Bush Hog 300 User Manual

Page 1

300 Series

This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ,

UNDERSTAND, and FOLLOW the Safety

and Operation Instructions contained in this manual before operating the equipment. C01-

Cover

REAR MOUNTED BLADE

Published 09/10 Part No. 00786978C

OPERATOR’S MANUAL

BUSH HOG®

2501 Griffin Ave. Selma, AL 36703 334-874-2700 www.bushhog.com

$0.00

Page 2

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU ST AR T! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!

WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration

Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain.

Page 3

SAFETY SECTION ..............................................................................................................1-1

Safety Messages ................................................................................................................................................ 1-2

Decal Location....................................................................................................................................................1-9

Decal Description..............................................................................................................................................1-11

Federal Laws and Regulations ......................................................................................................................... 1-15

INTRODUCTION SECTION .................................................................................................2-1

ASSEMBLY SECTION ........................................................................................................ 3-1

Assembly of Moldboard to Mainframe ................................................................................................................3-2

Gauge Wheel (Extra Equipment)........................................................................................................................ 3-4

Skid Shoes & Quick Tack End Plates (Extra Equipment)...................................................................................3-4

Hydraulic System................................................................................................................................................ 3-5

Hydraulic Control Valve (Accessory Equipment) ................................................................................................3-5

Selector Valve (Accessory Equipment)............................................................................................................... 3-6

OPERATION SECTION .......................................................................................................4-1

Standard Equipment and Specifications.............................................................................................................4-3

OPERATOR REQUIREMENTS.......................................................................................................................... 4-4

TRACTOR REQUIREMENTS.............................................................................................................................4-5

ROPS and Seat Belt ........................................................................................................................................... 4-5

Tractor Horsepower......................... ... ....................................... ....................................... .................................. 4-5

Tractor 3-Point Hitch........................................................ .... ... ....................................... ... .................................. 4-6

Front End Weight................................................................................................................................................4-6

GETTING ON AND OFF THE TRACTOR .......................................................................................................... 4-6

Boarding the Tractor........................................................................................................................................... 4-7

Dismounting the Tractor...................................................................................................................................... 4-7

STARTING THE TRACTOR ............................................................................................................................... 4-8

CONNECTING THE REAR BLADE TO THE TRACTOR ...................................................................................4-9

Connecting the Rear Blade.............................. ................................................................................................... 4-9

PRE-OPERATION INSPECTION AND SERVICE............................................................................................4-10

Tractor Pre-Operation Inspection/Service.. ... ... .... ... ... ... ....................................... ............................................. 4-10

Blade Pre-Operation Inspection/Service...........................................................................................................4-11

DRIVING THE TRACTOR AND IMPLEMENT..................................................................................................4-14

Starting the Tractor ........................................................................................................................................... 4-15

Brake and Differential Lock Setting...................................................................................................................4-15

Driving the Tractor and Blade...........................................................................................................................4-16

OPERATING THE TRACTOR AND IMPLEMENT............................................................................................ 4-16

Operating the Blade............................................................. ... ... ....................................... ................................ 4-17

Shutting Down the Implement........................................................................................................................... 4-18

DISCONNECTING THE BLADE FROM THE TRACTOR................................................................................. 4-18

BLADE STORAGE............................................................................................................................................4-19

TRANSPORTING THE TRACTOR AND IMPLEMENT ....... ... ... ... .... ... ... ... .... ... ... ... ... .... ... ...... .... ... ... ... ... .... ... ... 4-19

Transporting on Public Roadways....................................................................................................................4-20

Hauling the Tractor and Implement...................................................................................................................4-22

TROUBLESHOOTING GUIDE ..................... ... ....................................... ... ....................................... ................4-24

MAINTENANCE SECTION ..................................................................................................5-1

Lubrication ..........................................................................................................................................................5-2

Proper Torque For Fasteners .............................................................................................................................5-3

Page 4

Page 5

SAFETY SECTION

Safety Section 1-1

Page 6

Safety Messages

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator . Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety Messages before assembling, operating or servicing this Implement. This equipment should only be operated by those persons who have read the manual, who are responsible and trained, and who know how to do so responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this manual and on decals which are attached to the equipment. The Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word are intended to warn the owner/operator of impending hazards and the degree of possible injury faced when operating this equipment.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.

(SG-1)

Practice all usual and customary safe working precautions and above all---remember safety is up to YOU

. Only YOU can prevent serious injury or death from unsafe practices.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad.

(SG-3)

SAFETY

300 Series 09/10 Safety Section 1-2

Page 7

SAFETY

Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency. Never allow inexperienced or untrained personnel to operate the Tractor or Implement without supervision. Make sure the operator has fully read and understood the manuals prior to operation.

(SG-4)

Always maintain the safety signs in good readable condition. If th e safety signs are missing, damaged, or unreadable, obtain and install replacement safety signs immediately.

(SG-5)

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be cl early visible and legible. When transport ing the Equipment use the Tractor flashing warning lights and follow all local traffic regulations.

(SG-6)

Operate this Equipment only with a Tractor equipped with an approved rollover-protective system (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS.

(SG-7)

Do not modify or alter this Implement. Do not permit anyone to modify or alter this Implement, any of its components or any Implement function.

(SG-8)

BEFORE leaving the tractor seat, always set the parking brake and/or set the tractor transmission in parking gear, disengage the PTO, stop the engine, remove the key, and wait for all moving parts to stop. Place the tractor shift lever into a low range or parking gear to prevent the tractor from rolling. Never dismount a Tractor that is moving or while the engine is running. Operate the Tractor controls from the tractor seat only.

(SG-9)

Never allow children or other persons to ride on the Tracto r or Implement. Falling off can result in serious injury or death.

(SG-10)

SAFETY

300 Series 09/10 Safety Section 1-3

Page 8

SAFETY

Never allow children to operate, ride on, or come close to the Tractor or Implement. Usually, 16-17 year-old children who are mature and responsible can operate the implement with adult supervision, if they have read and understand the Operator’s Manuals, been trained in proper operation of the tractor and Implement, and are physically large enough to reach and operate the controls easily.

(SG-11)

Do not mount or dismount the Tractor while the tractor is moving. Mount the Tractor only when the Tractor and all moving parts are completely stopped.

(SG-12)

Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operators manual for proper starting instructions.

(SG-13)

Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death.

(SG-14)

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil and fuel are explosive and their presence could present a hazard. Do not check for leaks with your hand! High-pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene. To check for a hose leak, SHUT the unit ENGINE OFF and remove all hydraulic pressure. Wear oil imp ene trab le glo ves , safety glasses and use Cardboard to check for evidence of oil leaks. If you suspect a leak, REMOVE the HOSE and have it tested at a Dealer. If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure.

(SG-15)

The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items that may be thrown by the equipment.

(SG-16)

SAFETY

300 Series 09/10 Safety Section 1-4

Page 9

SAFETY

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS! Tractors with or without an Implement attached can often be noisy enough to cause permanent hearing loss. We recommend that you always wear hearing protection if the noise in the Operator’s position exceeds 80db. Noise over 85db over an extended period of time will cause severe hearing loss. Noise over 90db adjacent to the Operator over an extended period of time will cause permanent or total hearing loss. NOTE: Hearing loss from loud noise

[from tractors, chain saws, radios, and other such sources close to the ear] is cumulative over a lifetime without hope of natural recovery.

(SG-I7)

Transport only at speeds where you can maintain control of the

equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement. As you increase the speed of the Tractor the stopping distance increases. Determine the maximum transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that the equipment can be operated at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum turning speed for you and this equipment before operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and red uce your speed. Be a ware of traf fic around yo u and watch out for the other guy.

