Bushnell First Strike 730005, First Strike AR730005, First Strike AR730005C User Manual

Model # 730005 / AR730005 / AR730005C

Lit #: 98-2313/03-13

Reex Red Dot Sight

3

Congratulations on your purchase of the Bushnell
“First Strike” electronic reex sight. Featuring a 5
MOA red dot reticle with convenient self-regulating
brightness, and a fully waterproof and shockproof
design with integrated mount, this is a state-of-the­art scope designed for hunting, plinking and target
shooting with pistols, ries, shotguns and bows.

Engineered for greater speed and accuracy, this
sight allows you to focus on the target rather than
a reticle, thus increasing accuracy. The First Strike’s
electronic illuminated dot has been pre-focused so
the point of aim always appears against the target.
By comparison, standard rie or pistol scopes bring
the target into focus only on the internal reticle.

Its aiming system is engineered to be the brightest
of its kind. All in all, this sight is proof positive that
Bushnell is positioned squarely on the leading edge
of advanced technology.

The model# AR730005/AR730005C versions of the
First Strike sight include a tall riser block to position
the sight at an optimum height on AR-15 at tops or
tactical shotguns (see pg. 7).

4

A-Photocell
B-Integrated

Mount

C-Lg. Hex Bolt
D-Lens
E-Elevation Adj

Screw
F-Windage Adj
Screw

G-Sm. Hex Bolts
H-Protective

Cover
I-Alignment
Pins

A B C

D

Parts Guide

H

E

F

G

5

Included Accessories:

• CR 2032 3v Lithium Battery (J)

• Large Hex Wrench/Screwdriver (K)

• Small Hex Wrench (L)

• Protective Cover (previous page) (H)

J

I

L

Parts Guide

G

I

K

6

MOUNTING YOUR FIRST STRIKE REFLEX SIGHT

• Any Weaver or Picatinny style base is suitable for

mounting the First Strike (model# 730005). Make
sure the base you use is manufactured specically
for your pistol, rie or shotgun. Be sure the base is
properly installed and securely fastened according
to the manufacturer’s instructions for your safety.

• There is no set eye relief for this sight, therefore, you
should provide at least three inches of clearance
between the end of the sight and your eye when in
the shooting position.

• Loosen the hex bolt on the mount of the sight (C)

using the large hex wrench (K). Position the mount
on your base rail so that the crossbolt engages a slot.
Tighten the hex bolt.

MOUNTING THE FIRST STRIKE SIGHT WITH HI-RISE
BLOCK (AR models only)

The AR730005/AR730005C versions of the First Strike

Reex Sight are supplied with a “Hi-Rise” mounting

block that can be used to position the sight at the
correct height for optimum performance on an AR-15
style rie with a at top receiver.

In order to use the riser block, rst install the sight onto
the block by following the steps in the previous section
(“Mounting Your First Strike Reex Sight”). Once the sight

is installed on the Hi-Rise block, the entire assembly can

7

be mounted on the weapon by following these steps:

1. Loosen the mounting screw so that the clamp will

t over the tapered side of the rearm’s Picatinny
or Weaver rail.

2. Insure that the tapered clamp on the riser is

oriented with the chamfered (beveled) end of the
clamp at the top (Fig. 1).

3. Ensure that the riser’s cross screw with nut is

tightened to clamp it rmly to the weapon’s rail
(Fig. 2). Turn the large nut on the riser block ¼ to
½ turn with a coin, screwdriver or ½” wrench.

WARNING! Do not over tighten.

4. Complete zeroing according to the “Zeroing Your

First Strike” section that follows.

AR730005/AR730005C

Fig. 1

Fig. 2

8

ZEROING YOUR FIRST STRIKE REFLEX SIGHT

Note: the following should be done at an approved
range or other safe area. Eye and ear protection is
recommended.

The First Strike scope has an integrated photocell

(pg.

4, A),

which automatically activates the unit when the

protective lens cover

(H)

is removed, so there is no power

switch. When you are nished using the scope, simply

replace the cover to turn the power o again. Brightness
of the 5 moa red dot is also automatically regulated by
the photocell, based on the level of ambient light.

