this connection can be separated
via a resistor. The ground potential of the power amp and the ground of the
loudspeaker always remain connected to the ground of the mains supply
regardless of the setting of this switch.
3.6 Mode Indicators
On the front panel there are two yellow LEDs to indicate the mode that is set. In
stereo mode (2-channel) none of them will be lit. In Parallel-Mono the (PM) LED
will be lit and in Mono-Bridge, the (MB) LED will be lit.
Amplifier in Parallel-Mono mode Amplifier in Mono-Bridge mode
P.13
Lift Position
to Pin 1
of the XLRs
Removing or taping the mains connector ground is illegal and dangerous.
Ground Position
DO NOT REMOVE MAINS CONNECTOR GROUND
IT IS ILLEGAL AND DANGEROUS
USER MANUAL
TECTON POWER AMP SERIES
3.7 Mode Selector
The switch on the rear panel changes the operating mode. Switch the power
switch to the Off position to make changes on the Mode Selector. When the
amplifier is switched on again, the selected mode will operate.
3.8 Wiring
3.8.1 E.U.I. and XLR Connection
XLR: Pin 1 = Ground (or lifted via 15 Ω resistor) (See 3.5 Ground Lift)
Pin 2 = Hot (inphase)
Pin 3 = Cold (out of phase)
Always use symmetrical (balanced) shielded cable to connect the amplifier.
3 INSTALLATION
P.14
USER MANUAL
TECTON POWER AMP SERIES
Channel B
To
Channel B
Input
Channel A
12
3
2
To
Channel A
Input
Ground
Lift
1
3
LINK BInput
132 2
Input Ground Lift in position:
grounded
LINK A
1
3
3.8.2 Stereo Operation, 2 Channel Operation
Two fully independent amplifier channels (normal operating mode).
3.8.4 Mono-Bridge Operation
One-channel mono bridged operation.
3 INSTALLATION
P.15
TECTON
A (L)
Z ≥ *Z
B (R)
Z ≥ *Z
3.8.3 Parallel-Mono Operation
Parallel operation of the two channels together.
TECTON
A
Z
res
≥ 0.5 *Z
The output terminals of the two channels are configured in parallel using an internal relay. The (single) load is connected either to the output of channel A or to
that of channel B (as if in stereo). While the total output of the amplifier remains
the same and the output voltage level is also the same as in stereo operation,
the minimum impedance that can be connected is reduced by half due to the
fact that current capability is doubled. Only channel A-Input is active. The channel B-Input is inactive – turn the volume of channel B down to zero.
This mode is useful when, for example, 3 identical loudspeakers are to be
operated with the same power.
USER MANUAL
TECTON POWER AMP SERIES
TECTON
min
A
min
Z ≥ 2 *Z
min
The second channel processes the same input signal, but with reversed phase.
The (single) load is connected between the two positive channel outputs using
a suitable connected SPEAKON connector. While the total output of the amplifier remains the same, both the available output voltage and the minimum
min
impedance that can be connected are doubled, as compared with stereo operation. Only channel A-Input is active. A signal feeding channel B will have no
effect on the output. Turn the volume of channel B down to zero.
WARNING !
In Mono-Bridge mode RMS output voltages are as high as 230 V. Wiring to
the speaker loads must conform to NEC Class 3 safety standards or its equivalent that meets all national and local electric codes.
All customer specific cables may only be manufactured by qualified
suppliers/personnel. All cabling or rewiring work must be carried out by
qualified personnel.
* Z
= 2 Ω for TECTON 28.2, 22.2 and 14.2
min
* Z
= 4 Ω for TECTON 38.4, 32.4 and 24.4
min
3.8.5 SPEAKON Connection
Both SPEAKON connectors are connected to channel A and channel B outputs.
The pin configuration of the SPEAKON connectors is as follows:
SPEAKON right: Pin 1+ Channel A signal
(View at the back) Pin 1- Channel A ground
Pin 2+ Channel B signal
Pin 2- Channel B ground
4 OPERATION
SPEAKON left: Pin 1+ Channel B signal
(View at the back) Pin 1- Channel B ground
Pin 2+ Channel A signal
Pin 2- Channel A ground
WARNING !
