Cambium Networks X2120 User Manual
August 28, 2015
X2 and XR300 Series Notices
Notices and Regulatory Guide
is a registered trademark of Xirrus, Inc. All other trademarks and brand names are marks of their
respective holders.
All rights reserved. This document may not be reproduced or disclosed in whole or in part by any means without
the written consent of Xirrus, Inc.
Part Number: 812-0142-001 Rev D August 28, 2015
X2 and XR300 Series Notices and Regulatory Guide
X2 and XR300 Series Notices
This document contains the following information:
“Notices” on page 1
“EU Directive 1999/5/EC Compliance Information” on page 5
“Safety Warnings” on page 9
“Translated Safety Warnings” on page 10
“Software License and Product Warranty Agreement” on pa ge 11
“Hardware Warranty Agreement” on page 15
This document contains Notices, Warnings, Compliance and Legal information for the X2 and XR300
Series only. This includes the XR320 (marketed as XR-320) and the X2120 (marketed as X2-120).
For Notices, Warnings, and Compliance information for other indoor products, please see Appendices in the
Xirrus Wireless Access Point User’s Guide. For Notices, Warnings, and Compliance information for
outdoor products, please see the Quick Installation Guide for that product.
Notices
Wi-Fi Alliance Certification
www.wi-fi.org
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate RF energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following safety measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced wireless technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
!
could void the user's authority to operate this equipment.
1
X2 and XR300 Series Notices and Regulatory Guide
This device complies with Part 15 of the FCC Rules, with operation subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
For X2 Series products available in the USA/Canada market, only channels 1~11 can be operated. Selection of
other channels is not possible.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
This device is restricted for indoor use. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To ensure
compliance with FCC and Industry Canada RF exposure requirements, this device must be installed in a location
where the antennas of the device will have a minimum distance of at least 30 cm (12 inches) from all persons,
except that X2 models must have a minimum distance of at least 20 cm (8 inches) from all persons. Using higher
gain antennas and types of antennas not certified for use with this product is not allowed.
Non-Modification Statement
Unauthorized changes or modifications to the device are not permitted. Use only the supplied internal antenna, or
external antennas supplied by the manufacturer and approved for this device. Non-approved antennas may
produce unwanted spurious or excessive RF transmitting power which may be prohibited and violate regulatory
limits. Modifications to the device will void the warranty and may violate FCC regulations.
Cable Runs for Power over Ethernet (PoE)
If using PoE, the AP must be connected to PoE networks without r outing cabl ing to the outsid e plant—this ens ure s
that cabling is not exposed to lightning strikes or possible cross over from high voltage.
Battery Warning
Caution! The AP contains a battery which is not to be replaced by the customer. Danger of Explosion exists if
!
the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.
UL Statement
Use only with listed ITE product.
RF Radiation Hazard War ning
To ensure compliance with FCC RF exposure requirements, this device must be installed in a location where the
antennas of the device will have a minimum distance of at least 30 cm (12 inches) from all persons. Using higher
gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be
co-located with another transmitter.
Installation
This device is designed for a specific application and must be install ed by qualified personnel with knowledge of
RF and related rules. Please refer to the Quick Installation Guide for the product for installation instructions.
General users shall not attempt to install the device or change its settings.
2
X2 and XR300 Series Notices and Regulatory Guide
Warning: Please carefully select the installation location and ensure that the final output power does not
!
exceed local regulatory limits. The violation of this rule could lead to serious official penalties.
Industry Canada Statement (X2)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas pr oduir e de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels
is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection
d'autres canaux n'est pas possible.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with IC multi-transmitter product procedures.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou
transmetteur.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 56505725 MHz
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz
et 5650-5725 MHz
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LELAN devices.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs
principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient
causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
For indoor use only.
Pour une utilisation en intérieur uniquement.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator and your
body.
3
X2 and XR300 Series Notices and Regulatory Guide
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement and Marking (non-X2)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications
were met. This equipment should be installed and operated with a minimum distance of 30cm between the
radiator and your body.
Cet équipement doit être installé et utilisé à une distance minimale de 30cm entre le radiateur et votre corps.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un
type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
High Power Radars
High power radars are allocated as primary users (meaning they have priority) in the 5250MHz to 5350MHz and
5650MHz to 5850MHz bands. These radars could cause interference and/or damage to LELAN devices used in
Canada.
Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les
bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz. Ces radars pourraient causer du brouillage et/ou des dommages aux
dispositifs LAN-EL.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems;
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l'intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
4
Loading...