Bush BRC100DHEB Instruction manual

Instruction manual

Freestanding Cookers

BRC100DHEB

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

You’ll soon be enjoying your new Freestanding Cooker

It all begins here, with your instructions. Don’t worry,
there’s nothing too technical coming up. Just simple,
step-by-step guidance to get you up and running
quickly. Sound good? Then let’s get started.

Help and Guidance

We’re here to help you get the most from your Freestanding Cooker. Should you require
any guidance, a simple solution can often be found online at:
www.bush-support.com

If you still require further assistance, call one of our experts on 01759 487838.

Contents

Safety information

1

Safety information

2

Getting

to know your

Freestanding Cooker

Ready? Let’s begin

Accessories

Installing your Freestanding

3

Cooker

Installation requirements

Data Label

First Use

Unpacking

Technical Data

Installation details

10

12

14

14

14

14

14

15

Care and Maintenance

5

6

Cleaning

Replacing the lamps

Maintenance

Technical specifications

29

3

3

3

1

2

3

Product support

Troubleshooting

6

Help and assistance

Declaration of conformance to
product standards

Disposal

Guarantee

36

37

38

38

39

Gas Conversion

Using your Freestanding

4

Cooker

Controls

Using the hob top burners

Using the oven

Cooking modes

Practical advice

Cooking guides

19

22

22

23

25

26

26

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

3

1

Safety information

Safety information

Safety information

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Important - Please read these instructions fully before

installing or operating

INSTALLATION WARNINGS

IMPORTANT: This product MUST be installed by a

qualied Gas Safe registered installer in accordance
with local regulations. Particular attention should be
given to the ventilation requirements.

IMPORTANT: Prior to Installation ensure that the local
supply conditions (gas type and pressure, electricity
voltage and frequency) are compatible with the
requirements of your cooker.

IMPORTANT: Carefully unpack and examine the
appliance for any damage. If you think there is a
defect, do not use the appliance and contact Bush
Product Support on 01759 487838. Packaging
materials should be collected together and disposed of
immediately as they may be harmful to children.

IMPORTANT: Keep the electrical cable (not supplied)
of your cooker away from the hot areas of your cooker;
do not let the cable touch the appliance. Keep the
cable away from sharp edges and heated surfaces.

IMPORTANT: Ensure that the electric supply cable is
not trapped or damaged during installation.

IMPORTANT: In the event that the cable connecting
your cooker becomes damaged, it must be replaced
by a suitably qualified person. This cable must not be
replaced by an unauthorised person.

IMPORTANT: Protect your cooker against atmospheric
effects. Do not expose your cooker to effects such as
sun, rain, snow etc.

DURING USAGE

IMPORTANT: This appliance can be used by children

aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been
given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.

WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements. Children less than 8
years of age shall be kept away unless continuously
supervised.

WARNING: Cooking on a hob with fat or oil can
be dangerous and should not be left unattended.

WARNING: NEVER try to extinguish a cooking fire
with water. Instead switch off the appliance and cover
flame e.g. with a lid or a fire blanket.

CAUTION: Cookers may topple forward if a child
climbs onto the cooker door. Children should be
supervised in the kitchen at all times and this cooker
must be secured to the wall using the fixing kit
(included) to prevent accidents.

CAUTION: Do not allow children in the kitchen when
cooking or while cooker parts may still be hot. Many
parts of the cooker will become hot and present a
considerable hazard to children.

IMPORTANT: The materials surrounding the appliance
(cabinets) must be able to withstand a minimum
temperature of 100°C.

IMPORTANT: When using your oven for the first time
your cooker may give off an unusual odour from the
heating elements and insulation materials. This is
normal for new cookers. To eliminate this odour run
the oven at 250 degrees for 40-60 mins with the oven
empty.

WARNING: Before obtaining access to terminals, all
supply circuits must be disconnected.

6

CAUTION: When the oven is hot never touch the oven
glass by hand or with tools.

CAUTION: Before starting to use your appliance,
ensure curtains, paper or flammable items are kept
away from your appliance. Do not keep flammable
materials inside of or around your cooker.