(SG-19)

Never attempt to lubricate, adjust, or remove material from the Implement while it is in

motion or while tractor engine is running.

(SG-20)

SAFETY

300 Series 09/10 Safety Section 1-5

Page 10

SAFETY

Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order.

(SG-21)

Always read carefully and comply fully with the manufacturer’s instructions when handling oil, solvents, cleansers, and any other chemical agent.

(SG-22)

Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health.

(SG-23)

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement and possible serious injury or death.

(SG-24)

Never allow children to play on or around Tractor or Implement. Children can slip or fall off the Equipment and be injured or killed. Children can cause the Implement to shift or fall crushing themselves or others.

(SG-25)

NEVER use drugs or alcohol immediately before or while operating the

Tractor and Implement. Drugs and alcohol will affect an operator’s

alertness and coordination and therefore affect the operator’s ability to

operate the equipment safely. Before operating the Tractor or Implement,

an operator on prescription or over-the-counter medication must consult

a medical professional regard ing any side effects of the medication that

would hinder their ability to operate the Equipment safely. NEVER

knowingly allow anyone to operate this equipment when their alertne ss or

coordination is impaired. Serious injury or death to the operator or others

could result if the operator is under the influen ce of drugs or a lcohol.

(SG-27)

SAFETY

300 Series 09/10 Safety Section 1-6

Page 11

SAFETY

Operate the Tractor and/or Implement control s only while properly seated in the Tractor seat with the seat belt securely fastened around you. Inadvertent movement of the Tractor or Implement may cause serious injury or death.

(SG-29)

Be particularly careful when transporting the Implement with the Tractor. Turn curves or go up hills only at a low speed and using a gradual steering angle. Rear mounted implements move the center of gravity to the rear and remove weight from the front wheels. Make certain, by adding front ballast, that at least 20 % of the tractor’s weight is on the front wheels to prevent rearing up, loss of steering control or Tractor tip-over. Slow down on rough or uneven surfaces to prevent loss o f steering control which could result in property damage or possible injury. Do not transport unless 3-Point lift lever is fully raised and in the latched transport position. Dropping implement in transport can cause serious damage to the tractor and/or Implement and possibly cause the operator or others to be injured or killed.

(S3PT-02)

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Implement on the ground or securely blocked up, disengage the PTO, and turn off the tractor engine. Push and pull the Remote Cylinder lever in and out several times prior to starting any maintenance or repair work.

(S3PT-09)

This Implement may be wider than the Tractor. Be careful when operating or transporting this equipment to prevent the Implement from running into or striking sign posts, guard rails, concrete abutments or other solid objects. Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control, serious injury, or even death. Never allow the Implement to contact obstacles.

(S3PT-12)

There are obvious and hidden potential hazards in o peratin g Rea r Blades an d Bo x Scra pers as in all power-driven equipment. REMEMBER! This machine is often operated in rough terrain conditions that include gullies, holes, slopes, hidden obstructions and the like. Serious injury or even death may occur unless care is taken to assure the personal sa fe ty of the operator and bystanders in the area.

(SBL-1)

NEVER PARK BLADE ON THE BACK OF THE MOLDBOARD. Inadvertent falling could cause serious injury or even death. ALWAYS LOWER HITCH onto stand or onto secure blocks.

(SBL-2)

Never leave blade unattended in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with subsequent injury or death by crushing. Lower Stand and pin in place, or put a secure support under the A-Frame. Lower Blade carefully to the ground. Do not put hands or feet under lifted components.

(SBL-4)

SAFETY

300 Series 09/10 Safety Section 1-7

Page 12

SAFETY

Rear Blades can fall down if not properly supported. Always use the stand on the front hitch or block up securely to prevent falling and possible crushing injury and/or back injury from lifting heavy components.

(SBL-5)

PARTS INFORMATION

Bush Hog products are designed utilizing specifically matched system components to ensure optimum equipment performance. These parts are made and tested to Bush Hog specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment performance, void warranties, and present a safety hazard. Use genuine Bush Hog parts for economy and safety.

(SPBH-2)

SEE YOUR BUSH HOG DEALER

In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

(SG-18)

SAFETY

300 Series 09/10 Safety Section 1-8

Page 13

SAFETY

Decal Location

NOTE: Bush Hog supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in shipping, use, or recondition ing. Bush Hog cares about the safety of its customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of charge (Some shipping and handling charges may apply). Contact your Bush Hog dealer to order replacement decals.

SAFETY

300 Series 09/10 Safety Section 1-9

Page 14

SAFETY

ITEM PART NO. QTY LEVEL DESCRIPTION

1. 00725746 1 PELIGRO Translate Safety Material

2. 02965262 1 WARNING Oil Penetration

3. 00786980 1 IMPORTANT Genuine Bush Hog Parts

4. 999000 1 WARNING Multi-Hazard for Blades

5. 999200 1 WARNING Multi-Hazard General

6. 03200347 * REFLECT SMV Emblem

7. 000678 2 INSTRUCT Grease Fitting Inside

8. 00763977 1 INSTRUCT Notice to Owner

9. 00786979 3 LOGO Bush Hog

10. 00786984 1 NAME 300-12

SAFETY

00786992 1 NAME 300-14

11. nfs 1 SER PLT Serial Plate

12. 1458393 2 REFLECT Amber Reflectors

13. 1458392 4 REFLECT Red Reflectors

14. 1458398 4 REFLECT Fluorescent

15. 49722 1 _________ Canister, Operator’s Manual

16. 00786978C 1 MANUAL Operator’s Manual

*Furnished by Tractor Manufacturer

300 Series 09/10 Safety Section 1-10

Page 15

Decal Description

Peligro Translation, If you do not know how to read English, please find someone who knows how to read English.

P/N 00725746

WARNING! Failure to INSPECT and REPAIR or REPLACE Hoses may allow worn Hoses to rupture SUDDENLY and VIOLENTLY with resulting serious BODILY INJURY from SCALDING or FIRE with resulting BURN INJURY or DEATH.

P/N 02965262

For safety and to guarantee optimum product reliability always use genuine Bush Hog replacement parts.

P/N 00786980

WARNING!-Multi-Hazard for blades

P/N 999000

SAFETY

300 Series 09/10 Safety Section 1-11

Page 16

SAFETY

WARNING!- Multiple Hazard and General Safety

P/N 999200

Slow Moving Vehicle Decal. Keep SMV reflector clean and visible. DO NOT transport or operate without the SMV.

P/N 03200347

Information that Grease Fitting is present and must apply grease

P/N 000678

Operator's Manual (with repair parts) and warranty was attached to this implement during final inspection.

P/N 00763977

SAFETY

300 Series 09/10 Safety Section 1-12

Page 17

SAFETY

P/N 00786979

Logo Product Name: Bush Hog

P/N 00786984

LOGO PRODUCT NAME: 300-12

P/N 00786992

LOGO PRODUCT NAME: 300-14

Red Reflector. Keep reflectors clean and visible.

P/N 1458392

SAFETY

300 Series 09/10 Safety Section 1-13

Page 18

SAFETY

Amber Reflector. Keep reflectors clean and visible.

P/N 1458393

Orange Reflector. Keep reflectors clean and visible.

P/N 1458398

Read Operator’s Manual! The operator’s manual is located inside this canister. If the manual is missing order one from your dealer.

P/N 00776031

SAFETY

300 Series 09/10 Safety Section 1-14

Page 19

SAFETY

Federal Laws and Regulations

This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such.

