The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong
to the basic machine featured in this manual. Part Numbers and Descriptions are given
to help locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the
machine for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct
part number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applic able.
5. Some parts are unlisted items which are special production items not normally stocked
and are subject to special handling. Request a quotation for such parts before sending
a Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
For maximum safety and to guarantee optimum product reliability, always
use genuine BUSH HOG Parts. The use of inferior replacement parts may
causepremature or catastrophic failure which could result in serious injury
or death.Direct any questions regarding parts to:
BUSH HOG
2501 Griffin Ave.
Selma, AL 36703
www.bushhog.com
Contact Us
800-304-2836
Page 3
Page 4
LIMITED WARRANTY
Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorize d Bush
Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for
non-commercial, state and municipalities’ use and ninety (90) days for commercial usefrom date of retail sale. The
obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective
parts.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety
(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty
period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog
dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are
claimed to have been defective in material or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or
expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items
warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges
other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges
for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment,
expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond
the control of Bush Hog.
THIS LIMITED WARRANTY SHALL NOT APPLY:
1. To vendor items which carry their own warranties, such as engines, tires, and tubes.
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.
3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement
of Bush Hog such use affects its performance, stability or reliability.
4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the
sole judgement of Bush Hog, affects its performance, stability or reliability.
5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn
blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.
6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the
company’s sole judgement is a wear item.
NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED
WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN
WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA
36703.
Record the model number, serial number and date
purchased. This information will be helpful to your
dealer if parts or service are required.
MAKE CERTAIN THE WARRANTY
HAS BEEN FILED WITH BUSH HOG
SELMA, ALABAMA
MODEL NUMBER ________________________________
SERIAL NUMBER ________________________________
DATE OF RETAIL SALE ___________________________
Material Bucket - Pin on...............................................................................................................................................................1-33C-1
60” 4 in 1 Bucket Assembly 2-7129 - Pin on................................................................................................................................1-33C-2
60” 4 in 1 Bucket Assembly 2-6708 - Quick Attach......................................................................................................................1-33C-3
Material Bucket - Quick Attach.....................................................................................................................................................1-33C-4
Frame Kit 2-5317 New Holland 1510...........................................................................................................................................1-33C-8
Hydraulic System .........................................................................................................................................................................1-33D-1
