Cabletron Systems 9E138-36b, 9E138-36, 9E132-15, 9E138-12 User Manual

SmartSwitch 9000

9E132-15, 9E133-36

9E138-12 & 9E138-36

User’s Guide

9031173-02

Notice

Notice

Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT,

SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED
TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION
CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR
SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

© Copyright April 1998 by:
Cabletron Systems, Inc.

35 Industrial Way
Rochester, NH 03867-5005

All Rights Reserved
Printed in the United States of America

Order Number: 9031173-02

LANVIEW
CompuServe

i960 microprocessor

Ethernet

is a registered trademark, and

is a registered trademark of CompuServe, Inc.

is a registered trademark of Intel Corp.

is a trademark of Xerox Corporation.

SmartSwitch

is a trademark of Cabletron Systems, Inc.

i

Notice

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

NOTE:

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial envir onment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.

WARNING:

party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital

Changes or modifications made to this device which are not expressly approved by the

VCCI Notice

This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.

DOC Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.

ii

Notice

DECLARATION OF CONFORMITY

ADDENDUM

Application of Council Directive(s):

89/336/EEC
73/23/EEC

Manufacturer’s Name: Cabletron Systems, Inc.

Manufacturer’ s Address: 35 Industrial Way

PO Box 5005
Rochester, NH 03867

European Representative Name: Mr. J. Solari

European Representative Address: Cabletron Systems Limited

Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards:

EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950

Equipment Type/Environment:

Networking Equipment, for use in a

Commercial or Light

Industrial Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with
this notice conforms to the above directives.

Manufacturer Legal Representative in Europe
Mr. Ronald Fotino Mr. J. Solari

____________________________________________________ ______________________________________________________

Full Name Full Name
Principal Compliance Engineer Managing Director - E.M.E.A.

____________________________________________________ ______________________________________________________

Title Title
Rochester, NH, USA Newbury, Berkshire, England

____________________________________________________ ______________________________________________________

Location Location

iii

Notice

iv

Contents

Contents

Chapter 1 Introduction

Features...........................................................................................................................1-1

Related Manuals............................................................................................................ 1-4

Getting Help ..................................................................................................................1-4

Chapter 2 Installing the Modules

Installing EPIMs............................................................................................................2-3

EPIM Revisions ...................................................................................................... 2-3

Installing the EPIM................................................................................................2-4

The Reset Switch ........................................................................................................... 2-5

User-Accessible Components...................................................................................... 2-6

Setting the Module Card DIP Switch.........................................................................2-7

Chapter 3 Operation

Flexible Network Bus (FNB)........................................................................................ 3-2

System Management Buses ......................................................................................... 3-2

SMB-1 Bus...............................................................................................................3-2

SMB-10 Bus.............................................................................................................3-2

System Diagnostic Controller...................................................................................... 3-3

DC/DC Converter ........................................................................................................ 3-3

FNB Interface.................................................................................................................3-3

i960 Core.........................................................................................................................3-4

Chapter 4 LANVIEW LEDs

Chapter 5 Specifications

Safety............................................................................................................................... 5-1

Service.............................................................................................................................5-1

Physical........................................................................................................................... 5-2

Dimensions............................................................................................................. 5-2

Weight...................................................................................................................... 5-2

Environment........................................................................................................... 5-2

v

Contents

Appendix A EPIMs

EPIM-T...........................................................................................................................A-1

EPIM-F1 and EPIM-F2.................................................................................................A-2

EPIM-F3.........................................................................................................................A-3

EPIM-C...........................................................................................................................A-5

Connector Type .....................................................................................................A-5

Grounding..............................................................................................................A-5

EPIM-A and EPIM-X (AUI Port)................................................................................A-5

vi

Introduction

The 9E132-15, 9E133-36, 9E138-12, and 9E138-36 MicroLAN™ Switch Modules,
shown in Figure 1-1, are four channel Ethernet bridges and routers. Up to three
front panel Ethernet networks can be connected to this module and they can be
bridged/routed to any other Ethernet segment and to any other SmartSwitch
9000 module via the FNB bus (acting as the fourth port).

