Cambridge Audio Evo 150, Evo 75 User Manual
Evo 75
Evo
ALL IN ONE PLAYER
150
Contents
IMPORTANT SAFETY INSTRUCTIONS 3
REAR PANEL CONNECTIONS 6
FRONT PANEL CONTROLS 7
REMOTE CONTROL 8
REPLACEABLE SIDE PANELLING 8
OVERVIEW 9
GETTING CONNECTED 9
ADVANCED USB AUDIO 10
BALANCED AUDIO CONNECTIONS EVO 150 ONLY 10
USB AUDIO CONNECTION EVO 150 ONLY 10
GETTING CONNECTED 11
OPERATING INSTRUCTIONS 12
PRESETS 12
HOW TO USE RADIO 12
MUSIC LIBRARY 12
USB MEDIA 13
INPUTS 13
BLUETOOTH AUDIO STREAMING 13
SPOTIFY 13
AIRPLAY 13
CHROMECAST BUILTIN 13
SETTINGS 14
SETUP WIFI 14
ENTER THE NETWORK NAME 14
UPDATE FIRMWARE 15
AUDIO 15
USB AUDIO CLASS 15
AUDIO OUTPUT 15
BLUETOOTH AUDIO OUTPUT 15
STANDBY MODE 15
NETWORK STANDBY ON 15
AUTOMATIC POWER DOWN 15
LANGUAGE 16
DISPLAY BRIGHTNESS 16
FACTORY RESET 16
STREAMMAGIC APP 16
TECHNICAL SPECIFICATIONS 17
TROUBLESHOOTING 18
This guide is designed to make installing and using this product as easy
as possible. Information in this document has been carefully checked
for accuracy at the time of printing; however, Cambridge Audio’s policy
is one of continuous improvement, therefore design and specications
are subject to change without prior notice.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by
any mechanical, electronic or other means, in any form, without prior
written permission of the manufacturer. All trademarks and registered
trademarks are the property of their respective owners.
The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by Audio
Partnership Plc is under license. Other trademarks and trade names are
those of their respective owners.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the
United States and other countries, used with permission.
aptX is a trademark of Qualcomm Technologies International,
Ltd., registered in the United States and other countries, used with
permission. Qualcomm aptX is a product of Qualcomm Technologies
International, Ltd
Stream Magic is a trademark of Audio Partnership Plc and is registered
in the European Community and other countries.
This product contains software licensed under version 2 of the GNU
Public License and version 2.1 of the GNU Lesser Public License. The
source code for this software is available from:
http://gpl.stream-magic.com/
This product includes technology owned by Microsoft Corporation and
under a licence from Microsoft Licensing GP. Use or distribution of such
technology outside of this product is prohibited without a license from
Microsoft Corporation and/or Microsoft Licensing, GP as applicable.
The Spotify software is subject to third party licenses found here:
www.spotify.com/connect/third-party-licenses.
This Evo 75/Evo 150 support AirPlay 2 and requires iOS 11.4 or later.
Apple and AirPlay are trademarks of Apple Inc., registered in the U.S.
and other countries.
Use of the Works with Apple badge means that an accessory has
been designed to work specically with the technology identied
in the badge and has been certied by the developer to meet Apple
performance standards.
Android, Google Play and the Chromecast built-in logo are trademarks
of Google Inc.
TIDAL and TIDAL logo are registered trademark of Aspiro AB in the
European Union and other countries.
© Copyright Cambridge Audio Ltd 2020.
Make sure you register your CA product:
WWW.CAMBRIDGEAUDIO.COM/REGISTER
For upcoming news on future products, software updates and exclusive
oers.
Support
If you have questions about your Cambridge Audio product visit
https://support.cambridgeaudio.com where you will nd FAQs and
guides to assist you.
2
Important safety instructions
For your own safety please read the following important safety instructions
carefully before attempting to connect this unit to the mains power supply.
They will also enable you to get the best performance from and prolong the
life of the unit:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly
at plugs, convenience receptacles and the point where they exit from
the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use with only the cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as the powersupply cord or plug having been damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
WARNING:
– Do not place the unit in an enclosed space; if you wish to place the unit on
a shelf, use the top shelf to allow maximum ventilation. Do not put any
objects on top of this unit. Do not situate it on a rug or other soft surface
and do not obstruct any air inlets or outlet grilles. Do not cover the
ventilation grilles with items such as newspapers, tablecloths, curtains,
etc.
