Bushnell 118213 User Manual

Model#: 118213 LIT. #: 98-0795/07-06

1.3 Megapixel

118213 QVC Imageview-1LIM.indd 1 8/17/06 10:19:03 PM

118213 QVC Imageview-1LIM.indd 2 8/17/06 10:19:03 PM

Congratulations on your purchase of the Bushnell ImageView® binocular! The

Bushnell ImageView binocular takes the technology of digital photography

and combines it with a high-quality compact binocular. This allows you

to observe sporting events, wildlife, scenic vistas or anything you would

normally use a binocular for, and then save the image in a built-in attached

digital camera. You can then download these images to your computer and e-

mail them to your friends and family, print off the picture using the included

software or save them in a photo album for future use. Before using the

product, please read the instructions contained in this manual and take time

to familiarize yourself with the different parts and features of the product.

118213 QVC Imageview-1LIM.indd 3 8/17/06 10:19:03 PM

CAMERA OPERATION INSTRUCTIONS

BUTTON DESCRIPTIONS

The MODE button has three functions:

1. Power on: Press and hold the button until the camera turns on. When the camera is connected to a PC via the USB cable provided, the camera will power on automatically.

2. Power off: While the camera is on, press and hold the button until the camera turns off. If the camera has not been used or if a button has not been pressed for over 2 minutes, the camera will automatically power off to save battery life. If the camera is connected via USB, it will not power off except when the PC power is off.

3. Mode change: press the button rapidly to change modes.

B. The SNAP button has two functions:

1. Take a picture: press this button to take a picture when the camera is on. (But not in the PC mode or mode change.)

2. Select: in “Mode Change” press this button to confirm the function.

Mode Snap

118213 QVC Imageview-1LIM.indd 4 8/17/06 10:19:03 PM

LCD DISPLAY

1. High Resolution Mode = 1280x1024 Pixels

2. Low Resolution Mode = 640x480 Pixels

3. Select the timer to take a delayed picture. This gives you approximately a 10-second delay.

This mode allows you to take short movie clips, saved as “.avi” files.

5. Select different resolution mode.

6. Deletes all the pictures in the memory.

7. Deletes the last picture taken.

8. SD mark appears when an SD card is inserted.

9. USB mark appears when USB cord is connected between the camera and the PC.

10. Battery mark keeps track of the battery life left.

11. a. Picture Number — This area will show the number of pictures in the memory.

b. SET — select HQ (high quality)/LQ (low quality) mode, STO (Mass Storage)/ PCC (PC

Cam) mode, 50Hz/60Hz frequency

c. FUL — When the memory is full , the display will show “FUL”.

OPERATION GUIDE

1. The camera is powered by two AAA alkaline (included), lithium or NiMh batteries .

2. Insert the batteries into the battery compartment. Insert an SD card ("upside down" with metal

contacts facing up) in the slot if greater storage is desired . You may use SD cards up to 512 MB.

3. Press and hold the MODE button until the camera turns on.

Press SNAP to take a picture, or press the MODE button quickly to change mode settings as described above. The camera is set at infinity and will not be focused on an object closer than approx. 49 feet.

118213 QVC Imageview-1LIM.indd 5 8/17/06 10:19:04 PM

5. The mode setting operation is a cycle loop, so press the MODE button to switch to another mode. The loop order of the different modes is shown here:

6. To change settings, toggle through the different modes by pressing the MODE button. When a mode is selected, the indicator symbol on the LCD will appear. You can then select that mode by pressing the SNAP button.

7. When in “Normal” mode, press SNAP to take a picture.

Press SNAP->

8. Pressing the MODE button will cause the camera to enter “Mode Change”.

9. To select “Self-Timer” mode, press MODE and the self timer mark appears. Press SNAP and the capture will be done after 10 seconds. The camera exits self timer mode automatically after the capture is done and the self timer mark disappears on the LCD at the same time.

Press MODE-> press SNAP to capture.

118213 QVC Imageview-1LIM.indd 6 8/17/06 10:19:04 PM

+ 12 hidden pages