Washing Machine
Installation & User Instructions – Please keep for future reference F841QW
F841QS
F841QB
F841QW-F841QS-F841QB
Important – Please read these instructions fully before installing or using
These instructions contain important information which will help you get the best from your appliance and ensure safe and correct installation, use and maintenance.
If you need help or have damaged or missing parts, call the
Customer Helpline:0345 257 7271
52157394 - 28/11/14
Contents
If you have damaged or missing parts,
call the Customer Helpline: 0345 257 7271
Safety Information |
2 |
Parts |
3 |
Installation |
4 |
Unpacking your washing machine |
4 |
Removing the packing bolts |
4 |
Adjusting the feet |
4 |
Water inlet hose connection |
5 |
Drain hose connection |
5 |
Electrical connection |
6 |
Introduction of control panel |
7 |
Detergent drawer |
8 |
Program selection |
10 |
Electronic display |
10 |
Auxiliary functions |
12 |
Child Lock |
14 |
Cancelling Programme |
14 |
Finishing Programme |
14 |
Program Selection Guide |
15 |
User Instructions |
16 |
Before first use |
16 |
Preparing for a wash |
16 |
Error Signals |
17 |
Care and Maintenance |
18 |
Water inlet filters |
18 |
Pump filter |
18 |
Detergent drawer |
19 |
Siphon plug |
19 |
Cabinet |
19 |
Drum |
20 |
Trouble Shooting |
21 |
Technical Specifications |
23 |
Guarantee |
24 |
F841QS
F841QS
F841QB
1 EN
Safety Information
|
|
Before use |
During use |
•The installation of this appliance is best carried out by 2 people.
•Dispose of all packing carefully and responsibly.
•This appliance is for indoor use only. Only install in a dry indoor environment.
•The appliance MUST be positioned on a firm level base.
•Do not position the appliance where it is exposed to direct sunlight or heat sources as this will age the plastic and rubber components.
•Warning: Ensure all 4 packing bolts have been removed.
•Ensure the appliance is connected directly to
a domestic mains water supply.
•Warning: This washing machine MUST only be connected to a cold water supply.
•Ensure all electrical connections are as stated in this document.
•Ensure the appliance is plugged into a
separate earthed socket that is easily accessible.
•Ensure the power lead is not trapped under the appliance.
•Do not connect the appliance to the power supply until installation is complete.
•This appliance is for domestic/household use only and is not suitable for commercial use.
•Check that the water hose joints and connections are secure and there are no leaks. If the hoses leak, do not use until the leaks have been stopped.
EN 2
•This appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, Persons with lack of experience and knowledge.
•Do not use a multiple socket or extension cord.
•Do not use if the power lead is damaged. It must be replaced by the manufacturer, their ap-
proved service agent or similarly qualified person.
Customer Helpline: 0345 257 7271.
•Do not insert the plug into the power supply with wet hands.
•Do not touch or use the appliance when barefoot or with wet or damp hands.
•Do not open the detergent drawer during a wash cycle.
•Do not touch the porthole (door) during the washing cycle - it will get hot.
•Never force the machine door open while the machine is running.
•Do not open the door if water is visible through the porthole.
•Do not wash foam rubber or sponge like materials on a hot wash.
•The machine can reach high temperatures
while running. Do not touch the drain hose or waste water during draining.
•Do not forget that the packing material of your machine may be hazardous for children.
•Keep your pet away from your machine.
•Do not use flammable detergent, sprays or dry cleaning agents in or near to the appliance.
•Do not remove or insert the plug in the presence of flammable gas.
•The appliance should not be put on a carpet which can block the air ventilation on the bottom side.
•Do not place heavy objects or sources of heat or damp on top of the washing machine.
•Only use detergents which are suitable for automatic washing machines and follow the detergent manufacturers recommendations.
•Do not use this appliance if there are any missing or damaged parts.
•Do not attempt to repair the appliance
yourself. Contact the manufacturer, their approved service agent or the Customer Helpline: 0345 257 7271.
