Cambium Networks cnPilot e501S Quick Start Manuals

Drill 4 holes of Ø6mm (Ø0.25”Inch) on wall. Press fit
plastic anchor and assembly fastener. Leave 5mm to
6mm gap between wall and fastener head.
Use the four mounting slots given on the back of the
radio to mount to the wall.

Introduction

This guide provides quick installation steps for cnPilot E501S
Access Points (APs).

Tool Requirements

• Phillips screwdriver (Wall Mounting)

• Flat head screwdriver (Pole Mounting)

• 12 mm wrench (Pole Mounting)

community.cambiumnetworks.com

JOIN THE CONVERSATION

Package Contents

Pole mounting bracket

PoE Injector

Cable gland

(Qty. 2)

E501S Access Point

Align Radio to required angle by tilting up and down.
The maximum radio tilting angle is ± 40°, with an
incremental of 10°.

Radio holder

Hose clamp

(Qty. 2)

Power Cord

Tools Required

Wall mounting kit

(Qty. 4)

M12 x 60 Bolt

M12 Nut & Washer

STEP 1 (Pole Mount)

Assemble the radio holder to the pole mounting bracket
and secure it with M8 nuts by applying 3.0 Nm torque.

STEP 2 (Pole Mount)

Insert hose clamps through pole mounting bracket and
clamp to pole by applying 3.0 Nm torque.

STEP 3 (Pole Mount)

Align the radio chassis with the guide rails of radio
holder and slide it downwards until it clicks into place.

Cable gland components

Components

Gland Assembly

Cable gland assembly sequence

Cap Plastic Seal Body

6. Assembled cable gland.5. Assemble cap and body.

4. Insert seal into body.

3. Insert seal into the plastic.2. Put seal over the cable.

1. Pass cable through cap.

STEP 4 STEP 5 (Pole Mount)

Insert RJ45 to radio housing and the lock cable gland to
radio housing with 1.5Nm to 2Nm torque.
For suggested Lightning Protection Deployment visit
http://bit.ly/cnPilot_Lightning

STEP 6 (Radio alignment)

Wall Mounting

802.11ac Outdoor WLAN Access Point with Integrated
90°/120° Antenna & IP67 Industrial Grade Gigabit WiFi

cnPilot™ e501S

90/120° Sector

108

100

Quick Start
Guide

Model: cnPilot e501S

Quick Link Setup

Configure Management PC

Hardware Overview

Hardware Overview

Powering Up

IC Statement

Online Resources

User Guide and software downloads:

https://support.cambiumnetworks.com/files/e501S/

Lightning Protection Deployment Diagram:

http://bit.ly/cnPilot_Lightning

Support:

http://www.cambiumnetworks.com/support/

Contact us:

http://www.cambiumnetworks.com/support/contact-support/

Using a web browser, navigate to 169.254.1.1 and login with

username: admin and password: admin

Navigate to the Quick Start menu and click the ‘Go To Next Page’.

Configure your Region and Country of operation. Click the ‘Go To

Next Page’.

Configure the Carrier Frequency. Click the ‘Go To Next Page’.

Select the Synchronization source. Click the ‘Go To Next Page’.

Configuration - IP Address, a Subnet Mask, and a Gateway IP

Address OR DHCP state to Enabled to have the IP address, subnet

mask, and gateway IP address automatically configured by a

DHCP server. Click the ‘Go To Next Page’.

Click the ‘Save Changes’ button. Click the ‘Reboot’ button.

1.

2.

3.

4.

5.

6.

7.

1.

2.

3.

Connect the Ethernet cable from Eth1/PoE-IN of E501S to the PoE

port of Gigabit Data + Power

Connect an Ethernet cable from your LAN or Computer to the

Gigabit Data port of the PoE adapter.

Connect the Power Cord to the adapter, and then plug the Power
Cord into a power outlet.

Once powered ON -- Power LED should illuminate continuously on

PoE Adapter.

**Shielded Category 5 (or above) cabling should be used for all
outdoor wired Ethernet connections and should be grounded
through the AC ground of the PoE.

RoHS/WEEE/CE Compliance

Caring for the Environment: RoHS/WEEE

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product

and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates

that this product should be disposed of separately from regular household waste streams. It is your

responsibility to dispose of this and other electric and electronic equipment via designated collection

facilities appointed by the government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human health. For more detailed

information about the disposal of your old equipment, please contact your local authorities, waste

disposal service, or the shop where you purchased the product.

CE Marking

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator

& your body.

All operational modes:

2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40)

5GHz: 802.11a, 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80)

The frequency, mode and the maximum transmitted power in EU are listed below:

2412-2472MHz (802.11n HT40 MCS0): 19.87 dBm

5500-5700MHz (802.11ac VHT80 MCS0/Nss1): 29.99 dBm

5745-5825 MHz (802.11ac (VHT20)-(ChS-20MHz): 35.76 dBm

Hereby, [Cambium Networks Inc.] declares that the radio equipment type [cnPilot OutdoorE501S] is

in compliance with Directive 2014/53/EU.

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other

channels is not possible.

Professional installation is required.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 25cm between the radiator &

your body.

Safety Notice

Warning:

To prevent loss of life or physical injury, observe the following safety guidelines. In no
event shall Cambium Networks be liable for any injury or damage caused during the
installation of E501S platform. Ensure that only qualified personnel install.

Only use attachments/accessories specified by the manufacturer.

Electrical Safety Information

Compliance with manufacturer’s label for voltage, frequency, and current
requirements. Connecting to a dierent power source than those specified may
result in improper operation, damage to equipment or pose a fire hazard if the
limitations are not followed.

There are no serviceable parts inside this equipment. Service should be
provided only by a qualified service technician.

This equipment is provided with a detachable power cord which has an integral
safety ground wire intended for connection to a grounded safety outlet.

Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire outlet
as this will defeat the continuity of the grounding wire.

The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can
result in serious injury or death.

Contact a qualified electrician or the manufacturer if there are questions
about the installation prior to connecting the equipment.

Protective earthing is provided by Listed AC adapter. Building installation
shall provide appropriate short-circuit backup protection.

Protective bonding must be installed in accordance with local national
wiring rules and regulations.

1.

2.

3.

a.

b.

c.

d.

e.

Select Properties for the Ethernet port. In Windows it is found in

Control Panel > Network and Internet > Network Connections > Local

Area Connection.

IP Address Configuration

Default IP address received via DHCP.

cn Pilot E501S will use a default static IP address of 192.168.0.1, If

there is no DHCP server

Default Login information

- Username: admin

- Password: admin

Management Protocols enabled by default –http or https (webpage

management interface access), SSH (CLI management interface access).

1.

2.

3.

Specifications

Secondary Port

The Secondary port is a Gigabit Ethernet port used for bridging.

Reset

The Reset button serves two functions for E501S:

- To restart, press and release the Reset button quickly.

- To restore to factory default settings, press and hold the

Reset button for more than 10 seconds.

Main Port

The Main port is a Gigabit Ethernet port used to connect the power and

should be connected to the LAN and DHCP server.

Main Port

Reset Button

Secondary Port

System LED

Network LED

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other

channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités.

Sélection d'autres canaux n'est pas possible.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 26 cm between the

radiator & your body.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement

non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 26 cm de distance entre la

source de rayonnement et votre corps.

*Regulatory dependent