Chapter 1

Features

The 9E132-15, 9E133-36, 9E138-12, and 9E138-36 MicroLAN™ Modules will

NOTE

be referred to collectively as the Ethernet MicroLan Modules.

Processor

The Ethernet MicroLan Switch Modules are equipped with an advanced Intel i960
microprocessor. This microprocessor provides a platform for all management
functions within a scalable RISC-based architecture.

System Management

The Ethernet MicroLan Switch Modules provide interfaces to the two System
Management Buses (SMB-1 and SMB-10) for intermodule management.

Connectivity

The 9E132-15 provides four RJ-45 ports and one EPIM slot for each of the three
channels. See Chapter 5 for information on the use of EPIMs.

The 9E133-36 has one 50-pin front panel for each of the three channels, providing
12 individual Ethernet connections each.

The 9E138-12 provides four ST-type multi-mode fiber optic connections for each
of the three channels, for a total of 12 connections.

1-1

Introduction

The 9E138-36 provides 12 ST-type multi-mode fiber optic connections for each of
the three channels, for a total of 36 connections.

All ports function as repeaters for incoming data which retime and retransmit all
packets.

Bridging/Routing

The Ethernet MicroLan Switch Modules provide Bridging/Routing between the
front panel channels and/or to any other module in the chassis via FNB -1 or
FNB -2 of the FNB bus. IEEE 802.1d Spanning Tree Protocol is supported in all
bridging functions.

Management Information Base (MIB) Support

All concentrator modules provide MIB support including the following:

NOTE

• IETF FDDI MIB

• IETF MIB II

• Cabletron Enterprise MIBs

For a complete list of supported MIBs, refer to the release notes provided in the
module package.

RMON

RMON support (RFC1271).

LANVIEW LEDs

The Ethernet MicroLan Switch Modules use LANVIEW: the Cabletron Systems
built-in visual diagnostic and status monitoring system. With LANVIEW LEDs,
you can quickly identify the device, port, and physical layer status at a glance.

Hot Swapping

The Ethernet MicroLan Switch Modules can be installed or removed from the
chassis while the SmartSwitch 9000 is powered up without affecting the operation
of the remaining modules in the chassis.

