Bushnell 98041, 98037 User Manual

SPRAY



s subject to change without notice.

SPRAY

EQUIPMENT

OPERATION MANUAL

Hysol 175-

P/N 98037

Hysol 175-

P/N 98041

-HT

Loctite America

1001 Trout Brook Crossing Rocky Hill, CT 06067-3910

Loctite Brazil

Av. Prof. Vernon Krieble, 91 06690-11-Itapevi São Paulo-Brazil

Loctite Canada Inc.

2225 Meadowpine Boulevard Mississauga, Ontario L5N 7P2

Loctite Company de México, S.A.d e C.V.

Calzada de la Viga s/n, Fracc. Los Laureles Loc. Tulpetlac, C.P. 55090 Ecatepac de Morelos, Edo. de México, México

www.loctite.com

A Company

Contents

1. Please Observe the Following................................................................................... 2

1.1. Safety .......................................................................................................................... 2

1.2. Items supplied.............................................................................................................. 2

2. Description................................................................................................................. 2

3. Technical Data............................................................................................................ 3

4. Installation.................................................................................................................. 3

5. Operation.................................................................................................................... 4

5.1. Applying Adhesive - Spray Adjustment ......................................................................... 4

5.2. Adhesive Flow Rate Adjustment ................................................................................... 4

6. Application Hints........................................................................................................ 5

7. Troubleshooting......................................................................................................... 5

8. Care and Maintenance ............................................................................................... 6

9. Accessories and Spare Parts .................................................................................... 6

10. Warranty.....................................................................................................................8

11. Appendix. ................................................................................................................... 9

12. Exploded Diagram.................................................................................................... 10

13. Parts List. ................................................................................................................. 11

Page 1

1. Please Observe the Following

1.1.Safety

Do not touch the nozzle or molten adhesive with bare skin as they are hot - the operating temperature of the Loctite

Hysol® 175-SPRAY and 175-SPRAY-HT

applicators is approximately 400ºF (200ºC). Protective gloves should always be worn. Careless handling can cause skin burns. If molten adhesive comes into

contact with the skin immerse the affected area immediately in plenty of cold water. Seek medical advice if necessary. In addition to the safety instructions herein, any statutory regulations, local fire insurance regulations, or other generally valid “regulations for accident prevention” must be complied with when using this tool.

• Never use the tool if it is damaged in any way.

• Do not use this tool in damp rooms, outdoors while it is raining, or where there is

high humidity.

• Do not use this tool in the vicinity of any heat-sensitive materials, or any flammable materials, liquids, or gases.

• Only use extension cables that meet the specification shown in “Technical data”.

• Never pull on the tool’s connecting cable.

1.2. Items supplied

Loctite

Hysol® 175-SPRAY

Pneumatically-driven Hot Melt Cartridge Spray Dispenser, fitted with 356°F (180°C)

thermostat (suitable for standard spray hotmelt adhesives) Valve body airline adaptor Plastic Stand Manual

Loctite

Pneumatically-driven Hot Melt Cartridge Spray Dispenser, fitted with 383°F (195°C)

Valve body airline adaptor Plastic Stand Manual

2. Description

The Loctite held industrial spray hotmelt applicators available. With its two powerful 250W stainless steel cartridge heaters, they are capable of dispensing up to 9 lbs. of molten hotmelt per hour, yet only take 10 minutes to warm up from cold.

Supported by a range of spray adhesive formulations, the Loctite and 175-SPRAY-HT are suitable for most applications - they can even be used with heat sensitive substrates such as expanded polystyrene and other plastic foams. Also, the Loctite non-toxic, so there are none of the environmental problems often associated with other spray adhesive applicators.

Designed to comply with world wide safety standards, the Loctite and 175-SPRAY-HT also feature a totally enclosed heater housing, and are fitted with thermal fuse protection.

Hysol® 175-SPRAY-HT

thermostat (suitable for polyamide spray hotmelt adhesives)

Hysol® 175-SPRAY and 175-SPRAY-HT are the highest output, hand-

Hysol® 175-SPRAY

Hysol® 175-SPRAY and 175-SPRAY-HT system are solvent-free and

Hysol® 175-SPRAY

Page 2

3. Technical Data

Dimensions (L x H x W): approx. 11 13/16” x 9 15/32” x 2 17/32”

Total weight: approx. 3 lbs. (1.4 Kg) Connection cable with mains plug: 10 ft (3 m) long Operating voltage: 110-120 VAC 50/60Hz Power consumption 500W Heating up time: 10 minutes Operating temperature: 175-SPRAY approx. 356°F (180°C)

Diameter of adhesive inlet: 1 11/16” (43 mm) Extension cable: max. 65ft (20 m) long Wire cross section: at least 16 a.w.g. (1.5 mm Air Supply / Pneumatic Minimum - 45 p.s.i. (3 bar)

Approximate Spray Pattern Minimum Maximum Ultra Wide Spray Pattern / 985216 1 ½” [38mm] 6” [150mm] Wide Spray Nozzle Assembly / 985122 1 ¼” [32mm] 5” [127mm] Narrow Spray Pattern Assembly / 985211 ½” [13mm] 1 ¼”[32mm]

4. Installation

Before using the tool for the first time check it carefully for signs of external damage. If any transit damage is found DO NOT USE THE TOOL - return it to your supplier immediately.

(Approx. 300 x 240 x 65 mm)

175-SPRAY-HT approx. 383°F (195°C)

)

Maximum - 100 p.s.i. (7 bar)

Steps 1 – 5 should be followed before connection to the mains supply:

1. Insert the applicator stand into the grooves at the base of the handle. Stand

applicator on a flat surface.

2. Connect the air supply hose to a clean, dry and regulated air supply using the

Quick-Disconnect fitting provided (use of a filter/regulator is recommended)

3. Pull piston back fully and rotate upwards.

4. Load two adhesive cartridges into the barrel of the tool and push fully forward.

5. Rotate the piston down and slide forward fully until it contacts the rear of the

adhesive cartridge - it should engage about 5/16" (6-8mm) into the applicator

barrel.

USERS AIR SUPPLY

6. Connect tool to mains supply.

7. Red ‘Power On’ indicator light illuminates.

Page 3

+ 8 hidden pages