Valve Assembly ( Prince LVR Parallel).........................................................................................................................1-33D-2, 1-33D-3
Valve Assembly ( Prince LVS Series)...........................................................................................................................1-33D-4, 1-33D-5
Hose Kit 2-5339 New Holland 1310, 1510, 1710 & 1910.............................................................................................................1-33E-1
Valve Kit 2-6314 New Holland 1720 & 1920..................................................................................................................1-33F-2, 1-33F-3
Valve Kit 2-6337 New Holland TC30, T1510, T1520, 1320, 1520, 1620HST & 1715 .................................................1-33F-4, 1-33F-5
Valve Kit 2-6393 New Holland 1310, 1510 & 1710....................................................................................................1-33F-12, 1-33F-13
Valve Kit 2-6397 Case IH 244, 245, 254 & 255 .........................................................................................................1-33F-14, 1-33F-15
Valve Kit 2-6413 New Holland 1910 ..........................................................................................................................1-33F-22, 1-33F-23
Valve Kit 2-6452 Case IH D25, DX25, D29, DX29, DX31, D33, DX33, DX34, and Farmall 31,35
New Holland 1530, 1630, 1725, 1925, TC25, TC25D, TC29, TC29D, TC29DA, TC31DA, TC33,
952107-1Pin,1 x 4"2
1047046Bolt, Shoulder, 3/8 x 1"6
11------Capscrew, 5/16-18 x 1-3/4"6
12------Capscrew, 5/16-18 x 1-1/4"1
13------Locknut, 5/16-187
1400003500Fitting, Grease, Straight, 1/8-2712
1550069071Decal, Model 22972
1650057411Decal, Bush Hog 14.5"2
17D468Decal, Danger-Multi-Hazard2
1800786980Decal, Genuine Bush Hog Parts1
1951906Decal, Danger/Peligro1
1-33A-1
Page 10
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
2297 SUBFRAME
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
1------Side Frame, Left, With Decals1
2------Side Frame, Right, With Decals1
351647Bumper, Loader Front1
444104Hinge, Loader Upright2
544105Bolt, Tee, Loader Hinge2
652107-4Pin, 1 x 5-1/4"2
751965-2Pin, 1 x 3-5/8"2
841902-27Pin, Clevis, 1/2 x 4-1/2"1
941901-1Pin, Cotter, .148 x 2-11/16"1
10------Carriage Bolt, 5/8-11 x 5"2
1147046Bolt, Shoulder, 3/8 x 1"6
12------Capscrew, 1/2-13 x 4"1
13------Capscrew, 5/16-18 x 1-3/4"6
14------Screw, Self Tapping, 1/4 x 3/4"2
15------Flatwasher, 5/86
16------Hex Nut, 5/8-112
17------Locknut, 5/8-112
18------Locknut, 1/2-131
19------Locknut, 3/8-166
20------Locknut, 5/16-187
2100003500Fitting, Grease, Straight, 1/8-2712
2200776031Canister With Cap, Includes Seal1
2300776964Seal, Manual Canister1
2446778Decal, Danger, Do Not Work Under Raised Loader 2
2551900Decal, Danger, Prevent Rollovers1
26D469Decal, Warning-General Safety1
2748280Decal, Caution, Universal One Call1
2852740Decal, Warning, Do Not Operate With Oil Leaks2
29D471Decal, Warning-Injury Or Death1
1-33A-2
Page 11
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-5323
Kubota L235, L235DT, L275, L275DT
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
136662Bracket, Front Mounting1
2------Capscrew, Metric, M12-1.25 x 3010
3------Lockwasher, 1/210
436663Bracket, Mid Mounting1
531501Spacer, 3-1/2 Lg.1
631502Spacer, 3-7/8 Lg.1
7------Flatwasher, 5/88
8------Lockwasher, 5/88
9------Capscrew, Metric, M14-1.5 x 30 (LH Side)4
10------Capscrew, Metric, M14-1.5 x 45 (RH Side)4
11------Flatwasher, 1/24
1-33B-1
Page 12
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-5325
Case IH 244 & 254
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
136329Bracket, Front Mounting1
2------Capscrew, 5/8-11 x 1-3/44
336328Flat, Spacer (For Use Without Belly Mower)2
4------Lockwasher, 1/212
5------Capscrew, Metric, M12-1.25 x 4012
636315-1Bracket, Left Reinforcing1
736315-2Bracket, Right Reinforcing (Not Shown)1
8------Locknut, 1/28
9------Capscrew, Metric, M14-2.0 x 454
10------Lockwasher, 9/164
11------Capscrew, 1/2-13 x 1-1/48
1236174Bracket, Mid Mounting1
13------Capscrew, Metric, M8-1.25 x 302
14------Lockwasher, 5/162
15------Flatwasher, 5/162
1636316-1Plate, Left Reinforcement1
1736316-2Plate, Right Reinforcement (Not Shown)1
18------Locknut, 5/8-114
1-33B-2
Page 13
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-5326
New Holland 1310, 1510 & 1710