1-2

Introduction

ETHERNET

9E132-15

SMB CPU

FNB

1123

2
3
4
5

E
T
H
E
R

2X

N
E
T

3X

1

4X

5X

E
T
H
E
R
N
E
T

2

E

T
H
E
R

2X

N
E
T

3X

3

4X

5X

ETHERNET

9E133-36

SMB CPU

FNB

1123

2
3
4
5
6
7
8

9
10
11
12

12

E
T
H
E
R
N
E
T

1

1

12

E
T

2X

3X

4X

H
E
R
N
E
T

2

5X

1

12

E
T
H
E
R
N
E
T

3

1

ETHERNET

9E138-12

SMB CPU

FNB

1123

ENET 1

3

2

4

ENET 2

1

3

2

4

ENET 3

1

3
4

2

ETHERNET 1

RX

1

TX

RX

2

TX

RX

3

TX

RX

4

TX

ETHERNET 2

RX

1

TX

RX

2

TX

RX

3

TX

RX

4

TX

ETHERNET 3

RX

1

TX

RX

2

TX

RX

3

TX

RX

4

TX

ETHERNET

9E138-36

SMB CPU

FNB

123

ENET 1

3

1
2

4

ENET 2

1

3

2

4

ENET 3

1

3

2

4

ETHERNET 1

RX

1

TX

RX

2

TX

RX

3

TX

RX

4

TX

ETHERNET 2

RX

1

TX

RX

2

TX

RX

3

TX

RX

4

TX

ETHERNET 3

RX

1

TX

RX

2

TX

RX

3

TX

RX

4

TX

ENET 1

ENET 1

5

7

11

9

6

8

10

ENET 2

5
6

ENET 3

5
6

RX

5

TX

RX

6

TX

RX

7

TX

RX

8

TX

RX

5

TX

RX

6

TX

RX

7

TX

RX

8

TX

RX

5

TX

RX

6

TX

RX

7

TX

RX

8

TX

12

ENET 2

9

7

11

8

10

12

ENET 3

9

7

11

8

10

12

RX

9

TX

RX

10

TX

RX

11

TX

RX

12

TX

RX

9

TX

RX

10

TX

RX

11

TX

RX

12

TX

RX

9

TX

RX

10

TX

RX

11

TX

RX

12

TX

Figure 1-1. The Ethernet MicroLan Switch Modules

1-3

Introduction

Related Manuals

The manuals listed below should be used to supplement the procedures and
technical data contained in this manual.

SmartSwitch 9000 Installation Guide
SmartSwitch 9000 Operations Guide
SmartSwitch 9000 9C300-1 Environmental Module User’s Guide
SmartSwitch 9000 9C214-1 AC Power Supply User’s Guide
SmartSwitch 9000 Module Local Management User’s Guide

Getting Help

For additional support related to this device or document, contact the Cabletron Systems Global Call
Center:

Phone [phone]
Internet mail [e-mail]
FTP ctron.com (134.141.197.25)

Login
Password

BBS [phone]

Modem setting 8N1: 8 data bits, No parity, 1 stop bit

For additional information about Cabletron Systems or its products, visit the
World Wide Web site: http://www.cabletron.com/
For technical support, select Service and Support .

To send comments or suggestions concerning this document, contact the
Cabletron Systems Technical Writing Department via the following
email address: [e-mail]

Make sure to include the document Part Number in the email message.

anonymous
your email address

Before calling the Cabletron Systems Global Call Center, have the following information ready:

• Your Cabletron Systems service contract number

• A description of the failure

• A description of any action(s) already taken to resolve the problem (e.g., changing mode switches,
rebooting the unit, etc.)

• The serial and revision numbers of all involved Cabletron Systems products in the network

• A description of your network environment (layout, cable type, etc.)

• Network load and frame size at the time of trouble (if known)

• The device history (i.e., have you returned the device before, is this a recurring problem, etc.)

• Any previous Return Material Authorization (RMA) numbers

1-4

Installing the Modules

The SmartSwitch 9000 module may be installed into any of the 14 slots that are
available. To install, follow the steps below:

1.Remove the blank panel covering the slot that the module is being mounted
in. All other slots must be covered, if modules are not being installed, to
ensure proper airflow and cooling.

2.Carefully remove the module from the shipping box. (Save the box and
packing materials in the event the module must be reshipped.)

3.Attach one end of the ESD wrist strap packaged with the SmartSwitch 9000
chassis to your wrist. Plug the other end into the ESD Wrist Strap Grounding
receptacle in the lower right corner of the SmartSwitch 9000 Chassis shown in
Figure 1.

Chapter 2

4.Remove the module from the plastic bag. Observe all precautions to prevent
damage from Electrostatic Discharge (ESD).

5.Carefully examine the module, checking for damage. If any damage exists,
DO NOT install the module. Contact Cabletron Systems Global Call Center
immediately.

6.Before installing the SmartSwitch 9000 cards into the chassis, ensure that the
bottom and top plastic tabs are unlocked. Slide the card into an available slot
and ensure that the circuit card is between the card guides, as shown in Figure

1. Check both the upper and lower tracks. Take care that the module slides in
straight and engages the backplane connectors properly. Lock down the top
and bottom plastic tabs at the same time, applying even pr

essure.

2-1

Installing the Modules

Plastic Tab

Metal Back-Panel

Jack for ESD
Wrist Strap

Module

Module Guides

Warning:
Ensure that the circuit card is between the card

guides.
Lock down the top and bottom plastic tabs

at the same time, applying even pressure.

Figure 2-1. Installing the Module

2-2

Installing EPIMs

This section contains procedures on how to add/replace an Ethernet Port
MicroLAN Module (EPIM). After installing the EPIM, refer to Appendix A to
verify proper EPIM operation.

