®
3 PCM1739
SPECIFICATIONS (cont.)
All specifications at +25°C, +VCC = +5V, +V
DD
= +3.3V, system clock = 384fS (fS = 44.1kHz) and 24-bit data, unless otherwise noted.
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
Power Supply Voltage, VDD.............................................................. +4.0V
V
CC
.............................................................. +6.5V
Input Current (except power supply pins) ....................................... ±10mA
Supply Voltage Difference ................................................................ ±0.1V
GND Voltage Difference ................................................................... ±0.1V
Digital Input Voltage........................................................... –0.2V to +5.5V
Digital Output Voltage .............................................. –0.2V to (V
DD
+ 0.2V)
Power Dissipation .......................................................................... 650mW
Operating Temperature Range ............................................. 0°C to +70°C
Storage Temperature...................................................... –55°C to +125°C
Lead Temperature (soldering, 5s) ................................................ +260°C
Package Temperature (IR reflow, 10s) .......................................... +235°C
ABSOLUTE MAXIMUM RATINGS
PACKAGE SPECIFIED
DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT
PACKAGE PACKAGE NUMBER RANGE MARKING NUMBER
(1)
MEDIA
PCM1739E 28-Lead SSOP 324 0 °C to +70°C PCM1739E PCM1739E Rails
" " " " " PCM1739E/2K Tape and Reel
NOTES: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering 2000 pieces
of “PCM1739E/2K” will get a single 2000-piece Tape and Reel.
PACKAGE/ORDERING INFORMATION
PCM1739E
PARAMETER CONDITONS MIN TYP MAX UNITS
POWER SUPPLY REQUIREMENTS
Voltage Range
V
DD
+3.0 +3.3 +3.6 VDC
V
CC
+4.5 +5.0 +5.5 VDC
Supply Current
I
DD
(6)
VDD = 3.3V
f
S
= 44.1 kHz 8.5 12.0 mA
fS = 96kHz, 256f
S
16.5 mA
fS = 192kHz, 128f
S
19.5 mA
I
CC
VCC = 5.0V
fS = 44.1kHz 13.0 18.0 mA
f
S
= 96kHz, 256f
S
14.0 mA
fS = 192kHz, 128f
S
14.5 mA
Power Dissipation V
DD
= 3.3V, VCC = 5.0V
fS = 44.1kHz 93 130 mW
fS = 96kHz, 256f
S
124 mW
f
S
= 192kHz, 128f
S
137 mW
TEMPERATURE RANGE
Operation 070°C
Storage –55 +125 °C
Thermal Resistance
θ
JA
100 °C/W
NOTES: (1) Pins 8, 9, 26, 27, 28 (TEST1, IBIT, DEM0 DEM1, FORM). (2) Pins 23, 24 (ZEROL, ZEROR). (3) Pin 4 (CLKO). (4) Analog performance specs are
tested with Shibasoku #725 THD Meter 400Hz HPF, 30kHz LPF on, average mode with 20kHz bandwidth limiting. The load connected to the analog output is 5kΩ
or larger, AC-coupled. (5) SNR is tested with Infinite Zero Detection off. (6) CLKO is disabled.