CAUTION: Take care when closing the oven door that
there is nothing obstructing it from closing as this may
break the glass door.

IMPORTANT: When using the grill the oven door must
be kept closed.

Safety information

Safety information

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

Important - Please read these instructions fully before

installing or operating

IMPORTANT: Position pans over the centre of the
burners and turn handles to a safe position where they
can not be knocked or grabbed.

IMPORTANT: Make sure the cooker control knobs are
all in the off position when not in use.

IMPORTANT: If you do not intend to use your cooker
for a long period of time turn off the gas and electric
supply to the cooker.

CAUTION: Using gas cooking appliances results in
the production of heat, moisture and the products of
combustion. Ensure that the room where your cooker
is installed is well ventilated particularly while the
cooker is in use. Keep natural ventilation holes open
or install a mechanical ventilation device (extractor
hood) Prolonged intensive use of your cooker may call
for additional ventilation (by opening a window) or by
increasing the level of mechanical ventilation where
present.

GENERAL SAFETY WARNINGS

IMPORTANT: This appliance has been designed for

non-professional, domestic use only. Do not use this
cooker for commercial use or any other application
e.g. room heating.

WARNING: Danger of fire: do not store flammable
items on or near the cooking surfaces or inside the
oven.

IMPORTANT: When the door of the oven is open, do
not hang or lean anything on it. You may unbalance
your appliance or damage the door or door hinges.

IMPORTANT: Do not hang towels, dishcloths or
clothes from the cooker or its handles.

CLEANING AND MAINTENANCE

IMPORTANT: Always turn the appliance off before

operations such as cleaning or maintenance. You
can do this by switching the cooker off using cooker
isolation switch.

IMPORTANT: Do not remove the control knobs to
clean the control panel.

WARNING: Do not use harsh abrasive cleaners or
sharp metal scrapers to clean the oven door glass
since they can scratch the surface, which may result in
shattering of the glass.

TO MAINTAIN THE EFFICIENCY AND SAFETY
OF YOUR APPLIANCE, WE RECOMMEND YOU
ALWAYS USE OUR AUTHORISED SERVICE
AGENTS AND ORIGINAL SPARE PARTS.

FOR ASSISTANCE CALL BUSH PRODUCT
SUPPORT 01759 487838.

IMPORTANT: Do not try to lift or move this cooker by

pulling on the door handle.

WARNING: Ensure that the appliance is switched off
before replacing the lamp to avoid the possibility of
electric shock.

IMPORTANT: Your appliance is produced in
accordance with all applicable local and international
standards and regulations.

IMPORTANT: Maintenance and repair work must
only be performed by authorised service technicians.
Installation and repair work that is carried out by
unauthorised technicians is dangerous and could
invalidate your guarantee.

7

Getting to know your

Freestanding Cooker

2

Getting to know your Freestanding Cooker

You’ll be up and running in no time

Getting to know your Freestanding Cooker

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Ready? Let’s begin...

Please read these instructions carefully. They contain
important information which will help you get the best
from your Freestanding Cooker and ensure safe and
correct installation and operation.

If you require any further assistance, our technical
experts are happy to help. For full details, refer to
the product support section at the end of these
instructions.

10

Getting to know your Freestanding Cooker

You’ll be up and running in no time

5

2

3

4

1. Oven Door

6

2. Rapid Burner

3. Semi-rapid Burner

1

Auxiliary Burner

4.

Trivets

5.

Burner Control Knobs

6.

7

7

8

Oven light indicator

7.
Function/temperature control knob

8.
Hob top burner control knob

9.

9

8

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

Getting to know your Freestanding Cooker

11

Getting to know your Freestanding Cooker

You’ll be up and running in no time

Oven Accessories

1.
.
.

1.
.
.

1

2

3

1

2

12

3

If you require any technical guidance or fi d that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Getting to know your Freestanding Cooker

Installing your

Freestanding Cooker

3

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Installing your Freestanding Cooker

Bringing it all together

Installation requirements

THIS COOKER MUST BE INSTALLED
ACCORDING TO BS 6172: 2010 BY A SUITABLY
QUALIFIED GAS SAFE REGISTERED INSTALLER

IMPORTANT: CONTACT AN
AUTHORISED SERVICE AGENT FOR
INSTALLATION OF YOUR OVEN!