Observe all static precautions while handling EPIMs.

!

CAUTION

EPIM Revisions

Revision numbers are located on the EPIM’s Printed Circuit Board directly
following the Part Number as shown in Figure 2-2. Table 2-1 lists the required
board revision for each EPIM.

Installing the Modules

EPIM Board Revision

CABLETRON SYSTEMS INC. PN 9000474 - 04

Figure 2-2. Location of Revision Number

Table 2-1. EPIM Board Revisions

EPIM EPIM BOARD REVISION

EPIM-T 04 or greater
EPIM-F2 05 or greater
EPIM-F1 05 or greater
EPIM-F3 02 or greater

EPIM-C 05 or greater

EPIM-T

EPIM-A Not Applicable
EPIM-X 02 or greater

2-3

Installing the Modules

Installing the EPIM

To install an EPIM:

When removing an EPIM, make sure to pull the module straight out so as not to

NOTE

damage the connector.

1. Remove the coverplate or the EPIM (whichever applies).

2. Slide your new EPIM into place, making sure the connectors on the rear of the
module and inside the HUB attach properly. Refer to Figure 2-3.

3. Install the mounting screw.

EPIM

Mounting

Screw

Figure 2-3. Installing an EPIM

2-4

Installing the Modules

The Reset Switch

The Reset switch is located on the front panel, under the top plastic tab, as shown
in Figure 2-4. (Under the right-side tab on the 9E138-36.) It serves two functions:

• Pressing the Reset switch twice within three seconds causes the processor

(i960) to reset.

• Pressing and holding the switch on for three or more seconds causes the

module to shutdown. Pressing and holding again for three seconds restarts the
module.

SNMP management may be used to disable this switch to enhance module
security.

SMB

Figure 2-4. The Reset Switch

CPU

Reset Switch

2-5

Installing the Modules

User-Accessible Components

Figure 2-5 shows the various components that are accessible to the user. These
consist of an eight-position dip switch (explained in the next section), replaceable
PROMs and sockets for RAM. These will be used for future upgrades.
Instructions for installing the components will be supplied with the upgrade kit.

SMB-1
PROM

Shared DRAM
Socket

Local DRAM
Socket

i960
Processor

Boot PROM
Flash SIMM

Socket

DIP Switch

2-6

Figure 2-5. User-Accessible Components

Installing the Modules

Setting the Module Card DIP Switch

An eight-switch DIP switch is located on the module card, as shown in Figure 2-5
and Figure 2-6. The functions of the switches are listed in Table 2-2.

1
2
3
4
5
6
7
8

Figure 2-6. Location of Module DIP Switch

2-7

1

Installing the Modules

See the Cautions at the end of this table.

Table 2-2. Function of DIP Switch

Switch Function Description

When toggled, this switch clears user-entered

8

Clear

Password

passwords stored in NVRAM and restores the

1

default passwords. Once reset you can use the
defaults or enter new passwords.

The module uses NVRAM to store user­entered parameters such as IP addresses,
device name, etc. To reset these parameters to

7

Clear

NVRAM

the factory defaults, toggle this switch. Once

2

reset you can use the defaults or enter new
parameters, which are stored in NVRAM
when the module is powered down, and
remain there until the switch is toggled again.

!

CAUTION

T oggling this switch after pulling the board out
of the SmartSwitch 9000 clears download

6

Force BootP

Download

information from NVRAM and forces image
files to be downloaded from the station

3

configured to act as that module’s BootP server
(connected to the EPIM on the Environmental
Module).

5 Reserved

4 Reserved

3 Reserved

2 Reserved

1 Reserved

Off - Factory Use Only

Off - Factory Use Only

Off - Factory Use Only

Off - Factory Use Only

Off - Factory Use Only

Caution: Do not toggle Switch 8 unless you intend to reset the user configured

passwords to their factory default settings.

2

Caution: Do not toggle Switch 7 unless you intend to reset the user parameters

to the factory default settings.