Employer-Employee Operator Regulations

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as possible every working man and woman in the nation safe and healthful working conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer(1) shall furnish to each of his employees employment and a place of employment which are free from

recognized hazards that are causing or are likely to cause death or serious physical harm to his employees; (2) shall comply with occupational safety and health standards promulgated under this Act. (b) Each employee shall comply with occupational safety and health standards and all rules, regulations and

orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Training Requirements

Title 29, Code of Federal Regulations Part 1928.57(a)(6). www.osha.gov Operator instructions. At the time of initial assignment and at least annually thereafter, the employer shall

instruct every employee who operates an agricultural tractor and implements in the safe operating practices and servicing of equipment with which they are or will be involved, and of any othe r practices dictated by the work environment.

Keep all guards in place when the machine is in operation; Permit no riders on equipment Stop engine, disconnect the power source, and wait for all machine movement to stop before servicing,

adjusting, cleaning or unclogging the equip ment, except where the machine must be running to be properly serviced or maintained, in which case the employer shall instruct employees as to all steps and procedures which are necessary to safely service or maintain the equipment.

Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the machine.

Employer Responsibilities:

To ensure employee safety during Tractor and Implement operation, it is the employer’s responsibility to:

1. Train the employee in the proper and safe operation of the Tractor and Implement.

2. Require that the employee read and fully understand the Tractor and Implement Operator’s manual.

3. Permit only qualified and properly trained employees to operate the Tractor and Implement.

4. Maintain the Tractor and Implement in a safe operational condition and maintain all shields and guards on the equipment.

5. Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee ope rator securely fasten the safety belt and operate with the ROPS in the raised position at all times.

6. Forbid the employee operator to carry additional riders on the Tractor or Implement.

7. Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the necessary support devices to secure the equipment safely while performing repairs and service.

8. Require that the employee operator stop operation if bystanders or passersby come within 25 feet.

Child Labor Under 16 Y ear s of Age

Some regulations specify that no one under the age of 16 may ope rate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.)

300 Series 09/10 Safety Section 1-15

SAFETY

Page 20

Page 21

INTRODUCTION SECTION

Introduction Section 2-1

Page 22

INTRODUCTION

This 300 Series is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine.

The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in the correct assembly of the Blade using standard and optional equipment.

Careful use and timely service saves extensive repairs and costly downtime losses. The Operation and Maintenance Sections of the manual train the owner/operator how to work the Blade correctly and attend to appropriate maintenance. The Trouble Shooting Guide helps diagnose difficulties and offers solution to the problems.

Safety is of primary importance to the owner/ope ra tor and to the manufacturer. The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death. Many of the Safety Messages will be repeated throughout the manual. The owner/operator/dealer should know these Safety Messages before assembly and be aware of the hazards of operating this blade during assembly, use, and maintenance. The Safety Alert Symbol combined with a Signal Word, as seen below, is intended to warn the owner/operator of impe nding hazards and the deg ree of possible injury faced when operating this machine.

INTRODUCTION

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in damage to, or destruction of the machine, atta ch me nts or the en vir on m en t.

300 Series 09/10 Introduction Section 2-2

Page 23

INTRODUCTION

The 300 Series Blade is available in widths of 12' and 14' and features a massive CAT III-IV three-point hitch and quick-hitch. The 14' model is rated for up to 250 draw bar horsepower wheel-type tractors. Hydraulic adjustment of the mainframe swing, moldboard angle, and moldboard tilt is standard for easy and fast adjustments. The 300 Series features a maximum of 50" of offset to easily reach outside the dual wheels of large tractors. The 5" diameter solid steel kingpin, boxed-section, reinforced 1/2” x 20" moldboard, and heavyduty hitch and mainframe provide the dependability Bush Hog blades are known for. Skid shoes, quick-tach end plates, and dual gauge wheels are optional equipment adding to the versatility of the 300 Series blade.

At least 20% or the tractor’s weight must be on the front tires with the implement lifted to provide adequate traction for safe steering under good conditions. Slow down on hills, rough terrain, and curves.

Front and rear, and left and right are determined by the normal direction of travel (the same as on your automobile).

300 Series 09/10 Introduction Section 2-3

Page 24

INTRODUCTION

Attention Owner/Operator

BEFORE OPERATING THIS MACHINE:

1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and know how to operate correctly both the tractor and implement.

2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the implement. Mail within 30 days of delivery date of this implement.

NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by Alamo Group within thirty days of delivery of the implement.

3. Record the Blade Model and Serial Numbers on the Warranty page at the front of the Operator’s Manual. Keep this as part of the permanent maintenance file for the implement.

INTRODUCTION

300 Series 09/10 Introduction Section 2-4

Page 25

ASSEMBLY SECTION

Assembly Section 3-1

Page 26

ASSEMBLY

Assembly of Moldboard to Mainframe

The Bush Hog 300 Series Blade is shipped in two bundles. The Mainframe, A-Frame and Moldboard Carrier are in one bundle; the Moldboard is in the second bundle. The assembly of the Moldboard to the Moldboard Carrier is made by inserting the Moldboard Pivot Pin and securing with Bolts.

ASSEMBLY

Until Hydraulic Cylinders are connected and under pressure, block Moldboard to Moldboard Carrier to prevent possible tilting and falling from stand.

300 Series 09/10 Assembly Section 3-2

Page 27

ASSEMBLY

1. Attach Moldboard T ilt Cylinder with the Rod End attached to the Moldboard.

2. Attach the Moldboard Pivot Cylinder.

ASSEMBLY

3. Attach the Mainframe Swing Cylinder.

300 Series 09/10 Assembly Section 3-3

Page 28

ASSEMBLY

Gauge Wheel (Extra Equipment)

Mounting Holes have been provided for mounting the Gauge Wheel to the Mainframe. Dual Wheels with laminated puncture proof tires are optional. Assembly of the Hydraulic Cylinder to the Gauge Wheel Beam must be in the direction as shown in Figure Asm-0005. It is also important to route the hydraulic Hose through the Hose Retainers designed for this equipment.

ASSEMBLY

Skid Shoes & Quick Tack End Plates (Extra Equipment)

Skid Shoes prevent gouging and scalping and increase Blade life. End Plates help move larger quantities of bulk material. Install as shown in Figure Asm-0006. Neither can be used while ditching.

300 Series 09/10 Assembly Section 3-4

Page 29

ASSEMBLY

Hydraulic System

The Hydraulic Cylinders are designed to be used in conjunction with your tractor's Hydraulic System. The Cylinders and Hose are designed for maximum system pressure of 2500 PSI.

Keep Cylinders and Hoses free from internal contamination. Never leave a disconnected Hose end open. Use a Sealant when attaching Hydraulic Hose to Cylinder. Do not over tighten fittings as this will break out the Cylinder Port Housings. Do not operate with hydraulic oil leaking. Oil is expensive and its presence could cause slips and falls and other hazards. DO NOT CHECK FOR LEAKS WITH YOUR HAND. USE CARDBOARD INSTEAD. High-pressure oil can penetrate the skin and cause tissue damage or even GANGRENE. If oil does penetrate the skin, have it REMOVED IMMEDIATELY by a surgeon skilled in this procedure.

Hydraulic Control Valve (Accessory Equipment)

A three-spool, four way Hydraulic Control Valve, Open Center or Closed Center, is available as Accessory Equipment. This allows you to operate four Hydraulic Cylinders from two remote outlets. Connect the threespool Valve to one outlet to operate three Cylinders. Use the other remote outlet to op era t e the four th Cylin de r.

ASSEMBLY

If Closed Center Valve is used, Do Not Use the Adjustable Relief Assembly. Use the NoRelief Assembly.