Data Label

The Data Label is located on the rear of the
appliance.This appliance is suitable for Natural
Gas and Universal LPG; ensure that the available
gas supply matches the Data Label and the gas
type label.

First Use

IMPORTANT: When using your oven for the first time
y the
heating elements and insulation materials. This is
normal for new cookers. To eliminate this odour run
the oven at 250 degrees for 40-60 mins with the
oven empty.

Unpacking

Carefully unpack and examine the appliance for
any damage. If you think there is a defect, do not
use the appliance and contact Product Support on
01759 487838.

Technical Data

BRC100DHEB

Cavity volume (L)

Top element power (W)
Bottom element power (W)

Lamp power (W)

Total power (W)

Energy class

Packaging materials should be collected
together and disposed of immediately as they
may be harmful to children.

Upper right cavity

57 5732

1400

1100 1100

25

2220-2640 1210-1400 2220-2640

A

Upper left cavity Lower left cavity

1400 1400

-

- 25

A

A

14

If you require any technical guidance or f nd that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Installing your Freestanding Cooker

Installing your Freestanding Cooker

Bringing it all together

Installation of Cooker

Gas

This modern cooker was manufactured with parts and
materials of the highest quality and was designed to
meet your cooking needs. You should read this manual
so that you are able to use the cooker correctly and to
avoid any potential problems with using the cooker.
The following information outlines the required rules
for correct installation and service of your cooker. This
is particularly important for the technician who will
install the appliance.

CONTACT AN AUTHORISED SERVICE AGENT FOR
INSTALLATION OF YOUR OVEN!

VENTILATION REQUIREMENTS

For rooms with a volume of less than 5 m³ ­permanent ventilation of 100 cm² is required see figur
1 and 2 for an example.

For rooms with a volume of between 5 m³ and 10m³
a permanent ventilation of 50 cm² will be required
unless the room has a door which opens directly to
the outside, in which case no permanent ventilation is
required.

e

There must be enough natural ventilation to provide
the gas to be used in the environment. The average air

low must directly come in through ventilation from

f
the outside.

Emptying of the Burned Gases from Environment

For cooking appliances that operate with gas, burned
gas wastes are exhausted directly to the outside
or through cooker hoods that are connected to a
chimney that opens directly to the outside. If it is not
possible to install a cooker hood, it is required to set
an electric fan on the window or wall that has access
to fresh air. This electric fan must have the capacity to
change the volume of air in the kitchen environment
4-5 times per hour.

For rooms with a volume greater than 10 m³ - no
permanent ventilation is required.

Attention: Regardless of room size, all rooms
containing the appliance must have direct access to
the outside air via an openable window or equivalent.
The room containing the cooker should have an air

supply in accordance with BS 5440: Part 2.

Environment where your appliance will be installed

Your cooker must be set up and used in a place where
it will always have ventilation. While operating, this
appliance needs 2m3/h air per kw input.

or online at www.bush-support.com If you still req

uire further assistance, call one of our experts on 01759 487838.

Installing your Freestanding Cooker

15

Installing your Freestanding Cooker

Bringing it all together

Gas Connection

IMPORTANT - All Gas installations must be carried
out by a suitably qualified person. For information
on choosing a gas installer contact the ‘Gas Safe
Register’.

www.gassaferegister.co.uk

The appliance can be placed close to other furniture
on condition that the furniture’s height does not
exceed the height of the cooker panel. Make sure that
there are no combustible or flammable materials,
such as curtains, in the vicinity of the installation.

There must be at least 2cm of free space between the
back wall and the rear of the appliance to allow for
ventilation and air circulation.

Figure 3

Positioning

The furniture close to the cooker must be
manufactured resistant to temperatures up to 100°C.

If the kitchen furniture are higher than the hob plate
of the cooker, it must be at least 10cm away from the
cooker’s side.

Surrounding furniture, cabinets and extractor fans
should be positioned in accordance with the diagram
shown. If fited, the extractor fan must be at least
65cm above the hob.