3

Caution: Do not toggle switch 6 unless a bootp server is connected to the EPIM

of the Environmental Module.

2-8

Operation

The Ethernet MicroLan Switch Modules provide connectivity between four
interfaces: the three front panel Ethernet and the FDDI rings on the backplane
(FNB-1 or FNB-2).

Chapter 3

SmartSwitch 9000 modules connect to either the Internal Network Bus (INB) or
the Flexible Network Bus (FNB) bus. The Ethernet MicroLan Switch Modules
connect to the FNB bus. Figure 3-1 is a block diagram of the modules. The front
panel contains three Ethernet connections that interface to the Repeater Interface
Controllers (RIC). These function as individual repeating networks; each 12 port
group is a separate collision domain. Front panel Ethernet packets are received
via the RIC. Bridging/Routing may occur between these RICs and/or to any
other SmartSwitch 9000 module via the Flexible Network Bus.

DC/DC

Converter

RIC

RIC

RIC

Figure 3-1. Ethernet MicroLan Switch Modules Block Diagram

System

Diagnostic

Controller

i960 PLUS Core

SMB-1

SMB-10

FNB-1 or

FNB-2

3-1

Operation

Flexible Network Bus (FNB)

The FNB consists of two dual FDDI networks, the FNB-1 and FNB-2, providing
up to 400 Mbps of data bandwidth. These FDDI networks are 100% ANSI FDDI­compliant, supporting SMT (version 7.3), MAC, PHY, and PMD standards. This
allows the FNB to traverse multiple SmartSwitch 9000 hubs, or connect to any
ANSI FDDI-compliant device, through standard A/B port connections.

System Management Buses

There are two management channels within the SmartSwitch 9000 system: the
SMB-1 and the SMB-10. These buses provide out-of-band management and inter­module management communication.

SMB-1 Bus

The SMB-1 is a 1 Mbps management bus located within the SmartSwitch 9000.
This bus is utilized by all diagnostic controllers in the system. These include
connectivity modules, power supply modules, and the environmental module.
The SMB-1 transports inter-chassis information between system components,
such as power and environmental information, as well as diagnostic messages.
Periodic
loop-back tests are performed by all modules that share this bus to ensure the
validity of SMB-1. In the event a failure is detected on SMB-1, the SMB-10 may be
used as an alternate communication channel.

SMB-10 Bus

The SMB-10 is a 10 Mbps management bus located within the SmartSwitch 9000,
which is also used for inter-chassis communication of modules as well as serving
as an out-of-band management channel into the SmartSwitch 9000. The SMB-10 is
externalized from the chassis via an optional Ethernet Port Interface Module
(EPIM) located on the front of the Environmental Module. Through an EPIM
connection, full SNMP management of the SmartSwitch 9000 is available out-of­band from user data. Modules which share the SMB-10 bus periodically send out
loop-back packets to ensure the validity of SMB-10. In the event a fault is detected
on the SMB-10, the SMB-1 can be used as an alternate communication channel by
the modules. Non-runtime downloads and BootP downloads also utilize the
SMB-10 bus.

3-2

System Diagnostic Controller

This diagnostic controller is composed of a Z-80 microprocessor and its
supporting logic. The diagnostic controller is designed to control the power-up
sequencing of modules, monitor the Ethernet MicroLan Switch Modules input
and output power parameters, keep watch over the main host processor, as well
as monitor the temperature and control the SMB LANVIEW diagnostic LED.
Although the diagnostic controller and the main host processor can operate
independently of each other if needed, they exchange information about each
other’s status and overall module condition. The information gathered by the
diagnostic controller is available to the network manager via local/remote
management and the LCD located on the Environmental Module. The Ethernet
MicroLan Switch Modules have been designed so that in the event of a diagnostic
controller fault, the modules will continue to function.

Operation

DC/DC Converter

The DC/DC converter converts the 48 VDC on the system power bus to the
necessary operating voltages for its host network services module. The diagnostic
controller controls the operation of the DC/DC converter.

