Cabletron Systems SmartSwitch 6000, SmartSwitch 6E123-50, 6M146-04, SmartSwitch 6E133-49 User Manual

Page 1
6E123-50 and 6E133-49 MicroLAN
SmartSwitch 6000 Interface Modules
User’s Guide
Ethernet
6E123-50
E
E
N
N
E
E
T
T
1
1
E
E
N
N
E
E
T
T
2
2
Ethernet
6E133-49
COM
E1 E3
E2 E4
COM
E1 E3
E2 E4
Link
Link
Link
1
12
1
12
1
E
E
N
N
E
E
T
T
3
3
12
Link
1
E
E
N
N
E
E
T
T
4
4
12
Link
E
E
N
N
E
E
T
T
1
1
Link
E
E
N
N
E
E
T
T
3
3
Link
1
12
1
12
1
E
E
N
N
E
E
T
T
2
2
12
Link
1
E
E
N
N
E
E
T
T
4
4
12
9032269-04
5
6
Page 2
Page 3
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
1998 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005 All Rights Reserved Printed in the United States of America
Order Number: 9032269-04 August 1998
Cabletron Systems
Inc. All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
is a registered trademark and
SmartSwitch
is a trademark of Cabletron Systems,
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.
WARNING:
party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital
Changes or modifications made to this device which are not expressly approv ed by the
6E123-50 and 6E133-49 User’s Guide i
Printed on Recycled Paper
Page 4
Notice
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT
IMPORTANT:
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (the “Program”) contained in this package. The Program may be contained in firmware, chips or other media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PR OMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
Before utilizing this product, carefully read this License Agreement.
ii 6E123-50 and 6E133-49 User’s Guide
Page 5
CABLETRON SOFTWARE PROGRAM LICENSE
Notice
1. LICENSE
package subject to the terms and conditions of this License Agreement. You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3. APPLICABLE LA W. This License Agreement shall be interpreted and governed under the laws
and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
. You have the right to use only the one (1) copy of the Program provided in this
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY
1. EXCLUSION OF
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MA TERIALS, AND ANY A CCOMPANYING HARDW ARE.
WARRANTY. Except as may be specifically provided by Cabletron in
2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its suppliers.
For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at
252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.
6E123-50 and 6E133-49 User’s Guide iii
Page 6
Notice
DECLARATION OF CONFORMITY
Application of Council Directive(s):
Manufacturer’s Name:
Manufacturer’ s Address:
European Representative Name:
European Representative Address:
Conformance to Directive(s)/Product Standards:
Equipment Type/Environment:
89/336/EEC 73/23/EEC
Cabletron Systems, Inc. 35 Industrial Way
PO Box 5005 Rochester, NH 03867
Mr. J. Solari Cabletron Systems Limited
Nexus House, Newbury Business Park London Road, Newbury Berkshire RG13 2PZ, England
EC Directive 89/336/EEC EC Directive 73/23/EEC EN 55022 EN 50082-1 EN 60950
Networking Equipment, for use in a Commercial or Light Environment.
Industrial
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms to the above directives.
Manufacturer Legal Representative in Europe Mr. Ronald Fotino Mr. J. Solari
___________________________________ ___________________________________
Full Name Full Name Principal Compliance Engineer Managing Director - E.M.E.A.
___________________________________ ___________________________________
Title Title Rochester, NH, USA Newbury, Berkshire, England
___________________________________ ___________________________________
Location Location
iv 6E123-50 and 6E133-49 User’s Guide
Page 7
CONTENTS
CHAPTER 1 INTRODUCTION
1.1 Using This Guide.........................................................................1-1
1.2 Structure of This Guide................................................................1-1
1.3 6E123-50 and 6E133-49 Overview .............................................1-2
1.3.1 Connectivity ....................................................................1-4
1.3.2 Full Duplex Switched Ethernet........................................ 1-4
1.3.3 Management................................................................... 1-4
1.3.4 Switching Options...........................................................1-5
1.3.5 Standards Compatibility.................................................. 1-5
1.3.6 LANVIEW Diagnostic LEDs............................................1-5
1.3.7 Year 2000 Compliant......................................................1-5
1.3.8 Runtime IP Address Discovery.......................................1-6
1.4 Local Management Features.......................................................1-6
1.4.1 Remote Monitoring (RMON)...........................................1-6
1.4.2 Broadcast Suppression................................................... 1-7
1.4.3 Port Redirect Function....................................................1-7
1.4.4 SmartTrunk.....................................................................1-7
1.4.5 Additional Local Management Functions........................ 1-8
1.5 Optional Features........................................................................1-9
1.6 Document Conventions.............................................................1-10
1.7 Getting Help...............................................................................1-11
1.8 Related Manuals........................................................................1-12
CHAPTER 2 NETWORK REQUIREMENTS
2.1 SmartTrunk..................................................................................2-1
2.2 10BASE-T Network .....................................................................2-2
2.3 100BASE-TX Network.................................................................2-2
2.4 100BASE-FX Fiber Optic Network ..............................................2-2
CHAPTER 3 INSTALLATION
3.1 Required Tools............................................................................3-1
3.2 Unpacking the 6E123-50 and 6E133-49 .....................................3-1
3.3 Installing Options.........................................................................3-2
3.4 Installing the 6E123-50 and 6E133-49
into the 6C105 Chassis ...............................................................3-2
6E123-50 and 6E133-49 User’s Guide v
Page 8
Contents
3.5 Connecting to the Network...........................................................3-5
3.5.1 Connecting UTP Cables to the
6E123-50 and 6E133-49.................................................3-6
3.5.2 Connecting a Twisted Pair Segment
to the FE-100TX..............................................................3-8
3.5.3 Connecting a Fiber Optic Segment to the
FE-100FX and FE-100F3..............................................3-10
3.6 Completing the Installation.........................................................3-12
CHAPTER 4 TROUBLESHOOTING
4.1 Using LANVIEW...........................................................................4-1
4.2 FE-100TX LED.............................................................................4-4
4.3 Troubleshooting Checklist............................................................4-6
4.4 Using the RESET Button .............................................................4-7
CHAPTER 5 LOCAL MANAGEMENT
5.1 Overview......................................................................................5-1
5.2 Local Management Keyboard Conventions.................................5-2
5.3 Management Terminal Setup.......................................................5-3
5.3.1 Console Cable Connection..............................................5-3
5.3.2 Connecting an Uninterruptible Power Supply..................5-4
5.3.3 Management Terminal Setup Parameters ......................5-5
5.3.4 Telnet Connections .........................................................5-6
5.4 Accessing Local Management.....................................................5-7
5.4.1 Navigating Local Management Screens..........................5-8
5.4.2 Selecting Local Management Menu Screen Items........5-10
5.4.3 Exiting Local Management Screens..............................5-10
5.5 The Main Menu Screen..............................................................5-12
5.6 Chassis Menu Screen................................................................5-13
5.7 Chassis Configuration Screen ...................................................5-15
5.7.1 Setting the IP Address...................................................5-17
5.7.2 Setting the Subnet Mask...............................................5-18
5.7.3 Setting the Chassis Date...............................................5-19
5.7.4 Setting the Chassis Time ..............................................5-19
5.7.5 Entering a New Screen Refresh Time...........................5-20
5.7.6 Setting the Screen Lockout Time..................................5-21
5.7.7 Setting the Operational Mode........................................5-21
5.8 SNMP Community Names Screen.............................................5-23
5.8.1 Establishing Community Names ...................................5-24
5.9 SNMP Traps Screen..................................................................5-26
5.9.1 Configuring the Trap Table............................................5-27
5.10 Chassis Environmental Screen..................................................5-28
vi 6E123-50 and 6E133-49 User’s Guide
Page 9
Contents
5.11 Port Redirect Function Screen ..................................................5-29
5.11.1 Displaying the Source and Destination Entries............. 5-31
5.11.2 Changing Source and Destination Ports....................... 5-31
5.12 Module Selection Screen...........................................................5-33
5.12.1 Selecting a Module .......................................................5-34
5.13 Module Menu Screen ................................................................5-35
5.14 Module Configuration Menu Screen..........................................5-37
5.15 General Configuration Screen...................................................5-40
5.15.1 Setting the IP Address..................................................5-44
5.15.2 Setting the Subnet Mask............................................... 5-45
5.15.3 Setting the Default Gateway.........................................5-46
5.15.4 Setting the TFTP Gateway IP Address......................... 5-47
5.15.5 Setting the Module Date ...............................................5-47
5.15.6 Setting the Module Time............................................... 5-48
5.15.7 Entering a New Screen Refresh Time ..........................5-48
5.15.8 Setting the Screen Lockout Time.................................. 5-49
5.15.9 Setting the Operational Mode.......................................5-50
5.15.10Setting the Management Mode.....................................5-51
5.15.11Configuring the COM Port ............................................5-51
5.15.12Changing the Com Port Application..............................5-53
5.15.13Clearing NVRAM ..........................................................5-54
5.15.14Enabling/Disabling IP Fragmentation ...........................5-55
5.16 SNMP Community Names Screen............................................5-56
5.16.1 Establishing Community Names................................... 5-58
5.17 SNMP Traps Screen..................................................................5-59
5.17.1 Configuring the Trap Table...........................................5-60
5.18 Switch Configuration Screen.....................................................5-61
5.18.1 Setting the STA............................................................. 5-63
5.18.2 Setting the Age Time ....................................................5-64
5.18.3 Setting (Enabling or Disabling) the Port Status ............5-64
5.19 Module Specific Configuration Menu Screen ............................5-65
5.20 System Resources Screen........................................................5-68
5.20.1 Setting the Reset Peak Utilization ................................5-69
5.21 High Speed Interface Configuration Menu
Screen (6E123-50 Only)............................................................5-70
5.21.1 Configuring an FE-100FX or FE-100F3
in Port 5 or 6 .................................................................5-73
5.21.2 Setting the FE-100FX and FE-100F3
Operational Mode .........................................................5-73
5.21.3 Configuring an FE-100TX in Port 5 or 6 .......................5-74
5.21.4 Setting the FE-100TX Operational Mode...................... 5-74
5.21.5 Setting the FE-100TX Advertised Ability....................... 5-74
6E123-50 and 6E133-49 User’s Guide vii
Page 10
Contents
5.22 Flash Download Screen.............................................................5-75
5.22.1 Image File Download Using TFTP ................................5-78
5.22.2 Image File Download Using RUNTIME.........................5-79
5.22.3 Image File Download Using BootP................................5-80
5.23 Port Redirect Function Screen...................................................5-80
5.23.1 Changing Source and Destination Ports.......................5-82
5.24 Broadcast Suppression Screen .................................................5-83
5.24.1 Setting the Threshold....................................................5-85
5.24.2 Setting the Reset Peak Switch......................................5-85
5.25 Repeater Configuration Menu Screen .......................................5-86
5.26 Repeater Level Security Configuration ......................................5-87
5.26.1 Setting the Repeater Level Security..............................5-89
5.27 Port Level Security Configuration Screen..................................5-90
5.27.1 Setting the Port Level Security......................................5-92
5.28 Module Statistics Menu Screen .................................................5-94
5.29 Switch Statistics Screen.............................................................5-95
5.29.1 Using the Clear Counters Command ............................5-97
5.30 The Interface Statistics Screen..................................................5-97
5.30.1 Displaying Interface Statistics .....................................5-101
5.30.2 Using the Clear Counters Command ..........................5-101
5.31 RMON Statistics Screen ..........................................................5-102
5.31.1 Displaying RMON Statistics ........................................5-106
5.31.2 Using the Clear Counters Command ..........................5-106
5.32 Repeater Statistics Screen ......................................................5-107
5.32.1 Displaying Port Statistics.............................................5-109
5.32.2 Using the Clear Counters Command ..........................5-109
5.33 Network Tools..........................................................................5-110
5.33.1 Built-in Commands......................................................5-112
5.33.2 Special Commands.....................................................5-124
APPENDIX A SPECIFICATIONS
A.1 Device Specifications.................................................................. A-1
A.2 Physical Properties .....................................................................A-1
A.3 Environmental Requirements...................................................... A-1
A.4 Input/Output Ports....................................................................... A-2
A.5 COM Port Pinout Assignments ...................................................A-2
A.6 Regulatory Compliance............................................................... A-3
viii 6E123-50 and 6E133-49 User’s Guide
Page 11
Contents
APPENDIX B FE-100TX, FE-100FX AND FE-100F3
SPECIFICATIONS
B.1 FE-100TX....................................................................................B-1
B.2 FE-100FX....................................................................................B-2
B.3 FE-100F3.....................................................................................B-3
APPENDIX C OPTIONAL INSTALLATIONS AND
MODE SWITCH BANK SETTINGS
C.1 Required Tools............................................................................C-1
C.2 Setting the Mode Switches..........................................................C-1
C.3 Installing Optional Fast Ethernet Interface Modules....................C-4
6E123-50 and 6E133-49 User’s Guide ix
Page 12
Contents
x 6E123-50 and 6E133-49 User’s Guide
Page 13
CHAPTER 1
INTRODUCTION
Welcome to the Cabletron Systems
SmartSwitch 6000 Interface Modules User’s Guide
6E123-50 and 6E133-49 MicroLAN
. This guide describes the 6E123-50 and 6E133-49 interface modules and provides information concerning network requirements, installation, troubleshooting, and the use of Local Management.
1.1 USING THIS GUIDE
Read through this guide completely to understand the interface module features, capabilities, and Local Management functions. A general working knowledge of Ethernet and IEEE 802.3 type data communications networks and their physical layer components is helpful when using these devices.
Unless noted differently, the inf ormation in this guide applies to
NOTE
both SmartSwitch 6000 interface modules, which are referred to as either the “6E123-50 and 6E133-49” or the “modules”.
1.2 STRUCTURE OF THIS GUIDE
This guide is organized as follows:
Chapter 1,
the features of the 6E123-50 and 6E133-49, provides instructions on obtaining additional help and concludes with a list of related manuals.
Chapter 2,
to consider before installing the 6E123-50 and 6E133-49 into the 6C105 SmartSwitch 6000 chassis.
Chapter 3,
modules in the chassis and connect cables to the devices.
Chapter 4,
LANVIEW LEDs that enable you to quickly diagnose network/operational problems.
Introduction
, outlines the contents of this manual, describes
Network Requirements
Installation
Troubleshooting
, provides instructions on how to install the
, details the 6E123-50 and 6E133-49
, explains the network requirements
6E123-50 and 6E133-49 User’s Guide 1-1
Page 14
Chapter 1:
Introduction
Chapter 5,
Local Management
, describes how to access Local Management and use the Local Management screens to manage the 6E123-50, 6E133-49 modules and 6C105 chassis.