SPEAKON connectors marked with the lightning flash indicate high voltages that are potentially life threatening.
Wiring to these terminals requires installation by an instructed person or
the use of ready-made leads or cords.
Custom wiring should only be made by qualified personnel.
To prevent electric shock, do not operate the amplifier with any of the conductor portion of the speaker wire exposed.
P.16
Input
Channel A
Input
Channel B
USER MANUAL
TECTON POWER AMP SERIES
SPEAKON right
SPEAKON left
NOTE:
For reasons of safety and performance, use only high-quality fully insulated speaker cables of stranded copper wire. Use the largest wire size that
is economically and physically practical, and make sure the cables are no
longer than necessary.
IMPORTANT:
When connecting speaker cabinets in parallel, always use all the contacts
in both SPEAKON connectors. If not, this may cause permanent damage to
the connectors and considerably reduce performance.
4.1 Controls
4.1.1 Volume Control
A volume control with 41 notched settings controls the audio signal. These
settings have been selected to correspond to human hearing characteristics
(logarithmically) and therefore guarantee an optimal range of settings for practical applications. Each channel can be set individually except when operating
in mono modes whereby only channel A is active.
4 OPERATION
Set the volume to zero before turning on the amplifier to prevent the occurrence of sudden high volume levels which may cause damage to your hearing
and/or the speakers.
4.1.2 Gain Selector
A switch on the rear of the TECTON allows the maximum amplification attainable to be set directly in the input stage.
The TECTON amplifier has a 26 dB and 32 dB
voltage gain setting along with a 1,4 V sensitivity
setting.
4.1.3 Gain and Input Sensitivity
The table shows input sensitivity per channel for a given gain and load. It also
shows the gain for the 1,4 V input sensitivity.
Model 26 dB 32 dB 1,4 V
TECTON 38.4 1900 W @ 4 Ω
1100 W @ 8
TECTON 32.4 1600 W @ 4 Ω
915 W @ 8
TECTON 24.4 1200 W @ 4 Ω
700 W @ 8 Ω
TECTON 28.2 1420 W @ 2 Ω
920 W @ 4 Ω
TECTON 22.2 1140 W @ 2 Ω
660 W @ 4 Ω
TECTON 14.2 730 W @ 2 Ω
420 W @ 4 Ω
4.1.4 Limiter Switch
This switch is located at the rear of TECTON. It allows you to set the mode of the
limiter. There are three modes. (See 4.3.1 Clip Limiter)
Right position: Middle position: Left position:
Clip Limiter: Fast Clip Limiter: Slow Clip Limiter: Off
Attack fast Attack slow
4,37 V
Ω
4,70 V
4,01 V
Ω
4,29 V
3,47 V
3,75 V
2,67 V
3,04 V
2,39 V
2,58 V
1,92 V
2,05 V
2,19 V
2,36 V
2,01 V
2,15 V 35,72 dB
1,74 V
1,88 V 34,56 dB
1,34 V
1,52 V 32,74 dB
1,20 V
1,29 V 31,29 dB
0,96 V
1,03 V
36,52 dB
29,33 dB
P.17
USER MANUAL
TECTON POWER AMP SERIES
4.1.5 HPF Filter
(Channel A as example)
Left position: Middle position: Right position:
4 OPERATION
HPF: Off HPF: 30 Hz HPF: 50 Hz
HPF OFF
HPF 30 Hz
4.2 Indicators
4.2.1 Output Current LEDs
The brightness is proportional to the output current in the channel. Output
current of approx. 1 A lights up the LED at its lowest brightness level, while full
brightness corresponds to the maximum rated current.
P.18
USER MANUAL
TECTON POWER AMP SERIES
HPF 50 Hz
Low frequency response curves
4.2.2 Signal LEDs (multifunctional)
The channels Signal LED is illuminated green when the voltage level at the
output reaches approx. 4 V; this corresponds to a power of approx. 4 W at an
impedance of 4 Ohms. The channels Signal LED is illuminated red while the Amp
is in Protect Mode (Mute).