FNB Interface

SmartSwitch 9000 modules are designed with one of two attachment policies. One
allows dual attachment of a module to either FNB-1 or FNB-2; the second allows
dual attachment to both FNB-1 and FNB-2. The Ethernet MicroLan Switch
Modules have one dual attachment to the FNB backplane, connecting to either
FNB-1 or FNB-2. The module can insert into the FNB or bypass it. These flexible
configuration options make the SmartSwitch 9000 ideal for networks designed to
Bridge/Route multiple lower speed LANs to FDDI and/or networks designed
using an FDDI collapsed backbone.

3-3

Operation

i960 Core

The i960 core in the FNB module serves two major functions: it provides the
packet forwarding logic and performs all network management services. FNB
modules can be configured to run as layer 2 bridges, layer 3 routers, or as Fast
Packet Switches. It is possible to run the bridging and routing options
concurrently, but the SFPS option cannot run with bridging and routing.

The i960 core provides the SNMP protocol stacks, as well as support for industry
standard MIBs. Additionally, Cabletron enterprise extension MIBs are supported
for each media type. Advanced management services, such as the Distributed
LAN Monitor , RMON, telnet, and network address to MAC addr ess mapping, are
also provided by the i960 core.

3-4

LANVIEW LEDs

The front panel LANVIEW LEDs, shown in Figure 4-1, indicate the status of the
module and may be used as an aid in troubleshooting.

Chapter 4

FNB Receive

ETHERNET

SMB CPU

FNB

1123

2
3
4
5

Link (9E138-12
and 9E138-36)

Figure 4-1. LANVIEW LEDs

System Status

FNB Transmit

Ethernet Receive

Ethernet T ransmit

Link (9E132-15
and 9E133-36)

ENET 1

1

3

2

4

4-1

LANVIEW LEDs

The functions of the System Management Bus (SMB) and CPU LEDs are listed in
Table 4-1.

LED Color State Description

Green Functional Fully operational.
Yellow Crippled Not fully operational (i.e., one bad port).
Yellow/Green Booting Blinks yellow and green while booting.
Red Reset Normal power-up reset.
Red (Flashing) Failed Fatal error has occurred.
Off Power off Module powered off.

The function of the FNB Receive LED is listed in Table 4-2.

Table 4-1. SMB and CPU LEDs

Table 4-2. FNB Receive LED

LED Color State

Yellow (Flashing) Activity (Flashing rate indicates rate of activity).
Off No activity

The function of the FNB Transmit LED is listed in Table 4-3.

Table 4-3. FNB Transmit LED

LED Color State

Green (Flashing) Activity (Flashing rate indicates rate of activity).
Off No activity

4-2

The functions of the Ethernet Receive LEDs are listed in Table 4-4.

Table 4-4. Ethernet Receive LEDs

LED Color State

Green Link, No activity
Yellow (Flashing) Link, Activity (Flashing rate indicates rate of

activity)

Off No link, No activity

The functions of the Ethernet Transmit LEDs are listed in Table 4-5.

Table 4-5. Ethernet Transmit LEDs

LED Color State

Green (Flashing) Activity (Flashing rate indicates rate of activity)

LANVIEW LEDs

Yellow (Flashing) Port in standby state
Off No activity

The function of the Link LEDs is listed in Table 4-6.

Table 4-6. Link LEDs

LED Color State

Green Link

Off No link

4-3

LANVIEW LEDs

4-4

Specifications

Safety

It is the responsibility of the person who sells the system to which the module will

!

CAUTION

be a part to ensure that the total system meets allowed limits of conducted and
radiated emissions.

This equipment meets the following safety requirements:

• UL 1950

• CSA C22.2 No. 950

• EN 60950

• IEC 950

• EMI Requirements of FCC Part 15 Class A

• EN 55022 Class A

• VCCI Class I

• EMC the following requirements:

Chapter 5

EN 50082-1
IEC 801-2 ESD
IEC 801-3 Radiated susceptibility
IEC 801-4 EFT

Service

MTBF (MHBK-217E): >200,000 hrs.
MTTR: <0.5 hr.