300 Series 09/10 Assembly Section 3-5

Page 30

ASSEMBLY

Selector Valve (Accessory Equipment)

The Mainframe Swing, Moldboard Pivot and Tilt are fully hydraulic. All three Cylinders can be operated from two remote outlets. Below is a schematic diagram showing proper routing of two Cylinders through the Selector Valve. When installing this Valve, observe all safety precautions as Hydraulic Lines are under high pressure (2500 PSI). If additional information is required concerning your Hydraulic System, contact your Bush Hog Dealer.

ASSEMBLY

300 Series 09/10 Assembly Section 3-6

Page 31

OPERATION SECTION

Operation Section 4-1

Page 32

OPERATION

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND IMPLEMENT. If you do not understand any of the instructions, contact your nearest authorized dealer for a

full explanation. Pay close attention to all safety signs and safety messages contained in this manual and those affixed to the implement and tractor. OPS-U- 0001

(SG-2)

BUSH HOG 300 SERIES REAR MOUNTED BLADE

OPERATION INSTRUCTIONS

Your Bush Hog 300 Series should now be assembled and inspected for any evidence of defective or damaged parts before use. Any evidence of damage should be reported to your dealer immediately. After Hydraulic Lines have been attached to tractor and Three-Point Hitch attached, carefully remove safety blocks from Moldboard pivot Point.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper blade use to the operator. Pictures contained in this section are intended to be used as a visual aid to assist in explaining the operation of a rear blade and are not necessarily of a 300 Series blade. Some pictures may show shields removed for purposes of clarity. NEVER OPERATE this implement without all shields in place and in good operational condition. The operator must be familiar with the blade and tractor operation and all associated safety practices before operating the blade and tractor. Proper operation of the blade, as det ailed in this manual, will help ensure years of safe and satisfactory use of the rear blade.

OPERATION

300 Series 09/10 Operation Section 4-2

Page 33

OPERATION

1. Standard Equipment and Specifications

Max. Front Wheel Assist Tractor HP (Drawbar HP):

12’ 300 HP

14’ 250 HP Moldboard Width 12’ or 14’ Moldboard Dimension 1/2” x 20” Cutting Edge 1/2” x 6” Support Stand Std. Hitch CAT III-IV and QH King Pin Diameter 5” Steel Bar Adjustment Types Hydraulic Offset (Maximum Left or Right) 50” Pivot:

Forward Angle Up to 45°

Reverse Angle Up to 45° Tilt (Up and Down) Up to 15° No. of No-Wrench Adjustments N/A Weight (Approx.):

12’ 3463 lbs.

OPERATION

14’ 3603 lbs.

300 Series 09/10 Operation Section 4-3

Page 34

OPERATION

2. OPERATOR REQUIREMENTS

Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor operation and all associated safety practices. In addition to the safety messages contained in this manual, safety signs are affixed to the implement and tractor. If any part of the operation and safe use of this equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely und erst and the opera tion of the equipment, it is the responsibility of the supervisor to read and explain the manuals, safety practices, and operating instructions to the operator.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment (PPE) for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is designed to provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

• Always Wear Safety Glasses

•Hard Hat

• Steel Toe Safety Footwear

• Gloves

• Hearing Protection

• Close Fitting Clothing

• Respirator or Filter Mask (depends on operating conditions) OPS-U- 0002

NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability to operate the equipment safely. Before operating the Tractor or Implement, an operator on prescription or over-the-counter medication must consult a medical professional regard ing any side effects of the medication that would hinder their ability to operate the Equipment safely. NEVER knowingly allow anyone to operate this equipment when their alertne ss or coordination is impaired. Serious injury or death to the operator or others could result if the operator is under the influen ce of drugs or a lcohol.

(SG-27)

OPERATION

300 Series 09/10 Operation Section 4-4

Page 35

OPERATION

3.1 ROPS and Seat Belt

The tractor must be equipped with a Roll-Over-Protective-Structure (ROPS) (tractor cab or roll-bar) and seat belt to protect the operator from falling off the tractor, especially during a roll over where the driver could be crushed and killed. Only operate the tractor with the ROPS in the raised position and seat belt fastened. Tractor model not equipped with a ROPS and seat belt should have these life saving features installed by an authorized dealer. OPS-U- 0003

(SG-7)

3. TRACTOR REQUIREMENTS

Operating the blade with a tractor that does not meet the following requirements may cause tractor or blade damage and be a potential danger to the operator and passersby.

Tractor Requirements and Capabilities

• ASABE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt.

• Tractor Safety Devices ....................Slow Moving Vehicle (SMV) emblem, lighting, PTO master shield

• Tractor Horsepower (Drawbar):

- Front Wheel .........................12’ - 300 HP, 14’ - 250 HP

• Hitch - 3 Point Hitch.........................CAT III-IV and QH

- Lifting Capacity ....................12’- 3463 lbs., 14’- 3603 lbs.

• Front End Weights............................As needed to maintain 20% weight on front axle

OPERATION

3.2 T ractor Horsepower

The power required to operate a blade is determined by the tractor PTO horsepower. For most operating conditions, the 300 Series rear blade requires a tractor with at least 300 HP for 12’ and 250 HP for 14.’ Operating the blade with a tractor that does not have adequate power may damage the tractor engine. Exceeding the recommended horsepower may cause blade damage by overpowering the unit in heavy operating conditions.

300 Series 09/10 Operation Section 4-5

Page 36

OPERATION

3.4 Front End Weight

A minimum of 20% total tractor weight must be maintained on the tractor front end at all times. Front end weight is critical to maintain steering control and to prevent the tractor from rearing up while driving. If the front end is too light, add weight until a minimum of 20% total weight is reached on the front tires. Front weights and weight carriers can be purchased throug h an authorized tractor dealership. OPS-U- 0005

4. GETTING ON AND OFF THE TRACTOR

Before getting onto the tractor, the operator must read and completely understand the implement and tractor operator manuals. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. OPS-U- 0007

Do not mount or dismount the Tractor while the tractor is moving. Mount the Tractor only when the Tractor and all moving parts are completely stopped.

(SG-12)

3.3 T ractor 3-Point Hitch

The tractor 3-point hitch must be rated to lift at least 3463 lbs. for the 12’ and 3603 lbs. for the 14’.

The 300 Series can attach to tractor’s with either a CAT III or IV hitch. Refer to the tractor operator’s manual for the category of the tractor used. If the hitch does not conform to the ASABE CAT III or IV dimensions, the blade may not fit or raise properly. Consult an authorized dealer for possible modification procedures to mount nonconforming hitches.

Use the correct hitch pins for the hitch category being used. For a Cat III hitch, 1-1/8” lower and a 1” upper diameter hitch pins are used and Cat IV hitches require 1-7/16” lower and a 1-1/4” upper diameter hitch pins.

OPERATION

CAT III Implement / Hitch Specification CAT IV Implement/ Hitch Specification

Width from outside to outside A-frame...............38” Width from outside to outside A-frame........45-15/16”

Quick Hitch width inside lug to lug ..............39-1/4” Quick Hitch width inside lug to lug ..................47-1/4”

Height from bottom hitch pin to top pin..............22” Height from bottom hitch pin to top pin .................27”

Lower pin diameter ......................................1-7/16” Lower pin diameter............................................1-3/4”

Upper pin diameter ................................... ... .1-1/4” Upper pin diameter............................................1-3/4”

Linch pin diameter ........................................15/32” Linch pin diameter............................................ 11/16”

300 Series 09/10 Operation Section 4-6

Page 37

OPERATION

4.1 Boarding the Tractor

Use both hands and equipped handrails and steps for support when boarding the tractor. Never use control levers for support when mounting the tractor. Seat yourself in the operator’s seat and secure the seat belt around you.