If no fan is fitted the minimum distance between the
hob and any cabinet or other structure must be 70cm.

16

If you require any technical guidance or fi d that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Installing your Freestanding Cooker

Installing your Freestanding Cooker

Bringing it all together

Anti-tilting chain

The cooker is supplied with an anti-tilting chain to prevent the appliance from tilting forward and
causing accidental damage to the gas pipe. Make a hole in the wall behind, at the same height as
the fixing chain. Using the fixing assembly insert the plug into the hole and then screw in the hole
until it is firmly fixed to the wall. Fix the chain to the hook. You can adjust to the level of the cooker
by inserting the feet provided.

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838.

Installing your Freestanding Cooker

17

Installing your Freestanding Cooker

Bringing it all together

Electrical connection

IMPORTANT: Electrical connections must be carried
out by a suitably qualified person and in accordance
with all relevant local building and installation
regulations.

Fitting on a Power Supply Cable

Connecting appropriate power supply terminal board/ connector block:

Using a screwdriver ,prize open tabs of the Terminal board cover.



Remove the wire clamp screw.



Fasten the wires beneath the corresponding screw heads, using brass ‘bridge’ for single phase supply.



Fasten cable clamp and close the cover of the terminal board.



The ac power supply should be 220-240 V, 50/60 Hz. For electric cookers, the minimum 45A fuse, or at least



45A a distribution circuit breaker. For gas cookers, the minimum 20A fuse, or at least 20A circuit breaker.

The electrical cable should not be routed through

any area that may be aected by heat from the

en, especially the area directly behind the oven.

ov

18

If you require any technical guidance or fnd that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Installing your Freestanding Cooker

Installing your Freestanding Cooker

Bringing it all together

Gas Conversion (NG to U-LPG)

CONVERSION TO A DIFFERENT GAS TYPE MUST BE
CARRIED OUT BY A SUITABLY QUALIFIED GAS SAFE
REGISTERED INSTALLER

Changing the jets

1. Remove pan supports, burner heads and caps.

2. Use a size 7 socket wrench to unscrew and remove
the jets, replacing them with those supplied in the
conversion kit. Ensure you use the correct jet for the
corresponding burner.

3. Reassemble the burner heads, caps and pan
supports.

4. Fit the Gas type label supplied in the conversion kit
next to the gas connection point and remove the
existing label.

Setting the minimum lev

1. Light one of the burners and turn the tap to
minimum flame

2.

Remove the control knob which controls the ignited
burner.

3.

Use a thin blade screwdriver to turn the by-pass
screw located above left of the gas valve shaft as
shown below. Turn the by-pass screw fully
clockwise. The result should be a small, stable flam
which is uniform around the entire burner ring. If not,
turn the
with the flame

4. Check that the burner does not go out when the tap

is turned quickly from the maximum to the minimum
position.

5. Repeat for each burner.

by-pass screw anti-clockwise until satisfie

el

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759

487838.

Installing your Freestanding Cooker

19

Using your Freestanding Cooker 4

Using your Freestanding Cooker

Getting the most from your appliance

Controls

Control knob (Hob top Burners)

Upper and lower left cavity

Upper right cavity

Instructions for use (hob top burners)

The symbols on the control knobs mean
the following:

N

Maximum gas flow or ‘high’ flame and
lighting position

Minimum gas flow or ‘low’ flame

All operating positions must be set between the
maximum and minimum flow settings, and
never between the maximum setting and the
closed position.

Gas Burner Components

A Burner cap
B Burner Head
C Burner Bowl
D Thermocouple (where fit ed)
E Electrode

22

MAX

60

80

100

160

120

140

220

200

180

These parts can be removed for cleaning
periodically. After cleaning, they must be well
dried and correctly replaced. It is important to
check that the burner bowl and cap have been
correctly positioned. Failure to do so can cause
serious problems.

If you require any technical guidance or fnd that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Using your Freestanding Cooker

Using your Freestanding Cooker

Getting the most from your appliance

To light the hob burners

To light the burner, press the control knob fully
down and hold the knob down before rotating
anti clockwise to the High Flame position. The
ignition device is integrated into the control knob
and is automatically activated by pushing down
on the control knob.