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
136573Bracket, Right Mid Mounting1
2------Capscrew, 1/2-13 x 1-3/42
336574Bracket, Left Mid Mounting1
4------Capscrew, Metric, M16-2.00 x 408
5------Lockwasher, 5/88
6------Locknut, 1/2-1310
736585Bracket, Front Mounting1
S------Capscrew, 1/2-13 x 1-1/24
9------Capscrew, 1/2-13 x 2"4
10------Locknut, 5/8-112
11------Capscrew, 5/8-11 x 1-3/42
1236556Flat, Spacer (For Use Without Mower On 1310)2
1336578-1Bracket, Left Mounting (For 1310 Only)1
1436578-2Bracket, Right Mounting (For 1310 Only)1
1536576-1Angle, Mounting (LH Side On 1510, RH Side On 1710)1
1636576-2Angle, Mounting (RH Side On 1510, LH Side On 1710)1
1-33B-3
Page 14
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-5497
Case IH 245 & 255
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
137869Bracket, Front Mounting1
236174Bracket, Mid Mounting1
336315-1Bracket, Left Reinforcement1
436315-2Bracket, Right Reinforcement1
536328Spacer, Flat2
6------Capscrew, 5/8-11 x 1-1/24
7------Capscrew, 1/2-13 x 1-1/48
8------Capscrew, Metric, M14-2 x 454
9------Capscrew, Metric, M12-1.25 x 458
138357-1Bracket, Front Mounting, Left1
238357-2Bracket, Front Mounting, Right1
338356Bracket, Mid Mounting2
438276Tube, Mid Cross Tie1
5------Capscrew, 1/2-13 x 3-1/24
6------Capscrew, 1/2 x 4-1/22
7------Capscrew, 1/2 x 1-1/26
8------Locknut, 1/2-1312
924765-2Plastic Trim (Order Per Running Inch)6
1-33B-5
Page 16
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-5577
John Deere 850, 950 & 1050
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
138451Bracket, Front Mounting1
238450Bracket, Mid Mounting1
338453Plate, Spacer2
4------Capscrew, Metric , M14-2 x 404
5------Capscrew, Metric, M12-1.75 x 504
6------Lockwasher, 9/168
7------Lockwasher, 1/24
8------Flatwasher, 1/24
9------Capscrew, Metric, M14-2 x 504
1-33B-6
Page 17
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-5700
New Holland 1320, 1520, 1620 HST, 1715 & 1720
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
139097Bracket,Front Mounting1
238044Bracket,Mid Mounting,Left1
338042Bracket,Mid Mounting,Right1
438049Spacer,Flat4
5------Capscrew, 1/2-13 x 2.004
6------Locknut, 1/2-134
7------Capscrew, Metric, M16-2.00 x 508
8------Lockwasher, 5/88
9------Capscrew, Metric, M16-2.00 x 60 (Used Only With Mower Deck)6
139976Bracket,Front Mounting1
238201Bracket,Mid Mounting,Left1
338202Bracket,Mid Mount,Right1
438049Spacer,Flat2
5------Capscrew, 1/2-13 x 1-3/44
6------Locknut, 1/2-134
7------Capscrew, Metric, M16-2.00 x 508
8------Lockwasher, 5/88
1-33B-10
Page 21
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-5964
Case IH 1130 & 1140
Cub Cadet 7234, 7235, 7260, 7265HST, 7274GD,
7300GD, & 7305HST FWA, 7272 2WD
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
140833+Bracket,Front Mounting1
2------Capscrew, Metric, M12-1.25 x 404
3------Lockwasher, 1/24
440830+Bracket,Mid Mounting,Right1
540829+Bracket,Mid Mounting,Left1
6------Lockwasher, 9/168
7------Capscrew, Metric, M14-2 x 40MM8
1-33B-11
Page 22
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6038
Massey Ferguson 1125, 1140, 1145, 1240,
1250 & 1260 FWA
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
141343+Assembly,Front Mounting1
2------Capscrew, 1/2-13 x 1-3/44
3------Locknut, 1/2-138
441370-1Midmounting,Left1
541370-2Midmounting,Right1
6------Capscrew, 1/2-13 x 1-1/44
7------Lockwasher, 1/214
8------Capscrew, Metric, 14MM-2.00 x 35MM8
9------Lockwasher, 9/168
10------Capscrew, Metric, 12MM-1.75 x 30MM6
1-33B-12
Page 23
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6053
New Holland 1910
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
136543Bracket, Front Mounting1
2------Capscrew, 5/8" x 1-3/4"4
3------Locknut, 5/8"8
436547Bracket, Mid Mounting1
5------Capscrew, Metric, M16-2.0 x 358
6------Lockwasher. 5/8"8
8------Capscrew, 5/8" x 6-1/2"4
935789Clamp. Flat2
1035788-1Bracket, Reinforcing, Left (Not Shown)1
1135788-2Bracket, Reinforcing, Right1
12------Capscrew, 1/2" x 1-1/2"8
13------Locknut, 1/2"8
1-33B-13
Page 24
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6054
Kubota L2250, L2550DT, L2550GST,
L2650GST, L2950GST FWA
JULY, 2011
1-33B-14
Page 25
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6054
Kubota L2250, L2550DT, L2550GST,
L2650GST, L2950GST FWA
REF.PART
NO.NO.DESCRIPTIONQTY.