4.2.3 Clip LEDs
If the power level is overloaded, the Clip LED will light up.
4 OPERATION
4.3 Power Amp Protection Systems
4.3.1 Clip Limiter
If the power amp is overdriven, the clip detection triggers the Attack-ReleaseCircuit (ARC). The ARC delivers the control voltage for the gain reduction. Two
different attack modes (fast and slow) could be chosen with the Clip Limiter
switch (see 4.1.4 Limiter Switch).
4.3.2 SOA Protection
Whenever the power transistors leave their Safe Operation Area (SOA), the
SOA-protection in stereo mode switches back the current rail of the respective
channel. In mono modes the rails of both channels are switched back.
4.3.3 DC Protection
Each output of the power amp is constantly monitored for persistent DC voltage
levels. If the 3 V thresholds are exceeded at any of the outputs, the corresponding channel will be muted. If DC was only applied for a short moment, the amplifier will release mute and work as normal. If DC is applied for longer periods or
several short times the amplifier will switch to standby mode.
Switch off the amplifier, wait until the power LED stops flashing and switch the
amplifier on again.
4.3.4 DC Servo
To prevent DC Offset at the speaker output the TECTON is fitted with a DC
Servo.
4.3.5 Over Current Protection
Over current is permanently controlled in the output stage. There are two limiting levels of over current depending on output voltage. These limits will be set
automatically. This improves reliability without degrading sound quality when
driving complex loads.
4.3.6 Thermal Protection
There are several sensors in the amp in order to ascertain temperature data. If
a temperature of more than 85 °C is detected at the heat sinks, the input signal
on that channel is reduced. If the temperature exceeds 100 °C, the main SMPS
is switched off.
P.19
USER MANUAL
TECTON POWER AMP SERIES
4.4 Mains Protections
4.4.1 Inrush Current Limitation
Within 2 seconds of the amplifier being switched on, the inrush current limiter
will increase mains current from nearly zero to nominal value. This value depends
on program material, output level and speaker loads.
4.4.2 Mains Over Voltage Detection
Mains over voltage detection is always operative. When the mains voltage
4 OPERATION
exceeds approx. 267 V (230 V operation) or 134 V (120 V operation), the ampli
fier will be switched off. The system will try to start in intervals and will return
with a soft start when the regular mains voltage returns.
4.4.3 Mains Failure Detection
Mains failure detection is always operative. When the mains supply is interrupted for about 2 mains cycles, the amplifier will be switched off. When the
mains voltage returns to a normal value, a soft start occurs.
4.4.4 Fuse Protection
The average mains current can peak temporarily, depending on the load impedance and type of signal, at values significant higher than the nominal value
allowed by the fuse protection.
Continuous monitoring of the fuse protection status allows the conditions that
would trigger the fuse protection to be predicted. In order to avoid shut-down
of the amplifier due to current overload, the amplitude of the input signals will
be limited and by hard overloads the amp will be muted for the time.
4.5 Main SMPS Protections
4.5.1 Over Current Protection
Main SMPS (Switched Mode Power Supply) transformer current is continuously
monitored. If over current occurs, the main SMPS immediately stops working.
Should there be an internal failure, this feature prevents other parts being
damaged.
-
4.6 Fan
The fan mounted in the TECTON operates permanently, but as long as the
temperature remains below 40 °C it runs at its slowest speed and can hardly
be heard. The highest detected temperature from either channel controls the
speed of the fan: above 40 °C the speed is increased until it reaches its maximum
value.
P.20
USER MANUAL
TECTON POWER AMP SERIES
5.1 E.U.I.2 (Extended User Interface)
CAUTION! Always switch off and unplug the TECTON from mains, before
making alterations to the E.U.I. card.
The E.U.I. card contains the Rear XLR Panel as standard. Other input cards are
available (See 5.1.1 What Are The Possibilities Using The E.U.I.2?).