Appendix A,
Specifications
, contains information on functionality and operating specifications, connector pinouts, environmental requirements, and physical properties.
Appendix B,
FE-100TX, FE-100FX and FE-100F3 Specifications
, contains information about FE-100TX pinouts and information concerning cable types used with the FE-100FX and FE-100F3.
Appendix C,
Optional Installations and Mode Switch Bank Settings
, describes how to install optional Fast Ethernet Interf ace Modules and how to set the Mode Switches.
1.3 6E123-50 AND 6E133-49 OVERVIEW
The 6E123-50 and 6E133-49, shown in Figure 1-1, are interface modules for the Cabletron Systems 6C105 SmartSwitch 6000 chassis.
The 6E123-50 and 6E133-49 are high-speed network repeater/switch devices that provide four Ethernet networks (MicroLANs ENET 1 through ENET 4), each consisting of 12 repeater ports that share a bandwidth of 10 Mbps. Each Ethernet network supports IEEE 802.1D switching (bridging), IEEE 802.1Q switching and Cabletron Systems SecureFast Switching Virtual Network technology.
Ports 5 and 6 of the 6E123-50 support optional Fast Ethernet Interface Modules and can provide uplinks to 100BASE-TX or 100BASE-FX Fast Ethernet networks. The 6E133-49 is capable of being equipped with a High Speed Interface Module (HSIM) that provides for additional connectivity to other high speed networking technologies such as Asychronous Transfer Mode (ATM), Wide Area Networks (WANs) and Fiber Distributed Data Interface (FDDI).
The 6E123-50 and 6E133-49 switch each Ethernet network (ENET 1 through ENET 4) to one another and to the optional Fast Ethernet Interface Modules of the 6E123-50 or an HSIM installed in the 6E133-49.
1-2 6E123-50 and 6E133-49 User’s Guide
Page 15
6E123-50 and 6E133-49 Overview
Ethernet
6E123-50
CPU
E
E
N
N
E
E
T
T
1
1
E
E
N
N
E
E
T
T
2
2
Link
Link
1
12
1
COM
Ethernet
6E133-49
COM
E1 E3
E2 E4
E1 E3
E2 E4
COM Ports
CPU
Link
1
E
E
N
N
E
E
T
T
3
3
Link
1
E
E
N
N
E
E
T
T
1
1
Link
1
E
E
N
N
E
E
T
T
3
3
Ethernet Networks 1- 4
12
Link
1
E
E
N
N
E
E
T
T
4
4
12
Link
1
E
E
N
N
E
E
T
T
2
2
12
Link
1
E
E
N
N
E
E
T
T
4
4
12
12
12
12
HSIM Slot
5
Fast Ethernet Interface Module Slots (Ports 5 and 6)
6
6E123-50 and 6E133-49 User’s Guide 1-3
Figure 1-1 The 6E123-50 and 6E133-49
Page 16
Chapter 1:
Introduction
1.3.1 Connectivity
The 6E123-50 and 6E133-49 connect to Ethernet networks or workstations through 4 RJ21 ports on the front panel. These ports support 25-pair cable at lengths up to 100 meters. The ports are IEEE 802.3 10BASE-T compliant.
The 6E123-50 has two front panel slots (ports 5 and 6) for optional Fast Ethernet Interface Modules to support an uplink to 100 Mbps Fast Ethernet backbones or a high speed connection to a local server.
The 6E133-49 has one front panel slot for an optional High Speed Interface Module to provide for additional connectivity to other high speed networking technologies such as Asynchronous Transfer Mode (ATM), Fiber Distributed Data Interface (FDDI), and Wide Area Networks (WANs).
1.3.2 Full Duplex Switched Ethernet
The optional Fast Ethernet Interface Modules for the 6E123-50 can be configured to operate in Full Duplex Switched Ethernet mode, which provides 200 Mbps of bandwidth.
1.3.3 Management
Management of the 6E123-50, 6E133-49, 6C105 chassis and any optional equipment (Fast Ethernet Interface Modules and HSIMs) is accomplished using Local Management tools or remote SNMP management stations. Local Management is accessible through the RS232 COM port on the front panel using a local VT100 terminal, or a remote VT100 terminal via a modem connection, and in-band via a Telnet connection. In-band remote management is possible through any SNMP compliant Network Management Software.
1-4 6E123-50 and 6E133-49 User’s Guide
Page 17
6E123-50 and 6E133-49 Overview
1.3.4 Switching Options
The 6E123-50 and 6E133-49 provide 802.1D switching, 802.1Q switching, or SecureFast Switching Virtual Netw ork Services between all of the front panel interfaces including Fast Ethernet Interface Modules and High Speed Interface Modules (HSIMs).
SecureFast switching and 802.1Q switching allow for future migration to Virtual Network technologies without requiring the replacement of existing equipment.
1.3.5 Standards Compatibility
The 6E123-50 and 6E133-49 are fully compliant with the IEEE 802.3 standard. The optional Fast Ethernet Interface Modules are fully compliant with the IEEE 802.3u standard. The 6E123-50 and 6E133-49 provide IEEE 802.1D Spanning T ree Algorithm (STA) support to enhance the overall reliability of the network and protect against “loop” conditions. The 6E123-50 and 6E133-49 support a wide variety of industry standard MIBs including RFC 1213 (MIB II), RFC 1757 (RMON), RFC 1493 (Bridge MIB) and RFC 1354 (FIB MIB). A full suite of Cabletron Systems Enterprise MIBs provide a wide array of statistical information to enhance troubleshooting.
1.3.6 LANVIEW Diagnostic LEDs
LANVIEW diagnostic LEDs serve as an important troubleshooting aid by providing an easy way to observe the status of indi vidual ports and ov erall network operations. Chapter 4 provides details about the 6E123-50 and 6E133-49 LANVIEW LEDs.
1.3.7 Year 2000 Compliant
The 6E123-50, 6E133-49 and 6C105 chassis have an internal clock that can maintain the current time and date beyond the year 1999.
6E123-50 and 6E133-49 User’s Guide 1-5
Page 18
Chapter 1:
Introduction
1.3.8 Runtime IP Address Discovery
This feature enables the modules to automatically accept an IP address from a BootP server on the network into NVRAM without requiring a user to enter an IP address through Local Management.
When the modules are connected to the network and powered up, Runtime IP Address Discovery (RAD) checks the modules for an IP address. If one has not yet been assigned (module and 6C105 chassis IP address set to 0.0.0.0), RAD checks to see if any of the module interfaces have a link. If so, RAD sends out Reverse Address Resolution Protocol (RARP) and BootP requests to obtain an IP address from a RARP or BootP server on the network.
The RAD requests start out at an interval of one second. The interval then doubles after every transmission until an interval of 300 seconds is reached. At this point, the interval remains at 300 seconds. The RAD requests continue until an IP address is received from a RARP or BootP server, or an IP address is entered using Local Management.
1.4 LOCAL MANAGEMENT FEATURES
Local Management provides the tools that allow management of the 6E123-50 and 6E133-49, the Fast Ethernet Interface Modules, the High Speed Interface Module (HSIM) and the 6C105 chassis. Local Management for the 6E123-50 and 6E133-49 provides the features described in Sections 1.4.1 through 1.4.5.
1.4.1 Remote Monitoring (RMON)
The 6E123-50 and 6E133-49 support all Ethernet RMON groups, which include Statistics, Alarms, Events and History. These groups are enabled on all ports by default.
Cabletron Systems RMON Actions is a vendor specific extension of RMON and provides the ability to set an “Action” on any SNMP MIB variable. The Action can be triggered by any RMON Event and/or Alarm. An example of an Action would be to turn off a MIB-2 interface if a broadcast threshold is crossed.
1-6 6E123-50 and 6E133-49 User’s Guide
Page 19
Local Management Features
1.4.2 Broadcast Suppression
Broadcast Suppression allows a user to set a desired limit of receive broadcast frames per port/per second to be forwarded out the other ports on the module up to the set limit. Any broadcast frames above this specified limit are dropped. In the event that broadcast frames are being suppressed, multicast and unicast frames continue to be switched.
1.4.3 Port Redirect Function
The port redirect function, also referred to as “Port Mirroring,” is a troubleshooting tool used to map traffic from a single source port or multiple source ports to a destination port(s) within the chassis. This feature functions at the bit level, which allo ws all packets, including those with errors, to be copied and sent to an analyzer or RMON probe. The analyzer or RMON probe will see the data as if it is directly connected to the LAN segment of the source port(s).
1.4.4 SmartTrunk
SmartTrunk, also referred to as SmartTrunking, is Cabletron Systems’ terminology for load balancing or load sharing. SmartTrunk technology provides an easy-to-implement mechanism to group, or aggregate, multiple links of any technology together to scale the backbone bandwidth beyond the limitations of a single link. All links are user-configurable so administrators can scale the backbone bandwidth by adding SmartTrunk links. The SmartTrunk benefits are as follows:
All purchased bandwidth is used.
Distributed, resilient links increase reliability and performance.
Multiple technologies are supported within a single trunk for maximum flexibility.
For more information about SmartTrunk, refer to the Cabletron Systems
SmartTrunk User’s Guide
.
6E123-50 and 6E133-49 User’s Guide 1-7
Page 20
Chapter 1:
Introduction
1.4.5 Additional Local Management Functions
Local Management also allows the following tasks to be performed:
Manage any module installed in the 6C105 via a single terminal connection.
Assign an IP address and subnet mask to the 6E123-50, 6E133-49 modules and 6C105 chassis.
Select a default gateway.
Control local and remote access.
Designate workstations to receive SNMP traps from the 6E133-49, 6E123-50, and 6C105 chassis.
Configure module specific SNMP MIB objects including the IETF Bridge MIB objects.
Chapter 5 provides detailed information about Local Management of the
6E123-50 and 6E133-49, the optional Fast Ethernet Interface Modules and the 6C105 chassis. The associated High Speed Interface Module user’s guide provides detailed information about Local Management of the applicable HSIM.
1-8 6E123-50 and 6E133-49 User’s Guide
Page 21
Optional Features
1.5 OPTIONAL FEATURES
Options for the 6E123-50 and 6E133-49 are Fast Ethernet Interface Modules and High Speed Interface Modules to add remote uplink capability.
Cabletron Systems offers Fast Ethernet Interface Modules for the 6E123-50 to support uplinks to 100 Mbps Fast Ethernet backbones or high speed connections to local servers. The Fast Ethernet Interface Modules are listed in Table 1-1.
Table 1-1 Fast Ethernet Interface Modules
P/N Description Application
Supports Category 5 Unshielded Twisted Pair (UTP) cabling with an impedance between 85 and 111 ohms.
Supports multimode fiber optic cabling.
Supports single mode fiber optic cabling.
FE-100TX
FE-100FX
FE-100F3
Uses RJ45 connector
Uses SC connector
Uses SC connector
Cabletron Systems offers High Speed Interface Modules for the 6E133-49 to provide for additional connectivity to other high speed networking technologies such as Asynchronous Transfer Mode (ATM), Wide Area Networks (WANs) and Fiber Distributed Data Interface (FDDI). The HSIMs available for the 6E133-49 are listed in the Release Notes.
6E123-50 and 6E133-49 User’s Guide 1-9
Page 22
Chapter 1:
Introduction
1.6 DOCUMENT CONVENTIONS
The following conventions are used throughout this document:
Note
symbol. Calls the reader’s attention to any item of
NOTE
TIP
information that may be of special importance.
Tip
symbol. Conveys helpful hints concerning procedures or
actions.
!
CAUTION
Caution
damage to the equipment.
Electrical Hazard Warning
that could result in personal injury or death due to an electrical hazard.
symbol. Contains information essential to avoid
symbol. Warns against an action
1-10 6E123-50 and 6E133-49 User’s Guide
Page 23
Getting Help
1.7 GETTING HELP
For additional support related to this device or document, contact the Cabletron Systems Global Call Center:
World Wide Web Phone (603) 332-9400
Internet mail support@cabletron.com FTP ftp://ftp.cabletron.com
Login Password
To send comments or suggestions concerning this document, contact the Cabletron Systems Technical Writing Department via the following email address: TechWriting@cabletron.com
Make sure to include the document Part Number in the email message.
http://www .cabletron.com/ For technical support, select
anonymous your email address
Service and Support
Before calling the Cabletron Systems Global Call Center, have the following information ready:
Your Cabletron Systems service contract number
A description of the failure
A description of any action(s) already taken to resolve the problem (e.g., changing mode switches, rebooting the unit, etc.)
The serial and revision numbers of all involved Cabletron Systems
products in the network
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
Any previous Return Material Authorization (RMA) numbers
6E123-50 and 6E133-49 User’s Guide 1-11
Page 24
Chapter 1: Introduction
1.8 RELATED MANUALS
The following manuals may help to set up, control, and manage the 6E123-50 and 6E133-49:
Cabletron Systems HSIM-A6DP User’s Guide Cabletron Systems HSIM-F6 User’s Guide Cabletron Systems HSIM-FE6 User’s Guide Cabletron Systems HSIM-W6 User’s Guide Cabletron Systems HSIM-W84 User’s Guide Cabletron Systems HSIM-W87 User’s Guide Cabletron Systems HSIM-G01/G09 User’s Guide Cabletron Systems Ethernet Technology Guide Cabletron Systems Cabling Guide Cabletron Systems Port Based VLAN User’s Guide Cabletron Systems SmartTrunk User’s Guide These manuals can be obtained from the World Wide Web in Adobe
Acrobat Portable Document Format (PDF) at the following site:
http://www.cabletron.com/
All documentation for the Cabletron Systems SecureF ast VLAN
NOTE
Manager software is contained on the VLAN Manager CD-ROM.
1-12 6E123-50 and 6E133-49 User’s Guide
Page 25
CHAPTER 2
NETWORK REQUIREMENTS
Before installing the 6E123-50 and 6E133-49 or Fast Ethernet Interface Modules (FE-100TX, FE-100FX, or FE-100F3), revie w the requirements and specifications referred to in this chapter concerning the following:
SmartTrunk (Section 2.1)
10BASE-T Twisted Pair Network (Section 2.2)
100BASE-TX Twisted Pair Network (Section 2.3)
100BASE-FX Fiber Optic Network (Section 2.4)
The network installation must meet the guidelines to ensure satisfactory performance of this equipment. Failure to follow the guidelines may produce poor network performance.
The Cabletron Systems Cabling Guide and SmartTrunk User’s
NOTE
Guide, referred to in the following sections, can be found on the Cabletron Systems W orld Wide W eb site: http://www.cabletron.com/
2.1 SmartTrunk
To connect the 6E123-50 and 6E133-49 to a network so it can take advantage of the SmartTrunk feature, there are certain rules concerning port connections and configurations that must be followed for proper operation. Refer to the Cabletron Systems SmartTrunk User’s Guide for additional information.