Parts |
|
|
If you have damaged or missing parts, |
|
||
|
|
call the Customer Helpline: 0345 257 7271 |
|
|||
|
|
|
|
|
||
|
2 |
3 |
4 |
8 |
9 |
|
1 |
|
|
|
|
10 |
|
|
|
|
|
|
|
|
|
|
|
7 |
|
7 |
|
|
|
|
5 |
|
|
|
|
|
|
7 |
|
7 |
|
|
|
|
6 |
|
|
|
|
Front |
|
|
Back |
|
|
1. |
Detergent drawer |
|
|
7.Packing bolt x 4 |
|
|
2. Top panel |
|
|
8.Power lead |
|
||
3. |
Start / Pause button |
|
9.Drain hose |
|
||
4. |
Program selection dial |
|
10.Water inlet |
|
||
5. |
Door |
|
|
|
|
|
6. |
Filter |
|
|
|
|
|
Water inlet hose x 1 |
|
|
Plastic plug x 4 |
|
||
|
|
|
|
|||
|
|
|
|
|
3 |
EN |
Installation
If you have damaged or missing parts,
call the Customer Helpline: 0345 257 7271
Caution: 2 people are required to unpack the washing machine, it is recommended that gloves are worn.
a: Carefully remove all packaging materials including the foam base, dispose of correctly.
Note: When opened, water droplets may be visible in the drum etc. this is normal as each appliance is factory tested.
Important: The packing bolts are designed to support the internal components during transit, these MUST be removed before use.
a:Loosen the screws by rotating counterclockwise with a suitable wrench. (1 & 2)
b:Remove the bolts by pulling them. (3)
c:When the transport bolts have been removed,
insert the plastic transport screw taps found in the accessories bag into the holes. (4)
a:For your machine to work efficiently with minimum vibration it should be settled on flat, nonslippery, firm ground.
b:You can adjust the balance of your machine by changing the positioning of its feet.
c:First, loosen the plastic adjustment nut. (5)
d:Adjust by rotating the feet upwards or downwards. (6)
e:After the desired position has been reached, tighten the plastic adjustment nut again by rotating it upwards.
Note: Never put cartons, wooden blocks or similar materials under the machine to balance irregularities in the level of the ground.
1
X4
3 X4
5
6
X4
2
X4
4
EN 4
Installation
If you have damaged or missing parts,
call the Customer Helpline: 0345 257 7271
7 |
8 |
Important: This washing machine MUST only be connected to a cold water supply.
a: Connect the water inlet hose, the angled connection attaches to the water inlet on the back of the washing machine. (7)
b: The straight connection attaches to the water supply valve. (8)
c: Ensure all seals are in place before connecting.
Important: Only tighten the hose connection nut by hand - do not overtighten.
Important: The height of the top of the curve in the drain hose MUST be between 60 - 100cm from the floor. (9)
Important: The end of the water drain hose may be fitted directly to the waste water outlet hole or a special apparatus mounted on the outlet bracket of the wash-stand.
Important: Never attempt to extend the water drain hose by adding extra parts.
5 EN
Installation
Any electrical work that is required to install this washing machine MUST be carried out by a qualified electrician.
Warning: THIS
APPLIANCE MUST BE
EARTHED
Before making any electrical connections, ensure that:
•Ensure the power socket is suitable for the maximum power of the washing machine (fuses in the power circuit must be 13 amp).
•The supply voltage should be the same as that indicated in the technical specifications (page 17) and the appliance rating plate (located where shown).
•The appliance should be earthed and in compliance with the applicable law.
•Additional earth cables should not be necessary
if the plug and socket are earthed. If necessary, an additional earth cable should be attached to the earth terminal on the back of the washing machine and earthed.
•When installed, the power socket must be within easy reach.
•The use of adapters, multiple connectors or extension cables are not recommended.
•The appliance must be connected to a 220-240 volt 50 cycle AC supply by means of a three pin socket, suitably earthed and protected by a 13 amp fuse.
•Should the fuse need to be replaced, a 13 amp fuse approved to BS1363/A must be used.
•The plug contains a removable fuse cover that must be refitted when the fuse is replaced. If the fuse cover is lost or damaged, the plug must not be used until a replacement cover has been fitted or the plug is replaced.
•A damaged plug should be cut off as close to the plug body as possible, the fuse should be removed and the plug disposed of safely.
If you have damaged or missing parts,
call the Customer Helpline: 0345 257 7271
Plug replacement (UK & Ireland only)
Should you need to replace the plug; the wires in the power cable are coloured in the following way:
Blue – Neutral ‘N’
Brown – Live ‘L’
Green & Yellow – Earth ‘E’
As the colours of the wires in the power cable may not correspond with the coloured markings identifying the terminals in your plug, and proceed as follows:
The green & yellow wire must be connected to the terminal in the plug that is marked with the letter E or by the earth symbol.
The blue wire must be connected to the terminal that is marked with the letter N.
The brown wire must be connected to the terminal that is marked with the letter L.
If the power lead is damaged, it must be replaced by a qualified electrician.
EN 6
Introduction of control panel
Programme knob
Display Panel
Detergent drawer
7 EN
Loading...