5 OPTIONS
To remove the E.U.I.2 unscrew the two Phillips head screws at the left and right
end of the XLR-Panel and carefully slide out the E.U.I.2.
To refit the E.U.I.2, carefully insert it. Pay attention that the cable is not clamped.
ATTENTION! Don’t forget to tighten the screws!
5.1.1 What Are The Possibilities Using The E.U.I.2?
The E.U.I.2 is a very powerful interface, which allows access to most of the
system parameters, such as volume, input signal, mute, output current, clip
signal, temperature and more. You can use the E.U.I.2 as a filter, remote control,
signal processing device and more… Please contact your dealer/distributor or
CAMCO to customise the E.U.I.2 according to your wishes.
P.21
USER MANUAL
TECTON POWER AMP SERIES
6.1 Problem: No Sound
Indication:
Indication:
6 TROUBLESHOOTING
Indication:
Indication:
6.2 Problem: No Channel Separation
Signal LEDs not lit
Clip LEDs not lit
Check AC plug.
Confirm that AC outlet works by plugging in another device.
Output Current LEDs are lit
Signal LEDs not lit
Make sure the signal source is operating and try another cable.
Check position of volume pots.
Output Current LEDs are lit
Signal LEDs responding to signal level
Check the speaker wiring for breaks.
Try another speaker and cable.
Signal LEDs show red (Protect Mode)
Overheating will cause protective muting. Check for proper ventilation.
If the fan isn’t running the amplifier requires servicing.
Check the mode indicators on the front panel and make sure the mode
selector on the rear panel is in the stereo-position.
Make sure other equipment in the signal path such as mixers and preamps
are set for stereo, not mono.
6.3 Problem: Distorted Sound
Indication:
Output Current LEDs are lit
Signal LEDs responding to signal level
Clip LEDs not lit
A faulty speaker or a loose connection could cause this. Check the wiring
and try another speaker.
The signal source might be clipping. Keep the TECTON volume pots at
least halfway up so that the source does not have to be overdriven.
Keep the TECTON volume pots at least halfway up and try changing input
sensitivity from 1,4 V to 32 dB or 26 dB with the gain selector on the rear.
6.4 Problem: Hiss
Unplug the amplifier input to confirm that the hiss is coming from the
source or from a device upstream. Erratic or popping noises indicate an
electronic fault in the offending unit.
To keep the noise floor low, operate the primary signal source at full level,
without clipping.
Avoid boosting the signal further between the source and the amplifier.
6.5 Problem: Squeals and Feedback
Microphone feedback should be eliminated with mixer controls. If noise
continues to build up with no microphone gain, there is a serious fault
in the signal processors or cables. Working in succession from the signal
source towards the amplifier and check each device in the signal path by
reducing its gain or by unplugging it.
P.22
USER MANUAL
TECTON POWER AMP SERIES
TECTON 38.4
Output Power
1 kHz, THD ≤ 1 %, in mono-bridge mode
1 x 3800 W @ 8
1 x 2200 W @ 16
1 kHz, THD
Duration limited by fuse / thermal protection for RL < 8 Ω
≤ 1 %, both channels driven
in stereo mode or RL < 16 Ω in mono-bridge mode.