– To reduce the risk of re or electric shock, do not expose this apparatus
to rain or moisture . This unit must not be used near water or exposed to
dripping or splashing water or other liquids. No objects lled with liquid,
such as vases, shall be placed on the unit.
– Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type.
– The battery (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, re or the like.
– The unit must be installed in a manner that makes disconnection of
the mains plug from the mains socket outlet (or appliance connector
from the rear of the unit) possible. Where the mains plug is used as the
disconnect device, the disconnect device shall remain readily operable.
– Please refer to the information on the exterior rear panel for electrical
and safety information before installing or operating the apparatus.
– Only use the mains cord supplied with this unit.
Use of the apparatus in tropical climates - The equipment shall be used at
a maximum 45 degree C ambient temperature.
The unit is of Class 1 construction and must be connected to a mains
socket outlet with a protective earthing connection.
The lightning ash with the arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of un-insulated
‘dangerous voltage’ within the product’s enclosure that may be of
sucient magnitude to constitute a risk of electric shock to persons.
Warning: To reduce the risk of electric shock, do not remove cover (or
back) as there are no user-serviceable parts inside. Refer servicing to
qualied personnel. The exclamation point within an equilateral triangle
is intended to alert the user to the presence of important operating
and maintenance instructions in the service literature relevant to this
appliance
VENTILATION
Important! The unit will become hot when in use. Do not stack multiple
units on top of each other.
Ensure that small objects do not fall through any ventilation grille. If this
happens, switch o immediately, disconnect from the mains supply and
contact your dealer for advice.
POSITIONING
Choose the installation location carefully. Avoid placing it in direct
sunlight or close to a source of heat. No naked ame sources, such as
lighted candles, should be placed on the unit. Also avoid locations subject
to vibration and excessive dust, cold or moisture. The unit can be used in
a moderate climate.
This unit must be installed on a sturdy, level surface. Do not place in a
sealed area such as a bookcase or in a cabinet. Do not place the unit on
an unstable surface or shelf. The unit may fall, causing serious injury to a
child or adult as well as serious damage to the product. Do not place other
equipment on top of the unit.
Due to stray magnetic elds, turntables or CRT TVs
should not be located nearby due to possible interference.
Electronic audio components have a running in period of around a week (if
used several hours per day). This will allow the new components to settle
down and the sonic properties will improve over this time
POWER SOURCES
The unit should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power-supply to
your home, consult your product dealer or local power company. If you do
not intend to use this unit for a long period of time, unplug it from the
mains socket.
OVERLOADING
Do not overload wall outlets or extension cords as this can result in a risk
of re or electric shock. Overloaded AC outlets, extension cords, frayed
power cords, damaged or cracked wire insulation and broken plugs are
dangerous. They may result in a shock or re hazard.
Be sure to insert each power cord securely. To prevent hum and noise, do
not bundle the interconnect leads with the power cord or speaker leads.
CLEANING
To clean the unit, wipe its case with a dry, lint-free cloth. Do not use any
cleaning uids containing alcohol, ammonia or abrasives. Do not spray an
aerosol at or near the unit.
SERVICING
These units are not user serviceable. Never attempt to repair, disassemble
or reconstruct the unit if there seems to be a problem. A serious electric
shock could result if this precautionary measure is ignored. In the event of
a problem or failure, please contact your dealer.
/
3
3
Wi-Fi information
BATTERY DISPOSAL
Batteries may contain substances harmful to the environment. Please
dispose of any discharged batteries with due consideration and in
accordance with local environmental/electronic recycling guidelines.
WEEE SYMBOL
The crossed-out wheeled bin is the European Union symbol
for indicating separate collection for electrical and electronic
equipment. This product contains electrical and electronic
and should not be disposed of with unsorted regular waste. Please return
the unit or contact the authorised dealer from whom you purchased this
product for more information.
equipment which should be reused, recycled or recovered
CE MARK
This product complies with European Low Voltage (2014/35/
Environmentally-friendly design of Energy-related Products (2009/125/
EC) Directives when used and installed according to this instruction
manual. For continued compliance only Cambridge Audio accessories
should be used with this product and servicing must be referred to
qualied service personnel.
ERAC and ACMA.