6E123-50 and 6E133-49 User’s Guide 2-1
Page 26
Chapter 2: Network Requirements
2.2 10BASE-T NETWORK
When connecting a 10BASE-T segment to any of the 6E123-50 and 6E133-49 ports (ENET 1 through 4), ensure that the network meets the Ethernet network requirements of the IEEE 802.3 standard for 10BASE-T. Refer to the Cabletron Systems Cabling Guide for details.
2.3 100BASE-TX NETWORK
The 6E123-50, with an FE-100TX installed in ports 5 or 6, provides an RJ45 connection that supports UTP cabling. The device at the other end of the twisted pair segment must meet IEEE 802.3u 100BASE-TX Fast Ethernet network requirements for the devices to operate at 100 Mbps. Refer to the Cabletron Systems Cabling Guide for details.
The 6E123-50 with an FE-100TX installed is capable of
NOTE
operating at either 10 or 100 Mbps. The FE-100TX automatically senses the speed of the other device and adjusts its speed accordingly.
2.4 100BASE-FX FIBER OPTIC NETWORK
Ports 5 and 6 of the 6E123-50 support the Cabletron Systems FE-100FX and FE-100F3 fiber optic interface modules. The device at the other end of the fiber optic segment must meet the 100BASE-FX Fast Ethernet network requirements to operate at 100 Mbps. Refer to the Cabletron Systems Cabling Guide for details.
Multimode Mode Fiber Optic Cable Length
The maximum multimode fiber optic cable length of a 100BASE-FX segment is covered in the Cabletron Systems Cabling Guide.
Single Mode Fiber Cable Lengths
The maximum single mode fiber optic length of a 100BASE-FX se gment may be no more than 5 km between Data Terminal Equipment (DTE to DTE) in half duplex mode or 20 km (DTE to DTE) in full duplex mode.
2-2 6E123-50 and 6E133-49 User’s Guide
Page 27
CHAPTER 3
INSTALLATION
Only qualified personnel should install the 6E123-50 and 6E133-49.
This chapter covers the following items:
Required tools (Section 3.1)
Unpacking the 6E123-50 and 6E133-49 (Section 3.2)
Installing the 6E123-50 and 6E133-49 in the 6C105 chassis
(Section 3.4)
Connecting to the network (Section 3.5)
3.1 REQUIRED T OOLS
A Phillips screwdriver is required to install the Fast Ethernet Interface Modules in the 6E123-50.
3.2 UNPACKING THE 6E123-50 AND 6E133-49
1. Open the box and remove the packing material protecting the module.
2. Verify the contents of the carton as listed in Table 3-1.
Table 3-1 Contents of 6E123-50 and 6E133-49 Carton
Item Quantity
6E123-50 or 6E133-49 1 Release Notes 1 RJ21 Angle Adapter 4
6E123-50 and 6E133-49 User’s Guide 3-1
Page 28
Chapter 3: Installation
3.3 INSTALLING OPTIONS
Install any optional equipment before proceeding to
NOTE
Section 3.4.
If the 6E123-50 will be installed with an optional Fast Ethernet Interface Module refer to Appendix C for installation instructions. The installation instructions for the HSIMs available for the 6E133-49 are located in the associated user’s guide.
3.4 INSTALLING THE 6E123-50 AND 6E133-49
INTO THE 6C105 CHASSIS
Failure to observe static safety precautions could cause
!
CAUTION
!
CAUTION
damage to the 6E123-50 and 6E133-49. Follow static safety handling rules and properly wear the antistatic wrist strap provided with the 6C105 chassis.
Do not cut the non-conductive bag to remove the module. Damage could result from sharp objects contacting the board or components.
The 6E123-50 and 6E133-49 can be installed in any of the 5 slots that are available. To install a module, proceed as follows:
1. Remove the blank panel covering the slot in which the module will be
installed. All other slots must remain covered to ensure proper airflow and cooling. (Save the blank plate in the event you need to remove the module.)
2. Carefully remove the module from the shipping box. (Save the box
and packing materials in the event the module must be reshipped.)
3. Locate the antistatic wrist strap shipped with the 6C105 chassis.
Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the 6C105.
3-2 6E123-50 and 6E133-49 User’s Guide
Page 29
Installing the 6E123-50 and 6E133-49 into the 6C105 Chassis
4. Remove the module from the plastic bag. (Save the bag in the event
the module must be reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD).
5. Examine the module for damage. If any damage exists, DO NOT
install the module. Immediately contact the Cabletron Systems Global Call Center.
To pre v ent damaging the backplane connectors in the f ollo wing
!
CAUTION
NOTE
step, take care that the module slides in straight and properly engages the backplane connectors.
In the following step, ensure that the top plastic locking tab lines up with the desired slot number located on the front panel of the chassis. Refer to Figure 3-1.
6. Locate the slot guides that line up with the number of the slot in which
the module will be installed. Install the module in the chassis by aligning the module circuit card between the upper and lower metal rail guides of the desired slot, sliding it into the chassis, and locking down the top and bottom plastic locking tabs, as shown in Figure 3-1. Take care that the module slides in straight and properly engages the backplane connectors.
6E123-50 and 6E133-49 User’s Guide 3-3
Page 30
Chapter 3: Installation
Slot Number
Plastic Locking Tab
1
2
3
45
Ethernet
6E133-49
CPU
E
E
N
N
E
E
T
T
1
1
E
E
N
N
E
E
T
T
3
3
PS1
E1 E3
COM
E2 E4
Link
Link
1
1
E
E
N
N
E
E
T
T
2
2
12
12
Link
Link
1
1
E
E
N
N
E
E
T
T
4
4
12
12
PS2
Metal Back-Panel
Figure 3-1 Installing an Interface Module
3-4 6E123-50 and 6E133-49 User’s Guide
Circuit Card
Card Guides
Plastic Locking Tab
2269_02
Page 31
Connecting to the Network
3.5 CONNECTING TO THE NETWORK
This section provides the procedures for connecting UTP and fiber optic segments from the network or other devices to the modules.
Ethernet segments 1 through 4 on the 6E123-50 and 6E133-49 have four RJ21 connectors for UTP connections. Ports 5 and 6 of the 6E123-50 support FE-100TX, FE-100FX, or FE-100F3 Fast Ethernet Interface Modules. The FE-100TX has an RJ45 connector for a Twisted Pair cable connection. The FE-100FX has an SC style connector for a multimode fiber optic cable connection. The FE-100F3 has an SC style connector for a single mode fiber optic cable connection.
Refer to Section 3.5.1 to make UTP connections to Ethernet segments 1 through 4 of the 6E123-50 and 6E133-49.
Refer to Section 3.5.2 to make a twisted pair connection to an FE-100TX. Refer to Section 3.5.3 to make a fiber optic connection to an FE-100FX or
FE-100F3.
6E123-50 and 6E133-49 User’s Guide 3-5
Page 32
Chapter 3: Installation
3.5.1 Connecting UTP Cables to the
6E123-50 and 6E133-49
When facing the front panel of the 6E123-50 and 6E133-49, the four RJ21 connectors represent Ethernet MicroLAN networks 1 through 4 that contain 12 ports each. All the RJ21 connectors have internal crossovers.
Connect a twisted pair segment to the 6E123-50 and 6E133-49 as follows:
1. Ensure that the device connected to the other end of the segment is
powered ON.
2. If using an RJ21 straight connector, plug it into the appropriate RJ21
port as shown in Figure 3-2 or, if using the RJ21 angle adapter supplied with the device, insert the RJ21 angle adapter as shown in
Figure 3-3. The RJ21 angle adapter allows the cable to be inserted
without interfering with the proper attachment of other connectors.
.
1
1
3
3
Screw Hole
Screw
12 12
Link Status LEDs
Link
1
E
E
N
N
E
E
T
T
2
2
E N E T
4
12
Link
1
E N E T
4
12
Screw
Screw Hole
Figure 3-2 6E123-50 and 6E133-49 Twisted Pair Connection
3-6 6E123-50 and 6E133-49 User’s Guide
Page 33
Connecting to the Network
T
T
T
T
Clip
Clip
Screw
Screw
Screw Hole
Screw Hole
1
1
E
E
N
N
E
E
T
T
2
2
3
3
12 12
Link
1
E
E
N
N
E
E
T
T
4
4
12
Link
Link Status LEDs
1
12
Figure 3-3 Connection Using the RJ21 Angle Adapter
3. Tighten the two screws on the RJ21 connector or RJ21 angle adapter,
as applicable, to secure it to the module.
The cable pinouts for a 25-pair cable (RJ21) can be found in
NOTE
the Cabletron Systems
Cabling Guide
. Refer to Section 1.8, for
details on how to obtain this document.
4. If using the RJ21 angle adapter, plug the 25 pair cable into the adapter
until the two retaining clips, shown in Figure 3-3, snap into place.
6E123-50 and 6E133-49 User’s Guide 3-7
Page 34
Chapter 3: Installation
5. Verify that a link exists by checking that the port Link LEDs are on
(solid green). If the Link LEDs are off, perform the following steps until they are on:
a. Verify that the 10BASE-T device at the other end of the twisted
pair segment is ON and connected to the segment.
b. Verify that the RJ21 connectors on the twisted pair segment have
the proper pinouts and check the cable for continuity.
c. Check that the twisted pair connection meets the dB loss and cable
specifications outlined in Chapter 2.
If a link is not established, contact Cabletron Systems Global Call Center . Refer to Section 1.7 for details.
6. Repeat steps 1 through 4, above, until all connections have been made.
3.5.2 Connecting a Twisted Pair Segment
to the FE-100TX
An FE-100-TX installed in port 5 and/or 6 has an internal crossover switch. When connecting a workstation, use a straight-through cable and set the Fast Ethernet Interface Module crossover switch shown in
Figure 3-4 to the crossed over position marked with X. When connecting
networking devices, such as another bridge, repeater, or router, use a straight-through cable and set the Fast Ethernet Interface Module crossover switch shown in Figure 3-4 to the straight-through position, marked with =.
If the wires do not cross over, use the switch on the FE-100TX to internally cross over the RJ45 port. Figure 3-4 shows how to properly set the FE-100TX crossover switch.
Position X (crossed over)
Position = (not crossed over)
1. RX+
2. RX-
3. TX+
4. NC
5. NC
6. TX-
7. NC
8. NC
Figure 3-4 FE-100TX Crossover Switch
3-8 6E123-50 and 6E133-49 User’s Guide
x
FE-100TX
5. NC
6. RX-
7. NC
8. NC
16651_05
10
100
1. TX+
2. TX-
3. RX+
=
4. NC
Page 35
Connecting to the Network
Connect an FE-100TX to a twisted pair segment as follows:
1. Ensure that the device connected to the other end of the segment is
powered ON.
2. Connect the twisted pair segment to the module by inserting the RJ45
connector on the twisted pair segment into the RJ45 port on the module shown in Figure 3-4.
3. Verify that a link exists by checking that the port RX LED is on
(flashing amber, blinking green, or solid green). If the RX LED is off, perform the following steps until it is on:
a. Verify that the 100BASE-TX device at the other end of the twisted
pair segment is powered up.
b. Verify that the RJ45 connector on the twisted pair segment has the
proper pinouts.
c. Check the cable for continuity. d. Make sure that the twisted pair connection meets dB loss and cable
specifications outlined in Chapter 2.
e. Confirm that the crossover switch is in the correct position.
If a link is not established, contact Cabletron Systems Global Call Center . Refer to Section 1.7 for details.
6E123-50 and 6E133-49 User’s Guide 3-9
Page 36
Chapter 3: Installation
3.5.3 Connecting a Fiber Optic Segment to the
FE-100FX and FE-100F3
The FE-100FX and FE-100F3 have an SC style network port (see
Figure 3-5). Cabletron Systems supplies fiber optic cable that uses SC
style connectors that are keyed to ensure proper crossing over of the transmit and receive fibers.
NOTES
Fiber Optic Network Connection
An odd number of crossovers (preferably one) must be maintained between devices so that the transmit port of one device is connected to the receive port of the other device and vice versa.
If the fiber optic cable being used has SC style connectors that do not resemble MIC style connectors, or has SC connectors on one end and a different type on the other, such as ST connectors, ensure that the proper crossing over occurs.
To connect an FE-100FX or FE-100F3 to the network, perform the following steps:
1. Remove the protective plastic covers from the fiber optic ports on the
applicable port on the module and from the ends of the connectors.
Leave the protective rubber covers in place when the
NOTE
connectors are not in use to prevent contamination.
The FE-100F3 uses Class 1 lasers. Do not use optical
!
CAUTION
3-10 6E123-50 and 6E133-49 User’s Guide
instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard. When viewing the output optical port, power must be removed from the network adapter.
Do not touch the ends of the fiber optic strands, and do not let the ends come in contact with dust, dirt, or other contaminants. Contamination of the ends causes problems in data transmissions. If the ends become contaminated, blow the surfaces with a canned duster. A fiber port cleaning swab saturated with optical-grade isoprop yl alcohol may also be used to clean the ends.
Page 37
Connecting to the Network
2. Insert one end of the SC connector into the FE-100FX or FE-100F3
installed in the 6E123-50. See Figure 3-5.
3. At the other end of the fiber optic cable, attach the SC connector to the
other device.
FE-100FX
16
65
RX LED
Figure 3-5 FE-100FX and FE-100F3 Port
TX LED
4. Verify that a link exists by checking that the port RX LED is on
(flashing amber, blinking green, or solid green). If the RX LED is off and the TX LED is not blinking amber, perform the following steps until it is on:
The port RX LED flashes green and amber during bootup.
NOTE
a. Check that the power is turned on for the de vice at the other end of
the link.
b. Verify proper crossing over of fiber strands between the
applicable port on the 6E123-50 and the fiber optic device at the other end of the fiber optic link segment.
c. Verify that the fiber connection meets the dB loss specifications
outlined in Cabletron Systems Cabling Guide.
If a Link has not been established, contact Cabletron Systems Global Call Center. Refer to Section 1.7 for details.
6E123-50 and 6E133-49 User’s Guide 3-11
Page 38
Chapter 3: Installation
3.6 COMPLETING THE INSTALLATION
After installing the 6E123-50 and 6E133-49 and any optional Fast Ethernet Interface Modules or HSIM as appropriate, the modules are now ready to be set up through Local Management. Refer to Chapter 5 to configure the modules and 6C105 chassis.