142917+Bracket, Front Mounting1
239086Bracket, Mid Mounting1
339087Spacer, Mid Mounting2
4------Capscrew, Metric, M14-1.5 x 50 (RH Side Only)4
5------Capscrew, Metric, M14-1.5 x 408
6------Lockwasher, 9/1612
736891-1Bracket, Left Reinforcement1
836891-2Bracket, Right Reinforcement (Not Shown)1
9------Capscrew, 1/2-13 x 1-1/210
10------Flatwasher, 1/24
11------Locknut, 1/2 -1310
JULY, 2011
1-33B-15
Page 26
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6055
Kubota L2850F, L2850DT, L2850GST, L3250F,
L3250DT, L3450GST FWA
JULY, 2011
1-33B-16
Page 27
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6055
Kubota L2850F, L2850DT, L2850GST, L3250F,
L3250DT, L3450GST FWA
REF.PART
NO.NO.DESCRIPTIONQTY.
138796Bracket, Front Mounting1
236647Bracket, Mid Mounting1
339087Spacer, Mid Mounting2
4------Capscrew, Metric, M14-1.5 x 45 (RH Side Only)4
5------Capscrew, Metric, M14-1.5 x 408
6------Lockwasher, 9/1612
736940-1Bracket, Left Reinforcement1
836940-2Bracket, Right Reinforcement (Not Shown)1
9------Capscrew, 1/2-13 x 1-1/26
10------Capscrew, Metric, M12-1.25 x 354
11------Flatwasher, 1/26
12------Lockwasher, 1/24
13------Locknut, 1/2-136
JULY, 2011
1-33B-17
Page 28
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6457
Massey Ferguson 1230 & 1235 FWA
JULY, 2011
1-33B-18
Page 29
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6457
Massey Ferguson 1230 & 1235 FWA
REF.PART
NO.NO.DESCRIPTIONQTY.
145525Bracket, Front Mounting1
245535Bracket, Mid Mounting1
345532Bracket, Rear2
445542Plate, Mounting2
545543Bracket, Support2
645544Spacer Plate1
7------Capscrew, 3/8-16 x 1-1/44
8------Locknut, 3/8-164
9------Capscrew, 1/2-13 x 1-3/412
10------Locknut, 1/2-1312
11------Flatwasher, 1/24
12------Capscrew, Metric, 10MM-1.50 x 30MM12
13------Lockwasher, 7/1612
14------Flatwasher, 3/8 Sae12
15------Capscrew, Metric, 12MM-1.75 x 30MM8
16------Capscrew, Metric, 12MM-1.75 x 40MM4
17------Capscrew, Metric, 12MM-1.75 x 55MM4
18------Lockwasher, 1/216
JULY, 2011
1-33B-19
Page 30
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6449
Kubota L2900GST & DT, L3300GST & DT FWA ROPS,
L3010DT, GST, HST & F, L3410DT, GST & HST
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
142294+Bracket,Front Mounting1
242270+Crossplate1
345295Bracket,Midmounting,Right1
445294Bracket,Midmounting,Left (Not Shown)1
5------Capscrew, Metric 14MM-1.50MM x 35MM12
6------Capscrew, 1/2-13 x 1-1/28
7------Flatwasher, 1/24
8------Lockwasher, 9/1612
9------Locknut, 1/2-138
10------Capscrew, Metric 12MM-1.25 x 90MM4
11------Lockwasher, 1/24
1247209Spacer1
1-33B-20
Page 31
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6503
Kioti LB2214, LB2614, LK2552, LK2554, LK3054,
LK3504 & LK3054XS
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
142152+Bracket, Front Mounting1
241319+Bracket, Mid Mounting1
3------Capscrew, Metric, 12MM-1.25 x 30MM10
4------Capscrew, 1/2-13 x 1-3/48
5------Flatwasher, 1/214
6------Lockwasher, 1/210
7------Locknut, 1/2-138
844402Spacer2
941308+Strut, Hood, Assembly (LK3054 Only)1
1-33B-21
Page 32
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6798
Kubota L2600 & L3000 FWA
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
138538Bracket, Front Mounting1
248703Bracket, Mid Mounting1
339894-1Bracket, Rear Reinforcement, Left1
439894-2Bracket, Rear Reinforcement, Right (Not Shown)1
514139Bushing, Mid Mounting (Use On L2600 Tractor Only)2
648701Spacer, Mid Mounting (Use On L2600 Tractor Only)2
48701Spacer, Mid Mounting (Use On L3000 Tractor Only)4
7------Capscrew, 14MM-1.5 x 50MM (Use On L2600 Tractor Only)2