2 x 1900 W @ 4
2 x 1100 W @ 8
1 kHz, THD < 0,1 %, both channels driven 2 x 1800 W
7 SPECIFICATION
2 x 1070 W @ 8
Circuitry Bipolar, Class H 2-step
high efficiency circuit
Signal to Noise-Ratio
20 Hz - 20 kHz, 8 Ω load, unweighted
A-
Power Consumption @ 230 V
(both channels driven)
weighted
>112 dB
>116 dB
Typical1)Max
Idle 1,4 A
60 W
16
Ω 4,8 A
410 W
8 Ω 7,3 A
700 W
4 Ω 11,3 A
1220 W
Multiply currents by 2 for 120 V
2)
1)
1/8 of max Output Power with pink noise to represent typical music signal
max. rated Output Power (see above)
@ 4 Ω
Ω
Ω
Ω
Ω
Ω
14,8 A
1600 W
25 A
3000 W
40 A
5230 W
1 x 3200 W @ 8
1 x 1800 W @ 16
2 x 1600 W @ 4
2 x 915 W @ 8
2 x 1500 W @ 4
2 x 860 W @ 8 Ω
Bipolar, Class H 2-step
high efficiency circuit
2)
Idle 1,3 A
16 Ω 3,9 A
8 Ω 6,2 A
4 Ω
TECTON 32.4
>111 dB
>115 dB
Typical1)Max
55 W
330 W
580 W
9,8 A
1010 W
Ω
Ω
Ω
Ω
Ω
12,2 A
1280 W
21 A
2410 W
34 A
4300 W
1 x 2400 W @ 8
1 x 1400 W @ 16
2 x 1600 W @ 2,7
2 x 1200 W @ 4
2 x 1135 W @ 4
Bipolar, Class H 2-step
high efficiency circuit
2)
Idle 1,2 A
16
Ω 3,9 A
8 Ω 5,2 A
4 Ω 7,9 A
2,7 Ω 10,5 A
TECTON 24.4
2 x 700 W @ 8 Ω
2 x 655 W @ 8 Ω
>110 dB
>115 dB
Typical1)Max
50 W
250 W
460 W
790 W
1060 W
Ω
Ω
Ω
Ω
Ω
2)
9,9 A
1000 W
16,5 A
1840 W
27 A
3230 W
36 A
4600 W
P.23
USER MANUAL
TECTON POWER AMP SERIES
TECTON 28.2
Output Power
1 kHz, THD ≤ 1 %, in mono-bridge mode
1 x 2800 W @ 4
1 x 1820 W @ 8
1 kHz, THD
Duration limited by fuse / thermal protection for RL < 8 Ω
≤ 1 %, both channels driven
in stereo mode or RL < 16 Ω in mono-bridge mode.
2 x 1400 W @ 2 Ω
2 x 910 W @ 4
1 kHz, THD < 0,1 %, both channels driven 2 x 1310 W @ 2
2 x 860 W @ 4 Ω
7 SPECIFICATION
Circuitry Bipolar, Class H 2-step
high efficiency circuit
Signal to Noise-Ratio
20 Hz - 20 kHz, 8 Ω load, unweighted
A-weighted
Power Consumption @ 230 V
(both channels driven)
>108 dB
>113 dB
Typical1)Max
Idle 1,2 A
45 W
8 Ω 4,2 A
360 W
4 Ω 6,5 A
611 W
2 Ω 9,5 A
1002 W
Multiply currents by 2 for 120 V
2)
1)
1/8 of max Output Power with pink noise to represent typical music signal
max. rated Output Power (see above)
Ω
Ω
Ω
Ω
13,1 A
1380 W
21 A
2490 W
33 A
4220 W
1 x 2200 W @ 4
1 x 1320 W @ 8
2 x 1100 W @ 2
2 x 660 W @ 4 Ω
2 x 1040 W @ 2
2 x 620 W @ 4 Ω
Bipolar, Class AB
high efficiency circuit
2)
Idle 1,4 A
8 Ω 4,3 A
4 Ω 6,8 A
2 Ω 10,6 A
TECTON 22.2
>105 dB
>111 dB
Typical1)Max
60 W
370 W
640 W
1120 W
Ω
Ω
Ω
Ω
10,1 A
1020 W
16,8 A
1870 W
27 A
3320 W
1 x 1340 W @ 4
high efficiency circuit
2)
Idle 1,2 A
8 Ω 3,3 A
4 Ω 4,7 A
2 Ω 7,4 A
TECTON 14.2
1 x 800 W @ 8
2 x 670 W @ 2 Ω
2 x 400W @ 4 Ω
2 x 610 W @ 2
2 x 380 W @ 4 Ω
Bipolar, Class AB
>98 dB
>108 dB
Typical1)Max
50 W
250 W
420 W
712 W
Ω
Ω
Ω
2)
6,8 A
660 W
10,9 A
1180 W
17,3 A
2130 W
P.24
USER MANUAL
TECTON POWER AMP SERIES
Frequency Response 20 Hz - 20 kHz ± 0,15 dB
8 Ω load, 10 dB below rated power
Input Impedance 14 kΩ balanced