Never allow passengers to ride on the tractor or attached equipment. Riders can easily fall off and be seriously injured or killed from falling off and being ran over. It is the operator’s responsibility to forbid all extra riders at all times. OPS-U- 0008

(SG-11)

Never allow children or other persons to ride on the Tracto r or Implement. Falling off can result in serious injury or death.

(SG-10)

4.2 Dismounting the Tractor

Before dismounting, park the tractor and implement on a reasonably level surface, apply the parking brake, idle the engine down, disengage the PTO, and lower the implement to the ground. Shut down the tractor engine according to the operator’s manual, remove the key, and wait for all motion to completely stop. Never leave the seat until the tractor , its engine and all moving parts have come to a complete stop.

Use hand rails and steps when exiting the tractor. Be careful of your step and use extra caution when mud, ice, snow or other matter has accu mu la te d o n t he st eps or han d r ails . Us e a ll ha n dr ails an d s te ps for su ppor t and never rush or jump off the tractor. OPS-U- 0009

(SG-9)

OPERATION

300 Series 09/10 Operation Section 4-7

Page 38

OPERATION

5. STARTING THE TRACTOR

The operator must have a complete underst anding of the placement, function, and operationa l use of all tractor controls before starting the tractor. Review the tractor operator’s manual and consult an authorized dealer for tractor operation instructions if needed.

Essential Tractor Controls:

• Locate the ignition switch

• Locate the light control lever

• Locate the engine shut off control

• Locate the engine throttle control

• Locate the brake pedals and the clutch

• Locate the parking brake

• Locate the PTO control

• Locate the 3-point hitch control lever

• Locate the hydraulic remote control levers Before starting the tractor ensure the following:

• Conduct all pre-start operation inspection and service according to the tractor operator’s manual.

• Make sure all guards, shields, and other safety devices are securely in place.

• The parking brake is on.

• The 3-point hitch control lever is in the lowered position.

• The hydraulic remote control levers are in the neutral position.

• The tractor transmission levers are in park or neutral. Refer to the tractor owner’s manual for tractor starting procedures. Only start the tractor while seated and

belted in the tractor operator’s seat. Never bypass the ignition switch by short circuiting the starter solenoid. After the tractor engine is running, avoid accident al contact with the tractor transmission to prevent sudden and

unexpected tractor movement. OPS-0010_B

Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health.

(SG-23)

Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operators manual for proper starting instructions.

(SG-13)

OPERATION

300 Series 09/10 Operation Section 4-8

Page 39

OPERATION

6. CONNECTING THE REAR BLADE TO THE TRACTOR

Use extreme caution when connecting the blade to the tractor. The rear blade should be securely resting at ground level or set on blocks. Keep hands and feet from under the blade and clear of pinch points between the tractor hitch arms and blade pins. OPS-0011_A

Always shut the Tractor completely down, place the transmission in park, and set the parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches.

(S3PT-15)

(SG-14)

6.1 Connecting the Rear Blade

1. Shor ten or remo ve the tractor drawba r to avoid interference when raising and lowering the rear blade.

2. Board the tractor and start the engine. Position the tractor to the blade with the 3point lift arms positioned between the respective set of blade A-frame lift lugs. Note:

Set the 3-point lift control to “Position Control” so that the lift arms maintain a constant height when attaching the blade. See the tractor Operator’s Manual for correct settings when attaching 3-point equipment.

3. Turn off the tractor engine, set the parking brake, place the tractor in park, and dismount.

4. One lift arm at a time, align arm end hole between the set of holes of A-frame lift lugs. Insert hitch pin through the lug and ar m holes and insert retaining pin into hitch pin. Walk around to opposite side and repeat procedure for remaining lift arm and hitch pin.

5. Extend or retract the 3-point top link to align its end hole with the holes of the blade’s top link. Insert the top link pin and retain with the lynch pin.

6. Adjust any lower link check chains, guide blocks, or sway blocks to prevent the blade from swaying side to side and possible contact with tractor rear tires.

OPERATION

300 Series 09/10 Operation Section 4-9

Page 40

OPERATION

7. PRE-OPERATION INSPECTION AND SERVICE

Before each use, a pre-operation inspection and service of the implement and tractor must be performed. This includes routine maintenance and scheduled lubrication, inspecting that all safety devices are equipped and functional, and performing needed repairs. DO NOT operate the unit if the pre-operation inspection reveals any condition affecting safe operation. Perform repairs and replacement of damaged and missing parts as soon as noticed. By performing a thorough pre-operation inspection and service, valuable down time and repair cost can be avoided. OPS-U-0029

(SG-21)

7.1 Tractor Pre-Operation Inspection/Service

Refer to the tractor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed according to the manufacturers recommendations. The following are some of the items that require daily service and inspection:

• Tire condition/air pressure

• Wheel lug bolts

• Steering linkage

• PTO shield

• SMV sign is clean and visible

• Tractor’s lights are clean and functional

• Tractor Seat belt is in good condition

• Tractor ROPS is in good condition

• ROPS is in the raised position

• No tractor oil leaks

• Radiator free of debris

• Engine oil level and condition

• Engine coolant level and condition

• Power brake fluid level

• Power steering fluid level

• Fuel condition and level

• Sufficient lubrication at all lube points

• Air filter condition OPS-U-0030

OPERATION

300 Series 09/10 Operation Section 4-10

Page 41

OPERATION

The operator’s manual and safety signs affixed on the unit contain important instructions on the safe and proper use of the equipment. Maintain these important safety features on the implement in good condition to ensure the information is available to the operator at all times.

• Ensure the manual canister is secured to the equipment with the operator’s manual inside.

• Ensure all safety signs are in plac e and legible . Replace missing, damaged, and illegible decals. OPS-U- 0011

7.2 Blade Pre-Operation Inspection/Service

Before each blade use, a complete inspection and service is requ ired to en sure the blad e is in a go od and safe working condition. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure the blade is ready for operation, conduct the following. OPS- 0020_A

OPERATION

300 Series 09/10 Operation Section 4-11

Page 42

OPERATION

Blade & Box Blade PRE-OPERATION Inspection

Blade ID#:_______________________Make:__________________________

Date: ___________________________Shift:___________________________

Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the blade is resting on the ground or securely blocked up and all hydraulic pressure has been relieved.

Operator’s Signature:_____________________________________________________

Item

Condition at

Start of Shift

Specific Comments if

not O.K.

The Operator’s Manual is in the Canister. All Safety Decals are in place and legible. The Hitch connection pins are properly retained. There are no cracks in Hitch. All frame bolts are in place and tight. The blade swing, angle & tilts pins are properly lubricated and retained. The Blade edge & moldboard are clear of mud and debris. The blade edge attachments bolts are in place and tight. The blade edge is not chipped, cracked or bent. The Storage Stands are in place & in good condition. The skid shoes are in good condition. The Hydraulic Cylinders pins are in place & retained. There are no leaking or damaged hoses. There is no evidence of Hydraulic leaks. The gauge wheel(s) are in good condition & lubricated. The scarifier shanks are properly retained. The scarifier points are in good condition and retained.

DO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT

OPERATION

300 Series 09/10 Operation Section 4-12

Page 43

OPERATION

Tractor PRE-OPERATION Inspection

Tractor ID#:________________________Make:________________________

Date:______________________________Shift:________________________

Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the implement is resting on the ground or securely blocked up and all hydraulic pressure has been relieved.

Operator’s Signature:___________________________________________________

Item

Condition at

Start of Shift

Specific Comments if

not O.K.