3-12 6E123-50 and 6E133-49 User’s Guide
Page 39
CHAPTER 4
TROUBLESHOOTING
This chapter provides information concerning the following:
Using the LANVIEW diagnostic and status monitoring system
Troubleshooting network and module operational problems
Using the RESET button
4.1 USING LANVIEW
The 6E123-50 and 6E133-49 use Cabletron Systems built-in visual diagnostic and status monitoring system called LANVIEW. The LANVIEW LEDs (Figure 4-1) allow quick observation of the network status to aid in the diagnosing of network problems. Refer to Table 4-1 for a description of the LEDs.
For a functional description of the LANVIEW LED on the optional Fast Ethernet Interface Module (FE-100TX), refer to Section 4.2.
All LEDs for the High Speed Interface Module (HSIM) are located on the HSIM and are described in the associated HSIM user’s guide.
The terms flashing, blinking, and solid used in the LED
NOTE
definition tables of this chapter indicate the following:
Flashing indicates an irregular LED pulse. Blinking indicates a steady LED pulse (50% on, 50% off). Solid indicates a steady LED light. No pulsing.
6E123-50 and 6E133-49 User’s Guide 4-1
Page 40
Chapter 4: Troubleshooting
CPU LED
Ethernet
6E133-49
CPU
COM
Receive (RX) Transmit (TX)
E1 E3
E2 E4
Ethernet Status LEDs
Link
1
E
E
N
N
E
E
T
T
1
1
E
E
N
N
E
E
T
T
2
2
E
E
N
N
E
E
T
T
3
3
12
Link
1
E
E
N
N
E
E
T
T
4
4
12
Port Link Status LEDs
Link
1
12
Port Link Status LEDs
Link
1
12
4-2 6E123-50 and 6E133-49 User’s Guide
2269_04
Figure 4-1 LANVIEW LEDs
Page 41
Using LANVIEW
Table 4-1 LANVIEW LEDs
LED Color State Recommended Action
Off Power off. Power up chassis.
CPU
Ethernet Status (RX) of ENET1–4 and ports 5 and 6 of the 6E123-50
Blinking. Hardware failure has occurred.
Contact the Cabletron Systems Global Call Center.
Red
Solid. Resetting, normal power up reset.
Blinking. Crippled.
Amber
No action. Contact the Cabletron
Systems Global Call Center.
Solid. Testing. No action. Green Solid. Functional. No action. Amber
and Green
Booting. Blinks amber
and green while
booting.
No action.
No link. No activity. Off
Port enabled or
No error.
disabled. Green
Amber
Blinking. Port
disabled, link.
Flashing. Port
enabled, link, activity.
No error.
No error. Contact the Cabletron
Red Diagnostic failure.
Systems Global Call Center for assistance.
Should flash green every 2
Off
Port enabled, and no
activity.
seconds indicating BPDUs being sent if STA is enabled and there is a valid link.
Ethernet Status (TX) of ENET1–4 and ports 5 and 6 of the 6E123-50
Port Link Status
Green
Amber
Red
Green Solid. Valid link. No action Off No link Refer to Section 4.3.
Flashing. Indicates
activity. Rate indicates
data rate.
Blinking. Port in
standby, link.
Flashing. Indicates
collision rate.
Solid. Diagnostic
Failure.
No action.
Port may be disabled due to Spanning Tree.
No action. Contact the Cabletron
Systems Global Call Center for assistance.
6E123-50 and 6E133-49 User’s Guide 4-3
Page 42
Chapter 4: Troubleshooting
4.2 FE-100TX LED
The optional FE-100TX has one LED labeled 10/100. The 10/100 LED together with the Receive LED allows the user to determine the Link status and the operating speed of the Fast Ethernet Interface Module. The 10/100 LED and the Receive (RX) LED are shown in Figure 4-2.
Table 4-2 and Table 4-3 provide a functional description of the FE-100TX
LED when the RX LED is on or off, respectively.
10
LED
100
=
x
Receive (RX) LED
FE-100TX
5
10
100
22
6
Figure 4-2 FE-100TX LED
A link exists if the associated port (port 5 or 6) Receive (RX)
NOTE
LED Color Description
10/100
LED is on.
Table 4-2 FE-100TX LED Indications When the RX LED Is On
Off FE-100TX is operating at 10 Mbps. Green FE-100TX is operating at 100 Mbps.
4-4 6E123-50 and 6E133-49 User’s Guide
Page 43
No link exists if the associated port (port 5 or 6) Receive (RX)
NOTE
LED Color Description
10/100
LED is off.
Table 4-3 FE-100TX LED Indications When the RX LED Is Off
No link or no cable attached. FE-100TX
Off
forced to 10 Mbps operation, or is manually set to “auto-negotiate” mode.
FE-100TX LED
Green
No link or no cable attached. FE-100TX is forced to 100 Mbps operation.
6E123-50 and 6E133-49 User’s Guide 4-5
Page 44
Chapter 4: Troubleshooting
4.3 TROUBLESHOOTING CHECKLIST
If the 6E123-50 and 6E133-49 is not working properly, refer to Table 4-4 for a checklist of possible problems, causes, and recommended actions to resolve the problem.
Table 4-4 Troubleshooting Checklist
Problem Possible Cause Recommended Action
All LEDs are OFF.
No Local Management Password screen.
Cannot contact the 6E123-50 and 6E133-49 from in-band management.
Loss of Power to the 6C105 chassis.
6E123-50 and 6E133-49 not properly installed.
Autobaud enabled. Terminal setup is not
correct. Improper console cable
pinouts. Improper Community
Names Table. 6E123-50 or 6E133-49
does not have an IP address.
Port is disabled. Enable port.
Check the proper connection of the power cable and its access to a live outlet.
Check the installation. Press ENTER (RETURN)
(may take up to four times). Refer to Chapter 5 for proper
setup procedures. Refer to Appendix A for
proper console port pinouts. Refer to Section 5.16
for Community Names Table setup.
Refer to Section 5.15.1 for IP address assignment procedure.
No link to device. Check link to device.
Port(s) goes into standby for no apparent reason.
User parameters (IP address, Device and Module name, etc.) are lost when the 6E133-49 or 6E123-50 is powered down or the front panel RESET button is pressed.
6E133-49 or 6E123-50 detects a looped condition.
Mode switch (7), NVRAM Reset, was changed sometime before either cycling power or pressing the RESET button, causing the user-entered parameters to reset to factory default settings.
Review network design and delete unnecessary loops.
Reenter the lost parameters as necessary. Call the Cabletron Systems Global Call Center if problem continues.
4-6 6E123-50 and 6E133-49 User’s Guide
Page 45
Using the RESET Button
4.4 USING THE RESET BUTTON
The RESET button, located near the upper plastic locking tab of the module, (refer to Figure 4-3) resets the 6E123-50 and 6E133-49 processor without affecting the NVRAM.
Pressing the RESET button resets the device, and all current
!
CAUTION
switching being performed by the module is halted. A module downtime of up to two minutes will result from this action.
Ethernet
6E133-49
Reset Button
Figure 4-3 RESET Button
To reset the 6E123-50 and 6E133-49 processor, press and release the RESET button. The module processor goes through a reset process of approximately 20 seconds. Additional downtime may be added as the module reenters the network.
6E123-50 and 6E133-49 User’s Guide 4-7
Page 46
Chapter 4: Troubleshooting
4-8 6E123-50 and 6E133-49 User’s Guide
Page 47
CHAPTER 5
LOCAL MANAGEMENT
This chapter explains how to set up a management terminal to access 6E123-50 and 6E133-49 Local Management. It also explains how to use the Local Management screens and commands.
The Local Management screens shown in this chapter are for
NOTE
5.1 OVERVIEW
Local Management for the 6E123-50 and 6E133-49 consists of a series of management screens that allow the management of the module, the attached segments and the 6C105 chassis. The management screens allo w the user to perform the following tasks:
the 6E123-50. The 6E133-49 shares most of the following Local Management screens. All Local Management functions specific to any of the interface modules are preceded b y a Note to alert the reader.
Manage any interface module in the chassis via a connection to a
single interface module.
Assign IP addresses and subnet masks to the 6E123-50 and 6E133-49
modules, and the 6C105 chassis.
Control access to the 6E123-50 and 6E133-49 modules, and the 6C105
chassis by establishing community names.
Download a new image of operating software.
Designate which Network Management Workstations receive SNMP
traps from the 6E123-50 and 6E133-49 modules, and the 6C105 chassis.
Monitor the environmental status of the 6C105 chassis.
View switch, interface, and RMON statistics.
Assign ports to operate in standard or full duplex mode.
Enable trunking of ports to perform load sharing.
Configure the Fast Ethernet Interface Modules of the 6E123-50 and
the HSIM of the 6E133-49.
6E123-50 and 6E133-49 User’s Guide 5-1
Page 48
Chapter 5: Local Management
There are three ways to access Local Management:
Locally using a VT type terminal connected to the COM port of the
6E133-49 or 6E123-50.
Remotely using a VT type terminal connected through a modem.
In-band through a Telnet connection.
5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONS
All key names appear as capital letters in this manual. Table 5-1 explains the keyboard conventions and the key functions that are used.
Table 5-1 Keyboard Conventions
Key Function
ENTER Key RETURN Key
ESCAPE (ESC) Key
SPACE bar BACKSPACE Key
Arrow Keys
These are selection keys that perform the same Local Management function. For example, “Press ENTER” means that you can press either ENTER or RETURN, unless this manual specifically instructs you otherwise.
This key allows an escape from a Local Management screen without saving changes. For example, “Press ESC twice” means the ESC key must be pressed quickly two times.
These keys cycle through selections in some Local Management fields. Use the SPACE bar to cycle forward through selections and use BACKSPACE to cycle backward through selections.
These are navigation keys. Use the UP-ARROW, DOWN-ARROW, LEFT-ARROW, and RIGHT-ARROW keys to move the screen cursor. For e xample , “Use the arrow keys” means to press whichever arrow key moves the cursor to the desired field on the Local Management screen.
[–] Key
DEL Key
5-2 6E123-50 and 6E133-49 User’s Guide
This key decreases values from a Local Management increment field. For example, “Press [–]” means to press the minus sign key.
The DEL (Delete) key removes characters from a Local Management field. For e xample , “Press DEL” means to press the Delete key.
Page 49
Management T erminal Setup
5.3 MANAGEMENT T ERMINAL SETUP
Use one of the following systems to access Local Management:
An IBM or compatible PC running a VT series emulation software
package
A Digital Equipment Corporation VT100 type terminal
A VT type terminal running emulation programs for the Digital
Equipment Corporation VT100 series
A remote VT100 type terminal via a modem connection
In-band via a Telnet connection
5.3.1 Console Cable Connection
Use the Console Cable Kit provided with the 6C105 chassis to attach the management terminal to the COM port as shown in Figure 5-1.
Connect an IBM PC or compatible device, running the VT terminal emulation, to the 6E123-50 and 6E133-49 as follows:
1. Connect the RJ45 connector at one end of the cable (supplied in the
kit) to the COM port on the 6E123-50 and 6E133-49.
2. Plug the RJ45 connector at the other end of the cable into the
RJ45-to-DB9 adapter (supplied in the kit).
3. Connect the RJ45-to-DB9 adapter to the PC communications port.
Ethernet
6E133-49
E1 E3
COM
E2 E4
CPU
Link
Link
1
1
E
E
N
N
E
E
T
T
2
2
12
12
RJ45 COM Port
1
2345
PS1
Ethernet
6E133-49
CPU
E
E
N
N
E
E
T
T
1
1
E
E
N
N
E
E
T
T
3
3
PS2
E1E3
COM
E2E4
Link
Link
1
1
E
E
N
N
E
E
T
T
2
2
12
12
Link
Link
1
1
E
E
N
N
E
E
T
T
4
4
12
12
E
E
N
N
E
E
T
T
1
1
Figure 5-1 Management Terminal Connection
6E123-50 and 6E133-49 User’s Guide 5-3
PC
RJ45-to-DB9
PC Adapter
UTP Cable
With RJ45 Connectors
226950
Page 50
Chapter 5: Local Management
5.3.2 Connecting an Uninterruptible Power Supply
If the 6C105 chassis is connected to an American Power Conversion (APC) Uninterruptible Power Supply (UPS) for protection from a loss of power, a connection from the COM port of a module to the UPS can be made to monitor the status of the UPS. To use the COM port for this purpose, it must be reconfigured to support the UPS application. This procedure is performed from the General Configuration screen of the interface module. Section 5.15.11, Configuring the COM P ort, pro vides detailed instructions on configuring the COM port for UPS applications. Refer to the UPS documentation for details on how to access the status information.
Use the Console Cable Kit provided with the 6C105 chassis to attach the UPS to the module COM port as shown in Figure 5-2.
Connect the UPS device to the COM port of the 6E123-50 and 6E133-49 as follows:
1. Connect the RJ45 connector at one end of the cable to the COM port
on the 6E123-50 and 6E133-49.
2. Plug the RJ45 connector at the other end of the cable into the
RJ45-to-DB9 male (UPS) adapter, Cabletron Systems Part No.
9372066.
3. Connect the RJ45-to-DB9 male (UPS) adapter to the female DB9 port
on the rear of the UPS device (refer to the particular UPS device’s user instructions for more specific information about the monitoring connection).
Ethernet
6E133-49
E1 E3
COM
E2 E4
CPU
Link
Link
1
E
E
N
N
E
E
T
T
1
1
1
E
E
N
N
E
E
T
T
2
2
12
12
COM Port
DB9 Port
1
2345
PS1
PS2
Ethernet
6E133-49
E1E3
COM
E2E4
CPU
Link
Link
1
1
E
E
E
E
N
N
N
N
E
E
E
E
T
T
T
T
1
2
1
2
12
12
Link
Link
1
1
E
E
E
E
N
N
N
N
E
E
E
E
T
T
T
T
4
3
4
3
12
12
UPS Device
RJ45-to-DB9 UPS Adapter
Figure 5-2 Uninterruptible Power Supply (UPS)
5-4 6E123-50 and 6E133-49 User’s Guide
UTP Cable
With RJ45 Connectors
226951
Page 51
Management T erminal Setup
5.3.3 Management Terminal Setup Parameters
Table 5-2 lists the setup parameters for the local management terminal.