Voltage Gain selectable: 26 dB, 32 dB, or 1,4 V input sensitivity
Protection Circuits inrush-current limitation, temperature monitoring of transformer and heat-sinks,
output DC protection, power transistor SOA protection, output over current protection,
mains fuses protection
Limiter switchable clip limiter
Fan temperature dependent speed-controlled axial fan
Ground Lift input ground lift switch on back panel
7 SPECIFICATION
Indicators LEDs for Mode, Signal, Clip, Output Current and faults for example like DC
Input Connectors 3-pin XLR, male and female per channel, pin 2 = inphase (hot)
Output Connectors one 4-pole SPEAKON connector for each output channel (bi-amping possible)
Modes of Operation Stereo, Mono-Bridge and Parallel-Mono
Options Extended User Interface / E.U.I. 2 – modules for any kind of EQ
THD+N (typical) < 0,01 %
20 Hz - 10 kHz, 8 Ω load,
10 dB below rated power
SMPTE (typical) < 0,01 %
8 Ω load,
10 dB below rated power
Damping Factor > 400
8 Ω load, 1 kHz and below
Dimensions (WxHxD) 483 x 88,9 x 330,7 mm (19”, 2U)
Net Weight 9,4 kg
Shipping Dimensions ( WxHxD) 540 x 135 x 540 mm (0,04 m3)
Shipping Weight 11 kg
Subject to technical alterations without prior notice
P.25
USER MANUAL
TECTON POWER AMP SERIES
8 MEASUREMENTS
P.26
+27
+26.5
+26
+25.5
+25
+24.5
+24
dBr
+23.5
+23
+22.5
+22
+21.5
+21
10 100k20 50 100 200 500 1k 2k 5k 10k 20k 50k
+26
+24
+22
+20
+18
+16
dBr
+14
+12
+10
+8
+6
+4
+2
-0
10 20k20 50 100 200 500 1k 2k 5k 10k
Gain vs. frequency / Different positions of HPF-Switch (Ch1, Ch2)
USER MANUAL
TECTON POWER AMP SERIES
Hz
Figure 8.1
Gain vs. frequency (Ch1, Ch2)
(Measurements of a typical performance)
Hz
Figure 8.2
(Measurements of a typical performance)
+180
+135
+90
+45
+0
deg
-45
-90
-135
-180
10 100k20 50 100 200 500 1k 2k 5k 10k 20k 50k
Hz
Figure 8.3
Phase vs. frequency (Ch1, Ch2)
(Measurements of a typical performance)
+180
+135
+90
+45
deg
+0
-45
-90
-135
-180
10 20k20 50 100 200 500 1k 2k 5k 10k
Hz
Figure 8.4
Phase vs. frequency / Different positions of HPF-Switch (Ch1, Ch2)
(Measurements of a typical performance)
8 MEASUREMENTS
P.27
300m
200m
100m
50m
Ohm
20m
10m
5m
2m
20 20k50 100 200 500 1k 2k 5k 10k
Figure 8.5 Output impedance vs. frequency
@ 1 Amp RMS injected current (Ch1,
(Measurements of a typical performance of TECTON 32.4)
-20
-30
-40
-50
-60
dB
-70
-80
-90
-100
-110
-120
100u 5200u 500u 1m 2m 5m 10 m 20m 50m 100m200m 500m 1 2
THD+N @ 1 kHz, 8 Ω load vs. input voltage (Ch1, Ch2)
(Measurements of a typical performance of TECTON 32.4)
USER MANUAL
TECTON POWER AMP SERIES
Hz
Ch2) equivalent 11 mΩ + 2,1 µH
Vrms
Figure 8.6
1000
800
r
o
600
t
c
a
f
g
n
i
p
m
400
a
d
200
0
20 20k50 100 200 500 1k 2k 5k 10k
Hz
Figure 8.7 Damping factor into 8 Ω (Ch1, Ch2)
equation: damping factor = loaded impedance / amplifier output impedance
(Measurements of a typical performance of TECTON 32.4)
-20