EU), Electromagnetic Compatibility (2014/30/EU) and
RCM (REGULATORY COMPLIANCE MARK)
This product meets Australia, New Zealand Safety,
EMC and Radio Communications requirements of the
FEDERAL COMMUNICATIONS COMMISSION
Supplier’s declaration of conformity (SDoC)
Equipment(s): All In One Player
Model(s): Evo 75, Evo 150
Trademark: Cambridge Audio
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The responsible party in US:
Company name: Audio Partnership LLC
Address: 1913 N Milwaukee Ave. Chicago, IL 60647
Phone: (312) 636-4817
Legal Representative Person: Gregg Chopper
Signature:
FEDERAL COMMUNICATIONS COMMISSION NOTICE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on,
the user is encouraged to try and correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
2.4 GHz Wi-Fi operation of this product in the USA is hardware limited to
channels 1 through 11.
5G channels are 36-48, 52-64, 100-140, 149-161.
FCC RADIATION EXPOSURE STATEMENT:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and
your body.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
MODIFICATIONS:
The FCC requires the user to be notied that any changes or
modications to this device that are not expressly approved by Cambridge
Audio, may void the user’s authority to operate the equipment.
4
Limited warranty
/
5
CANADA INDUSTRY CANADA IC
This radio transmitter has been approved by Industry Canada.
This device complies with Industry Canada License exempt RSS
standard(s). Operation is subject to the following two conditions.
(1) this device may not cause interference and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and your body.
The transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
INDUSTRIE CANADA IC
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement. Cet
équipement doit être installé et utilisé à une distance minimale de 20 cm
entre le radiateur et votre corps.
L’émetteur ne doit pas être co-placé ni fonctionner en conjonction avec
une autre antenne ou transmetteur.
EUROPEEUROPEAN UNION NOTICE
Hereby, Audio Partnership PLC declares that this product is in
compliance with Directive 2014/53/EU, the full text of the EU
declaration of conformity is available at the following internet address:
https://www.cambridgeaudio.com/DoC
WARNING: To reduce exposure to electromagnetic radiation, it is advised
that user is situated at least 20cm from the Wi-Fi Antenna during normal
operation.
FCC ID:YKBCA0999-038 IC:9095A-CA0999038
CAN ICES-3 (B)/NMB-3 (B)
Contains FCC ID:UAY-W8997-M1216 IC:6549A-W8997M1216
Bluetooth Radio frequency: 2.402GHz-2.48GHz, Max. transmit power:
10dBm.
EUROPE STANDARD:
Wi-Fi 2.4G Radio frequency: 2412-2472MHz, the Max. EIRP power 23dBm
Wi-Fi 5G Radio frequency: 5180-5825MHz, the Max. EIRP power 26dBm
Cambridge Audio warrants this product to be free from defects in materials
and workmanship (subject to the terms set forth below). Cambridge Audio
will repair or replace (at Cambridge Audio’s option) this product or any
defective parts in this product. Warranty periods may vary from country
to country. If in doubt consult your dealer and ensure that you retain proof
of purchase.
To obtain warranty service, please contact the Cambridge Audio authorised
dealer from which you purchased this product. If your dealer is not
equipped to perform the repair of your Cambridge Audio product, it can be
returned by your dealer to Cambridge Audio or an authorised Cambridge
Audio service agent. You will need to ship this product in either its original
packaging or packaging aording an equal degree of protection.
Proof of purchase in the form of a bill of sale or receipted invoice, which
is evidence that this product is within the warranty period, must be
presented to obtain warranty service.
This Warranty is invalid if (a) the factory-applied serial number has been
altered or removed from this product or (b) this product was not purchased
from a Cambridge Audio authorised dealer. You may call Cambridge
Audio or your local country Cambridge Audio distributor to conrm that
you have an unaltered serial number and/or you made a purchase from a
Cambridge Audio authorised dealer.
This Warranty does not cover cosmetic damage or damage due to acts of
God, accident, misuse, abuse, negligence, commercial use, or modication
of, or to any part of, the product. This Warranty does not cover damage due
to improper operation, maintenance or installation, or attempted repair
by anyone other than Cambridge Audio or a Cambridge Audio dealer,
or authorised service agent which is authorised to do Cambridge Audio
warranty work. Any unauthorised repairs will void this Warranty. This
Warranty does not cover products sold AS IS or WITH ALL FAULTS.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY
ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. CAMBRIDGE AUDIO
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND
IMPLIED WARRANTIES WHATSOEVER INCLUDING, BUT NOT LIMITED
TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PRACTICAL PURPOSE.