Table 5-2 VT Terminal Setup
Display Setup Menu
Columns -> Controls -> Auto Wrap -> Scroll -> Text Cursor -> Cursor Style ->
General Setup Menu
Mode -> ID number -> Cursor Keys -> Power Supply ->
Communications Setup Menu
Transmit -> Receive -> XOFF -> Bits -> Parity -> Stop Bit -> Local Echo -> Port -> Transmit -> Auto Answerback ->
80 Columns Interpret Controls No Auto Wrap Jump Scroll Cursor Underline Cursor Style
VT100, 7 Bit Controls VT100ID Normal Cursor Keys UPSS DEC Supplemental
2400, 4800, 9600, 19200 Receive=Transmit XOFF at 64 8 bits No Parity 1 Stop Bit No Local Echo DEC-423, Data Leads Only Limited Transmit No Auto Answerback
Keyboard Setup Menu
Keys -> Auto Repeat -> Keyclick -> Margin Bell -> Warning Bell ->
6E123-50 and 6E133-49 User’s Guide 5-5
Typewriter Keys any option any option Margin Bell Warning Bell
Page 52
Chapter 5: Local Management
5.3.4 Telnet Connections
Once the module or chassis has a valid IP address, the user can establish a Telnet session with Local Management from any TCP/IP based node on the network. Telnet connections to the 6E123-50 and 6E133-49 require the community name passwords assigned at the SNMP Community Names screen of either the 6C105 chassis, or the module. For additional information about community names, refer to Section 5.8, SNMP
Community Names Screen. Refer to the instructions included with the
Telnet application for information about establishing a Telnet session.
5-6 6E123-50 and 6E133-49 User’s Guide
Page 53
Accessing Local Management
5.4 ACCESSING LOCAL MANAGEMENT
Access to Local Management is controlled through the Password screen,
Figure 5-3. Whenever a connection is made to the 6E123-50 and
6E133-49 the Password screen displays. Before continuing, the user must enter a password which is compared to the previously stored passwords. The level of access allowed the user depends on the password. To set or change passwords refer to Section 5.8. The following steps describe the procedure to access Local Management.
1. Turn on the terminal. Press ENTER (this may take up to four times,
because the COM port of the 6E123-50 and 6E133-49 auto-senses the baud rate of the terminal) until the 6C105 Local Management Password screen, Figure 5-3, displays.
Event Message Line
6C105 LOCAL MANAGEMENT
CABLETRON Systems, Incorporated
P.O.Box 5005
Rochester, NH 03866-5005 USA
(603) 332-9400
(c) Copyright CABLETRON Systems, Inc, 1997
Enter Password:
Figure 5-3 Local Management Password Screen
1960_12
2. Enter the Password and press ENTER. The default Super-User access
password is “public” or press ENTER.
6E123-50 and 6E133-49 User’s Guide 5-7
Page 54
Chapter 5: Local Management
The User’s password is one of the community names specified
NOTE
in the SNMP Community Names screen. Access to certain Local Management capabilities depends on the degree of access accorded that community name. Refer to Section 5.8.
If an invalid password is entered, the terminal beeps and the cursor
returns to the beginning of the password entry field.
Entering a valid password causes the associated access le vel to display
at the bottom of the screen and the Main Menu screen to appear.
If no activity occurs for several minutes, the Password screen
reappears and the session ends.
5.4.1 Navigating Local Management Screens
The 6E123-50 and 6E133-49 Local Management application consists of a series of menu screens. Navigate through Local Management by selecting items from the menu screens.
The 6E123-50 and 6E133-49 support three modes of switch operation. The switching modes are as follows:
802.1D SWITCHING, (traditional switching)
802.1Q SWITCHING, (802.1Q port based VLANs)
SECURE FAST VLAN, (Cabletron Systems SecureFast Switching)
Refer to the Release Notes shipped with the product to verify
NOTE
which screens are supported in each of the three available switching modes.
The switch operational mode may be set in either the Chassis Configuration screen (Section 5.7), or the General Configuration screen of the module (Section 5.15). Depending on the Operational Mode set for the module, the hierarchy of Local Management screens differs as shown in Figure 5-4, Figure 5-7, and Figure 5-8. Refer to the appropriate figure that relates to the Operational Mode that will be set for the module to see the applicable Local Management screen hierarchy.
5-8 6E123-50 and 6E133-49 User’s Guide
Page 55
Accessing Local Management
G
\
Password
Main Menu
Chassis Menu
Module Menu
eneral Configuration
SNMP Community Names
SNMP Traps
Chassis Environmental
Port Redirect Function
Module Configuration Menu
Module Statistics Menu
Network Tools
General Configuration
SNMP Community Names
SNMP Traps Switch Configuration
SmartTrunk Configuration
Module Specific Configuration Menu
Switch Statistics Interface Statistics
RMON Statistics Repeater Statistics
System Resources
High Speed Interface Configuration
Fast Ethernet
HSIM
Flash Download
Port Redirect
Function Broadcast Suppression
Repeater Configuration Menu
Repeater Level Security Configuration
Port Level Security Configuration
Password
Main Menu
Figure 5-4 802.1D Switching Mode, LM Screen Hierarchy
Chassis Menu
Module Menu
General Configuration
SNMP Community Names SNMP Traps Chassis Environmental
802.1Q VLAN Configuration
Module Configuration Menu
Module Statistics Menu
Network Tools
General Configuration SNMP Community Names SNMP Traps Switch Configuration
SmartTrunk Configuration
Module Specific Configuration Menu
Switch Statistics Interface Statistics
RMON Statistics
Repeater Statistics
System Resources
High Speed Interface Configuration
Flash Download
Broadcast Suppression
802.1Q VLAN Configuration
Repeater Configuration Menu
Repeater Level Security Configuration
Port Level Security Configuration
Fast Ethernet
HSIM
Figure 5-5 802.1Q Switching Mode, LM Screen Hierarchy
6E123-50 and 6E133-49 User’s Guide 5-9
Page 56
Chapter 5: Local Management
Password
Main Menu
Chassis Menu
Module Menu
General Configuration SNMP Community Names
SNMP Traps Chassis Environmental
Module Configuration Menu
Module Statistics Menu
Network Tools
General Configuration SNMP Community Names SNMP Traps
Module Specific Configuration Menu
Interface Statistics RMON Statistics Repeater Statistics
System Resources
High Speed Interface Configuration
Flash Download
Repeater Configuration Menu
Repeater Level Security Configuration
Port Level Security Configuration
Fast Ethernet
HSIM
Figure 5-6 SecureFast VLAN Mode, LM Screen Hierarchy
5.4.2 Selecting Local Management Menu Screen Items
Select items on a menu screen by performing the following steps:
1. Use the arrow keys to highlight a menu item.
2. Press ENTER. The selected menu item displays on the screen.
5.4.3 Exiting Local Management Screens
There are two ways to exit Local Management (LM).
Using the EXIT Command
To exit an LM screen using the EXIT command, proceed as follows:
1. Use the arrow keys to highlight the EXIT command at the bottom of
the Local Management screen.
2. Press ENTER. The Password screen displays and the session ends.
5-10 6E123-50 and 6E133-49 User’s Guide
Page 57
Accessing Local Management
Using the RETURN Command
1. Use the arrow keys to highlight the RETURN command at the bottom
of the Local Management screen.
2. Press ENTER. The previous screen in the Local Management
hierarchy displays.
The user can also exit Local Management screens by pressing
NOTE
ESC twice. This exit method does not warn about unsaved changes and all unsaved changes will be lost.
3. Exit from 6E123-50 and 6E133-49 Local Management by repeating
steps 1 and 2 until the Main Menu screen displays.
4. Use the arrow keys to highlight the RETURN command at the bottom
of the Main Menu screen.
5. Press ENTER. The Password screen displays and the session ends.
6E123-50 and 6E133-49 User’s Guide 5-11
Page 58
Chapter 5: Local Management
5.5 THE MAIN MENU SCREEN
The Main Menu screen is the access point for all Local Management screens for the module and the 6C105 chassis. Figure 5-7 shows the Main Menu screen.
6C105 LOCAL MANAGEMENT
Main Menu
CHASSIS
MODULES
EXIT
2269_91
Figure 5-7 Main Menu Screen
The following explains each Main Menu screen item as shown in
Figure 5-7:
CHASSIS
The CHASSIS menu item provides access to the Chassis Menu screen, shown in Figure 5-8, that is used to configure the 6C105 chassis, access current chassis power supply and environmental status, and to configure IEEE 802.1Q VLANs.
Access the Chassis Configuration screen by using the arrow keys to highlight the CHASSIS menu item and pressing ENTER. The Chassis Configuration screen displays. Proceed to Section 5.6.
5-12 6E123-50 and 6E133-49 User’s Guide
Page 59
Chassis Menu Screen
MODULES
The MODULES menu item provides access to the Module Selection screen that is used to select individual modules in the chassis for management purposes.
Access the Module Selection screen by using the arrow keys to highlight the MODULES menu item and pressing ENTER. The Module Selection screen displays. Proceed to Section 5.12.
5.6 CHASSIS MENU SCREEN
The Chassis Menu screen, Figure 5-8, provides access to Local Management screens that allow you to configure and monitor operating parameters, modify SNMP community names, set SNMP traps, monitor the 6C105 environmental status, perform port redirect functions, and to configure the 6C105 for IEEE 802.1Q operation.
6C105 LOCAL MANAGEMENT
Chassis Menu
CHASSIS CONFIGURATION
SNMP COMMUNITY NAMES SNMP TRAPS
CHASSIS ENVIRONMENTAL PORT REDIRECT FUNCTION
EXIT
RETURN
2269_99
6E123-50 and 6E133-49 User’s Guide 5-13
Figure 5-8 Chassis Menu Screen
Page 60
Chapter 5: Local Management
The following briefly explains each screen accessible from the Chassis Menu screen.
CHASSIS CONFIGURATION
The Chassis Configuration screen allows the user to configure operating parameters for the 6C105 chassis. For details, refer to Section 5.7.
SNMP COMMUNITY NAMES
The SNMP Community Names screen allows the user to enter new, change, or review the community names used as access passwords for device management operation. Access is limited based on the password level of the user. For details, refer to Section 5.8.
SNMP TRAPS
The SNMP Traps screen provides display and configuration access to the table of IP addresses used for trap destinations and associated community names. For details, refer to Section 5.9.
CHASSIS ENVIRONMENTAL
The Chassis Environmental screen provides access to chassis power supply status, power supply redundancy status and chassis f an tray status. For details, refer to Section 5.10.
PORT REDIRECT FUNCTION
The Port Redirect Function screen allows the user to redirect traffic from one or multiple modules and ports in the chassis to a specific destination module or port. For details, refer to Section 5.11.
5-14 6E123-50 and 6E133-49 User’s Guide
Page 61
Chassis Configuration Screen
5.7 CHASSIS CONFIGURATION SCREEN
The Chassis Configuration screen, Figure 5-9, allows the user to set the chassis date and time, IP address and Subnet Mask, the operational mode of all modules installed in the chassis, and to view the chassis uptime.
Access the Chassis Configuration screen from the Chassis Menu screen by using the arrow ke ys to highlight the CHASSIS CONFIGURATION menu item and pressing ENTER. The Chassis Configuration screen,
Figure 5-9, displays.
Event Message Line
6C105 LOCAL MANAGEMENT
Chassis Configuration
MAC Address: IP Address: Subnet Mask:
Operational Mode: [802.1D SWITCHING]
00-00-ID-00-00-00
000.000.000.000
000.000.000.000
EXIT
Chassis Date: Chassis Time: Screen Refresh Time: Screen Lockout Time:
Chassis Uptime XX D XX H XX M
10/11/97 14:23:00 30 sec. 15 min.
RETURNSAVE
2269_98
Figure 5-9 Chassis Configuration Screen
The following briefly explains each Chassis Configuration screen field:
MAC Address (Read-Only)
Displays the base physical address of the chassis.
6E123-50 and 6E133-49 User’s Guide 5-15
Page 62
Chapter 5: Local Management
IP Address (Modifiable)
This field allows the IP address to be set for the 6C105 chassis. If an IP address is assigned to the 6C105 chassis all the interface modules installed in the chassis can be managed via this IP address, eliminating the need to assign an IP address to each interface module. To set the IP address, refer to Section 5.7.1.
Subnet Mask (Modifiable)
When a valid IP address is assigned, the Subnet Mask field
NOTE
automatically enters the default mask that corresponds with class of IP entered in the IP Address field. Some firmware revisions do support changing the chassis subnet mask from the default value. Refer to your Release Notes to ensure that the Subnet Mask is a modifiable field.
Displays the subnet mask for the chassis. A subnet mask “masks out” the network bits of the IP address by setting the bits in the mask to 1 when the network treats the corresponding bits in the IP address as part of the network or subnetwork address, or to 0 if the corresponding bit identifies the host. The 6C105 chassis automatically uses the default subnet mask that corresponds to the IP class that was entered in the IP address field.
Section 5.7.2 describes how to change the subnet mask from the default
value.
Chassis Date (Modifiable)
Contains a value that the chassis recognizes as the current date. When the chassis date is modified and saved all interface modules installed in the chassis are set to this date. To set a new chassis date, refer to
Section 5.7.3.
Chassis Time (Modifiable)
Contains a value that the chassis recognizes as the current time. When the chassis time is modified and saved, all interface modules installed in the chassis are set to this time. To enter a new time, refer to Section 5.7.4.
Screen Refresh Time (Modifiable)
Contains the rate at which the screens are updated. This setting determines how frequently (in seconds) information is updated on the screen. To enter a new update time, refer to Section 5.7.5.
5-16 6E123-50 and 6E133-49 User’s Guide
Page 63
Chassis Configuration Screen
Screen Lockout Time (Modifiable)
Contains the maximum number of minutes that the Local Management application displays a module’s screen while awaiting input or action from a user. For example, if the number 5 is entered in this field, the user has up to five minutes to respond to each of the specified module’s Local Management screens. In this example, after five minutes of “idleness” (no input or action), the terminal “beeps” five times, the Local Management application terminates the session, and the display returns to the Password screen. To enter a new lockout time, refer to Section 5.7.6.
Chassis Uptime (Read-Only)
Displays the total time the chassis has been operating. The chassis uptime is based on which interface module installed in the chassis has been operating for the longest period of time.
Operational Mode (Toggle)
This field allows the user to set all the modules in the chassis to operate as traditional switches (802.1D SWITCHING option), or as IEEE 802.1Q switches (802.1Q SWITCHING option).
In 802.1D SWITCHING mode, the 24 ports located on the front panel, and each Fast Ethernet Interface Module, and HSIM port(s) are bridged to each other.
When the operational mode is set to 802.1Q SWITCHING, the 6E123-50 and 6E133-49 act as IEEE 802.1Q switches. The modules are able to increase their switching functionality by creating and maintaining port based Virtual LANs (VLANs).
For details on how to select the Operational Mode, refer to Section 5.7.7.