8------Capscrew, 14MM-1.5 x 40MM4
9------Capscrew, 12MM-1.25 x 35MM4
10------Capscrew, 1/2-13 x 1-3/44
11------Capscrew, 1/2-13 x 1-1/24
12------Lockwasher, 9/168
13------Lockwasher, 1/24
14------Flatwasher, 9/164
15------Flatwasher, 1/28
16------Locknut, 1/2-138
17------Capscrew, 14MM-1.5 x 35MM4
1-33B-22
Page 33
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6805
John Deere 4200, 4300, 4400, 4210, 4310 & 4410
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
148826Mid-Mounting Bracket2
248822-2Bracket. Mounting, Front, Right1
348822-1Bracket, Mounting, Front, Left1
4------Capscrew, Metric, 16MM-2.0MM x 45MM8
5------Lockwasher, 5/88
6------Capscrew, 1/2-13 x 1-3/48
7------Locknut, 1/2-138
8------Capscrew, Metric, 8MM-1.25MM x 75MM1
949039-1Spacer Tube1
10------Flatwasher, 5/161
1-33B-23
Page 34
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-6884
AGCO ST30X FWA ROPS
Massey Ferguson 1233 FWA
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
149385Bracket, Front Mounting1
249379Bracket, Mid Mounting1
349393Plate, Mounting, Right1
449394Plate, Mounting, Left1
5------Capscrew, Metric, 12MM-1.75 x 35MM22
6------Capscrew, Metric, 12MM-1.75 x 45MM12
7------Capscrew, 5/8-11 x 1-3/44
8------Lockwasher, 1/234
9------Locknut, 5/8-114
1-33B-24
Page 35
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-7093
New Holland TC30, T1510, T1520
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
150056+Bracket, Front Mounting1
250059+Bracket, Mid Mounting, Left1
350058Bracket, Mid Mounting, Right1
438049Spacer, Flat4
5------Capscrew, 1/2-13 x 2.004
6------Locknut, 1/2-134
7------Capscrew, Metric, M16-2.00 x 508
8------Lockwasher, 5/88
9------Capscrew, Metric, M16-2.00 x 60 (Used Only With Mower Deck)6
1-33B-25
Page 36
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-7301
Massey Ferguson 1429, 1433, 1433V, 1440, 1440V
AGCO ST35, ST35X, ST40 & ST40X FWA
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
152456Mounting Bracket, Front1
251638-1Mounting Bracket, Mid, Left1
351638-2Mounting Bracket, Mid, Right1
451054+Spacer, Plate2
551053Oscillation Stop, Left1
651052+Oscillation Stop, Right1
7------Capscrew, Metric, 14MM-2.00 x 35MM Class 10.98
8------Capscrew, Metric, 12MM-1.75 x 35MM Class 10.94
9------Capscrew, Metric, 12MM-1.75 x 40MM Class 10.94
10------Capscrew, 1/2-13 x 2" Class 54
1151175-1Nut, Rubber Expansion2
12------Flatwasher, 5/16"4
13------Lockwasher, 9/16"8
14------Locknut, 1/2-13, Type-N4
15------Flatwasher, 1/2"8
16------Lockwasher, 1/2"8
17------Hex Nut, Metric, 12MM-1.75 x 40MM (V & X Models)4
18------Capscrew, 5/16-18 x 1.25 YDP2
1-33B-26
Page 37
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MOUNTING KIT 2-7320
Kubota B7800, B2710 & B2910
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
151547Front Mounting Assembly1
251538Mid Mounting Assembly1
351548Spacer Plate2
4------Capscrew, Metric, 12MM x 1.25MM x 40MM4
5------Capscrew, Metric, 14MM x 1.50MM x 40MM10
6------Capscrew, Metric, 12MM x 1.75MM x 40MM6
7------Capscrew, 9/16 -12 x 1-1/24
8------Capscrew, 1/2 -13 x 1-1/26
146441BucketAssembly, Front, 60"1
250166BucketAssembly, Rear, 60"1
346472-1Pin Assembly, 1" x 4.50"2
446613-1Pin 1" x 4"2
547047PinAssembly, 1" x 3.62"2
646364CylinderAssembly2
7------Capscrew, 5/16-18 x 1.75 Grade 52
8------Locknut, 5/16-182
947046Bolt, Shoulder, 3/8-16 x 18
10------Locknut, 3/8-168
1136665-1Fitting, Union Tee, 9/16-18 SAE2
1238290-12 Hose, .250 x 191
1338290-13 Hose, .250 x 271
1-33C-2
REF.PART
NO.NO.DESCRIPTIONQTY.