After lighting the flame, keep the knob pressed for
about 10 seconds: this time is necessary to heat
up the thermocouple and activate the safety valve,

step only applies where flame failure device
is fitted.

In the instance of a power failure, place a lit match
near the burner and proceed as described above.
If the flame doesn't light after the first attempt,
wait 5 minutes for the gas to dissipate before
attempting to re-light the burner.

Once lit, check that the flame is even and turn the
control knob to adjust the flame as required. If the
flame is uneven, check that the ‘burner head/skirt’
and ‘burner cap’ are correctly positioned. To

The use of pans in excess of the maximum
diameter recommended in the table above can
result in over heating/discoloration of hob surface.
During cooking processes involving fa
oils, watch your foods carefully because these
substances may catch fire if overheated

How to use your oven

This freestanding cooker enables the versatility of
cooking by having three operational cavities with
various cooking modes. Each mode can be
selected using the cooking mode and
temperature knob.

To operate the oven:

- Ensure that manual mode is selected.

- Turn the cooking mode selection knob to the

desired cooking mode.

- PLEASE NOTE: When using the 'Grill' 'Warming

oven' and 'Browning oven' these are pre-set to
temperature and cannot be adjusted.

ts and

symbol) Before removing

flame

For correct use of the hob top

use only flat-bottomed pan of dimensions
suitable for the burners, as shown in the table
below. Also as soon as a liquid comes to the boil
take care to turn the flame down to a level that
will just keep it boiling.

Burner Min. Diameter

Large (rapid 150mm 260mm
Medium (semi-rapid) 130mm 180mm
Small (Auxiliary) 90mm 160mm
Triple Flame (Wok) 210mm 270mm

The first time you use your appliance, we
r

ecommend that you set the thermostat to the
highest setting, set the cooking mode selection
knob to a cooking mode and leave the oven
on for about half an hour with nothing in it and
the oven door shut. Then, open the oven door
and allow the oven to cool. Any odour that may
be detected during this initial use is due to the
evaporation of substances used to protect the
oven during storage.

Max. Di

ameter

or online at www.bush support.com If yo

u still require further assistance, call one of our experts on 01759 487838

Using your Freestanding Cooker

23

Using your Freestanding Cooker

Getting the most from your appliance

Positioning the oven trays & shelves

When fitting the trays or shelves, ensure they
are fitted between the moulded edges inside the
cavity that are closest together. Oven Shelves have
a stop so that they are not fully withdrawn by
accident. T
the front of the shelf slightly and withdraw fully
from the oven. Note that the Grill Tray and Baking
Tray do not have a stop position and can be fully
withdrawn without interruption, so be careful not
to accidentally fully withdraw the trays.

Note: Place the Baking Tray provided on the
bottom shelf position of the oven to prevent any
spillages from dripping onto the bottom of the
oven. Never place anything (including foil and

oven trays) on the bottom of the oven when it
is in operation because this could damage the
enamel. Only place your cookware (dishes, trays,

aluminium foil, etc.) on the Oven Shelves
provided with the appliance.

o fully remove the Oven Shelves, lift

24

If you require any technical guidance or find t at your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Using your Freestanding Cooker

Using your Freestanding Cooker

Getting the most from your appliance

MAIN OVEN COOKING MODES

Convection mode
When set to Convection mode, the top and
bottom heating elements operate together like a
‘normal’ conventional oven that you have
probably used before.
Convection mode is best suited for traditional
baking and roasting and you should only use one
shelf at a time, otherwise the heat distribution will
be uneven. You can balance the amount of heat
between the top and the bottom of the dish by
selecting a different shelf height. If you want
more heat at the top of the dish place the dish
on the top or second shelf. For more heat at the
bottom of the dish, place the dish on third or
fourth shelf.

Warming Oven

This setting uses heat produced only by the bottom

element and is pre-set to 250°C.
This gives an ideal setting for cooking pizza.