5.7.1 Setting the IP Address
To set the IP address, perform the following steps:
1. Use the arrow keys to highlight the IP Address field.
2. Enter the IP address into this field using Decimal Dotted Notation
(DDN) format. For example: 134.141.79.120
6E123-50 and 6E133-49 User’s Guide 5-17
Page 64
Chapter 5: Local Management
3. Press ENTER. If the IP address is a valid format, the cursor returns to
the beginning of the IP address field. If the entry is not valid, the Event Message Line displays “INVALID IP ADDRESS OR FORMAT ENTERED”. Local Management does not alter the current value and refreshes the IP address field with the previous value.
4. Use the arrow keys to highlight the SAVE command, then press
ENTER. The “SAVED OK” message displays indicating that the changes have been saved to memory.
5.7.2 Setting the Subnet Mask
If the management workstation that is to receive SNMP traps from the 6C105 is located on a separate subnet, the subnet mask for the 6C105 must be changed from its default.
When a valid IP address is assigned, the Subnet Mask field
NOTE
automatically enters the default mask that corresponds with class of IP entered in the IP Address field. Some firmware revisions do support changing the chassis subnet mask from the default value. Refer to your Release Notes to ensure that the Subnet Mask is a modifiable field.
To change the subnet mask from its default, perform the following steps:
1. Use the arrow keys to highlight the Subnet Mask field.
2. Enter the subnet mask into this field using Decimal Dotted Notation
(DDN) format. For example: 255.255.255.0
3. Press ENTER. If the subnet mask is valid, the cursor returns to the
beginning of the Subnet Mask field. If the entry is not valid, the Event Message Line displays “INVALID SUBNET MASK OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the Subnet Mask field with the previous value.
4. Use the arrow keys to highlight the SAVE command, then press
ENTER. The changes are saved to memory.
5-18 6E123-50 and 6E133-49 User’s Guide
Page 65
Chassis Configuration Screen
5.7.3 Setting the Chassis Date
The 6C105 is year 2000 compliant, so the Chassis Date may be set beyond the year 1999. To set the chassis date, perform the following steps:
1. Use the arrow keys to highlight the Chassis Date field.
2. Enter the date in an MM/DD/YYYY format.
It is not necessary to add separators between month, day, and
NOTE
3. Press ENTER to set the system calendar to the date in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
year numbers. For e xample , to set the date to 03/17/1997, type “03171997” in the Chassis Date field.
If the date entered is a valid format, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current value, but it does refresh the Chassis Date field with the previous value.
Upon saving the new chassis date, all interface modules
NOTE
installed in the chassis recognize the new value as the current date.
5.7.4 Setting the Chassis Time
To set the chassis clock, perform the following steps:
1. Use the arrow keys to highlight the Chassis Time field.
2. Enter the time in a 24-hour format, HH:MM:SS.
6E123-50 and 6E133-49 User’s Guide 5-19
Page 66
Chapter 5: Local Management
When entering the time in the system time field, separators
NOTE
between hours, minutes, and seconds do not need to be added as long as each entry uses two numeric characters. For example, to set the time to 6:45 A.M., type “064500” in the Chassis Time field.
3. Press ENTER to set the system clock to the time in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is a valid format, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current value and refreshes the Chassis Time field with the previous value.
Upon saving the new chassis time, all interface modules
NOTE
installed in the chassis recognize the new value as the current time.
5.7.5 Entering a New Screen Refresh Time
The screen refresh time is set from 3 to 99 seconds with a default of 3 seconds. To set a new screen refresh time, perform the following steps:
1. Use the arrow keys to highlight the Screen Refresh Time field.
2. Enter a number from 3 to 99.
3. Press ENTER to set the refresh time to the time entered in the input
field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is within the 3 to 99 seconds range, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current setting, but it does refresh the Screen Refresh Time field with the previous value.
5-20 6E123-50 and 6E133-49 User’s Guide
Page 67
Chassis Configuration Screen
5.7.6 Setting the Screen Lockout Time
The screen lockout time can be set from 1 to 30 minutes with a default of 15 minutes. To set a new lockout time, perform the following steps:
1. Use the arrow keys to highlight the Screen Lockout Time field.
2. Enter a number from 1 to 30.
3. Press ENTER to set the lockout time in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is within the 1 to 30 minutes range, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current setting, but it does refresh the Screen Lockout Time field with the previous value.
5.7.7 Setting the Operational Mode
To set the Operational Mode, proceed as follows:
1. Use arrow keys to highlight the Operational Mode field.
2. Press the SPACE bar to step to the appropriate operation mode,
(802.1D SWITCHING or 802.1Q SWITCHING).
3. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER. The following warning screen displays:
6E123-50 and 6E133-49 User’s Guide 5-21
Page 68
Chapter 5: Local Management
YOU HAVE ELECTED TO SAVE THE OPERATIONAL MODE FOR THE WHOLE CHASSIS. THIS WILL CAUSE ALL OF THE BOARDS IN THE CHASSIS TO REBOOT. ARE YOU SURE YOU WANT TO SAVE THE NEW OPERATIONAL MODE
WARNING!
NOYES
1666
Figure 5-10 Operational Mode Warning Screen
4. Use the arrow keys to highlight the YES command and press ENTER.
The changes are saved, and all the modules installed in the chassis reboot.
If the 6E123-50 and 6E133-49 have been set to 802.1Q
NOTE
SWITCHING, refer to your
Port Based VLAN User’s Guide
to
configure the devices for this type of operation. The Operational Mode field in the Chassis Configuration
screen does not support the SECURE FAST VLAN operational mode. For the modules to function as SecureFast switches, they must have a unique IP addresses, and be configured to act as Standalone devices in terms of Local Management via the 6C105 chassis. Section 5.15.9 provides additional instructions and rules that must be met before configuring the modules as SecureFast switches.
5-22 6E123-50 and 6E133-49 User’s Guide
Page 69
SNMP Community Names Screen
5.8 SNMP COMMUNITY NAMES SCREEN
The SNMP Community Names menu item allows the user to set Local Management community names. Community names act as passwords to Local/Remote Management and provide security access to the 6C105. Access to the 6C105 is controlled by enacting any of three different le v els of security authorization (read-only, read-write, and super-user).
Super-User access gives the user full management privileges,
NOTE
Access the SNMP Community Names screen from the Chassis Menu screen by using the arrow keys to highlight the SNMP COMMUNITY NAMES menu item and pressing ENTER. The SNMP Community Names screen, Figure 5-11, displays.
allows existing passwords to be changed, and all modifiable MIB objects for the Cabletron Container MIB and Internet MIB-II to be edited.
Event Message Line
6C105 LOCAL MANAGEMENT
SNMP Community Names
Community Name
public
public public
EXIT
Access Policy read-only read-write super-user
RETURNSAVE
1960_97
Figure 5-11 SNMP Community Names Screen
6E123-50 and 6E133-49 User’s Guide 5-23
Page 70
Chapter 5: Local Management
The following explains each SNMP Community Names screen field:
Community Name (Modifiable)
Displays the user-defined name through which a user accesses 6C105 management. Any community name assigned here acts as a password to Local/Remote Management.
Access Policy (Read-Only)
Indicates the access accorded each community name. Possible selections are as follows:
read-only This community name allows read-only access
to the 6C105 MIB objects, and excludes access to security-protected fields of read-write or super-user authorization.
read-write This community name allows read and write
access to the 6C105 MIB objects, excluding security protected fields for super-user access only.
super-user This community name permits read-write
access to the 6C105
MIB objects and allows the
user to change all modifiable parameters including community names, IP addresses, traps, and SNMP objects.
5.8.1 Establishing Community Names
The password used to access Local Management at the Password screen must have Super-User access in order to view and edit the SNMP Community Names screen. Using a password with read-only or read-write access does not allow the user to view or edit the SNMP Community Names screen.
5-24 6E123-50 and 6E133-49 User’s Guide
Page 71
SNMP Community Names Screen
Any community name assigned in the SNMP Community
NOTE
NOTE
Names screen is a password to its corresponding level of access to Local Management. The community name assigned Super-User access is the only one that gives the user complete access to Local Management.
All passwords assigned in the 6C105 SNMP Community Names screen allow access to both the 6C105 Local Management screens, and the Local Management screens of the interface modules that are installed in the chassis. To configure the interface module to not allow access to the 6C105 Local Management screens refer to Section 5.16.
To establish community names, proceed as follows:
1. Use the arrow keys to highlight the Community Name field adjacent
to the selected access level.
2. Enter the password in the field (maximum 31 characters).
3. Press ENTER.
4. Repeat steps 1 through 3 to modify the other community names.
5. Use the arrow keys to highlight SAVE at the bottom of the screen and
press ENTER. The message “SAVED OK” displays. The community names are saved to memory and their access modes implemented.
6E123-50 and 6E133-49 User’s Guide 5-25
Page 72
Chapter 5: Local Management
5.9 SNMP TRAPS SCREEN
Since the 6C105 is an SNMP compliant device, it can send messages to multiple Network Management Stations to alert users of status changes. The SNMP Traps screen is shown in Figure 5-12.
Access the SNMP Traps screen from the Chassis Menu screen by using the arrow keys to highlight the SNMP TRAPS menu item and pressing ENTER. The Chassis SNMP Traps screen displays.
Event Message Line
6C105 LOCAL MANAGEMENT
Chassis SNMP Traps
Trap Destination
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Trap Community Name
public public public public public public public public
EXIT
Enable Traps
[YES] [YES] [YES] [YES] [YES] [YES] [YES] [YES]
RETURNSAVE
2269_96
Figure 5-12 Chassis SNMP Traps Screen
The following explains each field of the SNMP Traps screen.
Trap Destination (Modifiable)
Indicates the IP address of the workstation to receive trap alarms. Up to eight different destinations can be defined.
Trap Community Name (Modifiable)
Displays the Community Name included in the trap message sent to the Network Management Station with the associated IP address.
5-26 6E123-50 and 6E133-49 User’s Guide
Page 73
SNMP T raps Screen
Enable Traps (Toggle)
Enables transmission of the traps to the network management station with the associated IP address. This field toggles between YES and NO.
5.9.1 Configuring the Trap Table
To configure the Trap table, proceed as follows:
1. Using the arrow keys, highlight the appropriate Trap Destination
field.
2. Enter the IP Address of the workstation that is to receive traps. IP
address entries must follow the DDN format. For example: 134.141.79.121
3. Press ENTER. If an invalid entry is entered “INVALID IP
ENTERED” is displayed in the Event Message Line.
4. Using the arrow keys, highlight the Trap Community Name field.
Enter the community name.
5. Press ENTER.
6. Using the arrow keys, highlight the Enable Traps field. Press the
SPACE bar to choose either YES (send alarms from the chassis to the workstation), or NO (prevent alarms from being sent).
7. Using the arrow keys, highlight the SAVE command and press
ENTER. The message “SAVED OK” displays on the screen.
Exiting without saving causes a “NOT SAVED?” message to
NOTE
appear above the SAVE command. Edits will be lost if they are not saved before exiting.
The designated workstations now receive traps from the 6C105.
6E123-50 and 6E133-49 User’s Guide 5-27
Page 74
Chapter 5: Local Management
5.10 CHASSIS ENVIRONMENTAL SCREEN
The Chassis Environmental menu item allows the user to view chassis environmental information.
Access the Chassis Environmental Information screen from the Chassis Menu screen by using the arrow keys to highlight the CHASSIS ENVIRONMENTAL menu item and pressing ENTER. The Chassis Environmental Information screen, Figure 5-13, displays.
6C105 LOCAL MANAGEMENT
Chassis Environmental Information
Chassis Power Redundancy Power Supply #1 Status Power Supply #2 Status Chassis Fan Status
EXIT
Not Available Normal Not Installed Normal
RETURN
1960_94
Figure 5-13 Chassis Environmental Information Screen
The following describes each of the Chassis Environmental Information screen fields.
Chassis Power Redundancy (Read-Only)
Displays the current redundancy status of the 6C105 power supplies. This field will read either “Available” or “Not Available”.
Power Supply #X Status (Read-Only)
Displays the current status of power supplies 1 and 2 for the 6C105. This field will read either “Normal”, “Fault”, or “Not Installed”.
Chassis Fan Status (Read-Only)
Displays the current status of the 6C105 fan tray. This field will read either “Normal”, “Fault”, or “Not Installed”.
5-28 6E123-50 and 6E133-49 User’s Guide
Page 75
Port Redirect Function Screen
5.11 PORT REDIRECT FUNCTION SCREEN
The Port Redirect Function screen may not be available
NOTE
The Port Redirect Function screen, Figure 5-14, allows the user to set each one of the modules in the chassis (1 through 5), and the ports of the corresponding module installed, as a source or destination port. A port can be set to have one or more destination ports and chassis module slot numbers. For example, port 1 in module (slot) 1 can be set as a source port with three destinations, ports 2, 3, and 4 in module (slot) 3. Traffic from port 1 in module 1 is then automatically redirected to ports 2, 3, and 4 in module 3. Port 1 in module 1 can also serve as a destination port for other ports and modules. The port redirect function is extremely useful for troubleshooting purposes, as it allows traffic to be sent to a particular port(s) where, with the use of an analyzer or RMON probe, all current traffic from the source port(s) can be examined.
depending on the operational mode that has been set for the chassis. Refer to your Release Notes to see what operational modes support the Port Redirect Function. Refer to
Section 5.7.7, Setting the Operational Mode, for instructions
on configuring the operational mode of all the modules installed in the chassis.
NOTES
The module number corresponds to the slot number in which the module resides in the 6C105 chassis (1 through 5).
Although traffic from the source port (including, if desired, errored frames) is sent to the destination port, normal switching is still performed for all frames on the source port.
Access the Port Redirect Function screen from the Chassis Menu screen by using the arrow keys to highlight the PORT REDIRECT FUNCTION menu item and pressing ENTER. The Port Redirect Function screen, Figure 5-14, displays.
6E123-50 and 6E133-49 User’s Guide 5-29
Page 76
Chapter 5: Local Management
Event Message Line
6C105 LOCAL MANAGEMENT
Source Destination Remap Errors
============ ============ ============
Module 1 1 1 2 2 3 3 3
Port 1 1 1 2 2 3 3 3
Port Redirect Function
Module 3 3 3 1 3 4 5 5
Port 2 3 4 1 3 4 5 8
ON ON ON OFF ON ON ON OFF
Status [ADD] Errors [ON]
RETURN RETURN
2269_66
SAVE
Source Port [1] Source Module [1]
EXIT
Destination Port [1] Destination Module [1]
NEXT
PREVIOUS
Figure 5-14 Port Redirect Function Screen
The following definitions briefly explain each field of the Port Redirect Function screen.
Source Module (Read-Only)
Displays which modules are currently set as source modules.
Source Port (Read-Only)
Displays which ports are currently set as source ports.