The flashing lights function properly The SMV Sign is clean and visible The tires are in good condition with proper pressure The wheel lug bolts are tight The tractor brakes are in good condition The steering linkage is in good condition There are no visible oil leaks The hydraulic controls function properly The ROPS or ROBS Cab is in good condition The seatbelt is in place and in good condition The 3-point hitch is in good condition The drawbar pins are securely in place The PTO master shield is in place The engine oil level is full The brake fluid level is full The power steering fluid level is full The fuel level is adequate The engine coolant fluid level is full The radiator is free of debris The air filter is in good condition

DO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT

OPERATION

300 Series 09/10 Operation Section 4-13

Page 44

OPERATION

(S3PT-12)

Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this

equipment at high speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment. Make sure you abide by the following rules:

Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce you r speed. When operating in traffic always use the Tractor’s flashing warning lights and red uce your speed. Be a ware of traf fic around yo u and watch out for the other guy.

(SG-19)

8. DRIVING THE TRACTOR AND IMPLEMENT

Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle the weight of the implement and the tractor operating controls are set for safe transport. To ensure safety while driving the tractor with an attached implement, review the following. OPS-U- 0012

OPERATION

300 Series 09/10 Operation Section 4-14

Page 45

OPERATION

8.1 Starting the Tractor

The procedure to start the tractor is model specific. Refer to the tractor operator’s manual for starting procedures for your particular tractor. Consult an authorized dealer if the starting procedure is unclear. Ensure the 3-point control lever is in the lowered position and the PTO is disengaged before starting the tractor. OPS-U-0033

8.2 Brake and Differential Lock Setting

Make sure the tractor brakes are in good operating condition. Tractor brakes can be set to operate independently allowing single rear wheel braking action or locked together to provide simultaneous rear wheel braking. FOR MOST DRIVING AND OPERATING CONDITIONS, THE BRAKE PEDALS SHOULD BE LOCKED TOGETHER TO PROVIDE THE MOST EFFECTIVE BRAKING ACTION.

Always disengage the tractor differential lock when turning. When engaged the differential lock will prevent or limit the tractor from turning. During normal cutting conditions, locking the differential provides no benefit and should n ot be used. OPS-

U- 0013

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes. When operating down a hill or on wet or rain slick roads, the braking distance increases; use extreme care and reduce your speed in these conditions. When operating in traffic, always use the Tractor’s flashing warning lights and red uce your speed. Be aware of tr affic around you and watch out for the other guy.

OPERATION

300 Series 09/10 Operation Section 4-15

Page 46

OPERATION

8.3 Driving the Tractor and Blade

Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the tractor and blade. Moving slowly at first will also prevent the tractor from rearing up and loss of steering control. The tractor should never be operated at speeds that cannot be safely handled or which will prevent the operator from stopping quickly during an emergency. If the power steering or engine ceases operating, stop the tractor immediately as the tractor will be difficult to control.

Perform turns with the tractor and blade at slow speeds to determine how the tractor with an attached implement handles a turn. Determine the safe speed to maintain proper control of the tractor when making turns. When turning with an implement, the overall working length of the unit is increased. Allow additional clearance for the blade when turning.

To avoid overturns, drive the tractor with care and at safe speeds, especially when operating over rough ground, crossing ditches or slopes, and turning corners. Tractor wheel tread spacing should be increased when working on inclines or rough ground to reduce the possibility of tipping.

Use extreme caution when operating on steep slopes. Keep the tractor in a low gear when going downhill. DO NOT coast or free-wheel downhill. OPS- 0037_A

9. OPERATING THE TRACTOR AND IMPLEMENT

THE OPERATOR MUST COMPLETELY UNDERSTAND HOW TO OPERATE THE TRACTOR AND IMPLEMENT AND ALL CONTROLS BEFORE ATTEMPTING TO OPERATE. The operator must read and

understand the Safety and Operation Sections of the implement and tractor operator’s manuals. These manuals must be read and explained to any operator who cannot read. Never allow someone to operate the implement and tractor without complete operating instructions.

Before starting any operation, the operator must become familiar with the area to be worked in and any obstacles and hazards contained within to ensure safety to the operator, bystanders, and equipment. Special attention should be paid to foreign debris, ro ugh terr ain, steep slopes, and p assersby and an imals in the area.

OPS-U- 0015

OPERATION

300 Series 09/10 Operation Section 4-16

Page 47

OPERATION

10. Operating the Blade

Only operate the blade from the tractor operator’s seat with the seatbelt securely fastened. The tractor must be equipped with a ROPS in the raised position or a ROPS cab.

Ditching (V -Type Ditch)

Tilt the Moldboard to the desired ang le (15 degrees or less) down on the right (lef t) by use of the Moldb oard Tilt Cylinder.

Adjust the Moldboard Pivot and Mainframe Swing to place the right (left) corner of the Blad e directly behind the right (left) rear tire with a 45 degree to 60 degree angle between the Blade and a line parallel to the rear Axle. The combined adjustments of the Moldboard Pivot and Mainframe Swing will give this angle. For example, to obtain a 45 degree Blade Angle, rotate the Moldboard 15 degrees and swing the Mainframe 30 degrees, or rotate the Moldboard 30 degrees and swing the Mainframe 15 degrees depending on tractor tire spacing.

For light ditching, cleaning out ditches, and snow removal, operate the tractor at slow speeds, and be careful not to hit any hidden objects. Operating with a light load on the Blade or at high speeds will subject the Blade to severe damage from the impact load if a solid object is hit.

NOTE: Never rotate Blade Tilt, Carrier Pivot, or Mainframe Pivot with hydraulics while Blade is under load. This will cause excessive load on pins and shafts which will result in damage to Blade. Remove load from Blade and then rotate.

To refill a ditch, offset the mainframe to the right (left) and rotate the Moldboard to push the dirt into the ditch while traveling forward.

Utility

To clean close to a fence or barn, offset the Moldboard to the right or lef t to extend the Blade beyond the tractor tire. Be careful not to hang the Blade Tip as this could result in damage to the Blade or Moldboard. For smoothing out loose soil, a fine finish can be obtained by pushing the soil with the back of the Moldboard.

Grading

Grading can be accomplished with the use of the Planer Wheel (Accessory Equipment). Set the Moldboard Pivot to the desired angle, lower the Blade to the ground, and then set the depth of cut with the Hydraulic Cylinder. Do not drop the Planer Wheel on the ground. This could result in damage to the Planer Wheel or Hydraulic Cylinder.

OPERATION

Backfilling

The Moldboard can be manually rotated 180 degrees for backfilling operations. This position requires a careful setting of the Top Link allowing a Blade angle which does no t tend to bury itself, but move across the top of the ground. Backfilling is a very critical operation because the Blade tends to dig into the ground. The backfilling operation should be performed with the Mainframe straight behind the tractor with the Blade set in the center position (perpendicular to the Mainframe). The work should be kept in the center of the Blade. Avoid concentrated loads on the end o f the Blade. Do not ram into a load at any time as this multiplies the forces several times normal and could result in damage to your Blade. Perform all backfilling operations at slow speeds to prevent damage if the Blade hits an object. Moving snow with the Blade in the backfill position is a very delicate operation and should be performed with care. It is very easy to hit hidden objects when moving the light snow. It is also very easy to operate the Blade at too high a speed, with resulting damage.

NOTE: The warranty shall not apply to damage caused by misuse, abuse, or contact with obstructions.