-30
-40
-50
-60
-70
dB
-80
-90
-100
-110
-120
20 10k50 100 200 500 1k 2k 5k
Hz
Figure 8.8
THD+N vs. frequency (BW 22 kHz), 10 dB below clip, 8 Ω (Ch1, Ch2)
(Measurements of a typical performance of TECTON 32.4)
8 MEASUREMENTS
P.28
-20
-30
-40
-50
-60
dB
-70
-80
-90
-100
-110
-120
100u 5200u 500u 1m 2m 5m 10m 20m 50m 100m200m 500m 1 2
Vrms
Figure 8.9
CCIF difference frequency method (10,5 kHz and 11,5 kHz) vs. input level
@ 8 Ω (Ch1, Ch2) (Measurements of a typical performance of TECTON 32.4)
-20
-30
-40
-50
-60
dB
-70
-80
-90
-100
100u 4200u 500u 1m 2m 5m 10m 20m 50m 100m 200m 500m 1 2
Vrms
Figure 8.10
SMPTE intermodulation distortion (60 Hz and 7 kHz) @ 8 Ω vs. input level
(Ch1,
USER MANUAL
TECTON POWER AMP SERIES
Ch2) (Measurements of a typical performance of TECTON 32.4)
-20
-30
-40
-50
dBr
-60
-70
-80
-90
-100
20 20k50 100 200 500 1k 2k 5k 10k
Hz
Figure 8.11
Common mode rejection ratio (Ch1, Ch2)
(Measurements of a typical performance of TECTON 32.4)
-10
-20
-30
-40
-50
dB
-60
-70
-80
-90
-100
-110
20 20k50 100 200 500 1k 2k 5k 10k
Hz
Figure 8.12
Channel separation vs. frequency @ 10 W / 8 Ω (Ch1 => Ch2, Ch2 => Ch1)
(Measurements of a typical performance of TECTON 32.4)
8 MEASUREMENTS
P.29
2500
2000
1500
Watts
1000
500
0
TECTON 38.4 (Measurements of a typical performance)
2000
1500
Watts
1000
500
0
TECTON 32.4 (Measurements of a typical performance)
USER MANUAL
TECTON POWER AMP SERIES
4
4
1900
1600
2275
Impedance/ Ω
1800
Impedance/ Ω
1122
8
915
8
1225
Figure 8.13
960
Figure 8.14
16
483
16
608
630
Distortion limited
output power (1 % THD)
500
Distortion limited
output power (1 % THD)
Peak power
Peak power
Watts
Watts
1500
1500
1000
1000
1365
1212
730
695
16
370
378
Distortion limited
output power (1 % THD)
Peak power
500
0
4
Impedance/ Ω
8
Figure 8.15
TECTON 24.4 (Measurements of a typical performance)
1440
1420
1008
920
534
500
0
2
Impedance/ Ω
4
515
8
Peak power
Distortion limited
output power (1 % THD)
Figure 8.16
TECTON 28.2 (Measurements of a typical performance)
1500
1220
1133
1000
Watts
500
700
670
370
362
Peak power
8 MEASUREMENTS
0
2
Impedance/ Ω
4
8
Distortion limited
output power (1 % THD)
Figure 8.17
TECTON 22.2 (Measurements of a typical performance)
P.30
1000
750
Watts
500
250
0
TECTON 14.2 (Measurements of a typical performance)
USER MANUAL
TECTON POWER AMP SERIES
2
700
756
Impedance/ Ω
417
4
435
Figure 8.18
230
8
233
Distortion limited
output power (1 % THD)
Peak power
9.1 Summary Of Warranty
CAMCO guarantees the TECTON amplifier to be free from defective material
and/or workmanship for a period of six (6) years from the date of sale. Provided
that the amplifier is returned to your dealer/distributor in a factory pack with
a copy of the proof of purchase, i.e., sales receipt, CAMCO will repair faulty products under this warranty when a defect occurs under normal installation and
use.