Destination Module (Read-Only)
Displays which modules are currently set as destination modules.
Destination Port (Read-Only)
Displays which ports are currently set as destination ports.
Remap Errors (Read-only)
Displays whether the corresponding source modules and ports are configured to send errored frames to the destination modules and ports, or to drop all errored frames before forwarding traffic.
Source Module [n] (Selectable)
Allows a selected module [n] to be configured as a source module.
Source Port [n] (Selectable)
Allows a selected port [n] to be configured as a source port.
5-30 6E123-50 and 6E133-49 User’s Guide
Page 77
Port Redirect Function Screen
Destination Module [n] (Selectable)
Allows a selected module [n] to be configured as a destination module.
Destination Port [n] (Selectable)
Allows a selected port [n] to be configured as a destination port.
Errors (Toggle)
Allows the user to configure the source modules and ports to either send errored frames to selected destination modules and ports (ON option), or to drop errored frames, and send only valid traffic to the destination modules and ports (OFF option). The default setting of this field is ON.
Status (Toggle)
Allows the user to add or delete the source/destination modules and ports selected in the Source/Destination Modules and ports fields.
5.11.1 Displaying the Source and Destination Entries
There can be more than one Port Redirect Function screen depending on the number of port redirect entries. Each screen displays up to ten port redirect entries. If there is more than one screen of redirect entries, the NEXT and/or PREVIOUS command is displayed at the bottom of the screen, allowing the user to navigate to the next or previous screen.
To display the next screen, use the arrow keys to highlight NEXT. Press ENTER and the next screen of entries is displayed.
To display the previous screen, use the arrow keys to highlight PREVIOUS. Press ENTER to view the entries in the previous screen.
5.11.2 Changing Source and Destination Ports
Add or delete source/destination module and port entries as follows:
1. Use the arrow keys to highlight the Source Module field.
2. Press the SPACE bar or BACKSPACE one or more times to increment
or decrement the module number displayed in the brackets [n] until the appropriate module number is displayed.
3. Use the arrow keys to highlight the Source Port field.
6E123-50 and 6E133-49 User’s Guide 5-31
Page 78
Chapter 5: Local Management
4. Press the SPACE bar or BACKSPACE one or more times to increment
or decrement the port number displayed in the brackets [n] until the appropriate port number is displayed.
5. Use the arrow keys to highlight the Destination Module field.
6. Use the SPACE bar or BACKSPACE to step to the appropriate
module number for the destination module.
7. Use the arrow keys to highlight the Destination Port field.
8. Use the SPACE bar or BACKSPACE to step to the appropriate port
number for the destination port.
9. Use the arrow keys to highlight the Status field.
10. Use the SPACE bar to select either the ADD or DEL (delete) option.
Press ENTER. This adds or deletes the selections made in steps 2 and 4 and also updates the screen Source Module, Source Port, Destination Module and Destination Port lists.
11. Use the arrow keys to highlight the Errors field.
12. Use the SPACE bar to select either the ON or OFF option and press
ENTER. ON forces the source module and port to forward errored frames to the destination module(s) and port(s). OFF forces the errored frames to be dropped before forwarding traffic.
If more than one module and port is to be redirected, repeat
NOTE
steps 1 through 12 for each additional setting, then go to step 13 to save all the new settings at once.
13. Use the arrow keys to highlight SAVE at the bottom of the screen.
Press ENTER. The message “SAVED OK” is displayed.
5-32 6E123-50 and 6E133-49 User’s Guide
Page 79
Module Selection Screen
5.12 MODULE SELECTION SCREEN
The Module Selection screen is the access point to Local Management for all modules installed in the SmartSwitch 6000 chassis. By selecting a module, the Module Menu for the selected device displays. Figure 5-15 shows the Module Selection screen.
6E122-26 LOCAL MANAGEMENT
Module Selection
Module #
<1>
2 3 4 5
Module Type
6E123-50 6E132-25 6E123-26 6E122-26
Serial #
123456789 123456789 123456789 123456789
EXIT
Hardware Revision
XXX XXX XXX XXX
RETURN
2269-39
Figure 5-15 Module Selection Screen
The following explains each Module Selection screen field as shown in
Figure 5-15.
Module #
The Module # field displays the slot in which the module is installed. The module number enclosed in < > characters indicates the module to which the management terminal or Telnet session is connected.
Module T ype
The Module Type field displays the type of interface module that is installed in each slot.
Serial #
Indicates the serial number of the module. The serial number of the device is necessary when calling the Cabletron Systems Global Call Center.
6E123-50 and 6E133-49 User’s Guide 5-33
Page 80
Chapter 5: Local Management
Hardware Revision
Reflects the hardware version of the module.
5.12.1 Selecting a Module
To select an individual module to perform Local Management functions, proceed as follows:
1. Use the arrow keys to highlight the desired module number in the
Module # field.
2. Press ENTER, the applicable Module Menu screen displays. Proceed
to Section 5.13.
5-34 6E123-50 and 6E133-49 User’s Guide
Page 81
Module Menu Screen
5.13 MODULE MENU SCREEN
The Local Management screens shown in this chapter are for
NOTE
The 6E123-50 and 6E133-49 Module Menu screens are the access point for all Local Management screens for the 6E123-50 and 6E133-49.
Figure 5-16 shows the 6E123-50 Module Menu screen.
the 6E123-50. The 6E133-49 shares most of the following Local Management screens. All Local Management functions specific to any interface module are preceded b y a note to alert the reader.
6E123-50 LOCAL MANAGEMENT
Module Menu
Module Type: 6E123-50 Slot Number:
X
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
MODULE CONFIGURATION
MODULE STATISTICS NETWORK TOOLS
EXIT
Figure 5-16 Module Menu Screen
RETURN
2269_13
6E123-50 and 6E133-49 User’s Guide 5-35
Page 82
Chapter 5: Local Management
The following explains each Module Menu screen field as shown in
Figure 5-16:
MODULE CONFIGURATION
The Module Configuration screen provides access to the Local Management screens that are used to configure the 6E123-50 and 6E133-49. The Module Specific Configuration Menu screen provides access to the screens that allow the user to check 6E123-50 and 6E133-49 resources and set operating parameters specific to each port. For details about the Module Configuration Menu screen, refer to Section 5.14. For details about the Module Specific Configuration Menu screen, refer to
Section 5.19.
MODULE STATISTICS
The Module Statistics screen provides statistics and performance information for the 6E123-50 and 6E133-49. For details about this screen, refer to Section 5.28.
NETWORK T OOLS
The Network Tools function resides on the 6E123-50 and 6E133-49 and consists of a series of commands that allow the user to access and manage network devices. Section 5.33 explains how to use the Network Tools utility.
5-36 6E123-50 and 6E133-49 User’s Guide
Page 83
Module Configuration Menu Screen
5.14 MODULE CONFIGURATION MENU SCREEN
The Module Configuration Menu screen, Figure 5-17, provides access to Local Management screens that allow you to configure and monitor operating parameters, modify SNMP community names, set SNMP traps, configure switch parameters and configure 6E123-50 and 6E133-49 ports.
The following menu items on the Module Configuration Menu
NOTE
screen may not display if the operational mode of the module has been set to SECURE FAST VLAN:
SWITCH CONFIGURATION SMARTTRUNK CONFIGURATION
Refer to your Release Notes to see if the functionality provided by the above screens is supported in SECURE FAST VLAN mode.
Section 5.15.9 provides instructions on setting the operational
mode.
Access the Module Configuration Menu screen from the Module Menu screen by using the arrow keys to highlight the MODULE CONFIGURATION menu item and pressing ENTER. The Module Configuration screen displays.
6E123-50 and 6E133-49 User’s Guide 5-37
Page 84
Chapter 5: Local Management
6E123-50 LOCAL MANAGEMENT
Module Configuration Menu
Module Type: 6E123-50 Slot Number:
X
GENERAL CONFIGURATION
SNMP COMMUNITY NAMES SNMP TRAPS SWITCH CONFIGURATION SMARTTRUNK CONFIGURATION MODULE SPECIFIC CONFIGURATION
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
RETURNEXIT
2269_42
Figure 5-17 Module Configuration Menu Screen
The following briefly explains each screen accessible from the Module Configuration Menu screen:
GENERAL CONFIGURATION
The General Configuration screen allows the user to monitor and configure operating parameters for the 6E123-50 and 6E133-49. For details, refer to Section 5.15.
SNMP COMMUNITY NAMES
The SNMP Community Names screen allows the user to enter new, change, or review the community names used as access passwords for Local/Remote management operation. Access is limited based on the password level of the user. For details, refer to Section 5.16.
SNMP TRAPS
The SNMP Traps screen provides display and configuration access to the table of IP addresses used for trap destinations and associated community names. For details, refer to Section 5.17.
5-38 6E123-50 and 6E133-49 User’s Guide
Page 85
Module Configuration Menu Screen
SWITCH CONFIGURATION
The Switch Configuration screen provides basic setup options for modifying the switching functions of the modules. For details, refer to
Section 5.18.
SMARTTRUNK CONFIGURATION
The SmartTrunk Configuration screen allows the user to logically group interfaces to aggregate high speed uplinks. Refer to the Cabletron Systems SmartTrunk User’s Guide for additional information.
MODULE SPECIFIC CONFIGURATION
The Module Specific Configuration Menu screen allows the user to configure ports or check system resources specific to the 6E123-50 and 6E133-49. For details, refer to Section 5.19.
6E123-50 and 6E133-49 User’s Guide 5-39
Page 86
Chapter 5: Local Management
5.15 GENERAL CONFIGURATION SCREEN
The General Configuration screen, Figure 5-18, allows the user to set the system date and time, IP address and subnet mask, the default gateway, the TFTP Gateway IP address, the Operational Mode, the Management Mode, and the COM port configuration. The General Configuration screen also allows the user to Clear NVRAM, and enable or disable IP Fragmentation.
Access the General Configuration screen from the Module Configuration Menu screen by using the arrow keys to highlight the GENERAL CONFIGURATION menu item and pressing ENTER. The General Configuration screen, Figure 5-18, displays.
Event Message Line
6E123-50 LOCAL MANAGEMENT
General Configuration
Module Type: 6E123-50 Slot Number:
X
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
MAC Address: IP Address: Subnet Mask: Default Gateway: TFTP Gateway IP Addr:
Operational Mode: [802.1D SWITCHING] Management Mode: [DISTRIBUTED]
Com: [ENABLED] Application: [LM]
Clear NVRAM [NO]
00-00-ID-00-00-00
0.0.0.0
255.255.0.0 NONE DEFINED
0.0.0.0
IP Fragmentation [ENABLED]
EXIT
Module Date: Module Time: Screen Refresh Time: Screen Lockout Time: Module Uptime XX D XX H XX M
10/11/97 14:23:00 30 sec. 15 min.
RETURNSAVE
2269_15
Figure 5-18 General Configuration Screen
The following briefly explains each General Configuration screen field:
MAC Address (Read-Only)
Displays the base physical address of the module.
5-40 6E123-50 and 6E133-49 User’s Guide
Page 87
General Configuration Screen
IP Address (Modifiable)
This field allows the IP address to be set for the 6E123-50 and 6E133-49. To set the IP address, refer to Section 5.15.1.
Subnet Mask (Modifiable)
Displays the subnet mask for the module. A subnet mask “masks out” the network bits of the IP address by setting the bits in the mask to 1 when the network treats the corresponding bits in the IP address as part of the network or subnetwork address, or to 0 if the corresponding bit identifies the host. When an IP address is entered in the IP Address field, the subnet mask field automatically enters the default subnet mask for the IP address. For details about how to change the subnet mask from its default value, refer to Section 5.15.2.
Default Gateway (Modifiable)
Displays the default gateway for the 6E123-50 and 6E133-49. This field is not defined until an appropriate value is entered. For details about why and how to set the Default Gateway, refer to Section 5.15.3.
TFTP Gateway IP Addr (Modifiable)
Displays and allows the user to set the TFTP Gateway IP address for the 6E123-50 and 6E133-49. To set the TFTP Gateway IP address, refer to
Section 5.15.4.
Module Date (Modifiable)
Contains a value that the module recognizes as the current date. To set a new module date, refer to Section 5.15.5.
Module Time (Modifiable)
Contains a value that the module recognizes as the current time. To enter a new time, refer to Section 5.15.6.
Screen Refresh Time (Modifiable)
Contains the rate at which the screens are updated. This setting determines how frequently (in seconds) information is updated on the screen. To enter a new update time, refer to Section 5.15.7.
6E123-50 and 6E133-49 User’s Guide 5-41
Page 88
Chapter 5: Local Management
Screen Lockout Time (Modifiable)
Contains the maximum number of minutes that the Local Management application displays a module’s screen while awaiting input or action from a user. For example, if the number 5 is entered in this field, the user has up to five minutes to respond to each of the specified module’s Local Management screens. In this example, after five minutes of “idleness” (no input or action), the terminal “beeps” five times, the Local Management application terminates the session, and the display returns to the Password screen. To enter a new lockout time, refer to Section 5.15.8.
Module Uptime (Read-Only)
Displays the total time that the module has been operating.
Operational Mode (Selectable)
This field allows the user to set the 6E123-50 and 6E133-49 to operate as an IEEE 802.1D switch (802.1D SWITCHING option), an IEEE 802.1Q switch (802.1Q SWITCHING option), or as a Cabletron Systems SecureFast switch (SECURE FAST VLAN option).
In 802.1D SWITCHING mode, the 24 ports located on the front panel, and each Fast Ethernet Interface Module, and HSIM port(s) are bridged to each other.
In 802.1Q SWITCHING mode, the 6E123-50 and 6E133-49 are able to increase their switching functionality by creating and maintaining IEEE port based VLANs.
When the operational mode is set to SECURE FAST VLAN, the 6E123-50 and 6E133-49 act as SecureFast switches. With the Cabletron Systems VLAN Manager software, the modules are able to increase their switching functionality by creating and maintaining Virtual LANs (VLANs).
For details on how to select the Operational Mode, refer to Section 5.15.9.
Management Mode (Toggle)
This field toggles between DISTRIBUTED and STAND ALONE. In DISTRIBUTED mode, Local Management is entered via the 6C105
password screen, and all chassis configuration screens are av ailable to the user. All other modules installed in the chassis that are set for distributed management may also be accessed via a connection to a single COM port on one of the modules.
5-42 6E123-50 and 6E133-49 User’s Guide
Page 89
General Configuration Screen
If the user is establishing a remote connection, such as a Telnet
NOTE
or SNMP connection, using the IP address of the module, the chassis LM screens will not be availab le . To access the chassis LM screens, the IP address of the chassis must be used to establish the connection.