Grill Mode
Select ‘Grill’ mode with cooking mode selection
knob and turn cooking temperature selection
knob to ‘Max’. When set to Grill mode, the top
inner element operates. The extremely high and
direct temperature of the grill make it possible
to brown the surface of meats and roasts while
locking the juices in to keep the tender. Grill
mode can also be used for dishes that require a
tempera
veal, rib, steak, filets, hamburgers, etc.
Grill food with the oven door closed.

ture on the surface such as beef steaks,

Oven light function

When set to the light function this enables
you to see directly into the cavity or oven.

or online at www.bush-support.com If you still require

further assistance, call one of our experts on 01759 487838

Using your Freestanding Cooker

25

Using your Freestanding Cooker

Getting the most from your appliance

Using your Freestanding Cooker

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Using the Grill

Use the ‘Grill’ mode with the oven door closed,
place the food on the centre of the grill pan,
insert and fit the grill pan on either the 3rd or 4th
shelf from the bottom. Note: only the central part
of the top heating element operates for grilling.

When using ‘Grill’ mode, the thermostat will
automatically set to the highest setting. However,
this does not mean you cannot use lower
temperatures, simply adjust the thermostat knob
to the desired temperature.
PLEASE NOTE: Grill with the door closed at all
times.

Baking cakes

When baking cakes, always place them in a
preheated oven. Make sure you wait until the oven
has been preheated thoroughly (the indicator light
will turn off). T
from dropping, do not open the oven door during
baking.

In general...

... if pastry is too dry
Increase the temperature by 10°C and reduce the
cooking time.

... if pastry has dropped
Use less liquid or lower the temperature by 10°C.

... if pastry is too dark on top

Place it on a lower shelf, lower the temperature,
and increase the cooking time.

o prevent heat loss and the cake

... if cooked well on the inside but sticky on the
outside

Use less liquid, lower the temperature, and
increase the cooking time.

... if the pastry sticks to the pan
Grease the pan well and sprinkle it with a dusting
of flour or use greaseproof paper.

... if I used multi shelf cooking and one shelf is
more cooked

Use a lower temperature setting next time. It is not
necessary to remove the food from all the racks at
the same time.

26

Using your Freestanding Cooker

Getting the most from your appliance

Using your Freestanding Cooker

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

Cooking pizza

For best results when cooking pizza:

• Preheat the oven for at least 10 minutes.

•

Use a light aluminium pizza pan, placing it on
the shelf supplied with the oven. Don’t use the
dripping pan since this will extend the cooking
time, making it difficul

• Do not open the oven door frequently while the
pizza is cooking;

• If the pizza has a lot of toppings (three or four),
we recommend you add the mozzarella cheese
on top halfway through the cooking process.

• For best results, only use one shelf at a time,
but if you want to cook on two shelves, use
the 2nd and 4th racks from the bottom with a
temperature of 220°c and swap them halfway
through cooking.

t to get a crispy crust.

Cooking fish and meat

When cooking white meat, fowl and fish, use a
temperature setting from 180°C to 200°c.

For red meat that you want well done on the
outside while tender and juicy in the inside, it
is best to start with a high temperature setting
(200°C-220°C) for a short time, then turn the oven
down afterwards.

In general, the larger the roast, the lower the
temperature setting. Place the meat on the centre
of the shelf and place the dripping pan beneath it
to catch the fat.

Make sure that the shelf is inserted so that it is
in the centre of the oven. If you would like to
increase the amount of heat from below, use a
lower shelf height. For savoury roasts (especially
duck and wild game), dress the meat with lard or
bacon on the top.

27

Care and maintenance

5

Care and maintenance

Looking after your appliance

Care and maintenance

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Cleaning

WARNING! Isolate the power supply to the cooker and
make sure that the oven is cool.

Before cleaning your oven or performing
maintenance, make sure that the cooking mode
selection knob and the cooking temperature
selection knob is set to ‘OFF’. To extend the life
of your oven, it must be cleaned frequently.

The inside of the oven should preferable be
cleaned immediately after use, when it is still
warm (but not hot), with warm water and
soap. The soap should be rinsed away and the
interior dried thoroughly. Avoid using abrasive
detergents, scourers, acidic cleaners such as lime
scale remover, etc, as these could damage the
enamel, and can result in development of rust
and corrosion. If stains are particularly tough to
remove, use cleaners specifical y recommended
to clean ovens and follow the instructions
provided with the cleaner. Never use steam

cleaner for cleaning inside the oven.