5-1

Specifications

Physical

Dimensions

All except 9E138-36:

9E138-36:

Weight

All except 9E138-36:

35.0 D x 44.0 H x 3.0 W centimeters
(13.8 D x 17.4 H x 1.2 W inches)

35.0 D x 44.0 H x 6.0 W centimeters
(13.8D x 17.4H x 2.4W inches)

Unit: 1.36 kg. (3 lb)
Shipping: 1.81 kg. (4 lb)

9E138-36:

Unit: 2.7kgs. (6lb)
Shipping: 3.6kgs. (8lb)

Environment

Operating Temperature 5 to 40° C
Storage Temperature -30 to 90° C
Relative Humidity 5% to 95% non-condensing

5-2

EPIMs

The 9E132-15 MicroLAN Switch Extension Module provides one port per channel
for Cabletron Systems EPIMs. EPIMs allow connecting to the 9E132-15 using
different media types. Cabletron Systems offers a variety of EPIMs whose
specifications are explained in the following sections.

Appendix A

NOTE

EPIM-T

Verify that the EPIM is the proper revision before installing. See

EPIM on page 2-4. for details.

The EPIM-T is an RJ-45 connector supporting UTP cabling. It has an internal
Cabletron Systems TPT-T™ 10BASE-T Twisted Pair Transceiver.

The slide switch on the EPIM-T determines the crossover status of the cable pairs.
If the switch is on the X side, the pairs are internally crossed over. If the switch is
on the = side, the pairs are not internally crossed over. Figure A-1 shows the
pinouts for the EPIM-T in both crossover positions.

The link distance is up to 100 meters on unshielded twisted pair cable as specified
by ANSI TP-PMD.

Installing the

A-1

EPIMs

Position X
(crossed over)

1. RX+

2. RX-

3. TX+

4. NC

5. NC

6. TX-

7. NC

8. NC

Position =
(not crossed over)

1. TX+

2. TX-

3. RX+

4. NC

5. NC

6. RX-

7. NC

8. NC

Figure A-1. EPIM-T Pinouts

EPIM-F1 and EPIM-F2

LNK

EPIM-T

The EPIM-F1 and EPIM-F2 support Multimode Fiber Optic cabling. Each EPIM
has an internal Cabletron Systems FOT-F™ Fiber Optic Transceiver. The EPIM-F1
is equipped with SMA Connectors and the EPIM-F2 is equipped with ST
Connectors. Figure A-2 shows both EPIMs. Specifications for the EPIMs ar e listed
in Table A-1.

The link distance is up to 2 kilometers on the multimode fiber-optic cable as
specified by ANSI MMF-PMD.

TX

RX

TX

LNK

EPIM-F1/F2

Figure A-2. EPIM-F1 and EPIM-F2

RX

LNK

EPIM-F1/F2

A-2

Table A-1. EPIM-F1 and EPIM-F2 Specifications

EPIM-F3

Parameter Typical Value

Receive Sensitivity -30.5 dBm -28.0 dBm — —

Peak Input Power -7.6 dBm -8.2 dBm — —

Worst

Case

Worst Case

Budget

Typical
Budget

Transmitter power parameters are listed Table A-2.

Table A-2. Transmitter Power Parameters

Parameter Typical Value

50/125 µm fiber -13.0 dBm -15.0 dBm 13.0 dB 17.5 dB

62.5/125 µm fiber -10.0 dBm -12.0 dBm 16.0 dB 20.5 dB
100/140 µm fiber -7.0 dBm -9.0 dBm 19.0 dB 23.5 dB

Error Rate Better than 10

-10

Worst

Case

Worst Case

Budget

Typical
Budget

The transmitter power levels and receive sensitivity levels listed are Peak Power

NOTE

Levels after optical overshoot. A Peak Power Meter must be used to correctly
compare the values given above to those measured on any particular port. If
Power Levels are being measured with an A verage Power Meter, then 3 dBm must
be added to the measurement to correctly compare those measured values to the
values listed (i.e., -30.5 dBm peak = -33.5 dBm average).