300 Series 09/10 Operation Section 4-17

Page 48

OPERATION

10.1 Shutting Down the Implement

Park the tractor on a level surface, place the transmission in park or neutral and apply the parking brake, lower the attached implement to the ground, shut down the engine, remove the key, and wait for all motion to come to a complete stop before exiting the tractor. OPS-BL- 0002

11. DISCONNECTING THE BLADE FROM THE TRACTOR

Before disconnecting the blade, all movement must cease. Move the blade to a level storage location and lower the unit to the ground. If the blade is not resting securely on the ground, block the blade up securely before attempting to disconnect it from the tractor.

Use extreme care to keep feet and hands from under the blade and clear of any pinch points. OPS- 0051_A

Always shut the Tractor completely down, place the transmission in park, and set the parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches.

(S3PT-15)

When disconnecting the blade the tractor should be completely shut down and secured in position, by lowering the parking jack. Relieve hydraulic pressure by moving the control levers back and forth several times. Then extend the tractor 3-point hitch top link to remove tension on the top link hitch pin. When the pin is loose and easy to rotate, remove the pin from the blade. Next remove both lower hitch pins. OPS- 0052_C

OPERATION

300 Series 09/10 Operation Section 4-18

Page 49

OPERATION

12. BLADE STORAGE

Properly preparing and storing the blade at the end of the season is critical to maintaining its appearance and to help ensure years of dependable service. The following are suggested storage procedures:

• Thoroughly clean all debris off the blade to prevent damage from rotting grass and standing water.

• Lubricate all blade grease points and fill gearbox oil levels as detailed in the maintenance section.

• Tighten all bolts and pins to the recommended torque.

• Check the blade for worn and damaged parts. Perform repairs and make replacements immediately so that the blade will be ready for use at the start of the next season.

• Store the blade in a clean, dry place with the blade resting securely on blocks or at ground level.

• Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the blade. OPS-0053_D

(SG-25)

13. TRANSPORTING THE TRACTOR AND IMPLEMENT

Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind when you finish working in an area. Therefore, the operator mu st emp loy g ood judge men t and sa fe op eration practices when transporting the tractor and implement between locations. By using good judgement and following safe transport procedures, the possibility of accidents while moving between locations can be substantially minimized. OPS-U- 0017

Never allow children or other persons to ride on the Tracto r or Implement. Falling off can result in serious injury or death.

(SG-10)

OPERATION

When transporting, only raise the blade enough to clear ground obstacles to prevent tipping, especially when traveling through rough terrain.

300 Series 09/10 Operation Section 4-19

Page 50

OPERATION

Before transporting the tractor on a public roadway or boarding a trailer for transport, t he tractor brake pedals should be locked together. Locking the pedals ensures that both wheels brake simultaneously while stopping, especially when making an emergency stop.

Use extreme caution and avoid hard applications of the tractor brakes when towing heavy loa ds at road speeds. Never tow the implement at speeds greater than 20 MPH (25 kph). OPS-U- 0018

13.1 Transporting on Public Roadways

Extreme caution should be used when transporting the tractor and impl ement on public roadways. The tractor must be equipped with all req uired safety warning features including a SMV emble m and flashing warning lights to alert drivers of the tractor’s presence. Remember that roadways are primarily designed for automotive drivers and most drivers will not be looking out for you, therefore, you must look out for them. Check your side view mirrors frequently and remember that vehicles will approach quickly because of the tractor’s slower speed. Be extremely cautious when the piece of equipment that you are towing is wider than the tractor tire width and/or extends beyond your lane of the road.

Make sure that a proper size safety tow chain is secured between the tractor and implement before entering a public road. OPS-U- 0019

Only tow the Implement behind a properly sized and equipped Tractor which exceeds the weight of the Implement by at least 20%. DO NOT tow the Implement behind a truc k or ot her t ype o f vehic le. N ever tow the Implement and another Implement connected in tandem. Never tow the Implement at speeds over 20 MPH.

(STI-06)

Never allow children or other persons to ride on the Tracto r or Implement. Falling off can result in serious injury or death.

(SG-10)

(SG-6)

OPERATION

300 Series 09/10 Operation Section 4-20

Page 51

OPERATION

The SMV (Slow-Moving Vehicle) emblem is universal symbol used to alert drivers of the presence of equipment traveling on roadways at a slow speed. SMV signs are a triangular bright orange with reflective red trim for both easy day and night visibility. Make sure the SMV sign is clean and visible from the rear of the unit before transporting the tractor and implement on a public roadway. Replace the SMV emblem if faded, damaged, or no longer reflective. OPS-U- 0020

Make sure that all tractor flashing warning lights, headlights, and brake/tail lights are functioning properly before proceeding onto public roads. While newer model tractors have plenty of lighting to provide warning signals and operating lighting, most older models are only equipped with operating lights. Consult an authorized tractor dealer for lighting kits and modifications available to upgrade the lighting on older tractor models. OPS-U- 0021

When operating on public roads, have consideration for other road users. Pull to the side of the road occasionally to allow all following traffic to pass. Do not exceed the legal speed limit set in your country for agricultural tractors. Always stay alert when transporting the tractor and implement on public roads. Use caution and reduce speed if other vehicles or pedestrians are in the area. OPS-

B- 0022

OPERATION

300 Series 09/10 Operation Section 4-21

Page 52

OPERATION

Reduce speed before turning or applying the brakes. Ensure that both brake pedals are locked together when operating on public roads. OPS-U- 0023

13.2 Hauling the Tractor and Implement

Before transporting a loaded tractor and implement, measure the height and width dimensions and gross weight of the complete loaded unit. Ensure that the load will be in compliance with the legal limits set for the areas that will be traveled through. OPS-U- 0024

Use adequately sized and rated trailers and equipment to transport the tractor and implement. Consult an authorized dealer to determine the proper equipment required. Using adequately sized chains, heavy duty straps, cables and/or binders, securely tie down both the front and rear of the tractor utilizing the proper tie down locations as specified by the tractor manufacturer. OPS-U- 0025

OPERATION

300 Series 09/10 Operation Section 4-22

Page 53

OPERATION

Arrange the chains so that when tightened, the chains are pulling downward and against themselves. Carefully tighten the securing chains or other fasteners using boomers or binders to apply maximum tension. Use extreme care when attaching and removing the securing devices as the extreme tension involved when released has the potential to inflict serious injury.

While hauling the tractor and implement, make occasional stops to check that the tractor and implement have not moved or shifted and that the securing chains have maintained tension. If during transport a hard braking, sharp turn ing, or swerving action was performed, stop at the next sa fe location to inspect the security of the load. OPS-U- 0026

OPERATION

300 Series 09/10 Operation Section 4-23

Page 54

OPERATION

14. TROUBLESHOOTING GUIDE

Problem Possible Cause Remedy

Shearing M/B Carrier Lack of lubrication Lubricate Pivot Pin

Pivot Pin Bolt Bolt not tightened properly Tighten Bolt to proper torque

Bent Moldboard Small curve is normal from weld pull Can be removed but will not

affect operation

Hitting hidden objects Know soil conditions, keep

speed to a minimum.

OPERATION

Blade will not penetrate soil Cutting edge dull Replace Cutting edge

Blade set to straight Increase Top Link length Soil too hard Use scarifiers to loosen soil

A-Frame bent Hitting hidden objects in the backfill Use slow speed when in unknown

position soil conditions

Moldboard digging in too Blade pitch excessive Adjust Top Link much Soft ground. Install Gauge Wheel.

Install Skid Shoes.