Burner Caps:

Periodically, the enamelled pan support,
enamelled covers and burner heads must be
washed with warm soapy water, rinsed and dried.
After drying them thoroughly, place them back in
their original positions on the burners

Enamelled Parts:

In order to keep enamelled parts as new, it is
necessary to clean them frequently with mild
warm soapy water and then dry with a cloth. Do
not wash them while hot and never use abrasive
powders or abrasive cleaning materials. Do not
leave anything spilled onto enamelled parts for
long periods of time.

Stainless Steel:

Stainless steel parts must be cleaned frequently
with mildly warm soapy water and a soft sponge
and then dried with a soft cloth. Do not use
abrasive powders or abrasive cleaning materials.
Do not leave anything spilled onto stainless steel
parts for long periods of time.

Do not clean using caustic creams, abrasive
cleaning powders, thick wire wool or hard tools.
Enamelled parts of the oven can be damaged
if excess cleaning liquids are not immediately
removed.

After cleaning the interior parts of the oven with a
soapy cloth, rinse it and then dry thoroughly with
a soft cloth.

Clean the glass surfaces with special glass
cleaning agents.

Never use flammable agents like acid, thinner
or petrol when cleaning your oven.

Do not clean your oven with a steam cleaner.

Do not wash any part of your oven in a

dishwasher.

30

Care and maintenance

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

Care and maintenance

Looking after your appliance

Replacing the oven lamps

WARNING: Ensure that the appliance is switched off
before replacing the lamp to av
electric shock.

Remove the glass cover of the lamp-holder as
shown below.

Remove the lamp and replace with a lamp
resistant to high temperatures (300°C) with the
following characteristics:

oid the possibility of

- Voltage: 220-240V

- Wattage: 25W

- Type: E 14

Replacement lamps are available from our
Support Team. Replace the glass cover and
reconnect the oven to the mains power supply.

31

Care and maintenance

Looking after your appliance

Care and maintenance

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Routine maintenance

Have the condition and efficiency of the gas
pipe and the pressure regulator (if installed)
checked periodically. If anomalies are found, do
not repair components but have the faulty
component replaced. To ensure good
performance and safety, the gas regulator taps
must be greased periodically.

Periodic lubrication of the taps and any other
appliance service must only be carried out by
Authorised Personnel.

Abnormal operation

Any of the following are considered to be
abnormal operation and may require servicing:

• Yellow tipping of the burner flame

• Sooting up of cooking utensils.

• Burners not igniting properly.

• Burners failing to remain alight.

• Burners extinguished by cupboard doors.

•

Gas valves, which are difficul

In case the appliance fails to operate correctly,
contact our Support Team on 01759 487838.

t to turn.

32

Care and maintenance

Looking after your appliance

Technical specification

BRC100DHEB

Cavity volume (L)

Top element power (W)
Bottom element power (W)

Lamp power (W)

Total power (W)

Energy class

Upper right cavity

57 5732

1400

1100 1100

25

2220-2640 1210-1400 2220-2640

A

Upper left cavity Lower left cavity

1400 1400

-

- 25

A

A

We apologise for any inconvenience caused by minor inconstancies within these instructions that may
occur due to product improvements and development

All images and drawings are for illustration purposes only.

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

Care and maintenance

33

Product support

6

Product support

Help is always at hand

Product support

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Troubleshooting

If no electrical functions appear to work, check

1.
the cooker isolation switch has not been turned
off also check the fuse in the swit
circuit breaker in you consumer unit

2. After replacing the fuse or resetting the circuit

breaker turn on individual parts of your cooker
one at a time to check function

Problem Possible Cause Solution

ch and the

3. DO NOT ATTEMPT TO REPAIR THIS
COOKER YOURSELF. CALL BUSH PRODUCT
SUPPORT ON 01759 487838 OR CONSULT
A GAS SAFE REGISTERED INSTALLER

Only parts of the cooker
work it may be that the ovens
or the grill, do not work

Nothing works (completely
dead)

The hob burners do not
operate correctly

Links may be missing in
the rear connector box

Power is turned o at
the isolation switch or
the consumer unit

Poor electrical connection

Check if the burner parts
are correctly assembled
(especially after cleaning).