Some countries and US states do not allow the exclusion or limitation of
incidental or consequential damages or implied warranties so the above
exclusions may not apply to you. This Warranty gives you specic legal
rights, and you may have other statutory rights, which vary from state to
state or country to country.
For any service, in or out of warranty, please contact your dealer.
5
Rear panel connections
B
1
Max Power Consumption: 700W
Power AC
Power Rating:
100V-240V~50/60Hz
1
Max Power Consumption: 400W
Power AC
Power Rating:
100V-240V~50/60Hz
A
Right
Loudspeaker
Right
Loudspeaker
3
2
TV ARCCD USB Audio
Coax
In
4–8 Ω
3
2
TV ARCCD
Coax
In
4–8 Ω 4–8 Ω
Ground
Switch
1 2 3
Optical In XLR In Aux In MM Phono
1 2
Ground
Switch
1 2
Optical
In
6
54 8
USB Media
R L
7
Ethernet
Trigger
Out
1110 12
6
USB Media
7
Ethernet
Aux In
Sub-Out
Trigger In
Ground
Sub-Out
IR In
Pre-Out
13
8
IR In
Pre-Out
9
RS-232C
Serial no. fitted on underside
Left
Loudspeaker
B A
4–8 Ω
14
Left
Loudspeaker
Evo 150
Evo 75
1. AC POWER SOCKET
2. CD
allows for Evo CD using this control system and display from your Evo 75/
Evo 150
3. AUDIO RETURN CHANNEL ARC
Connec tion from a T V that supp orts ARC f unction
4. USB AUDIO IN EVO 150 ONLY
For connecting to PC/MAC computers.(Class 2 USB Audio only. windows
based PC's require a Cambridge Audio USB drive to be installed before
connection)
GROUND SWITCH
1: The Ground Switch enables the USB interface earth and main board
earth to be disconnected from the Evo 75/Evo 150 chassis earth.
2: Disconnecting (lifting) the earth can be useful if electronic hum is heard
through the speakers. the switch should otherwise be left in the Ground
position.
3: The Ground Switch enables the USB interface earth and main board
earth connected from the Evo 150 chassis earth. (Evo 150 only)
5. DIGITAL INPUTS COAX IN, OPTICAL IN1/IN2
Note: Optical in 2 is available on the Evo 150 only.
6. USB MEDIA
For connecting local media storage. Note that the USB ports are not
intended for connection to Apple mobile devices; no functionality,
charging or otherwise is supported.
7. ETHERNET
Ethernet port for connecting to a 10/100BASE-T local area network (LAN).
Your unit will automatically default to an Ethernet connection if one is
made.
8. TRIGGER IN/OUT EVO 150 ONLY
The Evo 150 can be connected to the trigger control output of home
12105
13
automation equipment to control the power state of the Evo 150. The input
level should be 12V. The trigger out will go high while the Evo 150 is powered
on. This can be used to turn on other equipment that has a trigger in.
IR In: Allows modulated IR commands from an IR repeater or custom
install systems to be received by the amplier.
14
9. RS232C
Custom install control - a full protocol is available for the Evo 150 on our
website.
10. ANALOGUE INPUTS XRL IN, AUX IN
Note: Blanced (XLR in) is available on the Evo 150 only.
the balanced connection is the higher quality option and can reject noise
and interference in the cable when used with other equipment that
supports this function. An XLR connector is wired Pin 1 - Ground; Pin 2 Hot (in-phase); Pin 3 - Cold (phase-inverted).
Aux in is suitable for any 'line level' source equipment such as CD players,
DAB or FM/AM tuners etc.
Note: These inputs are for analogue audio signals only. They should not be
connected to the digital output of a CD player or any other digital device.
11. MM PHONO INPUT EVO 150 ONLY
This input has a built in phono stage. Record players tted with Phono
Cartridges of the Moving Magnet (MM) , the "ground" terminals on both
the reocrder player and the Evo 150 should be connected(where possible)
with a ground wire for lowest noise/hum pickup.
12. SUB OUT
Connect to the input on an active subwoofer if required.
13. PREOUT
For connection to the unbalanced inputs of a power amplier or active
subwoofer.
14. LOUDSPEAKER TERMINALS
Important Note: When using a banana plug, make sure the speaker
terminals are completely tightened before inserting the plug.
B SPEAKER (Evo 150 ONLY)
6
Loading...