Bunn TF Server DSG2 1.0, TF Server DSG2 1.5 Owner's Manual
Digital
ThermoFresh®
1.0 & 1.5 Gallon Server
with Countdown Timer
USE & CARE INFORMATION
CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE #1 of DAILY CLEANING.
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
43240.0011C 7/13 ©2012 Bunn-O-Matic Corporation
INTRODUCTION
This server is intended for use with a BUNN® DUAL® TF DBC®, SINGLE® TF DBC® or ICB family brewers.
When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server
and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf.
NOTE: Calibration of the brewer is required prior to the use of the Digital TF Server.
USER NOTICES
The notices on this server should be kept in good condition. Replace unreadable or damaged labels.
35710.0000
45457.0000
#39043.0000
#39043.0001 #39043.0002
DAILY CLEANING
CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY
NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method
consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing
solution using an approved non-chlorine sanitizer. Do not submerge server.
1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server
completely by opening the faucet.
2. Remove the sensor assembly, fill server with cleaning solution and thoroughly clean the inside of server.
3. Rinse server thoroughly using fresh water rinse.
4. Fill server with sanitizing solution and let the server set for 5 minutes, then drain through fully open faucet.
Thoroughly rinse server after sanitizing.
5. Remove the faucet handle/stem assembly by unscrewing the faucet nut just beneath the faucet handle.
6. Use enclosed cleaning brush to thoroughly clean the faucet body and tube.
7. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts in a mild detergent and water solution. Rinse the parts in hot water. Sanitize the parts for five minutes, thoroughly rinse, then air dry completely.
8. Use enclosed cleaning brush to thoroughly clean the fill tube of the sensor assembly.
NOTE: Never submerge the Digital ThermoFresh
®
Server Display or sensor assembly in water.
9. Wipe sensor assembly with a clean, damp cloth.
10. Reassemble the faucet and attach it to the dispenser.
11. Wash the entire outside surface of the server and display with a clean damp cloth.
PERIODIC CLEANING
1. Remove the sensor assembly from the server.
2. Remove the two thumb screws and slide display assembly from the server.
3. Wipe the surface of the display unit, area under the display unit, and sensor assembly with a clean damp
cloth.
4. Wash the entire outside surface of the sensor assembly with a mild detergent and water solution and rinse
with hot water. Do not submerse. NOTE: Thoroughly cleaning the sensor assembly fins will prevent inaccurate level readings.
5. Replace the display unit and sensor assembly.
2
43240.11 030912
SERVER WITH STAND
REPLACEMENT PARTS
1. 42554.1002 Display Kit, Countdown (Includes items 2 - 4)
42826.1000 Screw, Thumb #6-32 x .25"
2. 46247.1000 Batteries, 4 Pack AAA
3. 42546.0001 Gasket, Battery Cover
4. 42547.0001 Cover, Battery
02361.0000 Screw, Pan Head #4-40 x .25"
5. 43135.0000 Handle, Faucet
6. 35003.0000 Nut, Faucet Spout
7. 00601.1000 Faucet Spring (Package of 6)
8. 29164.1000 Faucet Stem (Package of 6)
9. 00600.1000 Faucet Seat Cup (Package of 6)
10. 42567.0000 Faucet Body
11. 42543.0000 Guard, Faucet
35074.1000 Screw, Pan Head M4 x .7 x .25
43231.0000 Washer, M4 x 9MM
12. 42584.1000 Plug, Front (Package of 10)
13. 42818.1001 Sensor Assy, 1.0 Gal (Includes items 14 &15)
42565.1000 Sensor Assy, 1.5 Gal (Includes items 14 &15)
14. 42563.1002 Cap, Sensor Assy (Package of 5)
15. 39043.0000 Decal, Do Not Submerge
16. 42562.0000* Handle, Server
17. 42758.0000* Shoulder Screw
18. 42585.1000 Plug, Rear (Package of 10)
19. 43246.1000 Cover Assy, Top
42761.0000* Screw, Pan Head M4 x 9
20. 35710.0000 Decal, Warning Hot Liquid
21. 32591.1000 Tube, Silicone .50" ID x 12.0" LG (cut to length)
22. 28526.1000 Tube, Silicone .31" ID x 12.0" LG (cut to length)
23. 42912.0000 Foot, Rubber
43163.0000 Screw, Pan Head #8 x .75"
24. 42295.0001 Elbow, 90°
25. 42890.1000 Base Cover
26. 35016.0001 Insert, Stand
27. 38929.0002 Stand, Server
39617.0000 Screw, Pan Hd Plastite #6 x .75"
28. 38930.0002 Base Plate, Stand
44010.0000 Screw, Pan Head #8 x .50"
29. 39443.1003 Pad, Adhesive Back .75" Dia.
30. 38931.1002 Kit, Drip Tray (Includes item 31)
31. 38932.0000 Cover, Drip Tray
32. 45457.0000* Decal, Do not Submerge
33. 39043.0002* Decal, Do not Spray
34. 39043.0001* Decal, Do not Submerge Server
35. 42889.0000 Seal
36. 35071.0000 Decal, Black Wrap 1.5 Gal. (Not Illustrated)
37974.0000 Decal, Black Wrap 1.0 Gal. (Not Illustrated)
37. 35301.0001 Brush, Cleaning (Not Illustrated)
* Components of item 19
17 16 15 14 13
18
32
19
33
35
20
21
22
23
24
25
26
27
28
29
12 34
1
2
3
4
5
6
7
8
9
10
11
31
P4166
30
3
43240.11 111312
Loading...