Bunn TF Server 1, TF Server 1.5 Owner's Manual

1.0 & 1.5 Gallon

TF SERVER

(With & Without Stand)

USE & CARE INFORMATION

CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE 1 of DAILY CLEANING.

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: [phone] FAX: [phone]

35075.0005B 9/12 ©2012 Bunn-O-Matic Corporation

INTRODUCTION

This server is intended for use with a BUNN® DUAL® TF DBC, SINGLE® TF DBC or ICB coffee brewer only.
When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server
and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf.

USER NOTICES
The notices on this server should be kept in good condition. Replace unreadable or damaged labels.

#26186.0000

DAILY CLEANING

CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY

NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method

consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing
solution using an approved non-chlorine sanitizer. Do not submerge server.

1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server
completely by opening the faucet.

2. Remove the lid, fill server with cleaning solution and thoroughly clean the inside of server.

3. Rinse server thoroughly using fresh water rinse.

4. Fill server with sanitizing solution and let the server set for 5 minutes, then drain through fully open faucet.
Thoroughly rinse server after sanitizing.

5. Remove the faucet handle/stem assembly by unscrewing the faucet nut just beneath the faucet handle.

6. Remove sight gauge shroud by pulling straight up. Remove sight gauge tube and washers.

7. Use enclosed cleaning brush to thoroughly clean the fill tube of the lid assembly, faucet, and sight gauge
tube.

8. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts, lid, and silicone tube in a mild
detergent and water solution. Rinse the parts in hot water. Sanitize the parts for five minutes, thoroughly
rinse, then air dry completely.

9. Reassemble the faucet and attach it, the lid, sight gauge and silicone tube to the dispenser.

10. Wash the entire outside surface of the server with a clean damp cloth.

2

35075.5 030912

SERVER WITH STAND

REPLACEMENT PARTS

1. 43931.1000 Shroud, Sight Gauge 1.5 Gal.
(Includes Item 4)

43931.1001 Shroud, Sight Gauge 1.0 Gal.
(Includes Item 4)

2. 35010.0000 Plate, Decal Mounting

3. 35009.0000 Decal, Bunn

35009.0001 Decal, Plain Black

4. 35004.0000 Backing, Sight Gauge 1.5 Gal.

35004.0001 Backing, Sight Gauge 1.0 Gal.

5. 35005.0000 Sight Gauge Tube 1.5 Gal.

35005.0001 Sight Gauge Tube 1.0 Gal.

6. 39083.0000 Cap, Shroud

7. 02367.0000 Screw, Truss Head #6-32 x .62"

8. 39143.0001 Washer, Sight Gauge Tube

9. 43135.0000 Handle, Faucet, Bunn

43135.1002 Handle, Faucet, Orange

43135.0003 Handle, Faucet, Plain Black

43135.0004 Handle, Faucet, Green

10. 29165.1002 Faucet Bonnet

11. 00601.1000 Faucet Spring (Package of 6)

12. 29164.1000 Faucet Stem (Package of 6)

13. 00600.1000 Faucet Seat Cup (Package of 6)

14. 35074.0000 Screw, Hex Hd Black M4 x .7x25

15. 43930.0000 Spout, Faucet

16. 38932.0000 Cover, Drip Tray

17. 38931.1002 Drip Tray Kit (Includes item 16)

18. 26186.0000 Decal, Warning Hot Liquid

19. 42543.0000 Guard, Faucet

20. 28526.1000 Tube, Silicone .31"ID x 12.0" LG

21. 42295.0001 Elbow, 90°

22. 32591.1001 Tube, Silicone .50" ID x 12.0" LG

23. 35016.0001 Insert, Stand

24. 38929.1002 Stand, Server

25. 39617.0000 Screw, Pan Head #6-32 x .75"

26. 38930.0002 Base Plate, Stand

27. 35365.1000 Lid Assembly 1.5 Gal.

35365.1001 Lid Assembly 1.0 Gal.

28. 39443.1003 Pad, Adhesive Back .75” Dia.

29. 44010.0000 Screw, Pan Head #8-18 x .50”

30. 43231.0000 Washer, M4

31. 42890.1000 Plug, Base Cover

32. 42889.0000 Gasket

33. 42761.0000 Screw, M4 x .7 x 9M

34. 42914.0000 Plug, Top Cover

35. 41366.1001 Kit, Top Cover Assembly (Includes
item 18)

36. 35301.0000 Brush, Cleaning

37. 35071.0000 Decal, Black Wrap 1.5 Gal.

37974.0000 Decal, Black Wrap 1.0 Gal.

27

34

33

35

18

32

20

21

31

22

23

24

25

26

28

6
1
7
2

3

4

8

9
5
10
11
12
13

15

19

30 14

16

17

29

P4194

3

35075.5 090612

SERVER WITHOUT STAND

REPLACEMENT PARTS

1. 43931.1000 Shroud, Sight Gauge 1.5 Gal.

