Page 1
REV032309
MANUAL MEAT
TENDERIZER/CUBER
INSTRUCTIONS
MODEL # 07-3101-A
ATTENTION
If any components of this unit are broken or
the unit does not operate properly, please
contact Cabela’s Customer Service.
Retail Store Purchases: 1-800-905-2731 (U.S. & Canada)
Catalog and Internet Purchases: 1-800-237-8888
All International: 1-308-234-5555
DO NOT RETURN THE UNIT TO THE STORE
WHERE IT WAS PURCHASED!
Page 2
-2-
MANUAL MEAT
TENDERIZER/CUBER
MODEL # 07-3101-A
COMPONENT LIST
Before beginning the assembly, check the package contents for all of the parts.
If you are missing any parts, or if any parts are damaged, contact
Cabela’s Customer Service- Retail Store Purchases 1-800-905-2731 (U.S. & Canada) /
Catalog & Internet Purchases: 1-800-237-8888 / All International: 1-308-234-5555
DIAGRAM NO. PART DESCRIPTION PART NO.
1 Lower Housing 07-3184-A
2 Top Housing 07-3181-A
3 Handle 07-3125-A
4 Stainless Steel Blade Rack Assembly 07-3103
5 Stainless Steel Left Comb 07-3119
6 Stainless Steel Right Comb 07-3118
7 Housing Thumbscrew (2) 07-3166
8 Handle Thumbscrew 07-3145
9 C-Clamp (2) 07-3105
10 Base 07-3111
11 Left Leg 07-3179-L-A
12 Right Leg 07-3179-R-A
13 Chute 07-3182-A
14 Nylon Bushing 07-3127
15 Stainless Steel Tongs 07-3151
16 Screw for Chute and Base (6) 07-3183
17 Screw for Legs (4) 07-3180
18 Allen Wrench for Chute & Base Screws 07-3178
19 Allen Wrench for Leg Screws 07-3185
20 Shaft Clip (2) 07-3165
DIRECTIONS FOR USE
Remove all bones or hard items in the meat before tenderizing or cubing. Damage
to the unit may occur if bones or hard objects are pushed through.
Do not cube or tenderize meat that is more than 1” (2.5 cm) thick. Thicker meat
may get lodged in Blades, which may cause damage to the product.
Insert the meat to be tenderized or cubed into the mouth of the Chute until the
meat comes in contact with the Blades. Turn the Handle in a clockwise motion.
This will pull the meat through the Blades. Insert only one piece of meat at a time to
prevent jamming.
If a piece of meat is too short to reach the Blades, use the provided Tongs to
guide the meat to the Blades.
CAUTION! DO NOT press or push the meat into the Chute with your fingers or
any other object. Doing so may cause personal injury and/or damage to the unit. DO
NOT push the Tongs or other utensils into the Blades.
It may be necessary to pass the meat through the Cuber/Tenderizer several
times to obtain the desired results. You may also pass the meat through at different
angles if a different result is desired.
Clean the unit before and after each use.
•
•
•
•
•
•
•
-7-
Page 3
-3--6-
1
2
3
4
5
6
7
8
9
10
12
11
13
17
16
15
18
19
14
16
20
17
DISASSEMBLY & CLEANING INSTRUCTIONS
1. Keep children at a safe distance from machine while cleaning.
2. Remove the Handle Thumbscrew from the Handle. Remove
Handle from the Blade Rack Shaft by unscrewing the Handle
Thumbscrew.
3. Remove the Combs from the Top Housing by lifting up on
Combs.
4. Remove the two Thumbscrews from the Top Housing.
5. Remove the Top Housing. WARNING! This will expose the Cutting Blades.
Take care when handling the Blade Assembly.
6. Using the provided Allen Wrench, remove the Chute from the Top Housing.
7. Carefully lift the Blade Rack Assembly from the Lower Housing.
8. Disassemble the Lower Housing from the Legs. Disassamble the Legs from
the Base.