EPIM-F3

The EPIM-F3 supports Single Mode Fiber Optic cabling. It has an internal
Cabletron Systems FOT-F™ Fiber Optic Transceiver and is equipped with ST
Connectors. Figure A-3 shows the EPIM-F3. Specifications for the EPIM-F3 are
listed in Table A-3.

The link distance is up to 40 kilometers (max) and 25 kilometers (typical) on
single mode fiber-optic cable as specified by ANSI SMF-PMD.

A-3

EPIMs

NOTE

TX

RX

Figure A-3. EPIM-F3

LNK

EPIM-F3

Transmitter Power decreases as temperatures rise and increases as temperatures
fall. Use the Output Power Coefficient to calculate increased or decreased power
output for your operating environment. For example, the typical power output at
25°C is -16.4 dBm. For a 4°C temperature increase, multiply the typical
coefficient (-0.15 dBm) by four and add the result to typical output power (4 x -

0.15 dBm + -16.4 = -17.0).

NOTE

Table A-3. EPIM-F3 Specifications

Parameter Typical Minimum Maximum

Transmitter Peak Wave Length 1300 nm 1270 nm 1330 nm
Spectral Width 60 nm - 100 nm
Rise Time 3.0 nsec 2.7 nsec 5.0 nsec
Fall Time 2.5 nsec 2.2 nsec 5.0 nsec
Duty Cycle 50.1% 49.6% 50.7%
Bit Error Rate Better than 10

-10

The transmitter power levels given above are Peak Power Levels after optical
overshoot. You must use a Peak Power Meter to correctly compare the values
given above to those measured on any particular port. If you are measuring power
levels with an Average Power Meter, add 3 dBm to the average power
measurement to correctly compare the average power values measured to the
values listed above (i.e., -33.5 dBm average + 3 dB = -30.5 dBm peak).

A-4

EPIM-C

The EPIM-C supports thin-net coaxial cabling and is equipped with an internal
Cabletron Systems TMS-3™ Transceiver. You can use the TERM switch on the
front of the EPIM-C to set the internal 50-ohm terminator. This eliminates the
need to connect the port to a tee-connector and terminator. Figure A-4 shows the
setting for the terminator switch.

The link distance is up to 185 meters on the thin-net coaxial cables.

EPIM-C

TERM

EPIM-C

Internal Termination Switch
= On (internally terminated)
= Off (need external termination)

Figure A-4. EPIM-C

Connector T ype

This connector type is a BNC receptacle, with gold center contact, for use with
BNC type tee-connectors and RG-58 thin-net cable.

Grounding

For safety reasons, only one end of a thin-net segment should be connected to
earth ground. Connection to earth ground at more than one point on the segment
may cause dangerous ground currents.

The BNC port of the Coaxial Interface Modules is not connected to earth ground.

EPIM-A and EPIM-X (AUI Port)

The EPIM-A is a DB-15 female connector used to attach segments to an external
transceiver . The EPIM-X is equipped with dual internal transceivers. It has a DB15
male connector used to attach segments to an AUI cable. Figure A-5 shows both
modules.

A-5

EPIMs

The AUI Cable must not exceed 50 meters in length. If 28 AWG thin office drop
AUI cable is used, then the maximum cable length is limited to 15.24 meters.

PWR

EPIM-A

Figure A-5. The EPIM-A and EPIM-X

SQE

Table A-4 lists the DB-15 pinouts.

Table A-4. DB-15 Pinouts

Pin Number Represents Pin Number Represents

1 Logic Ref. 10 Transmit ­2 Collision + 11 Logic Ref.
3 Transmit 12 Receive ­4 Logic Ref. 13 Power (+12Vdc)
5 Receive 14 Logic Ref.

EPIM-X

A-6

6 Power Return 15 No Connection
7 No Connection Connector Shell Positive Ground
9 Collision -