Refer to the Quick Start
Guide to check the correct
placement of the links
This must be done by a
qualified competent person

Ensure isolation switch is on
Check consumer unit has not
tripped out

Have the connections
checked by a qualified
electrician

The gas supply pressure may
be too low/high.
For appliances working with
bottled LPG, the LPG cylinder
may be depleted.

Oven not heating up Oven temperature not set

correctly

Door is not properly
closed

36

Ensure that the correct
temperature has been
selected and the door is
properly closed

Product support

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

Product support

Help is always at hand

Help and assistance

If you require any technical guidance or find that your Freestanding Cooker is not operating as intended, a simple
solution can often be found in the Troubleshooting section of these instructions or online at

www.bush-support.com

If you still require further assistance, call one of our experts on 01759 487838*. To help give us give you a fast and
efficient service please hav

e the following information ready:

Model Ref.

Serial number

Date of purchase

Local call rates applies*

You can find these on
the rating plate - a small
information panel (usually
a sticker or metal plate) on
the rear of your appliance

This will be shown on
your receipt

Lines open 8am-7pm Monday to Saturday and 10am-4pm Sunday.

*Calls to Bush enquiry lines may attract a charge and set up fee from residential lines depending on your call plan/tariff. Mobile and other

s costs may vary, see www.bt.com/pricing for details.

provider

For Security and training purposes, telephone calls to and from customer service centres maybe recorded and monitored. Calls from
Republic of Ireland will attract international call charges.

37

Product support

Help is always at hand

Product support

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,

Declaration of conformance to
product standards

This appliance conforms to all relavant standards
applicable to domestic appliances sold in the UK

Disposal

This appliance/fitting is marked
according to the European directive
2012/19/EU on Waste Electrical

and Electronic Equipment (WEEE).
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise be
caused by inappropriate waste handling of
this product.

The symbol on the product, or on the
documents accompanying the product, the
crossed out wheelie bin symbol, indicates
that this appliance/fitting may not be treated
as household waste. Instead it shall be
handed over to the applicable collection point
for the recycling of electrical and electronic
equipment.

Disposal must be carried out in accordance
with local environmental regulations for waste
disposal.

For more detailed information about
treatment, recovery and recycling of this
product, please contact your local authority,
your household waste disposal service or the
retailer where you purchased the product.

38

Product support

or online at www.bush-support.com If you still require further assistance, call one of our experts on 01759 487838

Call us now and activate your 12 month guarantee

Thank you for choosing Bush. Your new product is guaranteed against faults and
breakdowns for 12 months. Don’t forget to register it with us today so we can provide you
with our best possible after-sales service and useful updates.

www.bushregistration.co.uk

FREEPHONE*

0800 597 8548

Lines are open 8am - 8pm, 365 days a year. *Calls may be recorded and monitored.

Your Bush Guarantee

This product is guaranteed for twelve months from the date of original purchase. Any defect that arises due to
faulty materials or workmanship will be repaired free of charge (or if applicable the product will be replaced or the
purchase price refunded) where possible during this period by the dealer from who your purchased the unit.

The guarantee is subject to the following provisions:

• The guarantee does not cover accidental damage,
misuse, cabinet parts, knobs or consumable items.

• The product must be correctly installed and
operated in accordance with the instructions
contained in the manual.

• It must be used solely for domestic purposes. The
guarantee will be rendered invalid if the product is

re-sold or has been damaged by inexpert repair.

• Specifications are subject to change without notice.

• Bush disclaim any liability for loss or damage arising
from the breakdown of the product.

• This guarantee is in addition to and does not
diminish your statutory or legal rights.

Important Data Protection Information

To find out how we and Domestic & General Insurance Plc use your data please refer to the guarantee
registration material or visit www.bushregistrations.co.uk

Guarantor: Argos Limited - 489 - 499 Avebury Blvd. - Milton Keynes - MK9 2NW

39

Contact:

www.bush-support.com

Helpline: 01759 487838