146075-4Fitting, Grease, 1/4-28 Straight6
158137-1Strap, Adjustable, 11"2
1638290-14 Hose, .250 x 471
1738290-15 Hose, .250 x 551
1836251-8Hose, .250 x 382
1934853-16 Sleeve, Nylon, 1.59 ID x 35"1
206137-4Coupling, Male2
2131332-7Pin Assembly4
2246443Grabber, Stiffener2
2340218-3Edge, Cutting Jaw1
2422541-16 Edge, Cutting1
2522541-17 Edge, Cutting1
2646686Decal, Warning2
Page 43
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
60” 4 IN 1 BUCKET ASSEMBLY 2-6708
QUICK ATTACH
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
146441BucketAssembly, Front, 60"1
249212BucketAssembly, Rear, 60"1
346472-1Pin Assembly, 1" x 4.50"2
446613-1Pin 1" x 4"2
547047PinAssembly, 1" x 3.62"2
646364CylinderAssembly2
7------Capscrew, 5/16-18 x 1.75 Grade 52
8------Locknut, 5/16-182
947046Bolt, Shoulder, 3/8-16 x 14
10------Locknut, 3/8-164
1136665-1Fitting, Union Tee, 9/16-18 SAE2
1238290-12 Hose, .250 x 191
1338290-13 Hose, .250 x 271
1-33C-3
REF.PART
NO.NO.DESCRIPTIONQTY.
146075-4Fitting, Grease, 1/4-28 Straight6
158137-1Strap, Adjustable, 11"2
1638290-14 Hose, .250 x 471
1738290-15 Hose, .250 x 551
1836251-8Hose, .250 x 382
1934853-16 Sleeve, Nylon, 1.59 ID x 35"1
206137-4Coupling, Male2
2146443Grabber, Stiffener2
2240218-3Edge, Cutting Jaw1
2322541-16 Edge, Cutting1
2422541-17 Edge, Cutting1
2547756Decal, Warning2
Page 44
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
MATERIAL BUCKET-QUICK ATTACH
JULY, 2011
Ref.Part
No.No.DescriptionQty.
1* Bucket 60" Heavy Duty (Includes Cutting Edges)1
*Bucket 68" Heavy Duty (Includes Cutting Edges)1
*Bucket 68” High Volume Light Material Snow Bucket1
*Bucket 72” High Volume Light Material Snow Bucket1
244408+Cutting Edge, Side (60” H.D.)2
344465Cutting Edge, Bottom (60" H.D.)1
51502-1Cutting Edge, Bottom (68" H.D.)1
22541-20Cutting Edge, Bottom (68” H.V.)1
22542-5Cutting Edge, Bottom (72" H.V.)1
* Not sold as repair part. Order from Whole Goods
1-33C-4
Page 45
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL
QUICK ATTACH DEVICE 2-6678
JULY, 2011
REF.PART
NO.NO.DESCRIPTIONQTY.
148700Frame Assembly1
248686Handle2
36075-4Fitting,Grease, 1/4-284
4G9413315+Pin, Spring, 1/4 x 1-1/22
5------Jam Nut, 1/22
647408-1Disc Spring (Belleville)2
747615Pivot Assembly2
847394Pivot Pin2
941903-1Cotter Pin, 5/32 x 12
1047618Spade Bolt Assembly2
1147614Spring2
1241902-14Clevis Pin, 3/8 x 1-3/82
1348687Latch Pin2
1447526Spring Guide Assembly2
1555580Sheet, Decal, (Includes Two Decals)1
35762Replacement, Oil Line Tee Fitting
35763Replacement, Oil Line 90° Fitting
35764Replacement, Oil Line Straight Fitting
35765Repair, Oil Line Tube Splice Fitting
*NOTE: If a fitting or oil line is damaged, it can be repaired with replacements listed rather than replacing the
complete oil line. No specific tools are required, only common wrenches and a hacksaw.
**NOTE: Because of difficulty in shipping oil line tubes, they have been broken down into sections for shipping. The two sections of tube must be threaded together to construct the original one piece tube which is not
available for repairs.