In STAND ALONE mode, the module is isolated from the chassis configuration screens, and the module may not be accessed from a module that is in DISTRIBUTED mode. This provides additional security for an y module to which the user may wish to restrict access.
Section 5.15.10
describes how to set the Management Mode.
Com (Toggle)
This field allows the user to enable or disable the COM port. The selection toggles between ENABLED and DISABLED. The default is ENABLED. For details about setting up the COM port, refer to
Section 5.15.11.
Application (Toggle)
Displays the application set for the COM port. This field allows you to set the application that the COM port will support, which includes:
Local Management (LM) via a terminal or modem connection
Uninterruptible Power Supply (UPS)
The UPS setting allows you to use the COM port to monitor an American Power Conversion Uninterruptible Power Supply (UPS). For UPS, the baud rate is automatically set to 2400.
The baud rate setting for LM is automatically sensed. For details about how to configure the COM port for v arious applications,
refer to Section 5.15.11.
6E123-50 and 6E133-49 User’s Guide 5-43
Page 90
Chapter 5: Local Management
Clear NVRAM (Toggle)
This allows the user to reset NVRAM to the factory default settings. All user-entered parameters, such as IP address and Community Names are then replaced with 6E123-50 and 6E133-49 default configuration settings. For details, refer to Section 5.15.13.
IP Fragmentation (Toggle)
This field allows the user to enable or disable IP fragmentation. The default setting for this field is ENABLED. If the 6E12X-26 or 6E13X-25 will be bridged to an FDDI ring, IP Fragmentation should be enabled. If IP Fragmentation is disabled, all FDDI frames that exceed the maximum Ethernet frame size will be discarded. For details on enabling or disabling IP Fragmentation refer to Section 5.15.14.
5.15.1 Setting the IP Address
To set the IP address, perform the following steps:
If the 6C105 chassis has been assigned an IP address, it is not
NOTE
necessary to assign an IP address to the 6E123-50 and 6E133-49. All installed modules have the same IP address as the chassis. If a separate IP address for the module is desired, proceed as follows.
1. Use the arrow keys to highlight the IP Address field.
2. Enter the IP address into this field using Decimal Dotted Notation
(DDN) format. For example: 134.141.79.120
3. Press ENTER. If the IP address is a valid format, the cursor returns to
the beginning of the IP address field. If the entry is not valid, the Event Message Line displays “INVALID IP ADDRESS OR FORMAT ENTERED”. Local Management does not alter the current value and refreshes the IP address field with the previous value.
4. Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown in Figure 5-19 displays.
5-44 6E123-50 and 6E133-49 User’s Guide
Page 91
General Configuration Screen
WARNING!
YOU HAVE ELECTED TO SAVE ONE OR MORE CONFIGURATION ITEMS THAT REQUIRE RESETTING THIS MODULE.
ARE YOU SURE YOU WANT TO CONTINUE?
YES
Figure 5-19 Configuration Warning Screen
NO
174252
5. Use the arrow keys to highlight the YES command and Press ENTER.
The changes are saved and the module reboots.
5.15.2 Setting the Subnet Mask
If the management workstation that is to receive SNMP traps from the 6E123-50 and 6E133-49 is located on a separate subnet, the subnet mask for the 6E123-50 and 6E133-49 must be changed from its default.
To change the subnet mask from its default, perform the following steps:
1. Use the arrow keys to highlight the Subnet Mask field.
2. Enter the subnet mask into this field using Decimal Dotted Notation
(DDN) format. For example: 255.255.255.0
6E123-50 and 6E133-49 User’s Guide 5-45
Page 92
Chapter 5: Local Management
3. Press ENTER. If the subnet mask is valid, the cursor returns to the
beginning of the Subnet Mask field. If the entry is not valid, the Event Message Line displays “INVALID SUBNET MASK OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the Subnet Mask field with the previous value.
4. Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown in Figure 5-19 displays.
5. Use the arrow keys to highlight the YES command and press ENTER.
The changes are saved and the module reboots.
5.15.3 Setting the Default Gateway
If the SNMP management station is located on a different IP subnet than the 6E123-50 and 6E133-49, a default gateway must be specified. When an SNMP Trap is generated, the 6E123-50 and 6E133-49 sends the Trap to the default gateway. To set the default gateway, perform the following steps:
1. Use the arrow keys to highlight the Default Gateway field.
2. Enter the IP address of the default gateway using the DDN format.
For example: 134.141.79.121
3. Press ENTER. If the default gateway entered is a valid format, the
cursor returns to the beginning of the Default Gateway field. If the entry is not valid, the Event Message Line displays “INVALID DEFAULT GATEWAY OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the Default Gateway field with the previous value.
4. Use the arrow keys to highlight the SAVE command.
5. Press ENTER. The Event Message Line at the top of the screen
displays “SAVED OK”.
5-46 6E123-50 and 6E133-49 User’s Guide
Page 93
General Configuration Screen
5.15.4 Setting the TFTP Gateway IP Address
If the network TFTP server is located on a different IP subnet than the 6E123-50 and 6E133-49, a Gateway IP address should be specified. To set the TFTP Gateway IP address, perform the following steps:
1. Use the arrow keys to highlight the TFTP Gateway IP Address field.
2. Enter the IP address of the TFTP gateway using the DDN format.
For example: 134.141.80.122
3. Press ENTER. If the TFTP gateway IP address entered is a valid
format, the cursor returns to the beginning of the TFTP Gateway IP Address field. If the entry is not valid, the Event Message Line displays “INVALID TFTP GATEWAY IP ADDRESS OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the TFTP Gateway IP Address field with the previous value.
4. Use the arrow keys to highlight the SAVE command.
5. Press ENTER. The Event Message Line at the top of the screen
displays “SAVED OK”.
5.15.5 Setting the Module Date
The modules are year 2000 compliant, so the module date may be set beyond the year 1999. To set the module date, perform the following steps:
If the 6C105 chassis has been assigned a chassis date, it is not
NOTE
1. Use the arrow keys to highlight the Module Date field.
2. Enter the date in an MM/DD/YYYY format.
necessary to assign a module date to the 6E123-50 and 6E133-49. All installed modules recognize the chassis date of the 6C105.
It is not necessary to add separators between month, day, and
NOTE
year numbers. For e xample , to set the date to 03/17/1997, type “03171997” in the Module Date field.
3. Press ENTER to set the system calendar to the date in the input field.
6E123-50 and 6E133-49 User’s Guide 5-47
Page 94
Chapter 5: Local Management
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the date entered is a valid format, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current value, but it does refresh the Module Date field with the previous value.
5.15.6 Setting the Module Time
To set the module clock, perform the following steps:
If the 6C105 chassis has been assigned a chassis time, it is not
NOTE
necessary to assign a module time to the 6E123-50 and 6E133-49. All installed modules recognize the chassis time of the 6C105.
1. Use the arrow keys to highlight the Module Time field.
2. Enter the time in an 24-hour format, HH:MM:SS.
When entering the time in the system time field, separators
NOTE
between hours, minutes, and seconds do not need to be added as long as each entry uses two numeric characters. For example, to set the time to 6:45 A.M., type “064500” in the Module Time field.
3. Press ENTER to set the system clock to the time in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is a valid format, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current value and refreshes the Module Time field with the previous value.
5.15.7 Entering a New Screen Refresh Time
The screen refresh time is set from 3 to 99 seconds with a default of 3 seconds. To set a new screen refresh time, perform the following steps:
1. Use the arrow keys to highlight the Screen Refresh Time field.
5-48 6E123-50 and 6E133-49 User’s Guide
Page 95
General Configuration Screen
2. Enter a number from 3 to 99.
3. Press ENTER to set the refresh time to the time entered in the input
field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is within the 3 to 99 seconds range, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current setting, but it does refresh the Screen Refresh Time field with the previous value.
5.15.8 Setting the Screen Lockout Time
The screen lockout time can be set from 1 to 30 minutes with a default of 15 minutes. To set a new lockout time, perform the following steps:
1. Use the arrow keys to highlight the Screen Lockout Time field.
2. Enter a number from 1 to 30.
3. Press ENTER to set the lockout time in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is within the 1 to 30 minutes range, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current setting, but it does refresh the Screen Lockout Time field with the previous value.
6E123-50 and 6E133-49 User’s Guide 5-49
Page 96
Chapter 5: Local Management
5.15.9 Setting the Operational Mode
Before setting the operational mode, ensure that the items
!
CAUTION
contained in this caution are fully understood. If the module will be configured to operate as a SecureFast
switch the following procedures should be performed before setting the operational mode:
The module must be assigned a unique IP address. The Management Mode of the module will automatically be set
to STANDALONE. The Management Mode field will no longer display on the General Configuration screen, and the module will no longer support Chassis configuration and Module selection screens. If the module will be a SecureFast switch, distributed management is not allowed.
The module has been assigned SNMP community names from the module SNMP Community Names screen (Section 5.16). In Standalone management mode, the module does not use the community names of the 6C105 chassis.
To set the Operational Mode, proceed as follows:
1. Use arrow keys to highlight the Operational Mode field.
2. Press the SPACE bar to step to the appropriate operation mode,
(802.1D SWITCHING, 802.1Q SWITCHING, or SECURE FAST VLAN).
3. Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown in Figure 5-19 displays.
4. Use the arrow keys to highlight the YES command and press ENTER.
The changes are saved and the module reboots.
Upon saving the new operational mode, the module will reboot.
NOTE
If the 6E123-50 and 6E133-49 have been set to 802.1Q SWITCHING, refer to your
configure the devices for this type of operation.
Port Based VLAN User’s Guide
to
If the 6E123-50 and 6E133-49 have been set to SECURE F AST VLAN, refer to your SecureFast documentation set to configure the devices for this type of operation.
5-50 6E123-50 and 6E133-49 User’s Guide
Page 97
General Configuration Screen
5.15.10 Setting the Management Mode
To set the management mode, perform the following steps:
Upon saving the new Management Mode, the module will
NOTE
1. Use the arrow keys to highlight the Management Mode field:
reboot. If the module will be set to STAND ALONE, ensure the f ollowing
procedures have been completed: The module has been assigned a unique IP address. The module has been assigned SNMP community names from
the module SNMP Community Names screen (Section 5.16). In STAND ALONE management mode, the module does not use the community names of the 6C105 chassis.
2. Use the SPACE bar to toggle the options (DISTRIBUTED or
STAND ALONE) until the desired mode displays.
3. Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown in Figure 5-19 displays.
4. Use the arrow keys to highlight the YES command and press ENTER.
The changes are saved and the module reboots.
5.15.11 Configuring the COM Port
Before altering the COM port settings, ensure that a valid IP
!
CAUTION
The 6E123-50 and 6E133-49 COM ports support the following applications:
address is set for the module or chassis. (Refer to
Section 5.15.1, Setting the IP Address.) Read this entire
COM port configuration section before changing the settings of the COM port.
Refer to the Release Notes included with the 6E123-50 and
NOTE
6E133-49 to verify which COM Port applications are currently supported.
Local Management connections
6E123-50 and 6E133-49 User’s Guide 5-51
Page 98
Chapter 5: Local Management
American Power Conversion Uninterruptible Power Supply (UPS)
connections
To configure the COM port, proceed as follows:
1. Use the arrow keys to highlight the Com field.
Do NOT disable or alter the settings of the COM port while
!
CAUTION
operating the current Local Management connection through a terminal. Altering the COM port settings disconnects the Local Management terminal from the port, and ends the Local Management session.
2. Press the SPACE bar to choose either ENABLED or DISABLED.
The COM port must be ENABLED if it will be used for Local Management or UPS applications. Select DISABLED if you wish to disable the COM port for additional module security.
If the COM port is reconfigured without a valid IP address set
!
CAUTION
on the module or chassis, the message shown in Figure 5-20 displays. Do not continue unless the outcome of the action is fully understood.
WARNING
THE COM PORT HAS BEEN RECONFIGURED AND THERE IS NO IP ADDRESS SET FOR THIS DEVICE. YOU WILL NO LONGER BE ABLE TO MANAGE THIS BOARD. DO YOU STILL WISH TO RECONFIGURE THIS COM PORT?
YES
Figure 5-20 COM Port Warning Screen
5-52 6E123-50 and 6E133-49 User’s Guide
NO
174252
Page 99
General Configuration Screen
If the 6C105 chassis has been configured with a valid IP
NOTE
address this screen will not appear. When the chassis is assigned a valid IP address all the interface modules installed share this same address.
3. Use the arrow keys to highlight YES. Press ENTER.
4. If you ENABLED the port, proceed to Section 5.15.12. If you
DISABLED the port, use the arrow keys to highlight SAVE at the
bottom of the screen, then press ENTER. When the message “SAVED OK” displays, the edits are saved.
Exiting without saving causes the message “NOT SAVED --
!
CAUTION
PRESS SAVE T O KEEP CHANGES” to appear. Exiting without saving causes all edits to be lost.
5.15.12 Changing the Com Port Application
After enabling the COM port as described in Section 5.15.11, you can select one of the applications supported by the COM port: LM, and UPS. The default application is LM.
To change the COM port application:
1. Use the arrows keys to highlight the Application field.
2. Use the SPACE bar or BACKSPACE to step through the available
settings until the operation you require appears. Table 5-3 lists the available settings and their corresponding applications.
Table 5-3. COM Port Application Settings
Setting Application LM Local Management Session
UPS APC Power Supply SNMP Proxy
3. Press ENTER to accept the application.
4. Use the arrow keys to highlight SAVE at the bottom of the screen, then
press the ENTER key.
5. When the message “SAVED OK” appears, the edits you made are
saved.
6E123-50 and 6E133-49 User’s Guide 5-53
Page 100
Chapter 5: Local Management
When the COM port is configured to perform the UPS
!
CAUTION
application, all future Local Management connections must be made by establishing a Telnet connection to the module. Ensure that the module has a valid IP address before saving changes to the COM port application. If the module does not have a valid IP address and the changes are saved, refer to
Appendix C for instructions on clearing NVRAM in order to
reestablish COM port communications.
5.15.13 Clearing NVRAM
Clearing NVRAM will result in the loss of all user-entered
!
CAUTION
Clearing NVRAM allows the user to clear all user-entered parameters, such as IP address and Community Names from NVRAM.
parameters. Do not proceed unless this procedure is completely understood.
Clear NVRAM as follows:
1. Use the arrow keys to highlight the Clear NVRAM field.
2. Use the SPACE bar to toggle the field to YES.
3. Use the arrow keys to highlight SAVE at the bottom of the screen.
4. Press ENTER. The warning shown in Figure 5-21 is displayed.
5-54 6E123-50 and 6E133-49 User’s Guide
Loading...