Unable to hold level ground Tractor and Blade following contour Install Gauge Wheel

Tractor Draft Control lifting Blade Set Tractor Draft Control

Hydraulic Cylinder(s) Not enough pressure Check pressure will not operate Valve not connected properly Re-plumb V alve

Quick Coupler not completely Complete connection connected

300 Series 09/10 Operation Section 4-24

Page 55

OPERATION

Problem Possible Cause Remedy

Hydraulic Pump not shutting Using Open Center Valve Replace Valve or Conversion Plug off on Closed Center System and Main Relief

Open Center Conversion Plug Replace with Closed Center Plug Pumping over Relief Valve Replace with No Relief Plug

Oil leaking at hose Connection not tight Tighten connection connection Did not use sealant Apply a good sealant to connection

Connection cracked from Replace cracked connection over-tightening Mismatched Connection threads Use correct connectors or types.

OPERATION

300 Series 09/10 Operation Section 4-25

Page 56

Page 57

MAINTENANCE SECTION

Maintenance Section 5-1

Page 58

MAINTENANCE

Lubrication

The Bush Hog 300 Series is a rugged, dependable Blade that should perform satisfactorily with the following preventive maintenance:

Lubricate the Moldboard Pivot Pin (Figure Asm-

0001), the Moldboard Tilt Pin (Figure Asm-0002), and Mainframe Swing Pin on the A-Frame after every 10 hours of operation. Decals are placed in locations about the implement indicating locations of Grease Fittings.

Replace excessively worn Grader Blade when ditching. A badly worn cutting edge increases the strain on the Blade and the Tractor and reduces efficiency.

If the Gauge Wheel is used, a Grease Fitting is provided at the Caster Pivot location and on Wheel

MAINTENANCE

Hub.

300 Series 09/10 Maintenance Section 5-2

Page 59

MAINTENANCE

Proper Torque For Fasteners

The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer to this chart to determine the grade of bolts and the proper torque except when specific torque values are assigned in manual text.

Recommended Torque in Foot Pounds Unless Otherwise Stated in the Manual*

NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal engine oil. They do not apply if special g raphited or moly disulphide grea ses or other ex treme pressur e lubricants are used. This applies to both UNF fine and UNC coarse threads.

MAINTENANCE

300 Series 09/10 Maintenance Section 5-3

Page 60

LIMITED WARRANTY



Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the rep air or r eplacement of defective part s.

Replacement or repair part s inst alled in the equipm ent covered by this limited warranty a re warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hou rs. Bush Hog res erves the right to inspect an y equipment or parts which are claimed t o have been defective in material or workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog.

THIS LIMITED WARRANTY SHALL NOT APPLY:

1. To vendor items which carry their own warranties, such as engines, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability.

4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.

6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA 36703.



Record the model number, serial number and date purchased. This information will be helpful to your dealer if parts or service are requir ed.

MODEL NUMBER __________________________ _____ _ SERIAL NUMBER _______________________________ _

MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA

DATE OF RETAIL SALE ___________________________

Page 61

TO THE OWNER/OPERATOR/DEALER

To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly id entifies each section where y ou can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and

2. Provide Seat belts that meet the requirements of this paragraph of this Standard and SAE J4C; and

3. Ensure that each employee uses such Seat belt while the tractor is moving; and

4. Ensure that each employee tightens the Seat belt sufficiently to confine the employee to the protected area provided by the ROPS

REQUIRED OF THE OPERATOR:

1. Securely fasten seat belt if the tractor has a ROPS.

2. Where possible, avoid operating the tractor near ditches, embankm ents, and holes.

3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.

4. Stay off slopes too steep for safe operation.

5. Watch where you are going - especially at row ends, on roads, and around trees.

6. Do not permit others to ride.

7. Operate the tractor smoothly - no jerky turns, starts, or stops.

8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.

9. When the tractor is stopped, set brakes securely and use park lock, if available.

 Keep children away from danger all day, every day...

 Equip tractors with rollover protection (ROPS) and keep

all machinery guards in place...

 Please work, drive, play and live each day with care

and concern for your safety and that of your family and fellow citizens.

Page 62

300 Series

Rear Mounted Blade

300 Series - SOM - 09/10 P/N 00786978C Printed U.S.A

Bush Hog 300 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

300 Series

REAR MOUNTED BLADE

OPERATOR’S MANUAL

BUSH HOG®

To the Owner/Operator/Dealer

TABLE OF CONTENTS

SAFETY SECTION

Safety Messages

Decal Location

1. 00725746 1 PELIGRO Translate Safety Material

2. 02965262 1 WARNING Oil Penetration

3. 00786980 1 IMPORTANT Genuine Bush Hog Parts

4. 999000 1 WARNING Multi-Hazard for Blades

5. 999200 1 WARNING Multi-Hazard General

6. 03200347 * REFLECT SMV Emblem

7. 000678 2 INSTRUCT Grease Fitting Inside

8. 00763977 1 INSTRUCT Notice to Owner

9. 00786979 3 LOGO Bush Hog

10. 00786984 1 NAME 300-12

11. nfs 1 SER PLT Serial Plate

12. 1458393 2 REFLECT Amber Reflectors

13. 1458392 4 REFLECT Red Reflectors

14. 1458398 4 REFLECT Fluorescent

15. 49722 1 _________ Canister, Operator’s Manual

16. 00786978C 1 MANUAL Operator’s Manual

Decal Description

Federal Laws and Regulations

INTRODUCTION SECTION

ASSEMBLY SECTION

Assembly of Moldboard to Mainframe

1. Attach Moldboard T ilt Cylinder with the Rod End attached to the Moldboard.

2. Attach the Moldboard Pivot Cylinder.

3. Attach the Mainframe Swing Cylinder.

Gauge Wheel (Extra Equipment)

Skid Shoes & Quick Tack End Plates (Extra Equipment)

Hydraulic System

Hydraulic Control Valve (Accessory Equipment)

Selector Valve (Accessory Equipment)

OPERATION SECTION

1. Standard Equipment and Specifications

2. OPERATOR REQUIREMENTS

3.1 ROPS and Seat Belt

3. TRACTOR REQUIREMENTS

3.2 T ractor Horsepower

3.4 Front End Weight

4. GETTING ON AND OFF THE TRACTOR

3.3 T ractor 3-Point Hitch

4.1 Boarding the Tractor

4.2 Dismounting the Tractor

5. STARTING THE TRACTOR

6. CONNECTING THE REAR BLADE TO THE TRACTOR

6.1 Connecting the Rear Blade

1. Shor ten or remo ve the tractor drawba r to avoid interference when raising and lowering the rear blade.

3. Turn off the tractor engine, set the parking brake, place the tractor in park, and dismount.

5. Extend or retract the 3-point top link to align its end hole with the holes of the blade’s top link. Insert the top link pin and retain with the lynch pin.

6. Adjust any lower link check chains, guide blocks, or sway blocks to prevent the blade from swaying side to side and possible contact with tractor rear tires.

7. PRE-OPERATION INSPECTION AND SERVICE

7.1 Tractor Pre-Operation Inspection/Service

7.2 Blade Pre-Operation Inspection/Service

8. DRIVING THE TRACTOR AND IMPLEMENT

8.1 Starting the Tractor

8.2 Brake and Differential Lock Setting

8.3 Driving the Tractor and Blade

9. OPERATING THE TRACTOR AND IMPLEMENT

10. Operating the Blade

Ditching (V -Type Ditch)

Utility

Grading

Backfilling

10.1 Shutting Down the Implement

11. DISCONNECTING THE BLADE FROM THE TRACTOR

12. BLADE STORAGE

13. TRANSPORTING THE TRACTOR AND IMPLEMENT

13.1 Transporting on Public Roadways

13.2 Hauling the Tractor and Implement

14. TROUBLESHOOTING GUIDE