1. With the scope mounted and with the protective

lens cover

(H)

removed, rest the gun on a solid

support.

2. Start by sighting along the barrel and aim at a

target 25 to 50 yards away. View through your

electronic sight and gently rotate the windage (F)

Distance 1 Full Revolution of Adjustment Screw

25 yds 12.5 inches

50 yds 25 inches

100 yds 50 inches

Distance 1 Hash Mark of Adjustment Screw

25 yds 1.5 inches

50 yds 3 inches

100 yds 6 inches

Point of Impact Change Chart

9

and elevation adjustments (E), using the supplied
large hex wrench/screwdriver

(K)

, to align the red

dot with the target as seen along the barrel.

3. You should then re a test shot to determine the

point of impact of your weapon. If you are not
hitting your aiming point (the center of the target)
make an adjustment by turning the windage or
elevation screw(s) in the direction you want the
bullet to move. The chart on the next page will
aid you in determining the proper amount of
adjustment necessary depending upon the range
at which you are shooting.

REPLACING THE BATTERY

Y

our new Bushnell First Strike electronic sight is

powered by one 3V “coin-style” lithium battery, Type
2032 (J) (pre-installed). Should your reticle grow dim

or not light at all, you will need to replace the battery.
To install a new battery, use the provided small hex
wrench (L) to loosen the two bolts (G) on the top panel.
Remove the top section of the sight and insert the

battery “+” side up as shown in the Parts Guide. Align

and replace the top section and tighten the bolts (G).

Adjusting the Windage

(F)

10

LITHIUM BATTERY REFERENCE CHART

Duracell

Sunrise/

Radio

Shack

NEDA

Type

(size)

DL2032 CR2032 5004L

Other brands of batteries not listed in the chart are
available and suitable for use with your First Strike
sight. Refer to “coin cell” NEDA type when purchasing
batteries or consult with your dealer.

Reticle Type 5 moa red dot

Finish Matte black

Weight 2.1oz / 60g

(4.3oz/122g w/hi-rise block)

Length 52 mm

Mounting

Length

50 mm

Adjustment
Range

240 moa

TECHNICAL SPECIFICATIONS:

CAUTION: BE SURE GUN IS NOT

LOADED WHEN INSTALLING BATTERIES

ONE YEAR LIMITED WARRANTY

Your Bushnell® First Strike elecronic reex sight is warranted to be free
of defects in materials and workmanship for one year after the date
of purchase. In the event of a defect under this warranty, we will, at
our option, repair or replace the product, provided that you return the
product postage prepaid. This warranty does not cover damages caused
by misuse, improper handling, installation, or maintenance provided by
someone other than a Bushnell Authorized Service Department.

Any return made under this warranty must be accompanied by the items
listed below:

1) A check/money order in the amount of $10.00 to cover the cost of
postage and handling

2) Name and address for product return

3) An explanation of the defect

4) Proof of Date Purchased

5) Product should be well packed in a sturdy outside shipping carton,

to prevent damage in transit, with return postage prepaid to the
address listed below:

IN U.S.A. Send To: IN CANADA Send To:

Bushnell Outdoor Products Bushnell Outdoor Products

Attn.: Repairs Attn.: Repairs

9200 Cody 25A East Pearce Street, Unit 1
Overland Park, Kansas 66214 Richmond Hill, Ontario L4B 2M9

For products purchased outside the United States or Canada please

contact your local dealer for applicable warranty information. In Europe

you may also contact Bushnell at: Bushnell Germany GmbH

European Service Centre
Mathias-Brüggen-Str. 80

D-50827 Köln, GERMANY
Tel: [phone]
Fax: [phone]

This warranty gives you specic legal rights.

You may have other rights which vary from country to country.

©2013 Bushnell Outdoor Products

©2013 Bushnell Outdoor Products

For further questions or additional information

please contact:

Bushnell Outdoor Products

9200 Cody, Overland Park, Kansas 66214

[phone] • www.bushnell.com