This warranty provides that examination of the returned product must indicate,
in our judgment, a manufacturing defect.
9.2 Items Excluded From This Warranty
CAMCO is not liable for any damage caused by shipping accidents, misuse,
abuse, operation with incorrect AC voltage, operation with faulty periphal
equipment, modification, or alteration without prior factory approval, service by
an unauthorised service center, and normal wear and tear. Amplifiers on which
9 WARRANTY INFORMATION
the Serial Number has been removed or defaced are not eligible for warranty
service.
9.3 What CAMCO Will Do
CAMCO (or its appointed agent) undertakes to rectify any defect, regardless of
the reason for failure (unless excluded from this warrenty), by repair, replacement, or refund, as it sees fit.
9.4 How To Obtain Warranty Service
You must notify your dealer/distributor of your need for warranty service.
All components must be shipped in the original packing.
9.5 CAMCO’s Product Improvement
CAMCO reserves the right to improve the technical standard of its products
without giving prior notice. If in any doubt, please consult your dealer/distri-
butor or contact CAMCO directly for clarification.
P.31
USER MANUAL
TECTON POWER AMP SERIES
PLEASE ENCLOSE THIS COMPLETED FORM WITH THE AMPLIFIER
DO NOT SEND SEPARATELY
10 SERVICE INFORMATION
P.32
Owner’s Information
Company Name: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Contact: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Address: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Telephone: _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Facsimile: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
eMail Address: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Model: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Serial Number: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Purchase Date: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Expired Warranty
If the warranty has expired, payment will be:
Cash/Cheque
VISA
MasterCard
Shipping Address
To transport the amplifier, the original packing materials must be used. Please
return the amplifier to the following address or your nearest CAMCO appointed
distributor.
CAMCO Produktions- und Vertriebs- GmbH für Beschallungs- und Beleuchtungsanlagen, Fischpicke 5, D-57482 Wenden, Germany
USER MANUAL
TECTON POWER AMP SERIES
Nature Of Problem
Please describe the conditions that existed when the problem occured and what
attempts were made to correct it: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Other equipment in your system: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
_ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
Our web site: www.camcoaudio.com provides a complete list of CAMCO
dealers/distributors.
11 Maintenance Information
Cleaning and servicing the inside of the amplifier must never carry out by unqualified personnel. The amplifier must never be opened by unqualified personnel.
Cleaning and servicing work on the inside of the amplifier must only be carried
out by qualified personnel.
Qualified personnel is defined as a person who has gained specialised relevant
knowledge of electronic engineering through education, training and experience and who has sufficient knowledge of all relevant governmental work
safety regulations to be in a position to judge the safe functioning of power
amplifiers based on technical rules according to IEC 60065.
(IEC 60065 (DIN EN 60065) “Safety Requirements for Audio, Video or simlar
Electronic Appliances”)
In order to guarantee the safe functioning of the amplifier, it has to be checked
at least once, depending on its application and usage, by a properly qualified
person.
Advice on how to carry out these checks can be found in DIN VDE 0702-1 “Safety
Checks for Electronic Appliances”.
An amplifier that is considered to be unsafe must be labelled accordingly and
stored in a safe place to prevent this amplifier being used mistakenly.
12 Decomissioning
During the decomissioning process of the amplifier, all legally prescribed rules
and procedures must be adhered to.
11 MAINTENANCE INFORMATION/12 DECOMISSIONING
USER MANUAL
TECTON POWER AMP SERIES
P.33
Mailing Address:
CAMCO Produktions- und Vertriebs- GmbH
für Beschallungs- und Beleuchtungsanlagen
Fischpicke 5
D-57482 Wenden
Germany
Telephone:
+49 (0) 27 62/4 08- 0
Facsimile:
+49 (0) 27 62/4 08- 10
Internet:
www.camcoaudio.com
COMPANY INFORMATION
Email:
postmaster@camcoaudio.com
P.34
USER MANUAL
TECTON POWER AMP SERIES
www.camcoaudio.com
Loading...