(Includes Item 4)

43931.1001 Shroud, Sight Gauge 1.0 Gal.

(Includes Item 4)

2. 35010.0000 Plate, Decal Mounting

3. 35009.0000 Decal, Bunn

35009.0001 Decal, Plain Black

4. 35004.0000 Backing, Sight Gauge 1.5 Gal.

35004.0001 Backing, Sight Gauge 1.0 Gal.

5. 35005.0000 Sight Gauge Tube 1.5 Gal.

35005.0001 Sight Gauge Tube 1.0 Gal.

6. 02367.0000 Screw, Truss Head #6-32 x .62”

7. 39143.0001 Washer, Sight Gauge Tube

8. 43135.0000 Handle, Faucet, Bunn

43135.1002 Handle, Faucet, Orange

43135.0003 Handle, Faucet, Plain Black

43135.0004 Handle, Faucet, Green

9. 29165.1002 Faucet Bonnet

10. 00601.1000 Faucet Spring (Package of 6)

11. 29164.1000 Faucet Stem (Package of 6)

12. 00600.1000 Faucet Seat Cup (Package of 6)

13. 35074.0000 Screw, Hex Hd Black M4 x .7x25

14. 43930.0000 Spout, Faucet

15. 26186.0000 Decal, Warning Hot Liquid

16. 42543.0000 Guard, Faucet

17. 28526.1000 Tube, Silicone .31”ID x 12.0” LG

18. 42295.0001 Elbow, 90°

19. 32591.1001 Tube, Silicone .50”ID x 12.0” LG

20. 35365.1000 Lid Assembly 1.5 Gal.

35365.1001 Lid Assembly 1.0 Gal.

21. 39083.0000 Cap, Shroud

22. 43231.0000 Washer

23. 42890.1000 Plug, Base Cover

24. 42889.0000 Gasket

25. 42761.0000 Screw, M4 x .7 x 9M

26. 42914.0000 Plug, Top Cover

27. 41366.1001 Kit, Top Cover Assembly (Includes

item 15)

28. 35301.0000 Brush, Cleaning

29. 35071.0000 Decal, Black Wrap 1.5 Gal.

37974.0000 Decal, Black Wrap 1.0 Gal.

20

26

25

27

15

24

17

18

23

19

21

1
6
2

3

4

7

8
5
9

10

11

12

14 16 22 13

P4195

4

35075.5 090612

STAND FOR SERVERS WITHOUT STAND

REPLACEMENT PARTS

- 39795.0003 Stand, Assy (Includes items 1 - 8)

1. 39449.0005 Bracket, Rear

2. 39448.0003 Bracket, Front

3. 38929.0001 Stand, Server (Early Models)

38929.1002 Stand, Server (Late Models)

4. 00970.0000 Nut, Keps #8-32

5. 38930.0001 Base Plate, Stand (Early Models)

38930.0002 Base Plate, Stand (Late Models)

44010.0000 Screw, Pan Head #8-18 x .50"

6. 39443.1003 Pad, Adhesive Back .75" Dia.

7. 38932.0000 Cover, Drip Tray

8. 38931.1000 Drip Tray (Early Models)

38931.0002 Drip Tray (Late Models)

2

1

5

6

3

4

7

8

5

35075.5 030912

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:

1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal

servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor.

2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below:

a) Electronic circuit and/or control boards - parts and labor for 3 years.
b) Compressors on refrigeration equipment - 5 years parts and 1 year labor.
c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis

- parts and labor for 4 years or 40,000 pounds of coffee, whichever comes first.

These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by
it will be commercially free of defects in material and workmanship existing at the time of manufacture and ap­pearing within the applicable warranty period. This warranty does not apply to any equipment, component or
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,
alteration, improper installation or operation, improper maintenance or repair, non periodic cleaning and des­caling, equipment failures related to poor water quality, damage or casualty. In addition, the warranty does not
apply to replacement of items subject to normal use including but not limited to user replaceable parts such as
seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be
made under this warranty by telephone at [phone] or by writing to Post Office Box 3227, Springfield,
Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN
service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN

are not authorized to make modifications to this warranty or to make additional warranties that are binding on
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and
should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts
and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace
the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE
OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT
BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost
sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substi­tute equipment, facilities or services, or any other special, incidental or consequential damages.

392, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN
Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic,
Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design,
Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, In­tellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with
the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel,
Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh,
Titan, trifecta, Velocity Brew, A Partner You Can Count On, Air Brew, Air Infusion, Beverage Bar Creator, Beverage Profit
Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer
Control, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Tea At Its Best, The Horizontal Red Line, Ultra are
either trademarks or registered trademarks of Bunn-O-Matic Corporation.

6

35075.5 030912