8. Wash all parts thoroughly with warm, soapy water. Rinse with clear water. A
long bristle brush is recommended for cleaning the Blade Rack Assembly. Take
extra care when handling the Blade Racks.
9. Dry thoroughly before re-assembling.
NOTE: It is highly suggested to coat all metal parts with a food-grade silicone spray
(sold separately) to prevent corrosion.
Page 4
-4- -5-
WARNING!
SAVE THESE INSTRUCTIONS!
Refer t o them ofte n and use t hem to instr uct others.
GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS PRODUCT.
YOUR SAFETY IS MOST IMPORTANT! FAILURE TO
COMPLY WITH PROCEDURES AND SAFEGUARDS MAY
RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE.
REMEMBER: YOUR PERSONAL SAFETY IS YOUR
RESPONSIBILITY!
1. NEVER REACH INTO the Cuber/
Tenderizer. Doing so could cause serious
injury. ALWAYS USE THE PROVIDED
TONGS.
2. KEEP FINGERS CLEAR OF THE BLADES
AT ALL TIMES. Failure to do so may result in
personal injury. The Cutting Blades/Blade
Assembly is very sharp. It is recommended
to wear Kevlar, cut resistant gloves when
handling the Blades.
3. DO NOT press or push meat into the Chute
with your fingers or any other object. Doing
so may cause personal injury and/or damage
to the unit.
4. NEVER use fingers to scrape food away
from the Cuber/Tenderizer while the grinder
is in operation. SEVERE INJURY MAY
RESULT.
5. DO NOT push the Tongs or other utensils
into the Blades.
6. NEVER LEAVE THE Cuber/Tenderizer
UNATTENDED. Close supervision is
necessary when any appliance is used near
children. This appliance is NOT to be used by
children.
7. NEVER use any accessories or parts from
other manufacturers. Doing so will VOID YOUR
WARRANTY.
8. Thoroughly clean all parts that will come
into contact with food before using the
Tenderizer/Cuber. Wash all parts by hand
and dry thoroughly. WARNING! Protective/
cut-resistant Kevlar gloves are recommended
when handling the blade assembly.
9. DO NOT attempt to tenderize meat with
bones or other hard items. Damage to the
machine will occur.
10. TIE BACK loose hair and clothing, and roll
up long sleeves before operating the Cuber/
Tenderizer. REMOVE ties, rings, watches,
bracelets, or other jewelry before operating the
Cuber/Tenderizer.
11. DO NOT use the Cuber/Tenderizer while
under the influence of drugs, medications or
alcohol.
ASSEMBLY INSTRUCTIONS
1. Connect the Left and Right Legs to the
Base using the provided Allen Wrench and
Screws.
2. Using an Allen Wrench and Screws,
attach the Left and Right Legs to the Lower
Housing. Figure 1
3. Install the Chute to the Top Housing
using an Allen Wrench, Screws.
4. Insert the Blade Rack Assembly into
the Lower Housing, guiding the Drive
Shaft into the bearing journals. Make sure
the teeth of the Blade Racks are properly
meshed together.
5. Position the Top Housing onto the Lower
Housing and line up the screw holes.
6. Secure the Top Housing to the Lower
Housing using the Housing Thumbscrews.
DO NOT OVERTIGHTEN!
7. Insert the Left Comb and Right Comb
into the Top Housing. Figure 2
NOTE: The Left Comb is marked with an
“L” on the upper portion of the Comb. The
Top Housing is marked with an “L Comb”
and “R Comb” to aid in Comb installation.
8. Install Handle onto the Blade Rack Shaft.
Secure the Handle to Blade Rack Shaft with
the Handle Thumbscrew .
Figure 1
Legs
Lower
Housing
Base
Chute
Top
Housing
Blade Rack
Assembly
Blade Rack
Shaft
Figure 2
Comb
Loading...